Thermogravimetric and Fourier‐transform infrared analyses on the cure behavior of polycardanol containing epoxy groups cured by electron beam

In this study, the curing behavior of polycardanol containing epoxy groups (diepoxidized polycardanol) was exploited in terms of thermal stability and the cure reaction conversion by means of thermogravimetric analysis and Fourier‐transform infrared spectroscopy, respectively. The effect of photo‐initiator type and concentration and electron beam absorption dose in the presence of cationic photo‐initiators (triarylsulfonium hexafluorophosphate (P‐type) and triarylsulfonium hexafluoroantimanate (Sb‐type) on the cure behavior of diepoxidized cardanol (DEC) resin was investigated. The thermal stability of DEC with Sb‐type photo‐initiator was higher than that with P‐type one, being increased with increasing the concentration and electron beam absorption dose. The conversion of cure reaction was gradually increased with increasing the dose, showing the maximum at 800 kGy. The results revealed that Sb‐type photo‐initiator, the concentration of 2 or 3 wt %, and electron beam absorption dose of about 800 kGy may be preferable for initiating epoxy ring opening in the DEC molecules as well as for efficiently curing the DEC resin by electron beam irradiation. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41599.     

Synthesis of a self‐emulsifiable waterborne epoxy curing agent based on glycidyl tertiary carboxylic ester and its cure characteristics

A novel self‐emulsifiable waterborne amine‐terminated curing agent for epoxy resin based on glycidyl tertiary carboxylic ester (GTCE) was synthesized through three steps of addition reaction, capping reaction, and salification reaction of triethylene tetramine (TETA) and liquid epoxy resin (E‐44). The curing agent with good emulsifying and curing properties was gradually obtained under condition of the molar ratio of TETA: E‐44 as 2.2: 1 at 65 °C for 4 h, 100% primary amine capped with GTCE at 70 °C for 3 h, and 20% salifiable rate with glacial acetic acid. The curing agent was characterized by Fourier transform‐infrared spectroscopy (FT‐IR). The curing behavior of the E‐44/GTCE‐TETA‐E‐44 system was studied with differential scanning calorimetry (DSC) and FT‐IR. Results showed that the optimal mass ratio for E‐44/GTCE‐TETA‐E‐44 system was 3 to 1, and the curing agent showed a relatively lower curing temperature. The cured film prepared by the self‐emulsifiable curing agent and epoxy resin under the optimal mass ratio displayed good thermal property, hardness, toughness, adhesion, and corrosion resistance. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44246.     

Investigation on the reaction between polyhexamethylene guanidine hydrochloride oligomer and glycidyl methacrylate

Polyhexamethylene guanidine hydrochloride (PHMG) oligomer is attracting increasing attention for its highly efficient biocidal activity and nontoxicity. To make it bearing carbon‐to‐carbon double bonds and enlarge its application in production of antimicrobial materials via copolymerization, PHMG oligomer was modified via reaction with glycidyl methacrylate (GMA). The influence of reaction parameters on the conversion rate of GMA was investigated using ultraviolet absorption spectroscopy. The structures of PHMG oligomer before and after modification were characterized by Fourier transform infrared spectrometry, Raman spectrometry, nuclear magnetic resonance spectrometry, and electrospray ionization time‐of‐flight mass spectrometry. The results show that carbon‐to‐carbon double bond is successfully introduced into the modified PHMG oligomer. At a feeding molar ratio of GMA to PHMG of 1.0, the conversion rate of GMA reached up to 75% after 60 h of reaction at 60°C in dimethyl sulfoxide. Also, there is an activity difference in the different aminos of PHMG oligomer: the primary amino is ready to react with epoxy of GMA, while the guanidyl amino hardly reacts with GMA due to the p‐π conjugation. Furthermore, the modified PHMG oligomer was used as comonomer to synthesize acrylonitrile copolymer, showing excellent antimicrobial activity against Staphylococcus aureus. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and property of poly(vinyl alcohol) grafted with butyl glycidyl ether

The crosslinked polyvinyl alcohol (CPVA) and alkyl chain grafted CPVA (CPVA‐g‐BGE) were prepared through the addition reaction of epoxy group of epichlorohydrin and butyl glycidyl ether (BGE) with the hydroxyl group of PVA. By FTIR and ¹HNMR analysis, BGE was confirmed to be grafted onto the molecular chain of PVA successfully. By grafting with BGE, the area of the stress–strain curves of CPVA increased, and the elongation at break increased remarkably with little drop of the tensile strength. Much rougher fractured surface with folds was observed, indicating the increased toughness of CPVA. The relaxation peak corresponding to the glass transition temperature (T_g) of CPVA shifted to low temperature with increasing grafting ratio of BGE. When compared with CPVA, the crystallization ability of CPVA‐g‐BGE decreased, indicating that although the intermolecular hydrogen bonding of PVA was weakened by grafting with alkyl chain, appropriate intermolecular association of alkyl chain facilitated the formation of physical entanglement of molecular chains to strengthen and toughen the PVA matrix. Ink contact angles of CPVA‐g‐BGE decreased with increasing grafting ratio of BGE, indicating the increasing compatibility of CPVA with ink, which was advantageous for PVA to be used as surface sizing agent in papermaking. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermal degradation kinetics of insulating/conducting epoxy/Zn composites under nonisothermal conditions

This article deals with the nonisothermal degradation kinetics of insulating and conducting epoxy/Zn composites. A comparison of thermal degradation data obtained from epoxy/Zn composites revealed that the addition of zinc content in epoxy significantly increases its degradation rate. However, the zinc content activates the degradation until its melting point (419.5°C) and then it starts stabilizing the matrix due to its higher specific heat in molten state. Kinetics of the phenomena fairly explains this behavior in terms of the comparison of general kinetic equations for epoxy/Zn composites. It is to notice that both the values of effective activation energy and reaction model (Šestâk Berggren/SB‐m, n) for insulator/conductor composite pair have been found almost the same emphasizing upon negligible polymer–metal interactions in both cases. These mechanistic clues derived from comparative kinetic study have been found in good agreement with the results obtained through morphological analysis of samples by scanning electron microscopy and X‐ray diffraction techniques. POLYM. COMPOS., 34:2049–2060, 2013. © 2013 Society of Plastics Engineers     

Synthesis and properties of elastomer‐modified epoxy–methacrylate sequential interpenetrating networks

The structure and properties of copolymerized sequential‐interpenetrating networks (SeqIPNs) synthesized from amine‐cured epoxies and free‐radical polymerized dimethacrylates were examined. Materials were synthesized with and without the incorporation of an epoxy‐terminated butadiene–nitrile reactive elastomer. Synthesis proceeded through full thermal cure of the epoxy–amine network, followed by polymerization of the methacrylate network. The methacrylate reactions were free‐radically induced using thermal (peroxide‐initiated) or photochemical [electron‐beam (e‐beam)] techniques. Fourier transform infrared spectroscopy was used to monitor epoxy–amine step‐growth polymerization in situ and to measure final cure conversion of methacrylates. Structural examination of the IPNs using atomic force microscopy and scanning electron microscopy revealed microphase separation in the neat–SeqIPN materials and macroscopic phase separation of rubber‐rich domains for elastomer‐modified networks. Dynamic mechanical analysis of the SeqIPN determined that the properties of the network are strongly dependent on the cure conditions. Furthermore, the viscoelastic behavior of the e‐beam–cured SeqIPN could be adequately described by the Williams–Landel–Ferry and Kohrausch–Willams–Watts equations, presumably because of a strong coupling between the epoxy–amine and methacrylate networks. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 530–545, 2001     

Interlaminar fracture toughness of woven fabric composite laminates with carbon nanotube/epoxy interleaf films

The Mode I interlaminar fracture behavior of woven carbon fiber/epoxy composite laminates incorporating partially cured carbon nanotube/epoxy composite films has been investigated. Laminates with films containing carbon nanotubes (CNTs) in the as‐received state and functionalized with polyamidoamine were evaluated, as well as laminates with neat epoxy films. Double‐cantilever beam (DCB) specimens were used to measure G_Ic, the critical strain energy release rate (fracture toughness) versus crack length. Post‐fracture microscopic inspection of the fracture surfaces was performed. Results show that initial fracture toughness was improved with the amino‐functionalized CNT/epoxy interleaf films, but the important factor appears to be the polyamidoamine functionalization, not the CNTs. The initial fracture toughness remained relatively unaffected with the incorporation of neat epoxy and as‐received CNT/epoxy interleaf films. Plateau fracture toughness was unchanged with the use of functionalized CNT/epoxy interleaf films, and was reduced with the use of neat epoxy and as‐received CNT/epoxy interleaf films. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Crystallization behavior of carbon black‐filled polypropylene and polypropylene/epoxy composites

The crystallization behavior of polypropylene (PP)/carbon black (CB) and PP/epoxy/CB composites was studied with differential scanning calorimetry (DSC). The effects of compatibilizer MAH‐g‐PP and dynamic cure on the crystallization behavior are investigated. The nonisothermal crystallization parameters analysis showed that CB particles in the PP/CB composites and the dispersed epoxy particles in the PP/epoxy composites could act as nucleating agents, accelerating the crystallization of the composites. Morphological studies indicated that the incorporation of CB into PP/epoxy resulted in its preferential localization in the epoxy resin phase, changing the spherical epoxy particles into elongated structure, and thus reduced the nucleation effect of epoxy particles. Addition of MAH‐g‐PP significantly decreased the average diameter of epoxy particles in the PP/epoxy and PP/epoxy/CB composites, promoting the crystallization of PP more effectively. The isothermal crystallization kinetics and thermodynamics of the PP/CB and PP/epoxy/CB composites were studied with the Avrami equation and Hoffman theory, respectively. The Avrami exponent and the crystallization rate of the PP/CB composites were higher than those of PP, and the free energy of chain folding for PP crystallization decreased with increasing CB content. Addition of MAH‐g‐PP into the PP/epoxy and PP/epoxy/CB composites increased the crystallization rate of the composites and decreased the chain folding energy significantly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 104–118, 2006     

Study of glycidyl ether as a new kind of modifier for urea‐formaldehyde wood adhesives

In this work, the multiepoxy functional glycidyl ether (GE) modified urea‐formaldehyde (UF) resins were synthesized via a traditional alkaline‐acid process under low formaldehyde/urea (F/U) molar ratio. The synthesized resins were characterized by ¹³C magnetic resonance spectroscopy (¹³C‐NMR), indicating that GE can effectively react with UF resins via the ring‐opening reaction of epoxy groups. Moreover, the residual epoxy groups of GE could also participate in the curing reaction of UF resins, which was verified by Fourier transform infrared spectroscopy. The storage stability of GE‐modified UF resins and the thermal degradation behavior of the synthesized resins were evaluated by using optical microrheology and thermogravimetric analysis, respectively. Meanwhile, the synthesized resins were further employed to prepare the plywood with the veneers glued. For the modification on bonding strength and formaldehyde emission of the plywood, the influences of addition method, type, and amount of GE were systematically investigated. The performance of UF adhesives were remarkably improved by the modification of GE around 20–30% (weight percentage of total urea) in the acidic condensation stage during the resin synthesis. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Cure kinetics and thermal stability of micro and nanostructured thermosetting blends of epoxy resin and epoxidized styrene‐block‐butadiene‐block‐styrene triblock copolymer systems

The compatibility of styrene‐block‐butadiene‐block‐styrene (SBS) triblockcopolymer in epoxy resin is increased by the epoxidation of butadiene segment, using hydrogen peroxide in the presence of an in situ prepared catalyst in water/dichloroethane biphasic system. Highly epoxidized SBS (epoxy content SBS >26 mol%) give rise to nanostructured blends with epoxy resin. The cure kinetics of micro and nanostructured blends of epoxy resin [diglycidyl ether of bisphenol A; (DGEBA)]/amine curing agent [4,4′‐diaminodiphenylmethane (DDM)] with epoxidized styrene‐block‐butadiene‐block‐styrene (eSBS 47 mol%) triblock copolymer has been studied for the first time using differential scanning calorimetry under isothermal conditions to determine the reaction kinetic parameters such as kinetic constants and activation energy. The cure reaction rate is decreased with increasing the concentration of eSBS in the blends and also with the lowering of cure temperature. The compatibility of eSBS in epoxy resin is investigated in detailed by Fourier transform infrared spectroscopy, optical and transmition electron microscopic analysis. The experimental data of the cure behavior for the systems, epoxy/DDM and epoxy/eSBS(47 mol%)/DDM show an autocatalytic behavior regardless of the presence of eSBS in agreement with Kamal's model. The thermal stability of cured resins is also evaluated using thermogravimetry in nitrogen atmosphere. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Cure kinetics of multifunctional epoxies with 2,2′‐dichloro‐4,4′‐diaminodiphenylmethane as hardener

The curing behavior of the epoxy resin N,N,N′,N′‐tetraglycidyldiaminodiphenyl methane (TGDDM) with triglycidyl p‐aminophenol as a reactive diluent was investigated using 2,2′‐dichloro‐4,4′‐diaminodiphenylmethane (DCDDM) as the curing agent. The effect of the curing agent on the kinetics of curing, shelf‐life, and thermal stability in comparison with a TGDDM‐diaminodiphenylsulfone (DDS) system was studied. The results showed a lesser activation energy at the lower level of conversion with a broader cure exotherm for the epoxy‐DCDDM system in comparison with the epoxy‐DDS system, although the overall activation energy for the two systems was comparable. TGA studies showed more stability in the epoxy‐DCDDM system than in the epoxy‐DDS system. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2097–2103, 2000     

Morphology,dynamic rheology,and cohesive properties of epoxy‐modified polyurethane–acrylate microemulsions prepared by in situ surfactant‐free polymerization

A series of organic, solvent‐free, epoxy‐modified polyurethane–acryalte (EPUA) adhesives were prepared through in situ surfactant‐free polymerization. Stable EPUA microemulsions with average particle diameters of less than 100 nm and a unimodal distribution were obtained through control of the epoxy content. Transitions from irregular shapes with a heterogeneous size distribution to a regular spherical particle morphology with an apparent core–shell morphology were obtained for EPUA with an increasing epoxy content to 8 wt %. With epoxy addition, EPUA displayed pseudoplastic behavior instead of Newtonian behavior, and increases in the viscosity and pseudoplastic behavior were detected. In addition, the EPUA emulsion transferred from a viscous liquid to a solidlike liquid. The addition of epoxy was beneficial for phase mixing, interaction, and entanglements between polyurethane and polyacrylate, and the interactions between the EPUA colloidal particles were also enhanced. The thermal stability, mechanical properties, and water and solvent resistance were thereby improved, as was the cohesive properties. However, the corresponding properties were weakened with excessive epoxy, and this was ascribed to the greatly increased particle size, viscosity, and phase separation. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39886.     

UV‐initiated copolymerization route for facile fabrication of epoxy‐functionalized micro‐zone plates

Bisphenol A‐based epoxy acrylate (BABEA), a commercial ultraviolet (UV)‐curable material, was introduced as a new manufacturing material for facile fabrication of epoxy‐functionalized micro‐zone plates through UV‐initiated copolymerization using glycidyl methacrylate (GMA) as the functional monomer. The poly (BABEA‐co‐GMA) was highly transparent in visible range while highly opaque when the wavelength is less than 295 nm, and of high replication fidelity. X‐ray photoelectron spectroscope (XPS) results indicated the existence of epoxy groups on the surface of the poly (BABEA‐co‐GMA), which allowed for binding protein through an epoxy‐amino group reaction. A fabrication procedure was proposed for manufacturing BABEA based epoxy‐functionalized micro‐zone plates. The fabrication procedure was very simple; obviating the need of micromachining equipments, wet etching or imprinting techniques. To evaluate the BABEA‐based epoxy‐functionalized micro‐zone plates, α‐fetoprotein (AFP) was immobilized onto the capture zone for chemiluminescent (CL) detection in a noncompetitive immune response format. The proposed AFP immunoaffinity micro‐zone plate was demonstrated as a low cost, flexible, homogeneous, and stable assay for α‐fetoprotein (AFP). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39787.     

Rheological characterization of UV‐curable epoxy systems: Effects of o‐Boehmite nanofillers and a hyperbranched polymeric modifier

An organo‐modified Boehmite (o‐Boehmite) was used to prepare nanocomposite UV‐curing coatings, based on a cycloaliphatic epoxy resin (3,4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexane carboxylate). A hyperbranched polymer (HBP) based on highly branched polyester, was also added to the resin, with the aim to modify its reactivity, such as a possible route to increase the toughness of the resin. Different amounts of the nanofiller and the HBP, ranging from 5 up to 20 wt % of resin, were dispersed into the resin in the presence of triarylsulfonium hexafluoroantimonate, as a photoinitiator for the UV curing of the resin. The rheological behavior of the formulations produced was studied as function of the shear rate and of the content of each filler using a cone and plate rheometer. A general increase in viscosity was observed with increasing the volume fraction of each filler and a moderate pseudoplastic behavior was observed when o‐Boehmite filler was added. A non‐Newtonian behavior was observed with the incorporation of the HBP. The viscosity of the epoxy/boehmite resin mixtures was analyzed as function of the nanofiller volume fraction. In the case of epoxy/hyperbranched resin mixtures, the Cross equation was used to predict the viscosity of each formulation as a function of the shear rate and an appropriate relationship to predict the viscosity of each formulation as a function of the filler volume fraction, was determined. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of GMA on monodisperse epoxy‐functionalized polymer microsphere particles by dispersion copolymerization of styrene with glycidyl methacrylate

Monodisperse poly[styrene‐co‐glycidyl methacrylate (GMA)] microparticles were synthesized by dispersion copolymerization in a water–ethanol medium. The effects of various polymerization parameters on the particle size and size distribution of the dispersion copolymerization were investigated. The dispersion of polymer particles decreased when the GMA was added if the polystyrene homopolymer particles were polydispersed. The GMA acted as a comonomer as well as a costabilizer in the dispersion copolymerization of styrene with GMA. The solvency of the monomer increased with the concentration of GMA in the polymerization medium because GMA has a greater hydrophilicity than styrene, resulting in a large particle size and a slow polymerization rate. From an HCl–dioxane analysis of the poly(styrene‐co‐GMA) microparticles, great amounts of epoxy groups were detected after the completion of dispersion copolymerization. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1206–1212, 2001     

Toughened polyoxymethylene by polyolefin elastomer and glycidyl methacrylate grafted high‐density polyethylene

Ternary blends of polyoxymethylene (POM), polyolefin elastomer (POE), and glycidyl methacrylate grafted high density polyethylene (GMA‐g‐HDPE) with various component ratios were studied for their mechanical and thermal properties. The size of POE dispersed phase increased with increasing the elastomer content due to the observed agglomeration. The notched impact strength demonstrated a parabolic tendency with increasing the elastomer content and reached the peak value of 10.81 kJ/m² when the elastomer addition was 7.5 wt%. The disappearance of epoxy functional groups in the POM/POE/GMA‐g‐HDPE blends indicated that GMA‐g‐HDPE reacted with the terminal hydroxyl groups of POM and formed a new graft copolymer. Higher thermal stability was observed in the modified POM. Both storage modulus and loss modulus decreased from dynamic mechanical analysis tests while the loss factor increased with increasing the elastomer content. GMA‐g‐HDPE showed good compatibility between the POM matrix and the POE dispersed phase due to the reactive compatibilization of the epoxy groups of GMA and the terminal hydroxyl groups of POM. A POM/POE blend without compatibilizer was researched for comparison, it was found that the properties of P‐7.5(POM/POE 92.5 wt%/7.5 wt%) were worse than those of the blend with the GMA‐g‐HDPE compatibilizer. POLYM. ENG. SCI., 57:1119–1126, 2017. © 2017 Society of Plastics Engineers     

Surface‐grafting of ground rubber tire by poly acrylic acid via self‐initiated free radical polymerization and composites with epoxy thereof

Commercially available recycled ground rubber tire (GRT) particles, found to contain persistent mechano‐free radicals confirmed by electron paramagnetic spectroscopy for the first time self‐initiates free radical polymerization of acrylic acid (AA). The poly acrylic acid (PAA) grafted GRT (PAA‐g‐GRT) was confirmed by Attenuated Total Reflection Fourier Transform Infrared spectroscopy, X‐ray photoelectron spectroscopy, and thermogravimetric analysis (TGA). Epoxy composites using the PAA‐g‐GRT as filler were prepared and their mechanical properties were studied. The PAA‐g‐GRT/epoxy composite showed higher mechanical properties with an increase of modulus up to 180% as compared with the neat GRT/epoxy composite. Surface morphology of GRT, neat GRT/epoxy, and PAA‐g‐GRT/epoxy composites were analyzed by scanning electron microscopy. This technology introduces a new concept to functional and reactive recycling and the cost effective utilization of renewable resource green materials. POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Epoxy/poly(ɛ‐caprolactone) nanocomposites: Effect of transformations of structure on crystallization

The influence of morphology of the epoxy/poly(?‐caprolactone) (PCL) system and corresponding nanocomposites with organophilized layered silicate on PCL crystallization was studied by differential scanning calorimetry, scanning, and transmission electron microscopy. The results obtained indicate a significant affecting of nonisothermal PCL crystallization by phase morphology brought about by the reaction‐induced phase separation (RIPS) influenced either by various nanoclay contents or the epoxy/PCL ratio. Dispersed morphology of PCL matrix with epoxy globules induces crystallization at higher temperatures. The inverse dispersed morphology of epoxy matrix with PCL inclusions causes crystallization at lower temperature. The co‐continuous morphology induces crystallization in both steps. Rate of the second crystallization step is substantially higher than that in the first step. No nucleation effect has been found in the nanocomposites with the added nanofiller. Multicomponent samples show retarded crystallization, i.e., lower crystallinities and lower overall crystallization rate compared with neat PCL. The results obtained suggest that it is primarily morphological/interfacial effects that play a decisive role in the crystallization behavior of PCL in the epoxy/PCL/clay system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3197–3204, 2013     

Characterization and Properties of Reactive Poly(lactic acid)/Polyamide 610 Biomass Blends

A low molecular weight bisphenol‐A type epoxy resin was used as a reactive compatibilizer for poly(lactic acid) (PLA)/polyamide 610 (PA 610) biomass blends. To the best of our knowledge, this blend is the first biomass PA 610 blend in the literature. The epoxy functional groups could react with the terminal groups of both PLA and PA 610. An ester–amide interchange reaction led to a polyester–polyamide copolymer formation, and improved the compatibility of PLA and PA 610. The blends with epoxy resin showed an enhancement in the phase dispersion and interfacial adhesion compared with the blend without epoxy resin. The differential scanning calorimetry (DSC) analysis showed that the crystallization peak temperatures decreased with increasing epoxy content. The melting temperature of PA 610 decreased with the addition of PLA, but remained unchanged with increased compatibilizer dosages. The dynamic mechanical analysis (DMA) showed that the glass transition temperature (T_g) of the blend, with the addition of 0.5 phr epoxy resin, slightly increased compared with that of neat PLA. However, the T_g of the blends remained unchanged with increasing epoxy resin content, and the higher content of epoxy resin in the blends resulted in improved mechanical properties and higher melt viscosity. The unnotched impact test showed that PA 610 could toughen PLA with the addition of epoxy resin. Moreover, the no‐break unnotched impact behavior was observed with the medium content of the compatibilizer, improving the notch sensitivity of PLA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2563–2571, 2013     

Effect of reactive poly(ethylene glycol) flexible chains on curing kinetics and impact properties of bisphenol‐a glycidyl ether epoxy

Bisphenol‐A glycidyl ether epoxy resin was modified using reactive poly(ethylene glycol) (PEO). Dynamic mechanical analysis showed that introducing PEO chains into the structure of the epoxy resin increased the mobility of the molecular segments of the epoxy network. Impact strength was improved with the addition of PEO at both room (RT) and cryogenic (CT, 77 K) temperature. The curing kinetics of the modified epoxy resin with polyoxypropylene diamines was examined by differential scanning calorimetry (DSC). Curing kinetic parameters were determined from nonisothermal DSC curves. Kinetic analysis suggested that the two‐parameter autocatalytic model suitably describes the kinetics of the curing reaction. Increasing the reactive PEO content decreased the heat flow of curing with little effect on activation energy (E_a), pre‐exponential factor (A), or reaction order (m and n). © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012