Formation of a bicontinuous structure membrane of polyvinylidene fluoride in diphenyl ketone diluent via thermally induced phase separation

The polyvinylidene fluoride (PVDF)‐diphenyl ketone (DPK) mixture was studied as a new system to prepare PVDF membranes via thermally induced phase separation (TIPS). The phenomena of liquid–liquid phase separation was found in this mixture when the temperature of mixture was decreasing and the PVDF concentration was less than 30 wt %. Using DPK as diluent, PVDF membrane with bicontinuous structure was obtained without necessity to add a nonsolvent or a stretching process further. The phase diagram of PVDF‐DPK system was also constructed to help investigate the effect of PVDF concentration and coarsening temperature on morphology of resulting membrane. The experiments showed that high coarsening temperatures and low PVDF concentrations resulted in the formation of the large pore size membrane. The strength of the wet membrane was decreasing with decreasing PVDF concentration. On condition that the PVDF concentration was larger than 30 wt %, thermally induced solid–liquid separation occurred and bicontinuous structure disappeared. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of mixed solvents and PVDF types on performances of PVDF microporous membranes

Polyvinylidene fluoride (PVDF) microporous flat membranes were cast with different kinds of PVDFs and four mixed solvents [trimethyl phosphate (TMP)–N,N‐dimethylacetamide (DMAc), triethyl phosphate (TEP)–DMAc, tricresyl phosphate (TCP)–DMAc, and tri‐n‐butyl phosphate (TBP)–DMAc]. The effects of different commercial PVDFs (Solef® 1015, FR 904, Kynar 761, Kynar 741, Kynar 2801) on membrane morphologies and membrane performances of PVDF/TEP–DMAc/PEG200 system were investigated. The membrane morphologies were examined by scanning electron microscopy (SEM). The membrane performances in terms of pure water flux, rejection, porosity, and mean pore radius were measured. The membrane had the high flux of 143.0 ± 0.9 L m^?2 h^?1 when the content of TMP in the TMP–DMAc mixed solvent reached 60 wt %, which was 2.89 times that of the membrane cast with DMAc as single solvent and was 3.36 times that of the membrane cast with TMP as single solvent. Using mixed solvent with different solvent solubility parameters, different morphologies of PVDF microporous membranes were obtained. TMP–DMAc mixed solvent and TEP–DMAc mixed solvent indicated the stronger solvent power to PVDF due to the lower solubility parameter difference of 1.45 MPa^1/2 and the prepared membranes showed the faster precipitation rate and the higher flux. The less macrovoids of the membrane prepared with TEP (60 wt %)–DMAc (40 wt %) as mixed solvent contributed to the higher elongation ratio of 96.61% ± 0.41%. Therefore, using TEP(60 wt %)–DMAc (40 wt %) as mixed solvent, the casting solution had the better solvent power to PVDF, and the membrane possessed the excellent mechanical property. The microporous membranes prepared from casting solutions with different commercial PVDFs exhibited similar morphology, but the water flux increased with the increment of polymer solution viscosity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Formation of an interconnected lamellar structure in PVDF membranes with nanoparticles addition via solid‐liquid thermally induced phase separation

Novel microporous membranes were prepared via thermally induced solid‐liquid (S‐L) phase separation of mixtures containing poly(vinylidene fluoride) (PVDF)/diphenyl ketone (DPK)/nanoparticles [such as montmorillonite (MMT) and polytetrafluoroethylene (PTFE)] in diluted systems with a mass ratio of 29.7/70/0.3 wt %. The crystallization and melting characteristics of these diluted systems were investigated by polarizing optical microscopy (POM), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and wide angle X‐ray diffraction (WAXD). The nanoparticle structure and the interaction between PVDF chains and nanoparticle surfaces determined the crystallization behavior and morphology of the PVDF membrane. The addition of MMT and PTFE had a significant nucleation enhancement on the crystallization of PVDF accompanied by S‐L phase separation during the thermally induced phase separation (TIPS) process. It was observed that an interconnected lamellar structure was formed in these two membranes, leading to a higher tensile strength compared with that of the reference membrane without nanoparticles addition. Additionally, addition of MMT facilitates the fiber‐like β phase crystal formation, resulting in the highest elongation at break. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of microporous PVDF membrane via tips method using binary diluent of DPK and PG

Microporous polyvinylidene fluoride (PVDF) membrane was prepared via thermally induced phase separation (TIPS) method using a binary diluent of diphenyl ketone (DPK) and 1,2‐propylene glycol (PG). The phase diagram for the PVDF/binary diluent of DPK and PG system was measured in the range of the PG/DPK mass ratio changing from 0 to 2/3. Then the effects of the PG/DPK mass ratio and the PVDF concentration on membrane cross‐section structures and tensile strength were also investigated. The results showed that the addition of PG brought about a shift of the cloud point curve to a higher temperature and the extension of the liquid–liquid phase separation region to a higher polymer concentration. Therefore a bicontinuous cross‐section structure was obtained when the PG/DPK mass ratio was 3/7 and the polymer concentration was 30 wt %. As an increase of the PG/DPK mass ratio, the tensile strength increased gradually at a fixed PVDF concentration. Moreover, for the same PG/DPK mass ratio, the cross‐section microstructure changed from a bicontinuous or a cellular structure to a spherulitic structure, and the tensile strength increased drastically as the polymer concentration increased from 20 to 50 wt %. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A biaxial stretched β‐isotactic polypropylene microporous membrane for lithium‐ion batteries

In this article, microporous polypropylene (PP) membranes were produced with TMB‐5 as β‐crystal nucleating agent by biaxial stretching. Influences of different concentration of TMB‐5 were studied using differential scanning calorimetry and X‐ray diffraction. It was found that the highest crystallinity was reached when the nucleating agent content was 0.5 wt %. The effect of stretching temperature and stretching ratio on pore size distribution and porosity of the membranes were investigated by scanning electron microscopy and mercury porosimeter, respectively. And physical properties, such as tensile strength, permeability, and puncture resistance of the microporous membrane prepared at the optimized conditions, were evaluated. Compared with commercial PP separator membrane, the as‐prepared microporous membrane shows similar uniform pore size distribution and exhibits slightly higher porosity and ionic conductivities. When used as lithium‐ion separator, the experimental film shows more stable cycling performance than the commercial one. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45825.     

Fabrication of cellulose acetate ultrafiltration membrane with diphenyl ketone via thermally induced phase separation

With diphenyl ketone as diluent, cellulose acetate (CA) ultrafiltration (UF) membrane with a bicontinuous structure was prepared via thermally induced phase separation (TIPS) method. The liquid–liquid phase separation region of CA/diphenyl ketone system was measured and the maximum corresponding polymer concentration was approximately 53 wt %. The effects of polymer concentration, coarsening time and coarsening temperature on the morphologies, and mechanical properties of CA membranes were investigated systematically. As the polymer concentration increased from 15 to 30 wt %, the bicontinuous structure could be obtained and the tensile strength of CA membranes increased from 3.92 to 30.17 MPa. With the increase of coarsening time, the thickness of dense skin layer and the asymmetry of cross‐section reduced. However, excess coarsening rendered the membrane morphology evolved from a bicontinuous structure to a cellular structure. When the coarsening time was 5 min, the bicontinuous structure in cross‐section showed good interconnectivity and the dense skin layer exhibited a thin thickness of 2 μm. The fabricated CA hollow fiber UF membrane exhibited a high tensile strength of 31.00 MPa and rejection of 96.10% for dextran 20 kDa. It is indicated that diphenyl ketone is a competitive diluent to prepare CA membranes with excellent performance via TIPS. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42669.     

A comparative study of polypropylene nucleated by individual and compounding nucleating agents. I. Melting and isothermal crystallization

In this study, melting and isothermal crystallization behaviors of polypropylene (PP) nucleated with different nucleating agents (NAs) have been comparatively studied. α‐phase NA 1,3 : 2,4‐bis (3,4‐dimethylbenzylidene) sorbitol (DMDBS, Millad 3988), β‐phase NA aryl amides compound (TMB‐5), and their compounds were introduced into PP matrix, respectively. The crystallization and melting characteristics as well as the crystallization structures and morphologies of nucleated PP were studied by differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD), and polarized light microscopy (PLM). As indicated by previous work that a few amounts of α‐phase NA (DMDBS) or β‐phase NA (TMB‐5) has apparent nucleation effect for PP crystallization. However, the crystallization of PP nucleated with compounding NAs is dependent on the content of each NA. In the sample of PP with 0.1 wt % DMDBS and 0.1 wt % TMB‐5, the nucleation efficiency of TMB‐5 is much higher than that of DMDBS and PP crystallization is mainly nucleated by TMB‐5, and in this condition, β‐phase PP is the main crystallization structure. For the sample of PP with 0.2 wt % DMDBS and 0.2 wt % TMB‐5, 0.2 wt % DMDBS has higher nucleation efficiency than 0.2 wt % TMB5, and α‐phase is the main crystalline structure in this sample. The isothermal crystallization kinetics and crystallization structure have been analyzed in detail in this work. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Formation of multilayer poly(acrylic acid)/poly(vinylidene fluoride) composite membranes for pervaporation

Dual‐ and multilayer composite membranes, consisting of poly(acrylic acid) (PAA) and poly(vinylidene fluoride) (PVDF), were synthesized by the plasma‐induced polymerization technique. The dual‐layer membrane had a dense PAA layer grafted onto a microporous PVDF substrate, whereas in the multilayer membranes, the grafted PAA and the PVDF layers were arranged in an alternating sequence (e.g., PAA/PVDF/PAA and PAA/PVDF/PAA/PVDF/PAA). These membranes were used in a pervaporation process to separate ethanol–water solutions. For the dual‐layer membranes, the results indicated that the separation factor increased and the permeation flux decreased with increasing amounts of grafted PAA. For the case of grafting yield < 0.6 mg/cm², the composite membrane demonstrated poor separation. As the grafting yield reached 0.85 mg/cm², a sharp increase of the separation factor was observed. For the multilayer membranes, the pervaporation performances were very good, with high separation factors (on the order of 100) and reasonable permeation fluxes over a wide ethanol concentration range. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2266–2274, 2004     

Detecting crystallization structure evolution of polypropylene injection‐molded bar induced by nucleating agent

The crystallization structures of Polypropylene (PP) injection‐molded bars nucleated by nucleating agent were detected from the skin layer to the core zone, layer by layer. α‐phase nucleating agent 1,3:2,4‐bis (3,4‐dimethylbenzylidene) sorbitol (DMDBS, Millad 3988), β‐phase nucleating agent aryl amides compounds (TMB‐5), and their compounds were introduced into PP matrix, respectively. The relative content of β‐phase PP in the different zones of an injection‐molded bar was characterized and calculated by Wide angle X‐ray diffraction (WAXD) and Differential scanning calorimetry (DSC). The results show that, whether in pure PP or in nucleated PP, both β‐phase PP and α‐phase PP grow in the skin layer of the injection‐molded bar. However, in the intermediate layers and the core zone, the crystallization structures of PP are dependent on the used nucleating agent. β‐phase is the main crystallization structure of TMB‐5 (0.1 and 0.2 wt%) nucleated PP, and α‐phase in DMDBS (0.1 and 0.2 wt%) nucleated PP. Compounding nucleating agents with 0.1 wt% DMDBS and 0.1 wt% TMB‐5 induces PP crystallization almost in β‐phase; however, PP nucleated by 0.2 wt% DMDBS and 0.2 wt% TMB‐5 crystallizes exclusively in α‐phase. The crystallization mechanism of PP nucleated by compounding nucleating agents was further studied in this work. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Effect of the exposure time on the structure and performance of hydrophobic polydimethylsiloxane–poly(vinylidene fluoride) membranes via a non‐solvent‐induced phase separation process in a clean room

The objective of this study was to investigate the effects of the exposure time on the properties and permeability of polydimethylsiloxane (PDMS)–poly(vinylidene fluoride) (PVDF) blend hydrophobic microporous membranes, which were fabricated via a non‐solvent‐induced phase separation process at 25 °C and 60% relative humidity in a clean‐room circumstance. For the prepared PDMS–PVDF membranes, the membrane morphologies were observed by scanning electron microscopy. Crystalline structures were observed by X‐ray diffraction. Pore structures were analyzed by membrane porosity and mean pore size. Hydrophobicity was measured by contact angle measurement, and the mechanical properties were characterized by tensile strength testing. Our study results show that with increasing exposure time from 10 to 110 s, all of the membranes showed a similar pore structure: a spongelike substrate layer with a thin realm of fingerlike structures under the top surface. Phase separation between PDMS and PVDF occurred. The membrane porosity and mean pore radius decreased, and the membrane thickness increased. The membrane hydrophobicity decreased, and the mechanical properties first increased and then decreased. In addition, vacuum membrane distillation experiments were conducted. With the increase in the exposure time from 10 to 110 s, the membrane permeate flux decreased from 16.54 to 6.65 kg m⁻²·h⁻¹, and the salt rejection was higher than 99.9%. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43842.     

Glass fiber reinforced and β‐nucleating agents regulated polypropylene: A complementary approach and a case study

A two‐step process for preparing glass fibers (GFs) reinforced β‐nucleated PP composites was designed and developed. The complementary approach combined GFs reinforcement and β‐nucleating agents regulation using N,N′‐dicyclohexyl‐2,6‐napthalene‐dicarboxamide (TMB‐5) in the presence of maleic anhydride grafted polypropylene (PP‐g‐MA) through extrusion blending. The influence of TMB‐5 and GFs on the mechanical properties and crystallization behavior of PP was studied by mechanical test, wide‐angle X‐ray diffraction, differential scanning calorimetry, and scanning electron microscopy. A distinct complementary effect of GFs and β‐nucleating agent TMB‐5 on mechanical properties and crystallization behavior of PP was observed. Results showed that addition of 20 wt % GFs and 0.1 wt % TMB‐5 into PP matrix with the two‐step process could lead to significant increase to its mechanical properties: specifically 64.8% improvement in tensile strength, 107.1% enhancement in flexural modulus, and 167.7% increasement in notched impact strength compared to that of neat PP. Furthermore, with the combination of TMB‐5 and GFs, not only led to promoted interfacial adhesion, but also significantly improved overall comprehensive mechanical properties. The complementary process provided an alternative approach for the development of PP with balanced toughnesss and stiffness. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45768.     

Crystallization and microporous membrane properties of ultrahigh molecular weight polyethylene with dibenzylidene sorbitol

Dibenzylidene sorbitol (DBS) was chosen as an in situ forming nucleating agent to study ultrahigh molecular weight polyethylene (UHMWPE) crystallization and microporous membrane. The experimental results indicated that DBS self‐assembled into fibrils first and the solution became a physical gel before UHMWPE crystallization during thermally induced phase separation (TIPS) of UHMWPE/liquid paraffin (LP)/DBS solution, and the temperature of DBS self‐assembly shows a strong dependence of DBS concentration. With decreasing temperature further, DBS fibrils as heterogeneous nucleating agent accelerated UHMWPE crystallization, which was showed more clearly in UHMWPE/LP/DBS phase diagram. UHMWPE microporous membranes were prepared through TIPS method with the control of DBS concentration. It was found that UHMWPE microporous membranes in the presence of DBS fibrils show small porous size and low water permeability, but relatively larger mechanical strength. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40706.     

Preparation of PVDF/CaCO3 hybrid hollow fiber membranes for direct contact membrane distillation through TIPS method

Poly(vinylidene fluoride) (PVDF)–CaCO₃ hybrid hollow fiber membranes with a cellular structure and prominent permeability were fabricated via the thermally induced phase separation method for membrane distillation. CaCO₃ nanoparticles were introduced to the casting solution to improve the properties of the membranes. The effect of CaCO₃ dosage on the morphology was investigated. The prepared membranes were characterized by differential scanning calorimetry, SEM, and atomic force microscopy. The results showed that liquid–liquid phase separation preceded solid–liquid phase separation during the spinning process. Low dosages of CaCO₃ had a strong influence on the crystallization of PVDF molecules. The contact angle of the membrane increased with the addition of CaCO₃ nanoparticles. The maximum dead end pure water flux was as high as 1295.5 L/(m² h). The direct‐contact membrane distillation flux of the optimized PVDF/CaCO₃ hybrid membrane achieved 63.98 kg/(m² h) at the feed temperature of 90 °C. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43372.     

Preparation of polypropylene microfiltration membranes via thermally induced (solid–liquid or liquid–liquid) phase separation method

Polypropylene (PP) hollow fiber microfiltration membranes with excellent performance were successfully prepared from the PP‐binary diluent system via thermally induced liquid–liquid (L–L) phase separation method. The binary diluent consisted of myristic acid and diphenyl carbonate. The effects of the binary diluent on phase separation and membrane structure were systematically investigated. With the decrease in the weight ratio of myristic acid to diphenyl carbonate, the Flory–Huggins interaction parameter between PP and the binary diluent became more positive, and the mechanism of phase separation changed from solid–liquid (S–L) to L–L. This resulted in the membrane structure changing from spherulitic to bicontinuous. Moreover, as the weight ratio of myristic acid to diphenyl carbonate decreased from 11/9 to 2/3, the L–L phase separation region kept enlarging while the viscosity of the whole system became higher. The pore size of the cross‐section increased due to the longer coarsening time while the surface pore size decreased due to the higher viscosity of the system. The bulk porosity of resultant PP membranes was mostly higher than 70% and pure water flux were generally larger than 650 L m^?2 h^?1. In addition, the PP hollow fiber microfiltration membrane possessed excellent mechanical properties (tensile strength of 3.47 MPa and elongation of 118%) and good separation performance (rejection to PEO (M_w = 1000 kDa) of 94.6%) when the weight ratio of myristic acid to diphenyl carbonate was 2/3. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42490.     

Crystallization behavior of PVDF in PVDF‐DMP system via thermally induced phase separation

The crystallization behavior of PVDF (poly (vinylidene) fluoride) in PVDF‐dimethylphthalate(DMP) system was investigated in the liquid–liquid (L–L) phase separation region, solid–liquid (S–L) phase separation region and different quenching conditions via thermally induced phase separation (TIPS). Differential scanning calorimetry (DSC) indicated the crystallinity of PVDF in PVDF‐DMP system increased in the early stage of phase separation and polymer‐rich phase crystallized completely in the late stage of phase separation. The scanning electron microscopy (SEM) showed the different quenching temperatures had effects on the spherulite size of polymer rich phase and the ultimate membrane structure in the different phase separation regions. The wide angle X‐ray diffraction (WAXD) was used to quantify the crystal structure of PVDF in PVDF‐DMP system. The α‐phase PVDF was obtained when the system quenched to different temperatures above 40°C, and the area of diffraction peaks changed when quenching temperatures changed. While the β‐phase PVDF was formed when PVDF‐DMP system was quenched form liquid nitrogen and crystallized for 24 h in 25°C water bath. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3714–3719, 2006     

Strong effects of Tween 20 additive on the morphology and performance of poly(vinylidene fluoride) hollow‐fiber membranes

Poly(vinylidene fluoride) (PVDF) hollow‐fiber membranes were prepared from a Tween 20/water/triethyl phosphate/PVDF system. The effects of Tween 20 on the morphology and properties of the membranes were explored. Field emission scanning electron microscopy imaging indicated the presence of skinlike layers on both surfaces of the membranes. In the cross section, a bicontinuous morphology comprised of interlocked crystallites was observed. As the dosage of Tween 20 was raised, the size and quantity of nanopores on the surfaces increased, and the morphology of the crystallites in the cross section changed from sheaflike to sticklike. Tween 20 was removed almost completely during the membrane‐formation process, as validated by Fourier transform infrared–attenuated total reflection and ¹H‐NMR spectrometry. Dextran filtrations were preformed to demonstrate the potential applications of these membranes in separation processes. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44600.     

Synthesis and Characterization of ETS-10/Chitosan Nanocomposite Membranes for Pervaporation

Chitosan (CS) and microporous titanosilicate ETS-10/CS mixed matrix membranes (MMMs) were prepared. The pervaporation performance was tested on the water-ethanol mixtures in the range 85–96 wt.% ethanol. The permeate flux increased from 0.45 to 0.55 kg m^?2 h^?1 at 50°C for the ETS-10/CS MMM with respect to the pure CS membranes. Characterization by SEM and TEM, XRD, DSC, and TGA allowed inferring an intimate contact between the dispersed ETS-10 and the continuous chitosan phase. The 5 wt.% loading of titanosilicate scarcely decreased the hydrophilic character of the mixed matrix membrane but increased the molecular sieving effect on the transport and separation properties, thus affecting the membrane behavior on pervaporation.     

Modified silicone–PVDF composite hollow‐fiber membrane preparation and its application in VOC separation

Polydimethylsiloxane^vi–poly(vinylidene fluoride) (PDMS^vi–PVDF) composite membranes were prepared using asymmetric PVDF hollow‐fiber membranes as the substrate where a very thin layer of silicone‐based coating material was deposited via a developed dip coating method. The preparation of the composite membranes under various conditions were investigated. In the optimal coating procedure, homogenous and stable oligo‐PDMS^vi coating layers as thin as 1–2 μm were successfully deposited on the surface of PVDF membranes. The developed PDMS^vi–PVDF composite membranes were applied for separation of a wide variety of volatile organic compounds (benzene, chloroform, acetone, ethyl acetate, and toluene). The results showed that the PDMS^vi–PVDF hollow‐fiber composite membranes that had been developed exhibited very high removal efficiency (>96%) for all the VOCs examined under favorable operating conditions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Fabrication and characterization of poly(vinylidene fluoride)–polytetrafluoroethylene composite membrane for CO2 absorption in gas–liquid contacting process

The wetting resistance of poly(vinylidene fluoride) (PVDF) membrane is a critical factor which determines the carbon dioxide (CO₂) absorption performance of the gas–liquid membrane contactors. In this study, the composite PVDF–polytetrafluoroethylene (PTFE) hollow fiber membranes were fabricated through dry-jet wet phase-inversion method by dispersing PTFE nanoparticles into PVDF solution and adopting phosphoric acid as nonsolvent additive. Compared with the PVDF membrane, the composite membranes presented higher CO₂ absorption flux due to their higher effective surface porosity and surface hydrophobicity. The composite membrane with addition of 5 wt % PTFE in the dope gained the optimum CO₂ absorption flux of 9.84 × 10⁻⁴ and 2.02 × 10⁻³ mol m⁻² s⁻¹ at an inlet gas (CO₂/N₂ = 19/81, v/v) flow rate of 100 mL min⁻¹ by using distilled water and aqueous diethanolamine solution, respectively. Moreover, the 5% PTFE membrane showed better long-term stability than the PVDF membrane regardless of different types of absorbent, indicating that polymer blending demonstrates great potential for gas separation. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47767.     

Separation of ethanol from ethanol/water mixtures by pervaporation with silicone rubber membranes: Effect of silicone rubbers

In this study, poly(dimethyl siloxane) (PDMS)/poly(vinylidene fluoride) (PVDF), poly(phenyl methyl siloxane) (PPMS)/PVDF, poly(ethoxy methyl siloxane) (PEOMS)/PVDF, and poly(trifluropropyl methyl siloxane) (PTFMS)/PVDF composite membranes were prepared. The different functional compositions of these membranes were characterized by Fourier transform infrared spectroscopy. The surfaces and sections of these membranes were investigated by scanning electron microscopy. The hydrophobicity at the membrane surface was assessed with contact angle measurement. Swelling experiments were carried out to investigate the swelling behavior of these membranes. The composite membranes prepared in this study were used in the pervaporation separation of ethanol/water mixtures, and their separation performances were compared. The results show that the separation performances of these membranes were strongly related to the silicone rubber components and composition, the total fluxes decreased in the following order: PDMS > PPMS > PEOMS > PTFMS. The separation factor followed the following order: PPMS > PEOMS > PDMS > PTFMS (5 wt % ethanol at 40°C). In addition, the effects of the feed temperature (40–70°C) and feed composition (5–20 wt %) on the separation efficiency were investigated experimentally. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011