Noncovalent imprinted microspheres: Preparation,evaluation and selectivity of DBU template

1,8‐diazabicyclo[5.4.0]undec‐7‐ene (DBU) imprinted polymer was prepared as microspheres by precipitation polymerization method to obtain molecular recognition systems based on the noncovalent interactions between DBU template, methacrylic acid (MAA), and ethylene .glycol dimethacrylate (EDMA) in acetonitrile. ¹H NMR analysis of DBU/MAA mixture has been performed and hydrogen bonding interactions have been established. Microspheres have been characterized by FTIR studies with evidence of DBU linkage in polymer particles and by Scanning Electron Microscopy (SEM) to study their morphological properties. How pH values affect the binding capacity of imprinted polymer during the binding stage has been also discussed and results suggest that imprinted poly‐(MAA‐EDMA) behavior is related to the influence of DBU basicity during rebinding processes and the optimum pH value for binding has been found around neutral range. Binding ability of the imprinted polymer towards different concentration of DBU buffered solutions has been evaluated and compared with binding ability of the non‐imprinted polymer. A more sensitive response to the template in the imprinted system suggests that a reasonable number of specific binding sites is formed. Finally, differential selectivity towards other less strong than DBU nitrogen bases, such as pyridine, imidazole, and 1,5‐diazabicyclo[4.3.0]non‐5‐ene (DBN) has been also discussed. Our results indicate that both specific sites and basic properties are involved in the rebinding process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Chelation properties of poly(2‐hydroxy‐4‐acryloyloxybenzophenone) resins toward some divalent metal ions

The chelation behavior of poly(2‐hydroxy‐4‐acryloyloxybenzophenone) [poly(2H4ABP) or polymer I ] obtained through the free‐radical polymerization of 2‐hydroxy‐4‐acryloyloxybenzophenone monomer and for crosslinked polymers prepared from the monomer and known amounts of the crosslinker divinylbenzene (DVB) [4 mol % of DVB for polymer II, 8 mol % of DVB for polymer III, and 16 mol 16% of DVB for polymer IV ] toward the divalent metal ions Cu²⁺, Ni²⁺, Zn²⁺, and Pb²⁺ in aqueous solution was studied by a batch equilibration technique as a function of contact time and pH. The effect of the crosslinker, DVB, was also studied. The metal‐ion uptake of the polymers was determined with atomic absorption spectroscopy, and the highest uptake was achieved at pH 7.0 for polymers I, II, III, and IV. The selectivity and binding capacity of the resins toward the investigated divalent metal ions are discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Preparation,characterization, and metal ion retention capacity of Co(II) and Ni(II) from poly(p‐HO‐ and p‐Cl‐phenylmaleimide‐co‐2‐hydroxypropylmethacrylate) using the ultra filtration technique

p‐Chlorophenylmaleimide and p‐hydroxyphenylmaleimide with 2‐hydroxypropyl methacrylate were synthesized by radical polymerization, and the metal ion retention capacity and thermal behavior of the copolymers were evaluated. The copolymers were obtained by solution radical polymerization with a 0.50 : 0.50 feed monomer ratio. The maximum retention capacity (MRC) for the removal of two metal ions, Co(II) and Ni(II) in aqueous phase were determined using the liquid‐phase polymer based retention technique. Inorganic ion interactions with the hydrophilic polymer were determined as a function of pH. The metal ion retention capacity does not depend strongly on the pH. Metal ion retention increased with an increase of pH for a copolymer composition 0.50 : 0.50. At different pH, the MRC of the poly(p‐chlorophenylmaleimide‐co‐2‐hydroxypropylmethacrylate) for Co(II) and Ni(II) ions varied from 44.1 to 48.6 mg/g and from 41.5 mg/g to 46.0 mg/g, respectively; while the MRC of poly(p‐hydroxyphenylmaleimide‐co‐2‐hydroxypropyl methacrylate) for Co(II) and Ni(II) ions varied from 28.4 to 35.6 mg/g and from 27.2 to 30.8 mg/g, respectively. The copolymers and copolymer–metal complexes were characterized by elemental analysis, FT‐IR, ¹H NMR spectroscopy, and thermal behavior. The thermal behavior of the copolymer and polymer–metal complexes were studied using differential scanning calorimetry and thermogravimetry techniques under nitrogen atmosphere. The thermal decomposition temperature and T_g were influenced by the binding‐metal ion on the copolymer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Fluorenyl‐containing Quaternary Ammonium Poly(arylene ether sulfone)s for Anion Exchange Membrane Applications

A series of anion exchange membranes (AEM) based on block quaternary ammonium poly(arylene ether sulfone) (QA‐bPAES) were successfully synthesized from 9,9′‐bis(4‐hydroxyphenyl) fluorene, 4,4′‐(hexafluoroisopropylidene) diphenol and 4,4′‐difluorodiphenyl sulfone via block polymerization, chloromethylation, quaternization, alkalization and solution casting. Properties of the obtained QA‐bPAES membranes, including ion exchange capacity (IEC), water uptake, swelling ratios, methanol permeability and ion conductivity were investigated. The obtained QA‐bPAES membranes showed low water uptakes, high ion conductivities and good physical and chemical stability. For example, the membrane of QA‐bPAES(20/10)‐1.34 with IEC of 1.34 mmol g⁻¹ exhibited swelling ratios of 5.0% and 5.1% in in‐plane and through‐plane direction, respectively, and ion conductivity of 15.6 mS cm⁻¹ in water at 60 °C with low methanol permeability of 1.06 × 10⁻⁷ cm² s⁻¹ (25 °C). All the results indicated that this type of block membranes had good potentials for alkaline anion exchange membrane fuel cell applications.     

Functionalization of poly(4‐vinyl pyridine) grafted cellulose by quaternization reactions and a study on the properties of postquaternized copolymers

Graft copolymers of 4‐vinyl pyridine (4‐VP) synthesized by using simultaneous gamma irradiation method were further functionalized by post polymer quaternization reactions at N: of the pyridine ring of the graft copolymers. Using the optimum grafting conditions reported earlier for the grafting of 4‐VP onto extracted cellulose, graft copolymer was synthesized in bulk and was further functionalized by quaternization with hexyl bromide (C₆H₁₃Br), benzyl chloride (C₆H₅CH₂Cl), n‐butyl bromide (C₄H₉Br), and maleic anhydride (MAnh). The quaternized polymers were studied for treatment of hardness of water, antibacterial action, emulsification properties, metal ion uptake and stability toward thermal degradation, and enzymatic and alkaline hydrolysis to evaluate the suitability of these polymers in harsh chemical, microbial, and thermal environments. The functionalized polymers were also characterized for surface morphology (SEM), elemental analysis and FTIR for investigations of structural aspects, and to obtain evidence for quaternization. The functionalized copolymers exhibit a range of properties that can be used in many fields of water purification technologies including antibacterial agents and ion exchangers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2454–2464, 2004     

Stable anion exchange membranes derived from fluorinated poly(aryl ethers) with quaternized fluorene units for fuel cell applications

A series of fluorinated poly(aryl ethers) containing benzyltrimethyl quaternary ammonium functionalized fluorene units (QPFAE) are synthesized via condensation polymerization, chloromethylation, and quaternization. Ionomer structure and the ion exchange capacity are confirmed by ¹H‐nuclear magnetic resonance spectroscopy. Other characterization techniques such as Fourier transform infrared spectroscopy, atomic force microscopy, thermogravimetric analysis, gel permeation chromatography, electrochemical impedance spectroscopy, Fenton, water‐swelling, and hydrolytic aging tests are used to evaluate the physicochemical properties of the as‐prepared QPFAE membranes. For the QPFAE membranes with ion exchange capacity of 0.95–1.94 mmol/g, they displayed low water uptake and methanol permeability (4.59–26.1 × 10⁻⁸ cm²/s at 25 °C), fairly good dimensional stability, high mechanical toughness, as well as fine thermal‐oxidative‐hydrolytic stability and ion conductivity at least 10 mS/cm. The membranes also showed clear hydrophilic/hydrophobic phase‐separation morphology. Furthermore, the QPFAE membranes could endure harsh basic conditions (1–4 mol/L NaOH solution) at 60 and 80 °C at least 240 h, keeping rather high mechanical toughness and ion conduction capability during the aging test. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46301.     

Preparation of magnetic ion‐exchange resins by the suspension polymerization of styrene with magnetite

Magnetic polymer microspheres composed of magnetite, styrene, and divinylbenzene were prepared by suspension polymerization to produce magnetic ion‐exchange resins (MIEXs). The magnetite was grafted with oleic acid to improve the magnetic properties of the MIEXs and to prevent the magnetite from flushing out of the MIEXs. The shape and magnetic properties of the magnetic microspheres were investigated with scanning electron microscopy and vibrating‐sample magnetometry. The average diameter of the prepared magnetic polymer microspheres was about 219 μm. The two types of MIEXs were prepared, magnetic cation‐exchange resins (MCEXs) and magnetic anion‐exchange resins (MAEXs). MCEX was prepared by sulfonation of magnetic polymer microspheres, and MAEX was made by a quaternization reaction with triethylamine of chloromethylated magnetic polymer microspheres. With diffuse‐reflectance Fourier transform infrared spectroscopy, elemental analysis, and acid–base titration, the degree of substitution and ion‐exchange capacity of the MIEXs were assessed. The efficiency of each MCEX and MAEX for the purification of contaminated water was examined with Co²⁺ and NO solutions, respectively. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2058–2067, 2003     

Separation of metal ions by water‐insoluble polymers containing sulfonic/sulfonate groups

A water‐insoluble polymer, poly(sodium 4‐styrene sulfonate), was synthesized by radical polymerization at different amounts (2, 4, 6, and 8 mol %) of crosslinking reagent (CR). At the lowest CR level (2 mol %), only a water‐soluble polymer is obtained, and consequently it could not be studied as resin. The polymerization yield ranged from 82.6 to 91.6%. The resin is characterized by FTIR spectroscopy, thermal analysis, and scanning electron microscopy. The metal ion affinity is studied for the cations: Hg(II), Cd(II), Zn(II), Pb(II), Cr(III), and Al(III) with a batch equilibrium procedure under different experimental conditions. The metal ion affinity increased as the pH increased. At pH 5, the resin showed an affinity greater than 97% for all metal ions. Hg(II) showed the highest retention value at pH 2. The maximum retention capacity is determined at optimum pH for Hg(II), Cd(II), Pb(II), and Zn(II). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4328–4333, 2006     

Emulsifier‐free cationic latexes based on vinylbenzyl chloride and 2‐(dimethylamino)ethyl methacrylate with adjusted hydrophilic–hydrophobic properties

Functional emulsifier‐free cationic latexes based on styrenic monomer vinylbenzyl chloride (VBC) and acrylic monomer 2‐(dimethylamino)ethyl methacrylate (DMA) were successfully prepared with dual quaternary ammonium ions (36–63 mol %) on both monomer moieties in two‐stages. First, [2‐(methacryloyloxy)ethyl]dimethylhexadecylammonium bromide monomer (DMA(C₁₆)), prepared via quaternization of DMA with 1‐bromohexadecane, was utilized as a comonomer (5–20%) as well as a surfactant in the emulsion polymerization of VBC. Next, the quaternization of chloromethyl groups in the VBC moiety in latex particles with trimethylamine and N,N‐dimethylhexadecylamine created a second type of quaternized sites on the latex particles. The percentages of the quaternary ammonium ions of the first‐stage latexes (P[VBC‐DMA(C₁₆‐x)]) and the second‐stage latexes (P[VBC(R)‐DMA(C₁₆‐x)]) were determined using bromide and chloride ion‐selective electrodes. The particles were characterized with a scanning electron microscope, Zetasizer, measuring water contact angles of their pellets. The polymer structure and the alkyl group length in their quaternary ammonium ions played an important role on the sizes, zeta potentials and hydrophilic–hydrophobic balances of the latexes. The water contact angles of the pellets of the latex particles varied from 50.3 to 109.6° depending on both the polymer structure and the alkyl group length. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42775.     

Preparation of quaternized poly(vinylidene fluoride) membranes by γ-ray irradiation induced graft polymerization and their antibacterial property

PVDF microfiltration membranes were modified by γ-ray irradiation induced grafting polymerization of 4-vinyl pyridine (4-VP) and then quaternization by n-butyl chloride. The effects of grafting method (simultaneous irradiation, pre-irradiation/UV), grafting conditions (absorbed dose, UV irradiation time, and 4-VP concentration) and quaternization conditions (temperature, time, and concentration of n-butyl chloride) were investigated. It was found that, the grafting degree initially increases with the absorbed dose and then reaches a plateau. The optimal concentration of 4-VP is around 15 wt.%. The ion exchange capacity increases with quaternization temperature, time, and concentration of n-butyl chloride. After modification, the pores size, permeation flux, as well as elongation at break, of quaternized membrane decreases, while the retention coefficient, tensile strength and Young’s modulus increase apparently. Upon contacting with the membranes, the Escherichia coli concentration decreases gradually. It is the adsorption mechanism for the pristine membranes whereas contact-killing mechanism for the quaternized membranes. Simultaneous irradiation is more effective than pre-irradiation/UV in the improvement of antibacterial property of membranes.     

Preparation and characterization of micron‐sized non‐porous magnetic polymer microspheres with immobilized metal affinity ligands by modified suspension polymerization

A novel preparation method of micron‐sized non‐porous magnetic polymer microspheres with immobilized metal affinity ligands was developed. A modified suspension polymerization of methacrylate (MA) and divinylbenzene (DVB) was performed in the presence of oleic acid‐coated magnetic Fe₃O₄ nanoparticles to obtain magnetic poly (methacrylate‐divinylbenzene) (mPMA‐DVB) microspheres. Through ammonolysis using ethylenediamine (EDA) and subsequent carboxymethylation with chloroacetic acid, magnetic polymer microspheres with chelate ligands of iminodiacetic acid (IDA) were obtained. Charging with copper ions resulted in magnetic polymer microspheres capable of binding proteins that display metal affinity. The morphology, magnetic properties, and composition of magnetic polymer microspheres were characterized with scanning electron microscopy (SEM), vibrating sample magnetometer (VSM), and Fourier transform infrared spectroscopy (FTIR), respectively. Bovine hemoglobin (BHb) was adopted as a model protein to investigate their affinity adsorption capacity. It was found that the adsorption capacity was as high as 168.2 mg/g microspheres and with rather low non‐specific adsorption. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2174–2180, 2005     

A Parametric Study of a Monolithic Microfluidic System for On-Chip Biomolecular Separation

A microfabricated poly(dimethylsiloxane) (PDMS) chip containing channel filled with polymer monolith has been developed for on-chip biomolecule separation. Methacrylate monolithic polymers were prepared by photo-initiated polymerization within the channel to serve as a continuous stationary phase. The monolithic polymer was functionalized with a weak anion-exchange ligand, and key parameters affecting the binding characteristics of the system were investigated. The total binding capacity was unaffected by the flow rate of the mobile phase but varied significantly with changes in ionic strength and pH of the binding buffer. The binding capacity decreased with increasing buffer ionic strength, and this is due to the limited available binding sites for protein adsorption resulting from cationic shielding effect. Similarly, the binding capacity decreased with decreasing buffer pH towards the isoelectric point of the protein. A protein mixture, BSA and ovalbumin, was used to illustrate the capacity of the methacrylate-based microfluidic chip for rapid biomolecule separation.     

Synthesis of new ionic crosslinked polymer hydrogel combining polystyrene and poly(4‐vinyl pyridine) and its self‐healing through a reshuffling reaction of the trithiocarbonate moiety under irradiation of ultraviolet light

A new ionic crosslinked polymer hydrogel was achieved by the strategy of ionically crosslinking α,ω‐dibromide terminated polystyrene (Br‐PS‐Br) with poly(4‐vinyl pyridine) (P4VP) which was synthesized by reversible addition‐fragmentation chain transfer polymerization using a chain transfer agent containing a trithiocarbonate moiety. The moiety of trithiocarbonate was introduced into the crosslinked network to show the self‐healing characteristics. The chain structure and components of Br‐PS‐Br and P4VP were characterized through ¹H NMR, gel permeation chromatography, Fourier transform IR spectroscopy and elemental analysis. The P4VP (M_n = 25 300 g mol^?1) chains were crosslinked with Br‐PS‐Br (M_n = 2000 g mol^?1) through the quaternization reaction to form a polymer network which was further crosslinked in acetonitrile by irradiation of UV light to fabricate a hydrogel. Such a hydrogel of P4VP/Br‐PS‐Br cut by a razor blade can be rapidly (1 h) and repeatedly (three times) healed through a reshuffling reaction of the trithiocarbonate moiety under irradiation by UV light. © 2018 Society of Chemical Industry     

Synthesis,characterization, and fluorescence of end‐functionalized polystyrene initiated by 4‐chloromethyl benzoic acid and ethyl 4‐chloromethyl benzenecarboxylate via ATRP

End‐functionalized polystyrene (PSt) was synthesized via atom‐transfer radical polymerization (ATRP) by using 4‐chloromethyl benzoic acid (CMBA) and the ethyl‐protected carboxylic acid, ethyl 4‐chloromethybenzenecarboxylate (ECBC), as initiators respectively. The structure of PSt proved the living‐radical polymerization. Results exhibit both ATRP initiators afforded well‐controlled polymerization with high initiator efficiencies. However, the study also shows the controllability of ATRP can be obviously influenced by using different initiator in different catalyst system. Furthermore, the terminal group of the PSt1, benzoic acid, can coordinate with Europium(III) ion to obtain the polymeric Eu(III) complex, which shows both emissions of polymer and Eu(III) ion. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Poly(1,2‐diaminobenzene) and poly(1,3‐diaminobenzene): Synthesis,characterization, and properties

Poly(1,2‐diaminobenzene) (1,2‐DAB) and poly(1,3‐diaminobenzene) (1,3‐DAB) have been synthesized by using ammonium persulfate as oxidizing agent in the presence and in the absence of the following metal ion salts: CuCl₂, NiCl₂, and CoCl₂ with different HCl concentrations. The products showed a different content of the metal ion depending on the HCl concentration. The polymers were characterized by Fourier transform infrared (FTIR), ultraviolet‐visible (UV‐Vis) spectroscopy, thermal analysis, and electrical conductivity. The polymerization yield depended on the presence of metal ions that can react as oxidizing reagents and/or catalysts. The polymerization mechanism depended on the position of the substituent. For poly(1,2‐DAB) a ladder‐type structure was obtained, and for poly(1,3‐DAB) one similar to that of polyaniline. The thermal stability increased as the metal ion content in the polymer matrix increased. The electrical conductivity of the polymer did not depend on the metal ion content in the polymer. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2564–2572, 2002     

Imprinted β‐cyclodextrin polymers using naringin as template

The objective of this study was to identify a kind of molecular imprinting polymer (MIP) which was suitable for recognizing naringin (NG) in aqueous medium. Based on two crosslinkers (hexamethylene diisocyanate and epichlorohydrin) and two polymerization methods (solution polymerization and emulsion polymerization), four non‐covalent naringin‐β‐cyclodextrine (NG‐β‐CD) imprinted polymers were prepared by using β‐CD as a functional monomer and NG as a template molecule. The binding property and selectivity were evaluated by equilibrium binding experiments. These demonstrated that all the sites in the MIPs show good selective binding ability for NG from naringin dihydrochalcone, a structurally similar molecule. Of the four MIPs, rod‐like 3# MIP which was prepared by emulsion polymerization using hexamethylene diisocyanate as crosslinker exhibited the highest selectivity, its imprinting factor α being 1.53. Scatchard analysis of 3# MIP suggests that there are two classes of binding sites during the MIP's recognition of NG. Additionally, the 3# MIP could be used at least five times without any loss in sorption capacity. Copyright © 2011 Society of Chemical Industry     

Polymeric N‐allyl vinylpyridinium salts as addition–fragmentation type initiators for cationic polymerization

Polymeric allyl pyridinium salts were synthesized from styrene and 4‐vinyl pyridine copolymers by quaternization and counteranion exchange reactions. The initiation capability of these copolymers, in conjunction with a photochemical free radical source such as benzoin, via an addition –fragmentation mechanism in the cationic polymerization of cyclohexene oxide is investigated. © 2001 Society of Chemical Industry     

Ion Imprinted Polymer Solid Phase Extraction (IIP‐SPE) for Preconcentrative Separation of Erbium(III) From Adjacent Lanthanides and Yttrium

Abstract

Erbium(III) ion imprinted polymer (IIP) materials were prepared by photochemical polymerization of the ternary complex, Erbium(III)—5,7‐dichloroquinoline‐8‐ol‐4‐vinylpyridine, with methyl methacrylate (functional monomer) and ethylene glycol dimethacrylate (crosslinking monomer) in the presence of 2,2′‐azobisisobutyronitrile (initiator). The synthesis was carried out in 2‐methoxy ethanol (porogen) medium and the resultant material was filtered, dried and powdered to form unleached polymer particles. The imprint ion (erbium(III)) was removed by stirring the above particles with 6 mol/l HCl to obtain leached polymer particles. These leached particles are termed erbium(III) ion imprinted polymer (IIP) particles as it selectively rebind erbium(III) ions. Non‐imprinted/control polymer (CP) particles were similarly prepared without the imprint ion. CP and unleached and leached IIP particles were characterized by XRD, microanalysis, and UV‐visible spectrophotometric studies. Various parameters that influence ion imprinted polymer—solid phase extraction such as pH, weight of polymer particles, preconcentration time, elution time, eluent volume, and aqueous phase volume were varied and optimal conditions for each parameter for quantitative enrichment of erbium(III) were established. The selectivity coefficients of erbium(III) ion over Y, Dy, Ho and Tm were compared with separation factors reported for two of the best liquid—liquid extractants viz. di‐2‐ethylhexyl phosphoric acid and 2‐ethylhexyl‐ethylhexyl phosphate.     

Synthesis of novel photoresponsive molecularly imprinted polymer microspheres with special binding properties

An azobenzene‐containing molecularly imprinting polymer microsphere with photoresponsive binding properties toward 2,4‐dichlorophenoxyacetic acid (2,4‐D) was successful prepared via silica surface polymerization. The number‐average diameters of silica and imprinting polymer microsphere are 0.5 and 0.7 μm, respectively. The static adsorption, binding and selectivity experiments were performed to investigate the adsorption properties and recognition characteristics of the polymers for 2,4‐D. The equilibrium adsorptive experiments indicated that 2,4‐D‐SMIP(surface molecularly imprinted polymers) has significantly higher adsorption capacity for 2,4‐D than its nonimprinted polymers (SNIP).The binding constant K_d and apparent maximum number Q_max of the imprinted polymer were determined by Scatchard analysis as 0.054 mmol L^?1 and 0.167 mmol g^?1_, respectively. The result of photoregulated release and uptake of 2,4‐D experiment demonstrated that azo‐containing SMIP can make use of light and change it into mechanical properties to release and take up the template molecules. It means that the SMIP can be controlled by light. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 869‐876, 2013     

Radical crossover reactions of a dynamic covalent polymer brush for reversible hydrophilicity control

Reversible hydrophilicity control of a radically exchangeable polymer brush with dynamic covalent linkages was successfully demonstrated. A polymer brush with alkoxyamine units was prepared via surface-initiated atom transfer radical polymerization, and reversible surface hydrophilicity control was achieved via dynamic covalent exchange reactions of alkoxyamines. Exchange reactions between alkoxyamine units in the side chains of the polymer brush and the terminal of poly(4-vinylpyridine) (P4VP) were carried out in order to prepare a side-chain functionalized polymer brush. Subsequent quaternization of P4VP chains with iodomethane was carried out to prepare a more hydrophilic surface. In addition, a de-grafting reaction of the quaternized P4VP side chains was performed to confirm reversibility of the alkoxyamine via radical exchange reactions on the surface. All the composition and wettability changes were investigated via X-ray photoelectron spectroscopy and contact angle measurements.