Biodegradable poly(L‐lactic acid)/poly(butylene succinate‐co‐adipate) blends: Miscibility,morphology, and thermal behavior

Blends of two biodegradable and semicrystalline polymers, poly(L ‐lactic acid) (PLLA) and poly(butylene succinate‐co‐adipate) (PBSA), were prepared by solvent casting in different compositions. The miscibility, morphology, and thermal behavior of the blends were investigated using differential scanning calorimetry and optical microscopy. PLLA was found to be immiscible with PBSA as evidenced by two independent glass transitions and biphasic melt. Nonisothermal crystallization measurements showed that fractionated crystallization behavior occurred when PBSA was dispersed as droplets, evidenced by multiple crystallization peaks at different supercooling levels. Crystallization and morphology of the blends were also investigated through two‐step isothermal crystallization. For blends where PLLA was the major component, different content of PBSA did not make a significant difference in the crystallization mechanism and rate of PLLA. For blends where PBSA was the major component, the crystallization rate of PBSA decreased with increasing PLLA content, while the crystallization mechanism did not change. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Nucleating agent‐containing P(LLA‐mb‐BSA) multi‐block copolymers with balanced mechanical properties

In order to obtain high performance bioplastics and thermoplastic elastomers, P(LLA‐mb‐BSA) multi‐block copolymers containing 30 wt % and 70 wt % soft segment (PLBSA30 and PLBSA70 for short) were synthesized via chain extension and coupling of poly(L‐lactic acid) (PLLA) and poly(butylene succinate‐co‐adipate) (PBSA) prepolymers in the presence of 1% nucleating agent (NA). They were characterized with proton nuclear magnetic resonance (¹H NMR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), polarizing optical microscopy (POM), thermal gravimetric analysis (TGA), transmission electron microscope (TEM), and tensile and impact test. The relatively high molecular weights of (M_n 8200 g/mol and 3100 g/mol for PLLA and PBSA, respectively) the polyester sequences are helpful to improve the PLLA crystallization and the flexibility of the PBSA soft segment. Nucleation effect further accelerates the crystallization of PLLA segment. The synergistic effect of these factors results in good balance between stiffness and toughness. PLBSA30s containing 1% zinc citrate (ZnCC) or talc behave as ultra‐tough bioplastics with ultrahigh impact strength over 50 kJ/m² and excellent tensile properties. PLBSA70 containing 1% ZnCC possesses elongation at break of 600% and retains high modulus (56 MPa) and strength (16 MPa) and therefore behaves as an excellent thermoplastic elastomer. The excellent and balanced properties would extend the end applications of these PLLA‐based materials. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44777.     

Biodegradable poly(butylene succinate‐co‐butylene adipate)/multiwalled carbon nanotube nanocomposites: Preparation,morphology, and crystallization behavior

Biodegradable poly(butylene succinate‐co‐butylene adipate) (PBSA)/multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared via a simple melt‐compounding method at low MWCNTs contents. Scanning and transmission electron microscopy observations revealed a relatively nice dispersion of MWCNTs throughout the PBSA matrix. Both the nonisothermal and isothermal melt crystallizations of PBSA were enhanced significantly in the nanocomposites relative to neat PBSA because of the presence of MWCNTs; however, the crystal structure of PBSA remained unchanged. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Nanocomposites of poly[(butylene succinate)‐co‐(butylene adipate)] (PBSA) and twice‐functionalized organoclay

A new method is described to prepare composites of poly[(butylene succinate)‐co‐(butylene adipate)] (PBSA) with an organophilic clay having a particular functional group, namely twice‐functionalized organoclay (TFC). TFCs were produced by treating Cloisite 25A^® with (glycidyloxypropyl)trimethoxy silane (GPS) or (methacryloyloxypropyl)trimethoxy silane (MPS). Reaction of the silane compound with the organoclay surface was monitored by Fourier‐transform infrared spectroscopy (FTIR). PBSA composites with the three different clays were prepared successfully via melt mixing. The d spacing and the morphology of the composites were monitored by X‐ray diffraction and by transmission electron microscopy. The linear storage modulus of the composites in the melt state increased significantly as a result of incorporation of TFC. Tensile modulus and strength at break of PBSA/TFC–GPS and those of PBSA/TFC–MPS were far superior to those of PBSA/C25A. Copyright © 2005 Society of Chemical Industry     

Elongational rheology of biodegradable poly(lactic acid)/poly[(butylene succinate)‐co‐adipate] binary blends and poly(lactic acid)/poly[(butylene succinate)‐co‐adipate]/clay ternary nanocomposites

A series of blends based on poly(lactic acid) (PLA) and poly[(butylene succinate)‐co‐adipate] (PBSA) as well as their nanocomposites with nanoclay (PLA/PBSA/Clay ternary nanocomposites) were prepared using the twin‐screw extruder. The blends were prepared for PBSA contents ranging from 25 to 75 wt % and their corresponding nanocomposites were prepared at a single‐clay concentration. The morphology and structure of the blends and the nanocomposites were examined using field emission scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction. Rheological properties (dynamic oscillatory shear measurements and elongational viscosities) of the blends, nanocomposites, and pure components were studied in detail. The strain hardening intensity of different blends and nanocomposites was compared with the behavior of the pure components. Strong strain hardening behavior was observed for blends composed of 50 wt % and higher PBSA content. However, the effect of PBSA content on the elongational viscosity was less pronounced in PLA/PBSA/Clay ternary nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Biodegradable composites of poly(butylene succinate‐co‐butylene adipate) reinforced by poly(lactic acid) fibers

Biodegradable composites of poly(butylene succinate‐co‐butylene adipate) (PBSA) reinforced by poly(lactic acid) (PLA) fibers were developed by hot compression and characterized by Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), dynamic mechanical analyzer, and tensile testing. The results show that PBSA and PLA are immiscible, but their interface can be improved by processing conditions. In particular, their interface and the resulting mechanical properties strongly depend on processing temperature. When the temperature is below 120 °C, the bound between PBSA and PLA fiber is weak, which results in lower tensile modulus and strength. When the processing temperature is higher (greater than 160 °C), the relaxation of polymer chain destroyed the molecular orientation microstructure of the PLA fiber, which results in weakening mechanical properties of the fiber then weakening reinforcement function. Both tensile modulus and strength of the composites increased significantly, in particular for the materials reinforced by long fiber. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43530.     

Synthesis and characterization of poly(butylene terephthalate‐co‐triethylene terephthalate) copolyesters

Poly(butylene terephthalate‐co‐triethylene terephthalate) random copolymers of various compositions and molecular weights were synthesized in bulk and characterized in terms of their chemical structure and thermal and rheological properties. At room temperature all the copolymers were partially crystalline and showed good thermal stability. The main effect of copolymerization was a decrease in the melting and glass‐transition temperatures with respect to the poly(butylene tere‐ phthalate) homopolymer. The fusion temperatures were well correlated with the composition by the Baur equation and the equilibrium melting temperature and the heat of fusion extrapolated values for poly(butylene terephthalate) were in good agreement with those reported elsewhere. Triethylene terephthalate units were found to influence the rheological behavior in the melt, the viscosity being significantly higher than that of the poly(butylene terephthalate‐co‐diethylene terephthalate) copolymers investigated previously. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 981–990, 2001     

Effect of a chain extender on the rheological and mechanical properties of biodegradable poly(lactic acid)/poly[(butylene succinate)‐co‐adipate] blends

Biodegradable polymer blends based on poly(lactic acid) (PLA) and poly[(butylene succinate)‐co‐adipate] (PBSA) were prepared with a laboratory internal mixer. An epoxy‐based, multifunctional chain extender was used to enhance the melt strength of the blends. The morphology of the blends was observed with field emission scanning electron microscopy. The elongational viscosities of the blends, with and without chain extender, were measured with a Sentmanat extensional rheometer universal testing platform. The blends with chain extender exhibited strong strain‐hardening behavior, whereas the blends without chain extender exhibited only weak strain‐hardening behavior. Measurements of the linear viscoelastic properties of the melts suggested that the chain extender promoted the development of chain branching. The results show that PBSA contributed to significant improvements in the ductility of the PLA/PBSA blends, whereas the chain extender did not have a significant effect on the elastic modulus and strain at break of the blends. The combined blending of PLA with PBSA and the incorporation of the chain extender imparted both ductility and melt strength to the system. Thus, such an approach yields a system with enhanced performance and processability. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Compression molding and melt‐spinning of the blends of poly(lactic acid) and poly(butylene succinate‐co‐adipate)

Poly(lactic acid) (PLA) is a biobased polymer made from biomass having high mechanical properties for engineering materials applications. However, PLA has certain limited properties such as its brittleness and low heat distortion temperature. Thus, the aim of this study is to improve toughness of PLA by blending with poly(butylene succinate‐co‐adipate) (PBSA), the biodegradable polymer having high toughness. Polymer blends of PLA and PBSA were prepared using a twin screw extruder. The melt rheology and the thermal property of the blends were examined. Further the blends were fabricated into compression molded parts and melt‐spun fiber and were subjected to tensile and impact tests. When the PBSA content was low, PBSA phase was finely dispersed in the PLA matrix. On the other hand, when the PBSA content was high, this minor phase dispersed as a large droplet. Mechanical properties of the compression molded parts were affected by the dispersion state of PBSA minor component in PLA matrix. Impact strength of the compression molded parts was also improved by the addition of soft PBSA. The improvement was pronounced when the PBSA phase was finely dispersed in PLA matrix. However, the mechanical property of the blend fibers was affected by the postdrawing condition as well as the PBSA content. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41856.     

Poly(butylene succinate‐co‐butylene adipate)/polyethylene oxide blends for controlled release materials: A morphological study

Varying the formulation and processing conditions of polymer blends allows the design of materials with a large range of morphologies. Active materials embedding active compounds in a devoted phase are promising applications of such blends, offering possible various transport properties. In this study, 13 poly(butylene succinate‐co‐butylene adipate) (PBSA)/polyethylene oxide (PEO) blends were extruded in a slit die. Their morphologies were characterized by water extraction (selective PEO dissolution), FTIR spectroscopy, and differential scanning calorimetry. Transport properties were assessed by water vapor permeation and fluorescein release as model migrant. Indeed, the desorption in water of fluorescein (previously entrapped in PEO) was monitored to preliminary investigate the release properties of these materials: two morphologies were obtained (i) pseudo multilayer films made of PEO‐rich layer/PBSA‐rich layer/PEO‐rich layer and (ii) PEO nodules dispersed in the PBSA‐rich matrix for the highest PBSA contents. The first systems were erodible ones with an uncontrolled fast delivery by PEO dissolution whereas the second ones showed a controlled release by permeation through the PBSA matrix from PEO nodules. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42874.     

Morphology,mechanical properties,and thermal stability of poly(L‐lactic acid)/poly(butylene succinate‐co‐adipate)/silicon dioxide composites

Poly(butylene succinate‐co‐adipate) (PBSA) and two types of SiO₂ (hydrophilic or hydrophobic) were used to modify poly(L ‐lactic acid) (PLLA). The mechanical properties, rheological and thermal behavior, phase morphology, and thermal stability of PLLA/PBSA/SiO₂ composites were investigated. The impact strength, flexural strength, and modulus of PLLA/PBSA blends increased after the addition of hydrophobic SiO₂ without decreasing the elongation at break, and the elongation at break monotonically decreased with increasing hydrophilic SiO₂ content. The melt elasticity and viscosity of the PLLA/PBSA blend increased with the addition of SiO₂. The hydrophilic SiO₂ was encapsulated by the dispersed PBSA phase in the composites, which led to the formation of a core–shell structure, whereas the hydrophobic SiO₂ was more uniformly dispersed and mainly located in the PLLA matrix, which was desirable for the optimum reinforcement of the PLLA/PBSA blend. The thermogravimetric analysis results show that the addition of the two types of SiO₂ increased the initial decomposition temperature and activation energy and consequently retarded the thermal degradation of PLLA/PBSA. The retardation of degradation was prominent with the addition of hydrophobic SiO₂. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Aliphatic–aromatic poly(butylene carbonate‐co‐terephthalate) random copolymers: Synthesis,cocrystallization, and composition‐dependent properties

A series of aliphatic–aromatic poly(carbonate‐co‐ester)s poly(butylene carbonate‐co‐terephthalate)s (PBCTs), with weight‐average molecular weight of 113,000 to 146,000 g/mol, were synthesized from dimethyl carbonate, dimethyl terephthalate, and 1,4‐butanediol via a two‐step polycondensation process using tetrabutyl titanate as the catalyst. The PBCTs, being statistically random copolymers, show a single T_g over the entire composition range. The thermal stability of PBCTs strongly depends on the molar composition. Melting temperatures vary from 113 to 213°C for copolymers with butylene terephthalate (BT) unit content higher than 40 mol %. The copolymers have a eutectic melting point when about 10 mol % BT units are included. Crystal lattice structure shifts from the poly(butylene carbonate) to the poly(butylene terephthalate) type crystal phase with increasing BT unit content. DSC and WAXD results indicate that the PBCT copolymers show isodimorphic cocrystallization. The tensile modulus and strength decrease first and then increase according to copolymer composition. The enzymatic degradation of the PBCT copolymers was also studied. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41952.     

Synthesis,cure and pyrolysis behavior of heat‐resistant boron‐silicon hybrid polymer containing acetylene

The synthesis and characterization of a novel heat‐resistant boron‐silicon hybrid polymer containing acetylene (PBSA) and its conversion to a highly crosslinked thermoset were discussed. The polymer was synthesized from phenylboron dichloride using Grignard reagent method. The structure of PBSA was characterized by using Fourier transform infrared spectra, ¹H‐NMR, ¹³C‐NMR, and gel permeation chromatography. PBSA was thermosetting, highly heat‐resistant, high‐viscous, orange liquid at room temperature and good solubility in common organic solvents. Differential scanning calorimetry and thermogravimetric analysis analyses showed that the PBSA had excellent thermal and oxidative stability and the temperature of 5% weight loss (Td₅) were 650 and 638°C under nitrogen and air, respectively, and the residue at 1000°C were 93.3 and 91.3%, respectively, which indicated that the incorporation of boron and silicon into polymeric backbone was found to improve thermal and oxidative properties. X‐ray diffraction and scanning electron microscope were also used to analyze the formation of pyrolytic products. The results showed that the pyrolysis of PBSA resin was made up of β‐SiC and graphite. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical and thermal properties of SEBS‐g‐MA compatibilized halloysite nanotubes reinforced polyethylene terephthalate/polycarbonate/nanocomposites

In this study, the effect of maleic anhydride grafted styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) content on mechanical, thermal, and morphological properties of polyethylene terephthalate/polycarbonate/halloysite nanotubes (PET/PC/HNTs) nanocomposites has been investigated. Nanocomposites of PET/PC (70 : 30) with 2 phr of HNTs were compounded using the counter rotating twin screw extruder. A series of formulations were prepared by adding 5–20 phr SEBS‐g‐MA to the composites. Incorporation of 5 phr SEBS‐g‐MA into the nanocomposites resulted in the highest tensile and flexural strength. Maximum improvement in the impact strength which is 245% was achieved at 10 phr SEBS‐g‐MA content. The elongation at break increased proportionately with the SEBS‐g‐MA content. However, the tensile and flexural moduli decreased with increasing SEBS‐g‐MA content. Scanning electron microscopy revealed a transition from a brittle fracture to ductile fracture morphology with increasing amount of SEBS‐g‐MA. Transmission electron microscopy showed that the addition of SEBS‐g‐MA into the nanocomposites promoted a better dispersion of HNTs in the matrix. A single glass transition temperature was observed from the differential scanning calorimetry test for compatibilized nanocomposites. Thermogravimetric analysis of PET/PC/HNTs nanocomposites showed high thermal stability at 15 phr SEBS‐g‐MA content. However, on further addition of SEBS‐g‐MA up to 20 phr, thermal stability of the nanocomposites decreased due to the excess amount of SEBS‐g‐MA. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42608.     

Catalyzed chain extension of poly(butylene adipate) and poly(butylene succinate) with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline)

Low‐molecular‐weight HOOC‐terminated poly(butylene adipate) prepolymer (PrePBA) and poly(butylene succinate) prepolymer (PrePBS) were synthesized through melt‐condensation polymerization from adipic acid or succinic acid with butanediol. The catalyzed chain extension of these prepolymers was carried out at 180–220°C with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) as a chain extender and p‐toluenesulfonic acid (p‐TSA) as a catalyst. Higher molecular weight polyesters were obtained from the catalyzed chain extension than from the noncatalyzed one. However, an improperly high amount of p‐TSA and a high temperature caused branching or a crosslinking reaction. Under optimal conditions, chain‐extended poly(butylene adipate) (PBA) with a number‐average molecular weight up to 29,600 and poly(butylene succinate) (PBS) with an intrinsic viscosity of 0.82 dL/g were synthesized. The chain‐extended polyesters were characterized by IR spectroscopy, ¹H‐NMR spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray scattering, and tensile testing. DSC, wide‐angle X‐ray scattering, and thermogravimetric analysis characterization showed that the chain‐extended PBA and PBS had lower melting temperatures and crystallinities and slower crystallization rates and were less thermally stable than PrePBA and PrePBS. This deterioration of their properties was not harmful enough to impair their thermal processing properties and should not prevent them from being used as biodegradable thermoplastics. The tensile strength of the chain‐extended PBS was about 31.05 MPa. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis of click‐coupled graphene sheets with hyperbranched polyurethane: Effective exfoliation and enhancement of nanocomposite properties

Graphene oxide (GO) was functionalized with hyperbranched polyurethane (HBPU) via click coupling between azide‐functionalized HBPU and alkynyl‐decorated GO. HBPU‐functionalized GO composites of various compositions were prepared. The azide‐containing HBPU was characterized using Fourier‐transform infrared (FT‐IR) spectroscopy and ¹H‐nuclear magnetic resonance spectroscopy. The HBPU‐functionalized GO composites were characterized using transmission electron microscopy and FT‐IR spectroscopy. The functionalized GO showed excellent dispersion in the HBPU matrix, giving composites with enhanced mechanical and thermal properties. The material properties were effectively regulated by click‐coupled exfoliation of GO with HBPU, enabling the production of high‐performance materials. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44631.     

Effect of Organoclay on the Morphology and Properties of Poly(propylene)/Poly[(butylene succinate)‐co‐adipate] Blends

The effect of organically modified clay on the morphology and properties of poly(propylene) (PP) and poly[(butylene succinate)‐co‐adipate] (PBSA) blends is studied. Virgin and organoclay modified blends were prepared by melt‐mixing of PP, PBSA and organoclay in a batch‐mixer at 190 °C. Scanning electron microscopy studies revealed a significant change in morphology of PP/PBSA blend in the presence of organoclay. The state of dispersion of silicate layers in the blend matrix was characterized by X‐ray diffraction and transmission electron microscopic observations. Dynamic mechanical analysis showed substantial improvement in flexural storage modulus of organoclay‐modified blends with respect to the neat polymer matrices or unmodified blends. Tensile properties of virgin blends also improved in the presence of organoclay. Thermal stability of virgin blends in air atmosphere dramatically improved after modification with organoclay. The effect of organoclay on the melt‐state liner viscoelastic properties of virgin blends was also studied. The non‐isothermal crystallization behavior of homopolymers, virgin, and organoclay‐modified blends were studied by differential scanning calorimeter. The effect of incorporation of organoclay on the cold crystallization behavior of PP/PBSA blends is also reported.

     

In the melt,grafting of polycarbonate onto polystyrene‐block‐poly(ethylene‐butylene)‐block‐polystyrene‐grafted‐maleic anhydride: Reactive extrusion

The use of reactions between polycarbonate (PC) and polystyrene‐block‐poly(ethylene‐butylene)‐block‐polystyrene‐ grafted‐maleic anhydride (SEBS‐g‐MAH) is a convenient way to create SEBS‐g‐PC. Grafting was realized by reactive extrusion at three temperatures using SnOct₂ or TBD catalysts. SEC analyses showed the apparition of a double distribution when the TBD was used. The mean residence time widely increased when this catalyst was used, and the rheological curves depicted a percolation effect of the SEBS nodules in the PC matrix. No explicit evolution was found with the use of SnOct₂. The thermal analyses showed the disappearance of the PC phase transition temperature. The Van Gurp‐Palmen plots confirmed the efficiency of the TBD catalyst and that 260°C was the optimal reactive extrusion temperature. POLYM. ENG. SCI., 54:2660–2668, 2014. © 2013 Society of Plastics Engineers     

Thermal and mechanical properties of liquid silicone rubber composites filled with functionalized graphene oxide

To improve the thermal and mechanical properties of liquid silicone rubber (LSR) for application, the graphene oxide (GO) was proposed to reinforce the LSR. The GO was functionalized with triethoxyvinylsilane (TEVS) by dehydration reaction to improve the dispersion and compatibility in the matrix. The structure of the functionalized graphene oxide (TEVS‐GO) was evaluated by Thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectra, X‐ray diffraction (XRD), and energy dispersive X‐ray spectroscopy (EDX). It was found that the TEVS was successfully grafted on the surface of GO. The TEVS‐GO/LSR composites were prepared via in situ polymerization. The structure of the composites was verified by FTIR, XRD, and scanning electron microscopy (SEM). The thermal properties of the composites were characterized by TGA and thermal conductivity. The results showed that the 10% weight loss temperature (T₁₀) increased 16.0°C with only 0.3 wt % addition of TEVS‐GO and the thermal conductivity possessed a two‐fold increase, compared to the pure LSR. Furthermore, the mechanical properties were studied and results revealed that the TEVS‐GO/LSR composites with 0.3 wt % TEVS‐GO displayed a 2.3‐fold increase in tensile strength, a 2.79‐fold enhancement in tear strength, and a 1.97‐fold reinforcement in shear strength compared with the neat LSR. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42582.     

In situ polymerized nanocomposites of poly(butylene succinate)/Tio2 nanofibers: molecular weight,morphology, and thermal properties

In this study, the nanocomposites of poly(butylene succinate) (PBS) and TiO₂ nanofibers were first synthesized via in situ polymerization. Molecular weight, morphology, and thermal properties of the nanocomposites were characterized. As the weight percentage of TiO₂ nanofibers increased from 0 to 2%, the molecular weight of PBS in the nanocomposites decreased gradually compared with that of pure PBS. In morphology, the nanocomposites were constituted by free PBS and PBS‐grafted TiO₂ nanofibers (PBS‐g‐TiO₂), which were proved by the Fourier transform infrared, scanning electron microscopy (SEM), and transmission electron microscopy. In addition, the SEM demonstrated the strong interfacial interaction and homogeneous distribution between TiO₂ nanofibers and PBS matrix. The thermal properties determined by differential scanning calorimetry and thermogravimetric analysis included the increasing of cold crystallization temperatures, the melting temperatures, and the thermal stability. Besides, the crystallinity and the rate of crystallization of the nanocomposites were enhanced, which were also observed by the X‐ray diffraction. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013