Morphology and properties of poly(vinylidene fluoride)/silicone rubber blends

Blends of poly(vinylidene fluoride) (PVDF) and silicone rubber (SR) were prepared through melt mixing. The morphology, rheology, crystallization behavior, mechanical properties, dynamic mechanical properties and thermal properties of the PVDF/SR blends were investigated. The blend with 9 wt % of SR showed spherical shape of disperse phase whereas the blend with 27 wt % of SR resulted in irregular shape of rubber phase. The rheology showed that the complex viscosity and storage modulus of the blends decreased with increasing the SR content. The mechanical properties of the blends were decreased with increasing the SR content but that were significantly improved after dynamical vulcanization. The crystallization temperature of PVDF phase in PVDF/SR blends was increased. The incorporation of SR improved the thermal stability of PVDF/SR blends, and the temperature at 10% mass loss of the blends increased to about 489°C compared with 478°C of the pure PVDF. The mass of residual char in experiment of the blends was lower than that obtained in theory. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39945.     

Evolution of morphology,ferroelectric, and mechanical properties in poly(vinylidene fluoride)–poly(vinylidene fluoride‐trifluoroethylene) blends

Considering the complementary properties of poly(vinylidene fluoride) (PVDF) and poly(vinylidene fluoride‐trifluoroethylene) [P(VDF‐TrFE)], it appears that their blends have the potential to be promising candidates for device applications. We report the evolution of morphology, ferroelectric, and mechanical properties (modulus and hardness) and their dependence on preparation temperature for PVDF–P(VDF‐TrFE) blends. From ferroelectric hysteresis measurements it was found that P(VDF‐TrFE) rich blends treated at higher temperature show significant values of remanent polarization. Remanent polarization values show a fourfold increase in these P(VDF‐TrFE) rich blends treated at higher temperature. Interestingly, blends prepared from high temperature showed greater value of remanent polarization even though they were found to consist of smaller amount of electroactive phase as compared to their low temperature treated counterpart. Nanoindentation experiments revealed that high temperature treatment improves the modulus of blends by at least 100%. This report attempts to tie these findings to the morphology and crystallinity of these blends. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45955.     

Miscibility and morphology of poly(vinylidene fluoride)/poly[(vinylidene fluoride)‐ran‐trifluorethylene] blends

This study presents an investigation of the effect of the different crystalline phases of each blend component on miscibility when blending poly(vinylidene fluoride) (PVDF) and its copolymer poly[(vinylidene fluoride)‐ran‐trifluorethylene] [P(VDF–TrFE)] containing 72 mol % of VDF. It was found that, when both components crystallized in their ferroelectric phase, the PVDF showed a strong effect on the crystallinity and phase‐transition temperature of the copolymer, indicating partial miscibility in the crystalline state. On the other hand, immiscibility was observed when both components, after melting, were crystallized in their paraelectric phase. In this case, however, a decrease in crystallization temperatures suggested a strong interaction between monomers in the liquid state. Blend morphologies indicated that, in spite of the lack of miscibility in the crystalline state, there is at least miscibility between PVDF and P(VDF–TrFE) in the liquid state, and that a very intimate mixture of the two phases on the lamellar level can be maintained upon crystallization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1362–1369, 2002     

Dynamic rheological behavior and morphology of poly(trimethylene terephthalate)/poly(ethylene octene) copolymer blends

The dynamic rheology and morphology of poly(trimethylene terephthalate) and maleic anhydride grafted poly(ethylene octene) composites were investigated. A specific viscoelastic phenomenon, that is, a second plateau, appeared at low frequencies and exhibited a certain dependence on the content of elastomer particles and the temperature. This phenomenon was attributed to the formation of an aggregation structure of rubber particles. The analyses of the dynamic viscoelastic functions suggested that the heterogeneity of the composites was enhanced as the particle content or temperature increased. The microstructural observation by scanning electron microscopy confirmed that maleic anhydride could react with the end groups of poly(trimethylene terephthalate) to form a stable interfacial layer and result in a smaller dispersed‐phase particle size due to the reduced interface tension. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Nanophase morphology and crystallization in poly(vinylidene fluoride)/polydimethylsiloxane‐block‐poly(methyl methacrylate) blends

A polydimethylsiloxane‐block‐poly(methyl methacrylate) (PDMS‐b‐PMMA) diblock copolymer was synthesized by the atom transfer radical polymerization method and blended with a high‐molecular‐weight poly(vinylidene fluoride) (PVDF). In this A‐b‐B/C type of diblock copolymer/homopolymer system, semi‐crystallizable PVDF (C) and PMMA (B) block are miscible due to favorable intermolecular interactions. However, the A block (PDMS) is immiscible with PVDF and therefore generates nanostructured morphology via self‐assembly. Crystallization study reveals that both α and γ crystalline phases of PVDF are present in the blends with up to 30 wt% of PDMS‐b‐PMMA block copolymer. Adding 10 wt% of PVDF to PDMS‐b‐PMMA diblock copolymer leads to worm‐like micelle morphology of PDMS of 10 nm in diameter and tens of nanometers in length. Moreover, morphological results show that PDMS nanostructures are localized in the inter‐fibrillar region of PVDF with the addition of up to 20 wt% of the block copolymer. Increase of PVDF long period by 45% and decrease of degree of crystallization by 34% confirm the localization of PDMS in the PVDF inter‐fibrillar region. © 2018 Society of Chemical Industry     

Feather‐like morphology of poly(methyl methacrylate)/poly(ethylene oxide) blends: The effect of cooling rate and poly(methyl methacrylate) content

The effect of cooling rate on the crystallization morphology and growth rate of poly(ethylene oxide) (PEO) and PEO/poly(methyl methacrylate) (PMMA) blends has been observed by Hot Stage Polarized Microscopy (HS‐POM). The isothermal crystallization kinetics study was carried out by differential scanning calorimetry (DSC). The spherulite morphology has been observed for the neat PEO with molecular weight of 6000 g/mol. By adding of PMMA with molecular weight of 39,300 g/mol, the growth fronts become irregular. With the increasing of PMMA content, the irregularity of growth front becomes more obvious, and the feather‐like morphology can be observed. When PMMA content is 60%, the spherulite is seriously destroyed. This phenomenon is more obvious for the slow cooling process. Based on the measurement of spherulite, the growth rate curves were obtained. According to the curves, it can be seen that the growth rate decreases with the increasing of PMMA content, and the growth rate during the slow cooling process is higher than that of the fast cooling process. The isothermal crystallization experiment indicates that the crystallization rate decreases dramatically with the increasing of PMMA content. And the Avrami parameter n was obtained, which is non‐integral and less than 3. Finally, it can be concluded that the higher value of n can be obtained for the condition with low crystallization rate. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41705.     

Spherulitic morphology and growth of poly(vinylidene fluoride)/poly(3-hydroxybutyrate-co-hydroxyvalerate) blends by optical microscopy

Poly(vinylidene fluoride) (PVDF) and poly(3-hydroxybutyrate-co-hydroxyvalerate) (PHBV), both semicrystalline polymers, are miscible as shown by the single glass transition temperature over the entire composition range. Morphology of PVDF/PHBV blends was investigated by optical microscopy under two different crystallization conditions. PVDF showed the spherulitic morphology at 150 °C in the PVDF/PHBV blends, where PHBV acted as the noncrystallizing component. PHBV also showed the spherulitic morphology within the matrix of the pre-existing PVDF crystals when PVDF/PHBV blends were quenched from the melt to the crystallization temperature below the melting point of PHBV. The spherulitic growth of PHBV was investigated as the function of both blend composition and crystallization temperature.     

Morphological and infra-red studies on highly oriented poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Highly oriented melt drawn films of poly(vinylidene fluoride) (PVDF) and blends of poly(vinylidene fluoride) and poly(methyl methacrylate) (PMMA) have been studied by transmission electron microscopy, electron diffraction and infra-red spectroscopy. Infra-red spectra show the second moment of the orientation function for PVDF samples to be greater than 0.94. Using such a sample, the transition dipole directions relative to the chain axis have been calculated. Electron microscopic studies of the PVDF/PMMA blends show a transformation for pure PVDF from a lamellar morphology to a mixture of lamellar and needle-like crystals for the 80/20 blend. The 60/40 blend shows a pure needle-like morphology. The β phase content for this blend is dependent upon the composition and thermal history. An increase in the β phase content is observed with the addition of PMMA. After annealing at 110°C, the 50/50 blend shows a lamellar β phase morphology. A significant increase in the segmental orientation of PVDF is also observed.     

The crystallization morphology evolution of polyoxymethylene/poly(ethylene oxide) blend micropart prepared under microinjection molding conditions

This article is the first study on the microinjection molding and the effects of the microprocessing parameters on the crystallization and orientation of polyoxymethylene/poly(ethylene oxide) (POM/PEO) blend, which has better toughness and self‐lubricity compared with the neat POM and therefore is a better candidate material for making microparts like microgears with higher performances. The crystalline and phase morphologies were investigated by polarized light microscope (PLM), differential scanning calorimeter (DSC) and scanning electron microscope (SEM). The crystalline orientation of the microparts was evaluated by two‐dimensional wide‐angle X‐ray diffraction (2D‐WAXD) and Herman's orientation function. The experimental results showed that both POM and POM/PEO microparts prepared by microinjection molding exhibited three distinct layers, i.e., skin layer, shear layer and core layer, while the latter had thicker shear layer but thinner skin layer and core layer. PEO was well dispersed in POM matrix. The spherulite size, the melting point as well as the crystallinity of POM in the POM/PEO blend decreased due to the interference of PEO in the crystallization of POM. A shish‐kebab structure was observed in the shear layers of the POM/PEO microparts. The effects of processing parameters on the thicknesses of different layers of the POM/PEO microparts were investigated. With increase of the injection speed or decrease of the mold temperature, the skin layer and the core layer became thicker, while the shear layer and the oriented region became thinner. However, the influence of the injection pressure was not obvious. Also, the processing parameters affected the crystalline orientation of the POM/PEO microparts. With increase of the injection speed or decrease of the mold temperature, the orientation function f decreased, indicating a lower degree of orientation. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40538.     

Nanophase morphology and crystallization in poly(vinylidene fluoride)/polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene blends

An approach to achieve confined crystallization of ferroelectric semicrystalline poly(vinylidene fluoride) (PVDF) was investigated. A novel polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene (PDMS‐b‐PMMA‐b‐PS) triblock copolymer was synthesized by the atom‐transfer radical polymerization method and blended with PVDF. Miscibility, crystallization and morphology of the PVDF/PDMS‐b‐PMMA‐b‐PS blends were studied within the whole range of concentration. In this A‐b‐B‐b‐C/D type of triblock copolymer/homopolymer system, crystallizable PVDF (D) and PMMA (B) middle block are miscible because of specific intermolecular interactions while A block (PDMS) and C block (PS) are immiscible with PVDF. Nanostructured morphology is formed via self‐assembly, displaying a variety of phase structures and semicrystalline morphologies. Crystallization at 145 °C reveals that both α and β crystalline phases of PVDF are present in PVDF/PDMS‐b‐PMMA‐b‐PS blends. Incorporation of the triblock copolymer decreases the degree of crystallization and enhances the proportion of β to α phase of semicrystalline PVDF. Introduction of PDMS‐b‐PMMA‐b‐PS triblock copolymer to PVDF makes the crystalline structures compact and confines the crystal size. Moreover, small‐angle X‐ray scattering results indicate that the immiscible PDMS as a soft block and PS as a hard block are localized in PVDF crystalline structures. © 2019 Society of Chemical Industry     

Crystallization of poly(ethylene oxide) in i-polypropylene–poly(ethylene oxide) blends

A two-stage stable system of isotactic polypropylene–poly(ethylene oxide) blend, in which poly(ethylene oxide) can be permanent either in molten or in crystallized states in the temperature range from 280 to 327 K, was described. The behavior of that blend was explained in terms of fractionated crystallization. A fine dispersion of poly(ethylene oxide) inclusions is required for efficient suppression of crystallization initiated by heterogeneous nuclei. The application of a thin film of polypropylene-poly(ethylene oxide) 9 : 1 blend obtained by quenching for multiuse erasable and rewritable carriers for visible information has been demonstrated. The same sample exhibits different dynamic mechanical properties when poly(ethylene oxide) inclusions are molten or crystallized. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2047–2057, 1997     

Melt rheology and mechanical crystal transformation in an immiscible blend with poly(vinylidene fluoride) matrix

Effect of immiscible polyamide 6 (PA6) on the melt rheology and stretch‐induced crystal transformation of poly (vinylidene fluoride) (PVDF) matrix is reported. PA6 is dispersed as submicron droplets in the PVDF matrix, responsible for significant enhancement in the melt elasticity. Nevertheless, crystallization habits of PVDF matrix from melt are little affected by submicron PA6 droplets, and the α‐form of PVDF prevails in the blends. Upon mechanical stretching, the α‐form is converted to the β‐form, which is remarkably reduced with the increasing of PA6 content in the blends. It could be correlated with the decreased tensile stress in the presence of submicron PA6 droplets that act as stress concentrators. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43499.     

The crystalline morphology of poly(vinylidene fluoride)/poly(methylmethacrylate) blends

Poly(vinylidene fluoride), PVF₂, as well as blends of PVF₂ with poly(methyl methacrylate), PMMA, develop a variety of crystalline morphologies at low undercoolings. Both the α and γ crystal forms grow from the melt and the former undergoes a solid-solid phase transition to the latter, though its morphology remains unaltered. Three melting temperatures which decrease with increasing PMMA content are observed. Hoffman-Weeks analysis shows the equilibrium melting points of the blends to be depressed. Using these equilibrium values, the thermodynamic interaction energy density is calculated to go from ?5.40 × 10⁶ to ?2.96 × 10⁷ j/m³ as the blend composition goes from 40.1 volume percent to pure PVF₂. The band periodicity in the α form spherulites increases with crystallization temperature and PMMA content and it appears to be from a lamellar reorientation process with an apparent activation energy of 322 cal/mole. Electron diffraction patterns taken along the radial direction in a given spherulite reveal lamellar twisting which causes the banded appearance. Light scattering results suggest that the lamellar are formed into rod-like structures on a local scale but that on a larger scale they develop a disoriented spherulitic morphology.     

Multiple melting in blends of poly(vinylidene fluoride) with isotactic poly(ethyl methacrylate)

Multiple melting phenomena have been studied in blends of poly(vinylidene fluoride) (PVF₂) with low molar mass isotactic poly(ethyl methacrylate) (it-PEMA). In all blends, as well as in pure PVF₂, a transition (T₁) was observed prior to the main melting point (T₂). T₁ is probably connected with the melting of secondarily-crystallized material. In addition to this, a high temperature melting endotherm (T₃) was observed, which could be ascribed completely to recrystallization of PVF₂. The highest transition (T₄) was caused by melting of the σ form of PVF₂. From Hoffman-Weeks plots—T₂ vs. crystallization temperature, T_c — it could be concluded that no thermody amic depression of the melting point of PVF₂ occurred in the blends. The stabilities of PVF₂ crystallites in the various blends were derived from the slopes of Hoffman-Weeks plots and were in good agreement with lamellar thicknesses found from SAXS measurements.     

Form birefringence and turbidity of polystyrene/poly(methyl methacrylate) blends in slit dies and planar contractions

The birefringence and turbidity of a polystyrene/poly(methyl methacrylate) (PMMA) blend, with the concentration of the PMMA dispersed phase ranging up to 1%, were measured in both a slit channel with a constant cross section and a planar hyperbolic contraction/expansion (8:1:8). The measurements were performed by the attachment of a modular rheo‐optical die to a twin‐screw extruder. The optical arrangement had a red light‐emitting diode as the source and two photoresistors, with one of them measuring the turbidity and the other one measuring the transmitted intensity between cross‐polarizers. The experimental procedure consisted of the stopping of the extruder feeding, while the screw rotation was kept constant. Because the form birefringence could be associated with the shape of the droplets, these measurements were used to infer information about the PMMA droplet deformation and breakup. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44066.     

Crystallization of poly(tetramethylene succinate) in blends with poly(ϵ‐caprolactone) and poly(ethylene terephthalate)

The crystallization behavior of polymer blends of poly(tetramethylene succinate) (PTMS) with poly(?‐caprolactone) (PCL) or poly(ethylene terephthalate) (PET) was investigated with differential scanning calorimetry under isothermal and nonisothermal conditions. The blends were prepared by solution casting and precipitation, respectively. The constituent polymers were semicrystalline materials and crystallized nearly independently in the blends. The addition of the second component to PTMS showed that PCL did not significantly influence the crystallinity of the constituents in the blends under isothermal conditions, whereas the crystallization of PTMS was slightly suppressed by crystalline PET. Nonisothermal crystallization under constant cooling rates was examined in terms of a quasi‐isothermal Avrami approach. In blends, the rates of crystallization were differently influenced by the second component. The rate of the constituent that crystallized at the higher temperature was barely influenced by the second component being in the molten state, whereas the rate of the second component, crystallizing when the first component was already crystalline, was altered differently under isothermal and nonisothermal conditions. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 149–160, 2004     

Effects of compatibilizer on the mechanical,rheological, and shape memory behaviors of poly(lactic acid) and poly(MnBM) blends

The effects of compatibilizer on the morphological, mechanical, rheological, and shape memory properties of poly(lactic acid) (PLA) and poly(methyl methacrylate-block-n-butyl acrylate-block-methyl methacrylate) (Poly(MnBM)) (80/20) blend were investigated. From the morphological results, the addition of 1 wt% SAN-MAH as a compatibilizer showed minimum Poly(MnBM) domain size among the blends with the SAN-MAH in the amounts from 0 to 7 wt%. Tensile and flexural strengths, and complex viscosity of the blends showed maximum when the SAN-MAH content was 1 wt%, which suggested the increased compatibility between the PLA and Poly(MnBM) phases. From the above results, the optimum compatibilizer content of the PLA and Poly(MnBM) blend was 1 wt%. The recovery ratio of tensile energy was found to be 83 and 56% for the PLA/Poly(MnBM) blend with and without the SAN-MAH (1 wt%), respectively. Upon blending the PLA and Poly(MnBM) (80/20) with SAN-MAH (1 wt%), the increase of recovered tensile energy was observed, and that the brittleness of PLA was improved to be ductile which resulted an improved shape memory behavior of the blend. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48591.     

Study of morphology influence on rheological properties of compatibilized TPU/SAN blends

The compatibilizing efficiency of three different compatibilizers on the thermoplastic polyurethane/styrene‐co‐acrylonitrile (TPU/SAN) blends properties was investigated after compatibilizer's incorporation via melt‐mixing. The compatibilizers studied were as follows: poly‐ε‐caprolactone (PCL) of different molecular weight (M_w), a mixture of polystyrene‐block‐polycaprolactone (PS‐b‐PCL) and polystyrene‐block‐poly (methyl methacrylate) (PS‐b‐PMMA), and a mixture of polyisoprene‐block‐polycaprolactone (PI‐b‐PCL) and polybutadiene‐block‐poly (methyl methacrylate) (PB‐b‐PMMA). In our study, the effect of 5 wt % added compatibilizers on TPU/SAN blends morphology was examined. The transmission electron microscopy (TEM) was used to study the morphology at different length scales and to determine the compatibilizer's location. Investigations showed the different improvement of properties, because of the different incorporation of compatibilizers in the polymer blend. The morphology influence on the rheological behavior of compatibilized blends was investigated with a stress‐controlled rheometer (Rheometric Dynamic Stress Rheometer, SR‐500). Different compatibilization activity was found for different system. It was also found that compatibilization activity of added compatibilizer strongly depends on the comaptibilizer's M_w. Blends compatibilized with PCL showed superior properties as compared with the other examined blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2303–2316, 2006     

Piezo- and pyroelectricity in polymer blends of poly(vinylidene fluoride)/poly(methyl methacrylate)

Compatible polymer blends of poly(vinylidene fluoride) (PVDF) and poly(methyl methacrylate) (PMMA) can be used as suitable model systems for investigating the relationship between the physico-chemical structure of polymers and their piezo- and pyroelectric activity. The structure of PVDF/PMMA blends can be varied over a very wide range which can lead to a strong influence on the piezo- and pyroelectric activity and the corresponding coefficients d₃₁ and g₃. The values of d₃₁ and g₃ were found to vary over nearly five decades whereas the normalized coefficients $\text{d}{}_{31}\text{P}$ and $\text{g}{}_3\text{P}$ remain largely unaffected. This emphasizes the importance of the molecular processes causing the macroscopic polarization P during the poling procedure. For a given polarization P and a given temperature T the properties of the polymer matrix, however, are far less important for the values obtained for d₃₁ and g₃. The experimental results were compared with theoretical predictions based on models which were recently developed by Tashiro et al., Broadhurst et al. and by Mopsik et al.. Considering the appropriate scope of each model a good agreement between theory and experiment is observed and general contradictions have not been found.     

Morphology and barrier mechanism of biaxially oriented poly(ethylene terephthalate)/poly(ethylene 2,6‐naphthalate) blends

To improve the barrier properties of poly(ethylene terephthalate) (PET), PET/poly(ethylene 2,6‐naphthalate) (PEN) blends with different concentrations of PEN were prepared and were then processed into biaxially oriented PET/PEN films. The air permeability of bioriented films of pure PET, pure PEN, and PET/PEN blends were tested by the differential pressure method. The morphology of the blends was studied by scanning electron microscopy (SEM) observation of the impact fracture surfaces of extruded PET/PEN samples, and the morphology of the films was also investigated by SEM. The results of the study indicated that PEN could effectively improve the barrier properties of PET, and the barrier properties of the PET/PEN blends improved with increasing PEN concentration. When the PEN concentration was equal to or less than 30%, as in this study, the PET/PEN blends were phase‐separated; that is, PET formed the continuous phase, whereas PEN formed a dispersed phase of particles, and the interface was firmly integrated because of transesterification. After the PET/PEN blends were bioriented, the PET matrix contained a PEN microstructure consisting of parallel and extended, separate layers. This multilayer microstructure was characterized by microcontinuity, which resulted in improved barrier properties because air permeation was delayed as the air had to detour around the PEN layer structure. At a constant PEN concentration, the more extended the PEN layers were, the better the barrier properties were of the PET/PEN blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1309–1316, 2006