Thermomechanical properties and shape memory effect of epoxidized natural rubber crosslinked by 3‐amino‐1,2,4‐triazole

A thermally induced shape memory polymer based on epoxidized natural rubber (ENR) was produced by curing the ENR with 3‐amino‐1,2,4‐triazole as a crosslinker in the presence of bisphenol‐A as a catalyst. Dynamic mechanical and tensile analysis was conducted to examine the variation of glass transition temperature, stiffness, and extensibility of the vulcanizates with the amount of curatives. Shape memory properties of the ENR vulcanizates were characterized by shape retention and shape recovery. It was revealed that the glass transition temperature of the ENR vulcanizates could be tuned well above room temperature by increasing the amount of curing agents. Also, ENR vulcanizates with T_g higher than ambient temperature showed good shape memory effects under 100% elongation, and the response temperatures of the recovery were well matched with T_g of the samples. Copyright © 2006 Society of Chemical Industry     

Glass transition and mechanical properties of PLLA and PDLLA‐PGA copolymer blends

The change of the glass transition temperatures (T_g) in the blend of poly(L ‐lactic acid) (PLLA) and the copolymers of poly(D,L ‐lactic acid) and poly(glycolic acid) (PDLLA‐PGA) with different D,L ‐lactic acid and glycolic acid composition ratio (50 : 50, 65 : 35, and 75 : 25) was studied by DSC. Dynamic mechanical measurement and tensile testing were performed at various temperatures around T_g of the blend. In the blend of PLLA and PDLLA‐PGA50 (composition ratio of PDLLA and PGA 50 : 50), T_g decreased from that of PLLA (about 58°C) to that of PDLLA‐PGA50 (about 30°C). A single step decrease was observed in the DSC curve around T_g between the weight fraction of PLLA (W(PLLA)) 1.0 and 0.7 (about 52°C) but two‐step changes in the curve are observed between W(PLLA) = 0.6 and 0.3. The T_g change between that of PLLA and that of PDLLA‐PGA and the appearance of two T_gs suggest the existence of PLLA rich amorphous region and PDLLA‐PGA copolymer rich amorphous region in the blend. A single step decrease of E′ occurs at around T_g of the pure PLLA but the two‐step decrease was observed at W(PLLA) = 0.6 and 0.4, supporting the existence of the PLLA rich region and PDLLA‐PGA rich region. Tensile testing for various blends at elevated temperature showed that the extension without yielding occurred above T_g of the blend. Partial miscibility is suggested for PLLA and PDLLA‐PGA copolymer blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2164–2173, 2004     

Thermal,mechanical, and shape‐memory properties of nanorubber‐toughened,epoxy‐based shape‐memory nanocomposites

Epoxy‐based shape‐memory polymers (ESMPs) are a type of the most promising engineering smart polymers. However, their inherent brittleness limits their applications. Existing modification approaches are either based on complicated chemical reactions or done at the cost of the thermal properties of the ESMPs. In this study, a simple approach was used to fabricate ESMPs with the aim of improving their overall properties by introducing crosslinked carboxylic nitrile–butadiene nanorubber (CNBNR) into the ESMP network. The results show that the toughness of the CNBNR–ESMP nanocomposites greatly improved at both room temperature and the glass‐transition temperature (T_g) over that of the pure ESMP. Meanwhile, the increase in the toughness did not negatively affect other macroscopic properties. The CNBNR–ESMP nanocomposites presented improved thermal properties with a T_g in a stable range around 100 °C, enhanced thermal stabilities, and superior shape‐memory performance in terms of the shape‐fixing ratio, shape‐recovery ratio, shape‐recovery time, and repeatability of shape‐memory cycles. The combined property improvements and the simplicity of the manufacturing process demonstrated that the CNBNR–ESMP nanocomposites are desirable candidates for large‐scale applications in the engineering field as smart structural materials. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45780.     

Stretch‐induced molecular ordering in amorphous/crystalline polylactide blends

The effect of amorphous poly(D ,L ‐lactide) (PDLLA) on the molecular orientation and crystallization of crystalline poly(L ‐lactide) (PLLA) on stretching is reported in this study. It is indicated that the presence of PDLLA in its miscible blends with PLLA is not favorable for either cohesive mesophase formation below T_g or strain‐induced crystallization above T_g at strains beyond the segmental extensibility limit. Because of lack of constraints imposed by cohesive mesophase or crystals, oriented segments are liable to slide each other or recoil, responsible for low‐molecular orientation in the stretched blends. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Dynamic mechanical and shape memory properties of copolymers based on o‐allylphenol type benzoxazines and diglycidyl ether of bisphenol‐A

Three benzoxazines based on o‐allylphenol and 1,6‐hexamethylenediamine (HDA) or 4,4′‐diaminodiphenyl methane (DDM) or 4,4′‐diaminodiphenyl ether (DDE) were respectively blended with diglycidyl ether of bisphenol‐A (DGEBA) in various weight ratios followed by thermal polymerization to prepare three series of benzoxazine/DGEBA copolymers. With increasing DGEBA content, the peak temperature of the exothermic peaks in the DSC curves shows a systematic increase for the three series of benzoxazine/DGEBA blends. Each copolymer shows a single glass transition temperature (T_g). As the content of DGEBA is increased, T_g reaches a minimum for the copolymer system based on HDA but a maximum for the two systems based on DDM and DDE. For the same benzoxazine/DGEBA weight ratio, copolymers based on DDM and DDE show high T_g values over those based on HDA. The three series of benzoxazine/DGEBA copolymers exhibit a one‐way dual shape memory effect based on T_g, and the shape memory properties of the copolymers under tensile deformation mode vary with the variation of both diamine bridge structure and DGEBA content. © 2018 Society of Chemical Industry     

Influences of phase composition and thermomechanical conditions on shape memory properties of segmented polyurethanes with amorphous reversible phase

We synthesized series of shape memory polyurethanes with amorphous reversible phase (T_g‐SMPUs) and systematically studied their microphase structure and shape memory properties. The T_g‐SMPUs having no or less hard phase showed lower shape recovery. When the volume fraction of hard phase was in the range of 20–30%, the T_g‐SMPUs exhibited the highest shape recovery. As the fraction of hard phase increased further the shape recovery decreased, because more polymer components with higher glass transition temperatures (T_gs) would participate in strain storage. For the T_g‐SMPUs having similar T_gs, those polymers having higher volume fraction of hard phase exhibited higher shape fixity, broader shape recovery region, and larger recovery stress. Increasing deformation strain could raise shape fixity and recovery stress but broaden shape recovery region. The highest recovery stress of a material could be achieved when the deformation occurred at its glass transition temperature below which decreasing deformation temperature could not increase recovery stress further. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Silicone membranes to inhibit water uptake into thermoset polyurethane shape‐memory polymer conductive composites

Electroactive shape memory polymer (SMP) composites capable of shape actuation via resistive heating are of interest for various biomedical applications. However, water uptake into SMPs will produce a depression of the glass transition temperature (T_g) resulting in shape recovery in vivo. While water actuated shape recovery may be useful, it is foreseen to be undesirable during early periods of surgical placement into the body. Silicone membranes have been previously reported to prevent release of conductive filler from an electroactive polymer composite in vivo. In this study, a silicone membrane was used to inhibit water uptake into a thermoset SMP composite containing conductive filler. Thermoset polyurethane SMPs were loaded with either 5 wt % carbon black or 5 wt % carbon nanotubes, and subsequently coated with either an Al₂O₃‐ or silica‐filled silicone membrane. It was observed that the silicone membranes, particularly the silica‐filled membrane, reduced the rate of water absorption (37°C) and subsequent T_g depression versus uncoated composites. In turn, this led to a reduction in the rate of recovery of the permanent shape when exposed to water at 37°C. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41226.     

Synthesis and properties of ethylene‐substituted styrene copolymers

The copolymerization of ethylene and substituted styrenes [RSt's; p‐methylstyrene (MSt), p‐tert‐butylstyrene (BSt), 2‐vinylnaphthalene (VN), and p‐(tert‐butyldimethylsilyloxy)styrene (BMSiOSt)] were investigated with dimethylsilylene(tetramethylcyclopentadienyl)(N‐tert‐butyl)titanium dichloride to yield the corresponding ethylene–RSt copolymers. The substituent on the styrene (St) monomers did not affect the monomer reactivity ratio. The effect of the substituent structure of RSt on the thermal and mechanical properties was studied with differential scanning calorimetry, dynamic mechanical thermal spectroscopy, and elongation testing. The glass‐transition temperature (T_g) of the copolymers increased with increasing RSt content, and the order of T_g was as follows: BSt > VN > MSt = St. A copolymer with p‐hydroxystyrene (HOSt) was successively synthesized by means of deprotection of the copolymer with BMSiOSt. The copolymer showed a much higher T_g than the other copolymers because of the hydrogen connection of its OH groups. The mechanical properties of the copolymer in the glass state, at a lower temperature than T_g, were almost independent of the nature of the RSt. The substituent of the St monomers affected the pattern of the stress–strain curve in the elongation testing in the amorphous state. An improvement in the shape memory effect was observed in poly(ethylene‐co‐BSt). © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Toughening‐modified epoxy‐amine system: Cure kinetics,mechanical behavior,and shape memory performances

Shape memory epoxy resins are derived on reacting E51 with triethylenetetramine in presence of the toughening agent polypropylene glycol diglycidyl ether (PPGDGE). The curing behaviors are studied with differential scanning calorimetry. The toughening system shows a decrease in activation energy. ?esták–Berggren model is utilized to establish the kinetic equations. The fitting results prove that the equations can well describe the reactions. Tensile tests and dynamic mechanical analysis are used to analyze mechanical performances and thermodynamics. Shape memory properties are characterized by fold‐deploy tests. The elongation at break increases as the concentration of PPGDGE increases. The toughening materials have lower glass transition temperature (T_g). The fixable ratios of all systems are greater than 99.5%. The shape recovery time decreases with increasing the PPGDGE concentration. The optimal system can fully recover its original shape in about 2 min at T_g + 30°C, and exhibit the maximum fold‐deploy cycles as 13 cycles. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40853.     

Poly(dl‐Lactic Acid)‐Based Linear Polyurethanes Capable of Forming Physical Crosslinking via UPy Quadruple Hydrogen Bonding Assembly

Linear shape memory polyurethanes based on poly(dl ‐lactic acid) (PDLLA) macrodiol (PDLLA‐SMPUs) have various advantages such as good processability, biodegradability, shape memory effect, and biocompatibility, yet the insufficient mechanical properties prevent their effective applications in bone repair. 2‐Ureido‐4[1H]‐pyrimidone (UPy) can form strong quadruple hydrogen bonding. Here, a new linear PDLLA‐SMPU containing pendant UPy units (UPy‐p‐PDLLA‐SMPU) is designed and synthesized. The pendant UPy units may dimerize to form physical crosslinking among UPy‐p‐PDLLA‐SMPU chains. As a result, UPy‐p‐PDLLA‐SMPU demonstrates both good processability and significantly higher mechanical properties than the corresponding linear PDLLA‐SMPU without pendant UPys. In addition, UPy‐p‐PDLLA‐SMPU shows excellent shape memory effect near body temperature, with a shape fixity ratio of up to 98.6% and a recovery ratio of up to 92.9%. This work provides a new strategy to design SMPUs integrating the merits of linear and crosslinked polyurethanes, and the obtained UPy‐p‐PDLLA‐SMPU is a promising material for bone tissue repair in view of the mechanical, thermal, and shape memory properties.     

Poly(para‐dioxanone)/poly(D,L‐lactide) blends compatibilized with poly(D,L‐lactide‐co‐para‐dioxanone)

The effect of poly(D ,L ‐lactide‐co‐para‐dioxanone) (PLADO) as the compatibilizer on the properties of the blend of poly(para‐dioxanone) (PPDO) and poly(D ,L ‐lactide) (PDLLA) has been investigated. The 80/20 PPDO/PDLLA blends containing from 1% to 10% of random copolymer PLADO were prepared by solution coprecipitation. The PLADO component played a very important role in determining morphology, thermal, mechanical, and hydrophilic properties of the blends. Addition of PLADO into the blends could enhance the compatibility between dispersed PDLLA phase and PPDO matrix; the boundary between the two phases became unclear and even the smallest holes were not detected. On the other hand, the position of the T_g was composition dependent; when 5% PLADO was added into blend, the T_g distance between PPDO and PDLLA was shortened. The blends with various contents of compatibilizer had better mechanical properties compared with simple PPDO/PDLLA binary polymer blend, and such characteristics further improved as adding 5% random copolymers. The maximum observed tensile strength was 29.05 MPa for the compatibilized PPDO/PDLLA blend with 5% PLADO, whereas tensile strength of the uncompatibilized PPDO/PDLLA blend was 14.03 MPa, which was the lowest tensile strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Relation of swelling and Tg depression to the apparent free volume of a particle‐filled,epoxy‐based adhesive

The effect of hygrothermal aging on a particle‐filled, epoxy‐based adhesive was studied using a gravimetric sorption technique. This study has explored moisture sorption characteristics as well as the associated behaviors of swelling and the depression of the glass transition temperature (T_g). We observed that the diffusion of water in this adhesive has a non‐Fickian behavior, and the depression of T_g proceeds to a definite value that is independent of the final equilibrium water content of the system. Our observations suggest that water diffuses into the polymer in a dual‐sorption mode, in which water resides in two populations. In one population, water is considered to occupy apparent free volume of the adhesive, and the second population water infiltrates polymer structure and forms hydrogen‐bonded clusters. Our results show that hygrothermal aging temperature and swelling do not alter the apparent free volume of this adhesive. We conclude that the constant value of T_g depression at saturation implies that only water in the apparent free volume is responsible for the T_g depression, whereas the swelling proceeds through the formation of hydrogen bonds in the adhesive. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1436–1444, 2003     

Molecular simulation of the glass transition and proton conductivity of 2,2′‐benzidinedisulfonic acid and 4,4′‐diaminodiphenylether‐2,2′‐disulfonic acid‐based copolyimides as polyelectrolytes for fuel cell applications

The glass transition temperatures (T_gs) and proton conductivities of polyimides synthesized from naphthalene‐1,4,5,8‐tetracarboxylic dianhydride (NTDA), 2,2′‐benzidinedisulfonic acid (BDSA), 4,4′‐diaminodiphenylether‐2,2′‐disulfonic acid (ODADS), and non‐sulfonated diamine monomers have been predicted using molecular dynamics simulations. The specific volumes for two dry and four hydrated NTDA‐based polyimides were plotted versus temperatures above and below T_gs to obtain the glass transition temperatures. The simulation results suggest that the ODADS‐based polyimide membranes exhibit lower T_gs and thus better mechanical properties than the BDSA‐based polyimides, which may be attributed to the high mobility of backbones of ODADS as supported by the vectorial autocorrelation function (VACF) results of this study. In addition, comparison of the simulated T_gs for the dry and hydrated ODADS‐based polyimides has shown that water content in polyimides can affect their T_gs. The proton conductivities of a representative polyimide in both dry and hydrated conditions have been obtained from molecular dynamics simulations of the proton and hydronium ion diffusion. The simulated conductivity for the hydrated NTDA‐ODADS/BAPB cell is in reasonable agreement with the experimental value obtained from the AC impedance method. The relationship between the chemical composition, chain flexibility, and the glass transition and proton conduction of these NTDA‐based polyimides was explored on the basis of VACF and pair correlation function analysis. Copyright © 2006 Society of Chemical Industry     

Shape memory effect of poly(L‐lactide)‐ based polyurethanes with different hard segments

A series of biodegradable polylactide‐based polyurethanes (PLAUs) were synthesized using PLA diol (M_n = 3200) as soft segment, 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluene diisocyanate (TDI), and isophorone diisocyanate (IPDI) as hard segment, and 1,4‐butanediol as chain extender. The structures and properties of these PLAUs were studied using infrared spectroscopy, differential scanning calorimetry, tensile testing, and thermomechanical analysis. Among them, the MDI‐based PLAU has the highest T_g, maximum tensile strength, and restoration force, the TDI‐based PLAU has the lowest T_g, and the IPDI‐based PLAU has the highest tensile modulus and elongation at break. They are all amorphous. The shape recovery of the three PLAUs is almost complete in a tensile elongation of 150% or a twofold compression. They can keep their temporary shape easily at room temperature (20 °C). More importantly, they can deform and recover at a temperature below their T_g values. Therefore, by selecting the appropriate hard segment and adjusting the ratio of hard to soft segments, they can meet different practical demands for shape memory medical devices. Copyright © 2007 Society of Chemical Industry     

A new method to improve the stability,tensile strength,and heat resistant properties of shape‐memory epoxy resins: Two‐stages curing

In this article, we design a new thermal curing method: two‐stage curing. The purpose of using this approach is to maintain the excellent shape‐memory property of epoxy resin system after first stage curing, and the material can be folded in small size to storage or transportation and recovery its original shape commodiously by heating temperature. Then, after second stage curing, the stability, glass transition temperature(T_g), and tensile strength of material can be improved effectively. For this aim, a series of mixtures have been prepared. Differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), tensile test, scanning electron microscope (SEM), dynamic mechanical analysis (DMA), and fold‐deploy shape‐memory test have been used to characterize the feasibility of two‐stage curing process, curing degree, tensile strength, morphology, thermodynamic properties, and shape‐memory performance of these polymers. DSC results show that two independent curing stages can be achieved successfully. Tensile tests and DMA results suggest that tensile strength and heat resistance have been improved after the second curing stage. SEM results reveal that the addition of latent curing agent do not change the fracture mechanism. Furthermore, the fold‐deploy shape‐memory tests prove that the composites after first stage curing possess eximious shape‐memory property. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39882.     

Partially constrained recovery of (meth)acrylate shape‐memory polymer networks

The purpose of this study was to characterize the partial strain recovery of a thermoset shape‐memory polymer under a constraining stress. Three polymer networks were synthesized from tert‐butyl acrylate and poly(ethylene glycol) dimethacrylate (PEGDMA) solutions. The molecular weight and the weight fraction of the PEGDMA crosslinking monomer was altered systematically to maintain a constant glass transition temperature (T_g = 54°C) but tailorable rubbery moduli, which varied by almost an order of magnitude for the three polymer networks (E = 1.8–11.3°MPa). The shape‐recovery behavior of the polymers under a constraining stress was characterized for programming temperature below (20°C) and above (70°C) the T_g. The experiments revealed a peak in the recovered strain for samples programmed at 20°C. Recovered strain scaled linearly with the constraining stress by the rubbery modulus. The work performed by the shape‐memory polymer networks was observed to be primarily a function of constraining stress and crosslinking density, while programming temperature had a relatively mild influence; however, the efficiency of the shape‐memory effect was shown to be a function of constraining stress and programming temperature, but was independent of crosslinking density. Maximum work efficiencies (up to 45%) were observed for programming temperature of 70°C. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of molecular weight on shape memory behavior in polyurethane films

Understanding the relationship between the number‐average molecular weight (M_n) and the shape memory behavior of polymers is crucial for a complete picture of their thermomechanical properties, and hence for the development of smart materials, and, in particular, in textile technology. We report here on the study of shape memory properties as a function of M_n of polymers. Shape memory polyurethanes (SMPUs) of different M_n were synthesized, with various catalyst contents or molar ratio(r = NCO/OH) in the composition. In particular, two types of SMPU, namely T_m and T_g types according to their switch temperature type, were synthesized to compare the influence of M_n on their shape memory behavior. X‐ray diffraction, differential scanning calorimetry, dynamic mechanical analysis, and shape memory behavior results for the SMPUs are presented. The results indicate that the melting temperature (T_m), the glass transition temperature (T_g), the crystallinity, and the crystallizability of the soft segment in SMPUs are influenced significantly by M_n, before reaching a critical limit around 200 000 g mol^?1. Characterization of the shape memory effect in PU films suggests that the T_m‐type films generally show higher shape fixities than the T_g‐type films. In addition, this shape fixity decreases with increasing M_n in the T_g‐type SMPU, but the shape recovery increases with M_n in both types of SMPU. The shape recovery temperature, in contrast, decreases with M_n as suggested by the result of their thermal strain recovery. It is concluded that a higher molecular weight (M_n > 200 000 g mol^?1) is a prerequisite for SMPUs to exhibit higher shape recovery at a particular temperature. Copyright © 2007 Society of Chemical Industry     

Biodegradable polyurethane based on random copolymer of L‐lactide and ϵ‐caprolactone and its shape‐memory property

A series of biodegradable polyurethanes (PUs) are synthesized from the copolymer diols prepared from L ‐lactide and ε‐caprolactone (CL), 2,4‐toluene diisocyanate, and 1,4‐butanediol. Their thermal and mechanical properties are characterized via FTIR, DSC, and tensile tests. Their T_gs are in the range of 28–53°C. They have high modulus, tensile strength, and elongation ratio at break. With increasing CL content, the PU changes from semicrystalline to completely amorphous. Thermal mechanical analysis is used to determine their shape‐memory property. When they are deformed and fixed at proper temperatures, their shape‐recovery is almost complete for a tensile elongation of 150% or a compression of 2‐folds. By changing the content of CL and the hard‐to‐soft ratio, their T_gs and their shape‐recovery temperature can be adjusted. Therefore, they may find wide applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4182–4187, 2007     

Shape‐memory polymer networks with Fe3O4 nanoparticles for remote activation

Shape‐memory polymers (SMPs) have recently shown the capacity to actuate by remote heating via the incorporation of magnetic nanoparticles into the polymer matrix and exposure to an alternating magnetic field. In this study, methacrylate‐based thermoset SMP networks were synthesized through free‐radical polymerization with varying amounts of Fe₃O₄ magnetite (0, 1, and 2.5 wt %). Furthermore, the chemistry of the networks was controlled to maintain a constant glass transition temperature (T_g) while varying the degree of chemical crosslinking. Remote heating of the networks was shown to be a direct function of the nanoparticle concentration and independent of the chemistry. Magnetite reinforcement was shown to influence the thermomechanical properties of the networks; increasing Fe₃O₄ concentrations led to decreases in T_g and rubbery modulus. However, networks with a higher degree of crosslinking were more resistant to thermomechanical changes with respect to magnetite concentration. Strain to failure was shown to decrease with the addition of nanoparticles and the free‐strain shape‐memory cycle was investigated for all of the networks. Networks with lower degrees of crosslinking and high magnetite concentrations showed a significant amount of irrecoverable strain. Last, the use of remotely heated shape‐memory materials is discussed in light of potential biomedical applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Dynamic mechanical properties of polystyrene‐block‐poly[ethylene‐co‐(ethylene‐propylene)]‐block‐polystyrene triblock copolymer/hydrocarbon oil blends

Blend systems of polystyrene‐block‐poly(ethylene‐co‐(ethylene‐propylene))‐block‐polystyrene (SEEPS) triblock copolymer with three types of hydrocarbon oil of different molecular weight were prepared. The E″ curves as a function of temperature exhibited two peaks; one peak at low temperature (? ?50°C), arising from the glass transition of the poly[ethylene‐co‐(ethylene‐propylene)] (PEEP) phase and a high temperature peak (? 100°C), arising from the glass transition of the polystyrene (PS) phase. The glass transition temperature (T_g) of the PEEP phase shifted to lower temperature with increasing oil content. The shifted T_g depended on the types of oil and was lower for the low molecular weight oil. The T_g of PS phase of the present blend system, were found to be constant and independent of the oil content, when molecular weight of the oil is high. However, for the lower molecular weight oil, the T_g of the PS phase also shifted to lower temperatures. This fact indicates that the oil of high molecular weight is merely dissolved in the PS phase. The E′ at (75°C, at which temperature both of PEEP and PS phases are in glassy state, was found to be independent of oil content. In contrast, at 25°C, at which temperature the PEEP phase is in rubbery state, the E′ decreased sharply with increasing oil content. This result indicates that the hydrocarbon oil was a selective solvent in the PEEP phase. It mainly dissolved in the PEEP phase, although slightly dissolved into the PS phase as well, when molecular weight of oil is low. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011