Modified carrageenan. 4. Synthesis and swelling behavior of crosslinked κC‐g‐AMPS superabsorbent hydrogel with antisalt and pH‐responsiveness properties

To synthesize a novel biopolymer‐based superabsorbent hydrogel, 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS) was grafted onto kappa‐carrageenan (κC) backbones. The graft copolymerization reaction was carried out in a homogeneous medium and in the presence of ammonium persulfate (APS) as an initiator, N,N,N′,N′‐tetramethyl ethylenediamine (TMEDA) as an accelerator, and N,N′‐methylene bisacrylamide (MBA) as a crosslinker. A proposed mechanism for κC‐g‐AMPS formation was suggested and the hydrogel structure was confirmed using FTIR spectroscopy. The affecting variables on swelling capacity, i.e., the initiator, the crosslinker, and the monomer concentration, as well as reaction temperature, were systematically optimized. The swelling measurements of the hydrogels were conducted in aqueous solutions of LiCl, NaCl, KCl, MgCl₂, CaCl₂, SrCl₂, BaCl₂, and AlCl₃. Due to the high swelling capacity in salt solutions, the hydrogels may be referred to as antisalt superabsorbents. The swelling of superabsorbing hydrogels was measured in solutions with pH ranging 1 to 13. The κC‐g‐AMPS hydrogel exhibited a pH‐responsiveness character so that a swelling–deswelling pulsatile behavior was recorded at pH 2 and 8. The overall activation energy for the graft copolymerization reaction was found to be 14.6 kJ/mol. The swelling kinetics of the hydrogels was preliminarily investigated as well. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 255–263, 2005     

Fluconazole release through semi‐interpenetrating polymer network hydrogels based on chitosan,acrylic acid,and citraconic acid

Semi‐interpenetrating polymer network hydrogels with different compositions of chitosan (Cs), acrylic acid, and citraconic acid were synthesized via free‐radical polymerization with ethylene glycol dimethacrylate as a crosslinker. The variations of the swelling percentages of the hydrogels with time, temperature, and pH were determined, and Cs–poly(acrylic acid) (PAA) hydrogels were found to be most swollen at pH 7.4 and 37°C. Scanning electron micrographs of Cs–PAA and Cs–P(AA‐co‐CA)‐1 (Cs‐poly(acrylicacid‐co‐citraconir acid)^?1) were taken to observe the morphological differences in the hydrogels. Although the less swollen hydrogel, Cs–P(AA‐co‐CA)‐1, had a sponge‐type structure, the most swollen hydrogel, Cs–PAA, displayed a uniform porous appearance. Fluconazole was entrapped in Cs–P(AA‐co‐CA)‐1 and Cs–PAA hydrogels, and the release was investigated at pH 4.0 and 37°C. The kinetic release parameters of the hydrogels (the gel characteristic constant and the swelling exponent) were calculated, and non‐Fickian diffusion was established for Cs–PAA, which released fluconazole much more slowly than the Cs–P(AA‐co‐CA)‐1 hydrogel. A therapeutic range was reached at close to 1 h for both hydrogels. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermoreversible hydrogel. XVII. Investigation of the drug release behavior for [N‐isopropylacrylamide‐co‐trimethyl acrylamidopropyl ammonium iodide‐co‐3‐dimethyl (methacryloyloxyethyl) ammonium propane sulfonate] copolymeric hydrogels

A series of copolymeric hydrogels were prepared from various molar ratios of N‐isopropylacrylamide (NIPAAm), trimethyl acrylamidopropyl ammonium iodide (TMAAI), and 3‐dimethyl (methacryloyloxyethyl) ammonium propane sulfonate (DMAPS). Results showed that the swelling ratios of these copolymeric hydrogels increased with an increase of TMAAI content. The drug release behavior of the ionic thermosensitive hydrogels related to their ionicity and drug types. Results indicated that the release ratio of caffeine in the hydrogels was not affected by the ionicity of hydrogels, but increased with increasing of the swelling ratio. The anionic solute (phenol red) strongly interacted with cationic hydrogel (very large K_d), so the phenol red release ratio in cationic gels was very low. On the other hand, CV was adsorbed only on the skin layer of the cationic hydrogel because of the charge repulsion, and released rapidly. Therefore the release ratio was highest for cationic hydrogel to cationic drug. In addition, the partition coefficients (K_d) and the drug delivery behavior of the present gels were also investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1592–1598, 2002     

Synthesis and swelling behavior of thermosensitive IPN hydrogels based on sodium acrylate and N‐isopropyl acrylamide by a two‐step method

A series of interpenetrating polymer network (IPN) hydrogels having higher swelling ratio (SR) and thermosensitivity were synthesized from sodium acrylate (SA) and N‐isopropyl acrylamide (NIPAAm) by a two‐step method. A series of the porous poly(sodium acrylate ‐co‐1‐vinyl–2‐pyrrolidone) [poly(SA‐co‐VP)], (SV), hydrogels were prepared from acrylic acid having 90% degree of neutralization and VP monomer in the first step. The second step is to immerse the SV dried gels into the NIPAAm solution containing initiator, accelerator, and crosslinker to absorb NIPAAm solution and then polymerized to form the poly(SA‐co‐VP)/poly(NIPAAm) IPN hydrogels (SVN). The effect of the different molar ratios of SA/VP and the content of NIPAAm on the swelling behavior and physical properties of the SVN hydrogels was investigated. Results showed that the SVN hydrogels displayed an obviously thermoreversible behavior when the temperature turns across the critical gel transition temperature (CGTT) of poly(NIPAAm) hydrogel. The pore diameter distributions inside the hydrogel also indicated that the pore sizes inside the SVN hydrogels were smaller than those inside the SV hydrogels. At the same time, the more proportion of SA was added into the hydrogel, the larger pore diameter of the SV hydrogel was formed. The results also showed that the SR decreased with an increase of the VP content in the SV hydrogel and more obviously decreased in the SVN hydrogels. The SVN networks also showed stronger shear moduli than SV hydrogels. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Fast‐responding bulk hydrogels with microstructure

A new method was used for the production of fast‐responding bulk hydrogels with microstructure (BHMs) with a high swelling ratio. These BHMs were synthesized first by the formation of poly(N‐isopropylacrylamide‐co‐acrylic acid) (NIPAAm–AA) microgel particles and then by the crosslinking of the particles with N‐isopropylacrylamide monomer. The polymer obtained had the desired microstructure but was bulk (monolithic), so it could be used in a variety of applications. The NIPAAm–AA microgel particles were characterized with transmission electron microscopy, and the formed BHMs were characterized with scanning electron microscopy. Compared with conventional bulk hydrogels, the BHMs had very high swelling ratios and much faster swelling rates attributable to the collaboration of the ionized microgel particles and bulk hydrogels. An increase in the microgel particles embedded in the BHMs provided faster hydrogel swelling. The number of ionic acrylic acid groups in the hydrogels affected their swelling behavior. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 169–178, 2002     

Synthesis and superswelling behavior of carboxymethylcellulose–poly(sodium acrylate‐co‐acrylamide) hydrogel

In this paper, attention is paid to synthesis and swelling behavior of a superabsorbent hydrogel based carboxymethylcellulose (CMC) and polyacrylonitrile (PAN). The physical mixture of CMC and PAN was hydrolyzed in NaOH solution to yield hydrogel, CMC–poly(NaAA‐co‐AAm). During alkaline hydrolysis, the nitrile groups of PAN were completely converted to a mixture of hydrophilic carboxamide and carboxylate groups followed by in situ crosslinking of the grafted PAN chains. A proposed mechanism for hydrogel formation was suggested and the structure of the product was established using FTIR spectroscopy. The reaction variables affecting the swelling capacity of the hydrogel were systematically optimized to achieve a hydrogel with swelling capacity as high as possible. Swelling measurements of the synthesized hydrogels in various chloride salt solutions indicated a swelling‐loss with increase in the ionic strength of the salt solutions. The pH of the various solutions also affected the swelling of the superabsorbent. Furthermore, the present hydrogels showed a pH‐reversible property. Finally, the swelling kinetics of synthesized hydrogels with various absorbent particle sizes was briefly examined. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of novel pH‐sensitive chitosan‐poly(acrylamide‐co‐itaconic acid) hydrogels

Novel pH‐sensitive chitosan‐poly(acrylamide‐co‐itaconic acid) hydrogels were prepared by free radical copolymerization of acrylamide and itaconic acid (IA) in chitosan solution. The hydrogels were characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis, differential scanning calorimetry and the swelling ratios of the hydrogels in water (pH 6.8) and pH 1.2. The influence of composition on the thermal properties of the hydrogels was assessed. The glass transition temperatures of the samples increased with IA content, ranging from 110 to 136 °C. Swelling of the hydrogels was found to obey second‐order kinetics with respect to the remnant swelling, indicating that diffusion is controlled by the relaxation of chains. The equilibrium swelling degree was strongly dependent on pH and composition. At both pH values the highest water uptake was obtained for the IA‐free sample M1. From the equilibrium swelling results the average molar mass between crosslinks, M_c, and the crosslink density of the chitosan‐poly(acrylamide‐co‐itaconic acid) samples were calculated. The results evidenced the reinforcing effect of IA on the hydrogel structure. It is concluded that these highly swellable pH‐sensitive hydrogels can be useful for applications in biomedicine and pharmacy. © 2013 Society of Chemical Industry     

Sustained delivery of hydrocortisone acetate by CS/N‐vinyl‐2‐pyrrolidone/CaCO3 microparticle hybrid hydrogels

The goal of this research is to develop a composite hydrogel system for sustained release of therapeutic agents. The hybrid hydrogels were prepared by radiation crosslinking on aqueous solution of Chitosan (CS)/N‐vinyl‐2‐pyrrolidone (NVP) with different loads of CaCO₃ in the presence of hydrocortisone acetate (HCA), an anti‐inflammatory drugs. Physical characteristics of CS/NVP/CaCO₃ were studied using X‐ray diffraction (XRD) and infrared spectrophotometery (IR). The porous structure of resulted hydrogel was confirmed by SEM micrographs. The effect of doses and calcium carbonate amount on the swelling of the hydrogels was investigated. The ability of the prepared CS/NVP/CaCO₃‐based hybrid hydrogels to be used as drug carriers for anti‐inflammatory‐specific drug delivery system was estimated using HCA as a model drug. POLYM. COMPOS., 35:1176–1183, 2014. © 2013 Society of Plastics Engineers     

Horseradish peroxidase‐mediated in situ forming hydrogels from degradable tyramine‐based poly(amido amine)s

Horseradish peroxidase (HRP)‐mediated crosslinking of poly(amido amine) (PAA) copolymers was successfully applied in the preparation of in situ forming degradable hydrogels under physiological conditions. PAA copolymers containing different amounts of tyramine residues (termed as pAEEOL/TA) could be synthesized through Michael‐type addition between methylenebisacryamide and amine mixture of 2‐(2‐aminoethoxy) ethanol and tyramine (TA). Depending on the amount of TA residue, the HRP, and H₂O₂ concentration, the gelation times could be varied from about 50 to 350 s. The swelling and degradation experiments indicated under physiological conditions the pAEEOL/TA‐based hydrogels are completely degradable within 6–8 days. Rheological analysis revealed that storage modulus of the hydrogels increased from 2500 to 4100 Pa when increasing HRP concentrations. Importantly, pAEEOL/TA copolymers have low cytotoxicity. Moreover, NIH 3T3 (mouse embryonic fibroblast) cells exposed in the degradation products of pAEEOL/TA‐based hydrogels retained high cell viability, implying that the hydrogels are cyto‐biocompatible. In vitro release of methylene blue and IgG protein from pAEEOL/TA‐based hydrogels could be effectively sustained by encapsulation of the drug in the hydrogels. The results indicate that HRP‐crosslinked, degradable pAEEOL/TA‐based hydrogels are promising for biomedical applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of an alginate–poly(sodium acrylate‐co‐acrylamide) superabsorbent hydrogel with low salt sensitivity and high pH sensitivity

This article describes the synthesis and swelling behavior of a superabsorbing hydrogel based on sodium alginate (NaAlg) and polyacrylonitrile (PAN). The physical mixture of NaAlg and PAN was hydrolyzed with a solution of NaOH to yield an alginate–poly(sodium acrylate‐co‐acrylamide) [Alg–poly(NaAA‐co‐AAm)] superabsorbent hydrogel. A proposed mechanism for hydrogel formation was suggested, and the structure of the product was established with Fourier transform infrared spectroscopy. The effects of reaction variables were systematically optimized to achieve a hydrogel with a swelling capacity as high as possible. Under the optimized conditions concluded, the maximum capacity of swelling in distilled water was 610 g/g. The absorbency of the synthesized hydrogels was also measured in various salt solutions. The swelling ratios decreased with an increase in the ionic strength of the salt solutions. In addition, the swelling capacity was determined in solutions with pHs ranging from 1 to 13. The Alg–poly(NaAA‐co‐AAm) hydrogel exhibited pH responsiveness, so a swelling–deswelling pulsatile behavior was recorded at pHs 2 and 8. This on–off switching behavior made the hydrogel as a good candidate for the controlled delivery of bioactive agents. Finally, the swelling kinetics of the hydrogels with various particle sizes were preliminarily investigated as well. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2927–2937, 2006     

Fast swelling behaviors of thermosensitive poly(N‐isopropylacrylamide‐co‐methacryloxyethyltrimethyl ammonium chloride)/Na2WO4 cationic composite hydrogels

A facile method was explored to synthesize thermosensitive poly[N‐isopropylacrylamide (NIPAM)‐co‐methacryloxyethyltrimethyl ammonium chloride (DMC)]/Na₂WO₄ cationic hydrogels via copolymerization of NIPAM and DMC in the presence of Na₂WO₄. Na₂WO₄ acted as both a physical crosslinking agent and a porogen precursor. The hydrogels were characterized by Fourier transform infrared spectroscopy, energy dispersive X‐ray, thermogravimetry, environmental scanning electron microscopy, and transmission electron microscopy. Effects of various salt solutions, pH solutions on swelling were investigated. Thermosensitivity of the hydrogels were also investigated in various polar solvents at different temperatures. The resultant hydrogel showed a fast swelling rate and good salt tolerance. The hydrogels reached the swelling equilibrium within 10 min. Moreover, the swelling ratio of the hydrogels increased with the increase of the polarity of the solvent. In the water, the swelling ratio decreased with the increasing of temperature, but remained at a high level even at 80 °C since the pore structure weaken the lower critical solution temperature effect of PNIPAM. The swelling ratio increased instead in low polar solvent, while it became negligible in nonpolar solvent with the increasing of temperature. The whole swelling kinetics was fit for Schott's pseudo‐second order model. The hydrogels have a great potential as catalysts and smart materials. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46375.     

Preparation and swelling properties of semi‐IPN hydrogels based on chitosan‐g‐poly(acrylic acid) and phosphorylated polyvinyl alcohol

The phosphorylated poly(vinyl alcohol) (P‐PVA) samples with various substitution degrees were prepared through the esterification reaction of PVA and phosphoric acid. By using chitosan (CTS), acrylic acid (AA) and P‐PVA as raw materials, ammonium persulphate (APS) as an initiator and N,N‐methylenebisacrylamide as a crosslinker, the CTS‐g‐PAA/P‐PVA semi‐interpenetrated polymer network (IPN) ssuperabsorbent hydrogel was prepared in aqueous solution by the graft copolymerization of CTS and AA and followed by an interpenetrating and crosslinking of P‐PVA chains. The hydrogel was characterized by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), and differential scanning calorimetry (DSC) techniques, and the influence of reaction variables, such as the substitution degree and content of P‐PVA on water absorbency were also investigated. FTIR and DSC results confirmed that PAA had been grafted onto CTS backbone and revealed the existence of phase separation and the formation of semi‐IPN network structure. SEM observations indicate that the incorporation of P‐PVA induced highly porous structure, and P‐PVA was uniformly dispersed in the polymeric network. Swelling results showed that CTS‐g‐PAA/P‐PVA semi‐IPN superabsorbent hydrogel exhibited improved swelling capability (421 g·g^?1 in distilled water and 55 g·g^?1 in 0.9 wt % NaCl solution) and swelling rate compared with CTS‐g‐PAA/PVA hydrogel (301 g·g^?1 in distilled water and 47 g·g^?1 in 0.9 wt % NaCl solution) due to the phosphorylation of PVA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Tremendous reinforcing,pore‐stabilizing and response‐accelerating effect of in situ generated nanosilica in thermoresponsive poly(N‐isopropylacrylamide) cryogels

The tremendous reinforcing and pore‐stabilizing effect of in situ formed nanosilica in a highly porous temperature‐responsive poly(N‐isopropylacrylamide) (PNIPA) matrix is demonstrated. A very weakly crosslinked semi‐liquid hydrogel can be reinforced to the point that it displays a fast, extensive and nearly symmetric temperature‐responsiveness in combination with an acceptable modulus. In soft but solid porous PNIPA, only 0.6 wt% of the nanofiller is sufficient to stabilize the pores against collapse upon de‐swelling, thus enabling ultrafast responsiveness. A spectacular effect is achieved with dried porous PNIPA (matrix is glassy, T_g ≈ 140 °C), which in the case of optimal nanosilica amounts can re‐swell in only 3 min. The key importance of efficient hydrogen bridging between PNIPA and SiO₂ is demonstrated by comparing in situ formed nanosilica with similarly sized commercial Ludox particles, the surface of which is saturated with ammonia (for stabilization). Synthesis parameters like the amount of crosslinker and of nanosilica were varied in a wide range, in order to achieve the fastest possible responsiveness of the hydrogels in combination with a high modulus. The porosity, nanosilica distribution, moduli, temperature‐dependent swelling as well as the swelling kinetics of the gels were determined as functions of contents of crosslinker and nanosilica. © 2017 Society of Chemical Industry     

Poly(N‐isopropylacrylamide‐co‐sodium acrylate) hydrogels: Interactions with surfactants

Poly(N‐isopropylacrylamide‐co‐sodium acrylate) [poly(NIPAM‐co‐SA)] hydrogels were modified with three different kind of surfactants (cationic, anionic, and nonionic) to study the effect on the swelling properties. The structural variation of the surfactant‐modified hydrogels was investigated in detail. The interaction between the surfactants and the hydrogel varies and strictly depends on the surfactant type. The variation in thermal stability of the modified surfactant hydrogels was investigated and compared with unmodified hydrogel. Further, the hydrogel swelling/diffusion kinetic parameters were investigated and diffusion of water into hydrogel was found to be of the non‐Fickian transport mechanism. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3423–3430, 2007     

Swelling characteristics of thermo‐ sensitive poly[(2‐diethylaminoethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] porous hydrogels

Temperature‐sensitive poly[(2‐diethylaminoethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] [P(DEAEMA‐co‐DMAAm)] hydrogels with five different DMAAm contents were synthesized with and without the addition of sodium carbonate as porosity generator. The synthesized hydrogels were characterized with dry gel density measurements, scanning electron microscopy observation and the determination of swelling ratio. The influence of the pore‐forming agent and content of DMAAm on swelling ratio and network parameters such as polymer–solvent interaction parameter (χ), average molecular mass between crosslinks (M?_c) and mesh size (ζ) of the cryogels are reported and discussed. The swelling and deswelling rates of the porous hydrogels are much faster than for the same type of hydrogels prepared via conventional methods. At a temperature below the volume phase transition temperature, the macroporous hydrogels also absorbed larger amounts water compared to that of conventional hydrogels and showed obviously higher equilibrated swelling ratios in aqueous medium. In particular, the unique macroporous structure provided numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to the external temperature changes during the deswelling and swelling processes. These properties are attributed to the macroporous and regularly arranged network of the porous hydrogels. Scanning electron micrographs reveal that the macroporous network structure of the hydrogels can be adjusted by applying porosity generation methods during the polymerization reaction. Copyright © 2007 Society of Chemical Industry     

Property modulation of poly(N‐isopropylacrylamide) hydrogels by incorporation of modified silica

Poly(N‐isopropylacrylamide) (PNIPA)/silica composite hydrogels were prepared and the effects of the silica incorporation on the swelling and breaking characteristics of the hydrogels were investigated. To improve the dispersive property of silica in the PNIPA matrix via the formation of covalent bonds between the polymer and silica, vinyl groups were introduced in the silica by reacting it with a coupling agent, 3‐methacryloxypropyltrimethoxysilane. When unmodified silica was used as filler in the PNIPA‐composite hydrogel, the swelling ratio of the composite hydrogel below the critical gel transition temperature (CGTT) increased with increasing silica content. However, when the modified silica was used as the filler, the swelling ratio below CGTT decreased with increasing silica content because of the enhanced distribution and additional crosslinking. Above CGTT, the swelling ratios of the PNIPA/silica hydrogels were similar regardless of the silica modification. The gel breaking stress of the hydrogels increased with increasing silica content, and this enhancement was larger for the modified silica hydrogel. Scanning electron microscopy images showed that the modified silica particles were distributed more evenly in the PNIPA matrix than the unmodified ones were and that the size of cell‐like structure of the hydrogel decreased with increasing modified silica content. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Preparation and swelling characterization of poly (n‐isopropylacrylamide)‐based porous hydrogels

Nine different poly(n‐isopropylacrylamide)‐based hydrogels, including nonionic, cationic, and anionic hydrogels, were synthesized in with and without the addition of pore‐forming agents. The synthesized hydrogels were characterized with dry gel density measurements, scanning electron microscopy observations, and the determination of the swelling ratio swelling kinetics. All the results showed that the cationic hydrogels had faster swelling kinetics than the anionic and nonionic hydrogels. The addition of pore‐forming agents (NaHCO₃ and carboxymethylcellulose) during the synthesis process led to porous hydrogels with lower dry densities, swelling ratios, and swelling kinetic parameter values. An empirical equation was developed to successfully correlate the swelling kinetic parameter with the hydrogel swelling ratio. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3651–3658, 2004     

Superabsorbent composite. XIII. Effects of Al3+‐attapulgite on hydrogel strength and swelling behaviors of poly(acrylic acid)/Al3+‐attapulgite superabsorbent composites

Al³⁺‐attapulgite (Al³⁺‐APT) was prepared by treating attapulgite (APT) with AlCl₃ aqueous solution of various concentrations. The poly(acrylic acid)/Al³⁺‐attapulgite (PAA/Al³⁺‐APT) superabsorbent composite was prepared by reaction of partly neutralized acrylic acid, and Al³⁺‐APT in aqueous solution using N, N′‐methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. The surface morphology of the composite was investigated by SEM, and the Al³⁺‐APT composite generated a relatively planar surface comparing the nature APT. The effects of Al³⁺‐APT on hydrogel strength and swelling behaviors, such as equilibrium water absorbency, swelling rate, and reswelling capability, of the superabsorbent composites were also studied. The hydrogel strength and reswelling capability were improved, however, the equilibrium water absorbency and swelling rate decreased with increasing AlCl₃ solution concentration. The equilibrium water absorbency firstly increased, and then decreased with increasing Al³⁺‐APT content. The results indicate that Al³⁺‐APT acts as an assistant crosslinker in the polymeric network, which has great influences on hydrogel strength and swelling behaviors of the PAA/Al³⁺‐APT superabsorbent composites. POLYM. ENG. SCI., 47:619–624, 2007. © 2007 Society of Plastics Engineers.     

Electrical actuation of electroresponsive hydrogels based on poly(acrylamide‐co‐acrylic acid)/graphite suitable for biomedical applications

A pH‐sensitive composite hydrogel based on poly(acrylamide‐co‐acrylic acid)/graphite was prepared by solution polymerization process in presence of redox initiator potassium persulfate/N,N,N′,N′‐tetramethylethylenediamine and cross‐linker (ethylene glycol dimethylacrylate). The structures of the hydrogels were confirmed using Fourier transform infrared, X‐ray diffraction, and scanning electron microscopy (SEM) study. Tensile strengths of the hydrogels were determined by using a universal tensile machine, whereas the electrical conductivities of the hydrogels were evaluated using Four‐probe method. The influence of cross‐linker, graphite content, and temperature on the conductivity of the hydrogel was also investigated. The bending behavior of the conducting hydrogels was investigated by exposing the hydrogels under electric field in aqueous medium. By studying the swelling ratio of the polymer synthesized under different conditions, optimization conditions were found for a polymer with the highest swelling ratio. Also, the hemolytic potentiality test revealed that prepared hydrogels are biocompatible in nature. POLYM. COMPOS., 35:27–36, 2014. © 2013 Society of Plastics Engineers     

Preparation of alginate/poly(N‐isopropylacrylamide) semi‐interpenetrating and fully interpenetrating polymer network hydrogels with γ‐ray irradiation and their swelling behaviors

Semi‐interpenetrating polymer network (semi‐IPN) and fully interpenetrating polymer network (full‐IPN) hydrogels composed of alginate and poly(N‐isopropylacrylamide) were prepared with γ‐ray irradiation. The semi‐IPN hydrogels were prepared through the irradiation of a mixed solution composed of alginate and N‐isopropylacrylamide (NIPAAm) monomer to simultaneously achieve the polymerization and self‐crosslinking of NIPAAm. The full‐IPN hydrogels were formed through the immersion of the semi‐IPN film in a calcium‐ion solution. The results for the swelling and deswelling behaviors showed that the swelling ratio of semi‐IPN hydrogels was higher than that of full‐IPN hydrogels. A semi‐IPN hydrogel containing more alginate exhibited relatively rapid swelling and deswelling rates, whereas a full‐IPN hydrogel showed an adverse tendency. All the hydrogels with NIPAAm exhibited a change in the swelling ratio around 30–40°C, and full‐IPN hydrogels showed more sensitive and reversible behavior than semi‐IPN hydrogels under a stepwise stimulus. In addition, the swelling ratio of the hydrogels continuously increased with the pH values, and the swelling processes were proven to be repeatable with pH changes. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4439–4446, 2006