Influence of different β‐nucleating agent on crystallization behavior,morphology, and melting characteristic of multiwalled carbon nanotube‐filled isotactic polypropylene nanocomposites

To obtain isotactic polypropylene (iPP) nanocomposites with high β‐crystal content, TMB5, calcium pimelate and calcium pimelate supported on the surface of nano‐CaCO₃ were used as β‐nucleating agent and MWCNT filled β‐nucleated iPP nanocomposites were prepared. The effect of different β‐nucleating agent and MWCNT on the crystallization behavior and morphology, melting characteristic and β‐crystal content of β‐nucleated iPP nanocomposites were investigated by DSC, XRD and POM. The results indicated that addition of MWCNT increased the crystallization temperature of iPP and MWCNT filled iPP nanocomposites mainly formed α‐crystal. The β‐nucleating agent can induce the formation of β‐crystal in MWCNT filled iPP nanocomposites. The β‐nucleating ability and β‐crystal content in MWCNT filled β‐nucleated iPP nanocomposites decreased with increasing MWCNT content and increased with increasing β‐nucleating agent content due to the nucleation competition between MWCNT and β‐nucleating agents. It is found that the calcium pimelate supported on the surface of inorganic particles as β‐nucleating agent has stronger heterogeneous β‐nucleation than calcium pimelate and TMB5. The MWCNT filled iPP nanocomposites with high β‐crystal content can be obtained by supported β‐nucleating agent. POLYM. COMPOS., 36:635–643, 2015. © 2014 Society of Plastics Engineers     

Effect of N,N′‐diphenyl adipamide on the formation of the β‐crystalline form in isotactic polypropylene

The polymorphic compositions and mechanical properties of isotactic polypropylene (iPP) samples nucleated by a selective β‐nucleating agent [N,N′‐diphenyl adipamide (DPA)] were investigated with wide‐angle X‐ray diffraction, polarized light microscopy, scanning electron microscopy, and mechanical tests. It was found that β‐phase crystals emerged with the addition of DPA, and the relative proportion of the β‐crystalline form reached the maximum value of 0.97 with the addition of 0.1 wt % DPA. The curved lamellae in the β spherulites were like flowers. The β spherulites were etched more easily than α spherulites because amorphous regions were distributed inside the β spherulites. The Izod notched impact strength increased sharply with the addition of DPA and attained the maximum value of 7.30 kJ/m² (the value of blank iPP was 3.13 kJ/m²) with the addition of 0.1 wt % DPA. An analysis of the misfit factors between DPA and β‐iPP showed that β‐iPP could epitaxially crystallize on the DPA crystal well. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of carbon nanotube‐supported β nucleating agent on the thermal properties,morphology, and mechanical properties of polyamide 6/isotactic polypropylene blends

A new kind of β nucleating agent, multi‐wall carbon nanotube (MWCNT)‐supported calcium pimelate was introduced into polyamide 6 (PA 6)/isotactic polypropylene (iPP; 10/90 by weight) blend and the thermal properties, morphology, and mechanical properties were investigated. The results showed that β‐iPP appeared at low content of MWCNT‐supported calcium pimelate which surmounted the α‐nucleating effect of PA 6 for iPP, and the content of β‐iPP increased with increasing content of MWCNT‐supported calcium pimelate. The impact strength, elongation at break, and flexural modulus were improved with increasing content of MWCNT‐supported calcium pimelate without significantly deteriorating the tensile strength. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Variation of non‐isothermal crystallization behavior of isotactic polypropylene with varying β‐nucleating agent content

The non‐isothermal crystallization behavior, the crystallization kinetics, the crystallization activation energy and the morphology of isotactic polypropylene (iPP) with varying content of β‐nucleating agent were investigated using differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). The DSC results showed that the Avrami equation modified by Jeziorny and a method developed by Mo and co‐workers could be successfully used to describe the non‐isothermal crystallization process of the nucleated iPPs. The values of n showed that the non‐isothermal crystallization of α‐ and β‐nucleated iPPs corresponded to a tridimensional growth with homogeneous and heterogeneous nucleation, respectively. The values of crystallization rate constant showed that the rate of crystallization decreased for iPPs with the addition of β‐nucleating agent. The crystallization activation energy increased with a small amount (less than 0.1 wt%) of β‐nucleating agent and decreased with higher concentration (more than 0.1 wt%). The changes of crystallization rate, crystallization time and crystallization activation energy of iPPs with varying contents of β‐nucleating agent were mainly determined by the ratio of the content of α‐ and β‐phase in iPP (α‐PP and β‐PP) from the DSC investigation, and the large size and many intercrossing lamellae between boundaries of β‐spherulites for iPPs with small amounts of β‐nucleating agent and the small size and few intercrossing bands among the boundaries of β‐spherulites for iPPs with large amounts of β‐nucleating agent from the SEM examination. Copyright © 2010 Society of Chemical Industry     

A highly active and selective β‐nucleating agent for isotactic polypropylene and crystallization behavior of β‐nucleated isotactic polypropylene under rapid cooling

Zinc adipate (Adi‐Zn) was observed to be a highly active and selective β‐nucleating agent for isotactic polypropylene (iPP). The effects of Adi‐Zn on the mechanical properties and the β‐crystals content of nucleated iPP were investigated. The impact strength of iPP nucleated with 0.2 wt % Adi‐Zn was 1.8 times higher than that of neat iPP. In addition, wide‐angle X‐ray diffraction analysis indicated that the content of β‐crystals in nucleated iPP (k_β value) reached 0.973 with 0.1 wt % Adi‐Zn, indicating that Adi‐Zn is a highly active and selective β‐nucleating agent for iPP. Furthermore, fast scanning chip calorimetry (FSC) studies using cooling rates from 60 to 13,800 °C min^?1 revealed that the formation of β‐crystals significantly depended on the cooling rates. At cooling rates below 3000 °C min^?1, only β‐crystals existed. However, at cooling rates above 6000 °C min^?1, β‐crystals failed to form. Moreover, a lower critical crystallization temperature that corresponded to the generation of β‐crystals was investigated using cooling‐induced crystallization, and the results are in good agreement with those of a previous study. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43767.     

On the differences in micro‐deformation mechanism between isotactic polypropylene and β‐nucleated isotactic polypropylene as revealed by the confocal laser scanning microscopy

To understand the toughness enhancement of β‐nucleated isotactic polypropylene (iPP) in comparison with iPP, the differences in the micro‐deformation mechanisms between the neat iPP and β‐nucleated iPP were visualized using the confocal laser scanning microscopy (CLSM). Structure of the α‐ and β‐spherulites situated close to the tip of the sharp starter crack has been investigated during tensile deformation in the viewing field of the CLSM. In the α‐spherulite of the neat iPP, highly localized inter‐ and intra‐spherulitic micro‐shear bands have been observed. In the β‐nucleated iPP, relatively uniform distribution of diffuse shear bands has been observed in the β‐phase, while the α‐phase remained relatively undeformed exhibiting only narrow intra‐spherulitic shear bands in the direction perpendicular to the loading direction. Delocalization of plastic deformation into diffuse shear bands in β‐nucleated iPP can explain its enhanced crack resistance compared with the neat iPP exhibiting highly localized shear banding. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Enhanced β‐crystal formation of isotactic polypropylene under the combined effects of acid‐corroded glass fiber and preshear

The acid‐corroded glass fiber (GF)/isotactic polypropylene (iPP) composite was injection molded by mixing–injection molding (MIM). Through this method, preshear can be imposed on melt during mix–plasticization process. The crystalline structure across the thickness direction of the injection‐molded bars was investigated by wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). It was unexpectedly found that, in core region, the acid‐corroded GF/iPP sample has the highest content of β‐form crystals, followed by uncorroded GF/iPP and neat iPP. Additionally, the crystalline morphology was investigated by polarized optical microscopy (POM) and scanning electron microscopy, and the results showed that β‐transcrystallization is preferably present in the acid‐corroded GF/iPP system. Confirmed by POM and DSC, the acid‐corroded GF shows strong β‐nucleation ability to iPP under static condition. Combined with the main features of MIM, three β‐nucleation origins in the acid‐corroded GF/iPP system under injection molding condition are proposed: (1) precursors induced by preshear in the barrel, (2) row‐nuclei induced by local shear, and (3) the acid‐corroded GF nuclei. POLYM. COMPOS. 34:1250–1260, 2013. © 2013 Society of Plastics Engineers     

Effects of EPDM and wollastonite on structure of isotactic polypropylene blends and composites

Polypropylene blends and composites with 5, 10, and 15 vol % of EPDM and 2, 4, and 6 vol % of untreated and treated wollastonite filler were examined by applying different techniques. Elastomeric ethylene/propylene/diene terpolymer (EPDM) component and wollastonite influenced the crystallization process of isotactic polypropylene (iPP) matrix in different ways. The nucleation of hexagonal β‐iPP, the increase of overall degree of crystallinity, and crystallite size of iPP were more strongly affected by wollastonite than the addition of EPDM was. Both ingredients also differently influenced the orientation of α‐form crystals in iPP matrix. Wollastonite increased the number of a*‐axis‐oriented α‐iPP lamellae plan parallel to the sample surface, whereas the addition of EPDM reoriented the lamellae. The orientation parameters of ternary composites exhibited intermediate values between those for binary systems because of the effects of both components. EPDM elastomer considerably affected well‐developed spherulitization of iPP, increasing the spherulite size. Contrary to EPDM, because of nucleating ability or crystal habit, wollastonite caused significantly smaller iPP spherulites. Small spherulites in ternary iPP/EPDM/wollastonite composites indicated that the wollastonite filler (even in smallest amounts) exclusively determined the morphology of ternary composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 4072–4081, 2004     

Nucleation effects of sodium and ammonium salts of 2,2′‐methylene‐bis‐(4,6‐di‐t‐butylphenylene)phosphate in isotactic polypropylene

The nucleation ability of isotactic poly(propylene) (iPP) to ammonium 2,2′‐methylene‐bis‐(4,6‐di‐t‐butylphenylene) phosphate (An) was investigated in the present work comparing with sodium 2,2′‐methylene‐bis‐(4,6‐di‐t‐butylphenylene) phosphate (NA‐11). Scanning electron microscope (SEM) revealed the crystalline morphology of both An and NA‐11 with planar surface characteristics. The observation of the fracture surface of nucleation iPP samples by SEM showed An particles were dispersed uniformly in polymer and had a better compatibility with iPP matrix than NA‐11 particles. Differential scanning calorimeter (DSC) showed that the melting temperature of An was 262°C significantly lower than that measured from NA‐11 group (above 400°C). Crystallization behaviors of iPP/NA‐11 and iPP/An were also investigated by DSC analysis, respectively. The results showed the crystallization peak temperature and the crystallinity of iPP/An were almost near to that of iPP/NA‐11. Furthermore, mechanical and optical properties of iPP were strongly improved in the presences of An and NA‐11. The flexural strength of iPP was elevated 34 and 35% and the haze value was reduced from 40.4 to 15.1 and 14.9% by the addition of 0.15 wt% NA‐11 and An, respectively. These results demonstrate that the nucleating agent of An described here is a good nucleating agent for the crystallization of iPP as well as NA‐11. POLYM. ENG. SCI., 55: 22–28, 2015. © 2014 Society of Plastics Engineers     

A novel β‐nucleating agent for isotactic polypropylene

The nucleating ability of p‐cyclohexylamide carboxybenzene (β‐NA) towards isotactic polypropylene (iPP) was investigated by differential scanning calorimetry, X‐ray diffraction, polarized optical microscopy and scanning electron microscopy. β‐NA is identified to have dual nucleating ability for α‐iPP and β‐iPP under appropriate kinetic conditions. The formation of β‐iPP is dependent on the content of β‐NA. The content of β‐phase can reach as high as 96.96% with the addition of only 0.05 wt% β‐NA. Under non‐isothermal crystallization the content of β‐iPP increases with increasing cooling rate. The maximum β‐crystal content is obtained at a cooling rate of 40 °C min^–1. The supermolecular structure of the β‐iPP is identified as a leaf‐like transcrystalline structure with an ordered lamellae arrangement perpendicular to the special surface of β‐NA. Under isothermal crystallization β‐crystals can be formed in the temperature range 80–140 °C. The content of β‐crystals reaches its maximum value at a crystallization temperature of 130 °C. © 2012 Society of Chemical Industry     

Investigation on the morphology and tensile behavior of β‐nucleated isotactic polypropylene with different stereo‐defect distribution

Large amount of work has been published on the tacticity‐properties relationship of isotactic polypropylene (iPP). However, the stereo‐defect distribution dependence of morphology and mechanical properties of β‐nucleated iPP (β‐iPP) is still not clear. In this study, two different iPP resins (PP‐A and PP‐B) with similar average isotacticity but different uniformities of stereo‐defect distribution were selected, their β‐iPP injection molding specimens were prepared, and the morphology evolution and tensile behaviors were studied by means of differential scanning calorimetry (DSC), 2D wide‐angle X‐ray diffraction (2D‐WAXD) and scanning electron microscope (SEM). DSC results showed that with the same concentration of β‐nucleating agent (0.3 wt % WBG‐II), PP‐B with more uniform stereo‐defect distribution exhibited more amount of β‐phase than that of PP‐A with less uniform stereo‐defect distribution, indicating that PP‐B is more favorable for the formation of β‐phase. SEM results showed that PP‐B formed more amount of β‐crystals with relatively high structural perfection, while in PP‐A a mixed morphology of α‐ and β‐phase with obviously higher amount of structural imperfection emerges. The results of room‐temperature tensile test indicated that the yield peak width of PP‐B was obviously wider, and the elongation at break of PP‐B was higher than that of PP‐A, showing a better ductile of PP‐B. The morphology evolution results of SEM, 2D‐WAXD and DSC suggest that, a combination of lamellar deformation and amorphous deformation occurred in PP‐A, while only amorphous deformation mainly took place in PP‐B, which was thought to be the reason for the different tensile behaviors of the samples. In the production of β‐PP products via injection molding, the uniformity of stereo‐defect distribution was found to be an important factor. PP with more uniform distribution of stereo‐defect favors the formation of large amount of β‐phase with high perfection, which exhibit superior ductile property. The related mechanism was discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 40027.     

Comparative study on the crystallization behavior of β‐isotactic polypropylene nucleated with different β‐nucleation agents —effects of thermal conditions

In this study, the crystallization behavior of the β‐isotactic polypropylene (β‐iPP) samples nucleated by a rare earth based β‐nucleating agent (β‐NA) WBG‐II and a metal salts compound β‐NA NAB83 (denoted as WPP and NPP, respectively) under different cooling conditions were comparatively investigated. The thermal conditions such as the cooling rate, isothermal crystallization temperature, isothermal crystallization time, and the subsequent cooling to room temperature. The results of WAXD, SEM, and nonisothermal crystallization reveal that under the same processing conditions, the crystallite size of NPP is smaller, which arrange more compactly as compared with WPP. Meanwhile, NPP has shorter crystallization rate and higher β‐nucleation selectivity, but WPP can crystallization at wider temperature range. The results of isothermal crystallization showed that NPP has higher selectivity and higher β‐nucleation efficiency, which favors the formation of high proportion of β‐phase at the isothermal crystallization temperature of 110–130°C with and without subsequent cooling; WPP has lower selectivity, which can only induce high content of β‐phase under isothermal crystallization without subsequent cooling to 25°C. In tuning the crystallization behavior and the properties of β‐PP, the joint influence of the efficiency and selectivity of the β‐NA, and the thermal conditions should be taken into consideration. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40115.     

Recrystallization behavior of β‐isotactic polypropylene in homogeneous and heterogeneous matrix–fiber composites

β‐isotactic polypropylene (β‐iPP) cylindritic crystals were produced in homogeneous iPP fiber–matrix composites and heterogeneous polyamide (PA)–iPP fiber–matrix composites under different sample preparation conditions. The melt recrystallization behaviors of the β‐iPP crystals obtained in the homogeneous and heterogeneous composites were studied by optical microscopy. The experimental results show that, by heating the sample to 180 °C, the birefringence contributed by the iPP crystals in both α‐ and β‐forms disappears completely. During the cooling process, the β‐iPP crystals in the homogeneous composite appear again, while the iPP in the heterogeneous composite crystallizes in its α‐form. This demonstrates the different origins of the β‐iPP cylindrites in the homogeneous and heterogeneous composites. While the β‐iPP cylindrites in the heterogeneous composite are associated with the sample preparation procedure, the β‐iPP cylindrites in the homogeneous composite are produced by recrystallization of the molten but incompletely relaxed iPP fibers. In situ observation of the melt recrystallization process shows that the molten iPP oriented fibers crystallize first during the cooling process at relatively higher temperature in the α‐form. Abundant randomly dispersed β‐iPP nuclei formed at the surface of the recrystallized iPP fibers, which generate the β‐iPP cylindrites. Copyright © 2012 Society of Chemical Industry     

α/β复合成核剂对等规聚丙烯结晶形态的影响及非等温结晶动力学

采用偏光显微镜(POM)及示差扫描量热(DSC)法考察了3种α/β复合成核剂NA40/NABW、NA40/HHPA-Ba、NA40/PA-03对成核等规聚丙烯(iPP)的结晶形态及非等温结晶动力学的影响。对成核iPP结晶形态的研究结果表明：α/β复合成核剂的加入能够减小iPP的球晶尺寸。影响α/β复合成核剂成核iPP结晶形态的主要因素是ΔT_Cp（ΔT_Cp为成核iPP结晶峰值温度与iPP结晶峰值温度的差值）,即复合体系中ΔT_Cp较大的成核剂在iPP结晶过程中起主导作用,最终的结晶形态与单独添加这一成核剂时iPP的结晶形态相类似;当两种成核剂的ΔT_Cp接近相同时,两者竞争成核,成核iPP的结晶形态表现为两种成核剂共同作用的结果。因此,通过改变α/β复合成核剂的复合比例即改变两种成核剂的添加浓度,进而改变其ΔT_Cp,可以得到结晶形态完全不同的iPP。采用Caze法对非等温动力学进行了研究,结果表明：添加α/β复合成核剂能够提高iPP的结晶温度,缩短半结晶时间。复合成核剂成核iPP的结晶行为也同样受成核剂ΔT_Cp的影响,复合成核iPP的Avrami指数接近于复合体系中ΔT_Cp较大的成核剂单独添加时iPP的Avrami指数。     

A highly effective reactive liquid crystal for the improved β‐nucleation of isotactic polypropylene

We report here the synthesis and characterization of a reactive liquid crystal (RLC) as a novel polymeric nucleating agent for the promotion of the nucleation efficiency of isotactic polypropylene (iPP). The RLC was synthesized by an in‐situ photo‐polymerization and was then grafted onto the molecular chain of iPP by the reactive blending. The phase transition and crystalline morphologies of RLC‐iPP in the β‐nucleation were studied. It is found that the nucleation efficiency of β‐crystals of iPP can be increased to 42% with a very small amount of RLC grafting, which is much higher than the reported nucleation efficiency of polymeric nucleating agents up to now (23%). In addition, we found that the nucleation efficiency of β‐crystals is strongly related to the concentration of RLC for the reactive blending. The nucleation efficiency was decreased from 42% to about 17% with the increase of RLC concentration from 0.5% to 4%. We propose a possible nucleation mechanism for this interesting phenomenon. It is expected that this new β‐nucleation RLC will have potential industrial applications in the future. POLYM. ENG. SCI., 54:2112–2120, 2014. © 2013 Society of Plastics Engineers     

Highly active thermally stable β‐nucleating agents for isotactic polypropylene

Calcium salts of suberic (Ca‐Sub) and pimelic (Ca‐Pim) acids were synthesized and implemented as in different grades of isotactic polypropylene (iPP). Propylene homopolymer, as well as random and block copolymers containing these additives, crystallized iPP into pure or nearly pure β modification in the isothermal and nonisothermal crystallization experiments. Recently, Ca‐Sub proved to be the most effective β‐nucleating agent of iPP. The Ca‐Sub nucleating agent widens the upper crystallization temperature range of pure β‐iPP formation up to 140°C. In this study the effect of the these additives on the crystallization, melting characteristics, and structure of the PP were studied. The degree of crystallinity of β‐iPP was markedly higher than that of α‐iPP. A widening in the melting peak of the samples crystallized in a high temperature range was first observed and discussed in regard to literature results of the same phenomenon for α‐iPP. The morphology of the β‐iPP samples was revealed by scanning electron microscopy. Independent of the type of polymer or nucleating agent, hedritic structures were found in the early stages of growth of the β‐spherulites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2357–2368, 1999     

Investigation of the crystalline phase morphology of a β‐nucleated impact polypropylene copolymer

This study covers the preparation and the characterization of β‐nucleated impact polypropylene copolymer (NA‐IPC). Calcium stearate (CaSt), as well as pimelic (Pim) and adipic (Adi) acids, were doped into IPC as mono‐ or bicomponent nucleating agents (NAs) at varying mass ratios. Possible chemical interactions between the NAs and with IPC, as well as the effect of the NAs on the crystallization behavior and nonisothermal crystallization kinetics, were investigated. DSC and XRD results revealed that IPC nucleated with Pim and Pim‐CaSt nucleants induced up to 90% β‐crystals, whereas Adi and Adi‐CaSt formed only about 17% β‐crystals. This was associated with the strong nucleation efficiency of Pim. The nonisothermal crystallization kinetics showed that the crystallization of IPC and NA‐IPC followed a three‐dimensional growth with athermal nucleation mechanism. FTIR showed that none of the NAs chemically reacted with IPC, and the chemical structure of the polymer was thus intact during the treatment. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39923.     

A novel highly efficient β‐nucleating agent for isotactic polypropylene

A novel highly efficient β‐nucleating agent for isotactic polypropylene (iPP), hexahydrophthalic barium (HHPA‐Ba), was found and its effects on the mechanical properties, the β‐phase content, and crystallization behavior of iPP were investigated, respectively. The results show that the β‐phase content of nucleated iPP (k_β value) can reach 80.2% with 0.4 wt % HHPA‐Ba. The impact strength and crystallization peak temperature of nucleated iPP are greatly increased. Compared with pure iPP, the impact strength of nucleated iPP can increase 2.4 times. Meanwhile, the spherulite size of nucleated iPP is dramatically decreased than that of pure iPP. The Caze method was used to investigate the nonisothermal crystallization kinetics of nucleated iPP and the crystallization active energy was achieved by Kissinger method. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Simultaneously improving tensile strength and toughness of melt‐spun β‐nucleated isotactic polypropylene fibers

Polymer processing methods generally play a crucial role in determining the development of microstructure in the fabricated product. In this study, isotactic polypropylene (iPP) melt containing 0.05 wt % β‐nucleating agent (β‐NA) was extruded via a melt flow rate indicator. The molten extrudate was stretched into a fiber upon various take‐up velocities (TVs). The microstructures of the fiber were investigated by differential scanning calorimeter, two‐dimensional wide‐angle X‐ray diffraction, and small‐angle X‐ray scattering. Also, its tensile properties (including tensile strength, modulus, elongation at break, and toughness) were measured by tensile test. Interestingly, the tensile strength (135.0 MPa) of a melt‐spun β‐nucleated iPP fiber fabricated at 400 cm/min was enhanced by 115.2%, compared with that (62.7 MPa) prepared at 100 cm/min, with a considerable increment in toughness (from 661 to 853 MJ/m³). The enhancement mechanism for tensile properties was discussed based on the microstructures. This work offers a simple approach to prepare β‐nucleated iPP fibers with excellent strength and toughness. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43454.     

Effect of nucleating duality on the formation of γ‐phase in a β‐nucleated isotactic polypropylene copolymer

BACKGROUND: It is a challenge for polymer processing to promote the formation of γ‐phase under atmospheric conditions in isotactic polypropylene (iPP) copolymer containing chain errors. Incorporation of an α‐nucleator in iPP copolymer seems reasonable since it can enhance non‐isothermal crystallization. Up to now, however, the issue regarding a β‐nucleated iPP copolymer still remains unclear, which is the subject of this study. RESULTS: The results indicate that the γ‐phase indeed occurs in a β‐nucleated random iPP copolymer with ethylene co‐unit (PPR) sample and becomes predominant at slow cooling rates (e.g. 1 °C min^?1) where the formation of the β‐form is suppressed to a large extent. With detailed morphological observations the formation of γ‐phase in the β‐nucleated PPR sample at slow cooling rate is unambiguously attributed to the nucleating duality of the β‐nucleator towards α‐ and β‐polymorphs. The α‐crystals, induced by the β‐nucleator, serve as seeds for the predominant growth of the γ‐phase. Moreover, the presence of the β‐nucleator, acting as heterogeneous nuclei, promotes the formation of γ‐phase in the nucleated PPR sample, at least to some extent. CONCLUSION: The findings in this study extend our insights into the formation of γ‐phase in β‐nucleated iPP copolymer and, most importantly, provide an alternative route to obtain iPP rich in γ‐phase. Copyright © 2008 Society of Chemical Industry