槐豆胶与黄原胶复配胶的流变性研究

对槐豆胶、黄原胶及其复配胶的流变性进行了研究。结果表明,槐豆胶和黄原胶有强烈的协效增稠性,槐豆胶与黄原胶复配胶的粘度随着浓度的升高而升高;复配胶为“非牛顿流体”;复配胶溶液的最佳加热温度和加热时间为60℃,加热60min;pH对复配胶的粘度有一定的影响;冻融变化使槐豆胶和黄原胶复配胶的粘度有较大幅度的增加。     

The effect of hydrolysed tragacanth gum and inulin on the probiotic viability and quality characteristics of low‐fat yoghurt

This study investigates the effect of supplementation of tragacanth gum (GT, 0.05% w/v), low molecular weight gum tragacanth (LMWGT, 0.5% w/v) and inulin (0.5% w/v) on the viability of Bifidobacterium bifidum and the quality parameters of low‐fat yoghurt during a three‐week storage period. The count of probiotics was found to be 7.8 log cfu/g in inulin, and LMWGT enriched yoghurts at the end of the storage period. The minimum water holding capacity and the maximum syneresis values were also obtained in the low‐fat yoghurt enriched with GT throughout the storage time. The samples containing inulin and LMWGT revealed sensory attributes that were judged superior compared to those in GT.     

Effect of medium molecular weight xanthan gum in rheology and stability of oil‐in‐water emulsion stabilized with legume proteins

Xanthan gum is a water‐soluble extracellular polysaccharide that has gained widespread commercial use because of its strong pseudoplasticity and tolerance to high ionic strength, which bring unique rheological properties to solutions. This study compares and evaluates the emulsifying properties of oil‐in‐water (30:70 v/v) emulsions stabilized with lupin and soya protein isolates and medium molecular weight xanthan gum. The protein was obtained by an isoelectric precipitation method and the polysaccharide was produced by Xanthomonas campestris ATCC 1395 in batch culture in a laboratory fermenter (LBG medium) without pH control. The addition of xanthan gum in the emulsion formulation enhances emulsion stability through the phenomenon of thermodynamic incompatibility with the legume protein, resulting in an increase of the adsorbed protein at the interface. The emulsion stability is also enhanced by a network structure built by the polysaccharide in the bulk phase. Copyright © 2005 Society of Chemical Industry     

黄原胶对酪蛋白酸钠乳状液稳定性的影响

研究了一定pH条件下,黄原胶浓度及剪切稀化效应对酪蛋白酸钠乳状液稳定性的影响。结果表明,在酸性条件下,黄原胶无法抑制酪蛋白的变性沉淀,乳液在制备之初,即产生严重絮凝。在中性和弱碱性条件下,黄原胶在一定浓度范围内,诱发了乳状液的排斥絮凝;体系的pH显著影响了乳状液的稳定性,pH6条件下,较低的黄原胶浓度(0.2wt%)便可赋予乳状液良好的稳定性。均质过程大大降低了黄原胶的粘度,导致乳状液的稳定性下降,与添加未经均质处理的黄原胶相比,添加量增大近一倍,才能获得稳定的乳状液。     

Anti‐obesity effect of feeding probiotic dahi containing Lactobacillus casei NCDC 19 in high fat diet‐induced obese mice

Nowadays, studies about the anti‐obesity potential of probiotics are of growing interest. Lactobacilli are one of the well‐studied probiotics owing to their preventing effect on metabolic disorders. This study was undertaken to access the anti‐obesity effect of probiotic dahi containing Lactobacillus casei NCDC 19 on C57BL/6 mice. Feeding of probiotic dahi showed reduce body weight gain and epididymal fat weights. Moreover, blood glucose, plasma lipids and expression level of leptin were reduced and caecal bifidobacteria counts and adiponectin expression levels were significantly increased. It can be concluded that feeding of probiotic dahi containing L. casei NCDC 19 showed potential anti‐obesity effects.     

Effect of locust bean/xanthan gum addition and replacement of pork fat with olive oil on the quality characteristics of low-fat frankfurters

The effects of reducing fat level from 20% to 12% and 9%, substituting pork fat with olive oil and adding locust bean/xanthan gum (0.5% and 0.6%) on emulsion stability, jelly and fat separation, processing yield, cook loss, texture and sensory characteristics of frankfurters were investigated and compared with control samples. Addition of locust bean/xanthan gum produced a significant increase in hydration/binding properties, characterised by lower cook losses, increasing yield, better emulsion stability and lower jelly and fat separation. The substitution of pork fat by olive oil did not affect these parameters. Indeed, results showed that reducing fat levels together with increasing moisture and locust bean/xanthan gum addition do not affect the sensory or textural properties, but olive oil addition produces a decrease in hardness and an increase in adhesiveness, however the overall acceptability was not affected.     

Effect of sucrose on rheological properties of xanthan gum-locust bean gum mixtures

Food Science and Biotechnology - The effect of sucrose (0, 10, 20, 30, and 40%) on flow and dynamic rheological properties of xanthan gum (XG) mixed with locust bean gum (LBG) at different mixing...     

Effect of xanthan gum on processing and cooking quality of nontraditional pasta

The physicochemical properties of three different commercial sources of xanthan gum (XG) were determined, and its subsequent effect on the processing and cooking quality of pasta containing nontraditional ingredients was characterised. Commercial durum flour was fortified with nontraditional ingredients (soya flour or oat flour, 10% w/w) and XG (2% w/w). Protein content, ash content, bulk density, water‐holding capacity and total glucose content significantly varied among XG samples from different vendors. Xanthan gum increased dough strength of durum flour and the extent of strengthening varied with vendor of XG. For example, time‐to‐peak ranged from 2.75 to 4.25 min; peak width from 2.5 to 3.75 BU; and end width from 2 to 3 BU depending on the vendor of XG. Processing properties differed depending on commercial source. Commercial XG that had the finest particle size required the lowest mechanical energy (range 253–270 J s^?1) and had the greatest extrusion rate (range 3.38–3.65 g s^?1), both of which resulted in the lowest specific mechanical energy (range 69–79 J g^?1) required to extrude spaghetti samples.     

黄原胶的流变性及与魔芋胶等的协效性研究

研究前期筛选获得一株多糖胶质高产菌Xanthomonas axonopodis所产的黄原胶FJAT-10151-DTJZ的品质,为该黄原胶的开发应用提供基础数据及参考。通过分析浓度、剪切速率、p H、加热温度、时间、冻融处理等对FJAT-10151-DTJZ粘度的影响研究其流变性,并研究其与结冷胶、黄原胶、凝胶多糖、瓜尔豆胶、刺槐豆胶、魔芋胶、果胶和壳聚糖8种胶的协效性。实验结果表明,FJAT-10151-DTJZ溶液的粘度随浓度的升高而升高,且为非牛顿流体;当FJAT-10151-DTJZ的浓度为1%时,其粘度为343 m Pa·s;p H、冻融对FJAT-10151-DTJZ的粘度影响不大;FJAT-10151-DTJZ的最佳加热温度为75℃;粘度随加热时间先增大后减小,当加热温度为75℃,加热时间为150 min,1%浓度的FJAT-10151-DTJZ溶液的粘度为808 m Pa·s。FJAT-10151-DTJZ只与魔芋胶有强烈的协同增效作用,与壳聚糖、结冷胶、黄原胶、凝胶多糖、瓜尔豆胶、刺槐豆胶、果胶无协效性。      

黄原胶对罗非鱼蛋白-大豆蛋白混合体系乳浊液稳定性的影响

以罗非鱼和豆粕为原料,采用碱溶-等电点沉淀法制备鱼分离蛋白(fish protein isolates,FPI)和大豆分离蛋白(soybean protein isolats,SPI),固定蛋白浓度0.5%,在pH 4.0和7.0条件下,高压均质(一级压力30 MPa,二级压力4 MPa),实验黄原胶(xanthan gum,XG)的添加对FPI、FPI-SPI(质量比2∶1)、FPI-SPI(质量比1∶1)和SPI乳浊体系粒径分布、微观显微结构和乳析指数的影响。结果表明:随着黄原胶的添加(0~0.09%),乳浊体系平均粒径减小(P0.05);在pH 4.0条件下,乳浊液液滴聚集和絮凝现象明显减少,宏观乳析稳定性提高(P0.05),添加0.06%和0.09%黄原胶的FPI-SPI混合乳浊体系4℃放置10 d都没有明显的分层,而不同比例混合蛋白体系之间的差异不明显(P0.05);在pH 7.0条件下,添加0.06%的黄原胶时,FPI-SPI(质量比2∶1)和FPI-SPI(质量比1∶1)混合乳浊体系微观絮凝现象没有明显改善,宏观乳析稳定性明显提高(P0.05),4℃放置10 d没有明显的分层现象。总体分析,2种蛋白物理混合对乳浊液体系稳定性的改善程度有限,而适量的黄原胶能明显提高酸性条件下体系的乳浊液稳定性。     

魔芋粉与黄原胶复配物对重组牛肉品质特性的影响

将转谷氨酰胺酶和酪蛋白酸钠作为重组牛肉使用的黏合剂,添加量为原料牛肉质量的1.2％(m/m).为了改善重组牛肉的品质特性,在此基础上添加魔芋粉与黄原胶复合物,通过测定重组牛肉的粘结强度、剪切力、解冻损失、蒸煮损失、色差和质构来说明食用胶对重组牛肉加工特性的影响.研究结果表明,魔芋粉与黄原胶的比例为6∶4,复合食品胶添加量为0.4％(m/m)时,重组牛肉的粘结强度最好(p＜0.05),生肉和熟肉的剪切力均最低,改善了肉的嫩度,使得重组肉具有最好的粘结效果.     

魔芋粉与黄原胶复配物对重组牛肉品质特性的影响

将转谷氨酰胺酶和酪蛋白酸钠作为重组牛肉使用的黏合剂,添加量为原料牛肉质量的1.2%(m/m)。为了改善重组牛肉的品质特性,在此基础上添加魔芋粉与黄原胶复合物,通过测定重组牛肉的粘结强度、剪切力、解冻损失、蒸煮损失、色差和质构来说明食用胶对重组牛肉加工特性的影响。研究结果表明,魔芋粉与黄原胶的比例为6:4,复合食品胶添加量为0.4%(m/m)时,重组牛肉的粘结强度最好(p<0.05),生肉和熟肉的剪切力均最低,改善了肉的嫩度,使得重组肉具有最好的粘结效果。      

Yoghurt‐type beverage with partial substitution of milk by a chickpea extract: Effect on physicochemical and flow properties

The objective of this study was to determine the evolution of physicochemical and flow properties of a yoghurt‐type beverage partially replaced with a chickpea extract over a period of 22 days. From two chickpea extracts, Blanco Noroeste was selected for its higher protein content. Six yoghurt‐type formulations were prepared, stored at 4 °C and analysed on days 1, 8, 15 and 22. pH was 4.24–4.75, while brightness was 81.7–94.5. Flow properties of the yoghurt‐type exhibited a non‐Newtonian behaviour. From three formulations that underwent sensory evaluation, the 30:70 mix obtained the highest acceptation. This yoghurt‐type beverage exhibited characteristics similar to natural yoghurt.     

Effect of Arabic gum,xanthan gum and orange oil on flavor release from diluted orange beverage emulsion

The influence of main emulsion components namely Arabic gum (13–20% w/w), xanthan gum (0.3–0.20% w/w) and orange oil (10–14% w/w) on semi-quantitative headspace analysis of target volatile flavor compounds released from a model orange beverage (diluted orange beverage emulsion) was evaluated by using a three-factor circumscribed central composite design (CCCD). For optimization procedure, the peak area of 13 volatile flavor compounds (i.e. ethyl acetate, α-pinene, ethyl butyrate, β-pinene, 3-carene, myrcene, limonene, γ-terpinene, octanal, decanal, linalool, neral and geranial) were considered as response variables. The response surface analysis exhibited that the significant (p < 0.05) second-order polynomial regression equations were successfully fitted for all response variables except for ethyl butyrate. A satisfactory coefficient of determination (R²) ranged from 0.831 to 0.969 (>0.8) was obtained for the response variables studied. No significant (p > 0.05) lack of fit was indicated for the reduced models except for the models fitted for limonene and linalool. This observation confirmed an accurate fitness of the reduced response surface models to the experimental data. The multiple response optimizations indicated that an orange beverage emulsion containing 15.87% (w/w) Arabic gum, 0.5% (w/w) xanthan gum and 10% (w/w) orange oil was predicted to provide the minimum overall flavor release.     

益生菌Lactobacillus casei Zhang发酵特性的评价

以L.acidophilus NCFM,L.rhamnosus GG,L.casei Shirota和Bifidobacterium animalis Bb12为参照,对益生菌L.casei Zhang的发酵特性进行了研究.结果表明:发酵结束时,添加L.casei Zhang的发酵乳具有较高的pH值和较低的滴定酸度.4℃贮藏28 d后,L.casei Shirota和Bifidobacterium animalis Bb12的蛋白水解能力下降,而L.asei Zhang,L addophilusNCFM和L.rhamnosus GG蛋白水解能力不断上升.尽管Lcasei Zhang在脱脂乳中的发酵速度低于对照益生菌.但贮藏期内其活菌数缓慢上升并于贮藏结束时达到最高.L.casei Zhang完全具备益生菌所应有的发酵特性,因此其适合应用于发酵乳的开发.     

Optimisation of wheat flour‐based sponge cake formulation containing tapioca starch and xanthan gum

The optimum formulation for wheat flour (WF)‐based sponge cakes containing tapioca starch (TS) and xanthan gum (Xan) was determined using the central composite design with two factors and response surface methodology (RSM). Effects of partial substitution of TS (5–15%) for WF in a 20% total flour blend and Xan (0.1–0.3%) on specific volume, parameters of texture profile analysis and sensory liking scores of baked sponge cakes were investigated. A second‐order polynomial response surface was used to explain the influence of TS and Xan on the dependent variables. Coefficients of determination (R² ≥ 0.75) of the response variables and significant regression models were used for RSM optimisation. Based on the RSM contour plots, the cake formulation containing 16% butter with desired physical properties (maximum specific volume; minimum hardness, gumminess and chewiness) and sensory quality (maximum overall liking) was found to be 11.09–11.88% TS and 0.10–0.11% Xan.