Influence of class F fly ash on the abrasion–erosion resistance of high-strength concrete

This study investigates the abrasion–erosion resistance of high-strength concrete (HSC) mixtures in which cement was partially replaced by four kinds of replacements (15%, 20%, 25% and 30%) of class F fly ash. The mixtures containing ordinary Portland cement were designed to have 28 days compressive strength of approximately 40–80 MPa. Specimens were subjected to abrasion–erosion testing in accordance with ASTM C1138. Experimental results show that the abrasion–erosion resistances of fly ash concrete mixtures were improved by increasing compressive strength and decreasing the ratio of water-to-cementitious materials. The abrasion–erosion resistance of concrete with cement replacement up to 15% was comparable to that of control concrete without fly ash. Beyond 15% cement replacement, fly ash concrete showed lower resistance to abrasion–erosion compared to non-fly ash concrete. Equations were established based on effective compressive strengths and effective water-to-cementitious materials ratios, which were modified by cement replacement and developed to predict the 28- and 91-day abrasion–erosion resistance of concretes with compressive strengths ranging from approximately 30–100 MPa. The calculation results are compared favorably with the experimental results.     

Filler effect and pozzolanic reaction of ground palm oil fuel ash

This research examines the compressive strength of mortar and how the filler effect and pozzolanic reaction of ground palm oil fuel ash (POFA) contribute to this strength. POFA and river sand were ground to three different particle sizes and used to replace Type I Portland cement at 10–40% by weight of binder to cast the mortar. The compressive strengths of ground POFA and ground river sand mortars were determined at various ages between 7 and 90 days. The results showed that the compressive strength of mortar due to the filler effect of ground river sand was nearly constant during the 7–90 day period for a specified replacement rate of cement. However, the compressive strength of mortar due to the filler effect tended to increase slightly with increased cement replacement. The pozzolanic reaction of ground POFA increased with increasing particle fineness of ground POFA, replacement rate of cement, and age of the mortar. The compressive strength contribution from the pozzolanic reaction of ground POFA was much more pronounced than the contribution from the filler effect when the smallest sizes of both materials were considered.     

Use of palm oil fuel ash as a supplementary cementitious material for producing high-strength concrete

The objective of this study is to investigate the use of ground palm oil fuel ash with high fineness (GPA) as a pozzolanic material to produce high-strength concrete. Samples were made by replacing Type I Portland cement with various proportions of GPA. Properties such as the compressive strength, drying shrinkage, water permeability, and sulfate resistance, were then investigated. After aging for 28 days, the compressive strengths of these concrete samples were found to be in the range of 59.5–64.3 MPa. At 90-day the compressive strength of concrete containing GPA 20% was as high as 70 MPa. The drying shrinkage and water permeability were lower than those of high-strength concrete made from Type I Portland cement. When the concrete samples were immersed in a 10% MgSO₄ solution for 180 days, the sulfate resistance in terms of the expansion and loss of compressive strength was improved. The results indicated that GPA is a reactive pozzolanic material and can be used as a supplementary cementitious material for producing high-strength concrete.     

Effect of palm oil fuel ash fineness on the microstructure of blended cement paste

This paper presents the effect of palm oil fuel ash fineness on the microstructure of blended cement paste. Palm oil fuel ash (POFA) was ground to two different finenesses. Coarse and high fineness palm oil fuel ash, with median particle sizes of 15.6 and 2.1 μm, respectively, were used to replace ordinary Portland cement (OPC) at 0%, 20% and 40% by binder weight. A water to binder (W/B) ratio of 0.35 was used for all blended cement pastes. The amorphous ground palm oil fuel ash was characterized by the Rietveld method. The compressive strength, thermogravimetric analysis and pore size distribution of the blended cement pastes were investigated. The test results indicate that the ground palm oil fuel ash was an amorphous silica material. The compressive strengths of the blended cement pastes containing coarse POFA were as high as that of OPC cement paste. Blended cement paste with high fineness POFA had a higher compressive strength than that with coarse POFA. The blended cement pastes containing 20% of POFA with high fineness had the lowest total porosity. The Ca(OH)₂ contents of blended cement paste containing POFA decreased with increasing replacement of POFA and were lower than those of the OPC cement paste. In addition, the POFA fineness had an effect on the reduction rate of Ca(OH)₂. Furthermore, the critical pore size and average pore size of blended cement paste containing POFA were lower than those of the OPC cement paste. The incorporation of high fineness POFA decreased the critical pore size and the average pore size of blended cement paste as compared to that with coarse POFA.     

Effect of W/C ratio on covering depth of fly ash concrete in marine environment

This investigation studied the effect of W/C ratio on covering depth required against the corrosion of embedded steel of fly ash concrete in marine environment up to 4-year exposure. Fly ash was used to partially replace Portland cement type I at 0%, 15%, 25%, 35%, and 50% by weight of cementitious material. Water to cementitious material ratios (W/C) of fly ash concretes were varied at 0.45, 0.55, and 0.65. The 200-mm concrete cube specimens were cast and steel bars with 12-mm diameter and 50 mm in length were inserted in the concrete with the covering depth of 10, 20, 50, and 75 mm. The specimens were cured in water for 28 days, and then placed to the tidal zone of marine environment in the Gulf of Thailand. Subsequently, the concrete specimens were tested for the compressive strength, chloride penetration profile and corrosion of embedded steel bar after being exposed to tidal zone for 2, 3, and 4 years. The results showed that the concrete mixed with Portland cement type I exhibited higher rate of the chloride penetration than the fly ash concrete. The chloride penetration of fly ash concrete was comparatively low and decreased with the increasing of fly ash content. The increase of fly ash replacement and the decrease of W/C ratio could reduce the covering depth required for the initial corrosion of the steel bar. Interestingly, fly ash concretes with 35% and 50% cement replacement and having W/C ratio of 0.65 provided better corrosion resistance at 4-year exposure than the control concrete with W/C ratio of 0.45. In addition, the covering depth of concrete with compressive strength of 30 MPa (W/C ratio of 0.65) could be reduced from 50 to 30 mm by the addition of fly ash up to 50%.     

Influence of elevated temperatures on physical and compressive strength properties of concrete containing palm oil fuel ash

The residual compressive strength of concrete containing palm oil fuel ash (POFA) after exposure to elevated temperatures and subsequent cooling was investigated. Specimens from ordinary Portland cement (OPC) and POFA concrete mixes were prepared and subjected to various temperature levels. The POFA concrete contains 20% partial replacement of cement by weight and the temperature levels are; 100, 300, 500 and 800 °C. Two cooling systems which include cooling at room temperature by the natural breeze and water-spray were involved. Compressive strength test was conducted on control specimens as well as concrete specimens revived through the two cooling systems. Physical properties accompanying thermal degradations were also assessed. Residual performance as a ratio of residual strength to original strength was evaluated. The residual performance was found to be higher in POFA concrete than in the normal concrete. In addition, water-cooling was realized to aggravate strength reduction in both normal and POFA concretes when compared with air-cooling. High temperature and cooling system were also found to have great influence on physical properties, such as; mass loss, discolouration and crack patterns.     

Utilization of bagasse ash as a pozzolanic material in concrete

The physical properties of concrete containing ground bagasse ash (BA) including compressive strength, water permeability, and heat evolution, were investigated. Bagasse ash from a sugar factory was ground using a ball mill until the particles retained on a No. 325 sieve were less than 5wt%. They were then used as a replacement for Type I Portland cement at 10, 20, and 30wt% of binder. The water to binder (W/B) ratio and binder content of the concrete were held constant at 0.50 and 350 kg/m³, respectively.The results showed that, at the age of 28 days, the concrete samples containing 10–30% ground bagasse ash by weight of binder had greater compressive strengths than the control concrete (concrete without ground bagasse ash), while the water permeability was lower than the control concrete. Concrete containing 20% ground bagasse ash had the highest compressive strength at 113% of the control concrete. The water permeability of concrete decreased as the fractional replacement of ground bagasse ash was increased. For the heat evolution, the maximum temperature rise of concrete containing ground bagasse ash was lower than the control concrete. It was also found that the maximum temperature rise of the concrete was reduced 13, 23, and 33% as compared with the control concrete when the cement was replaced by ground bagasse ash at 10, 20, and 30wt% of binder, respectively. The results indicate that ground bagasse ash can be used as a pozzolanic material in concrete with an acceptable strength, lower heat evolution, and reduced water permeability with respect to the control concrete.     

Evaluation of the sulfate resistance of concrete containing palm oil fuel ash

The effects of using palm oil fuel ash (POFA) as a new pozzolanic material on sulfate resistance in terms of expansion and loss in compressive strength of concretes exposed to 5% MgSO₄ solution for up to 24 months were evaluated. POFA was processed to obtain different sized particles: small and medium sizes (SP and MP) were produced by grinding, and the large size (LP) used unground POFA. Portland cement type I was replaced by SP, MP, and LP at a level of 10–40% by weight of binder. Results showed that unground POFA (LP) is not suitable for use as a cement replacement in concrete because it produces low compressive strength and can not improve the sulfate resistance of concrete. Increasing proportions of ground POFA (MP and SP), caused a decrease in the expansion of concrete bars and an increase in the loss in compressive strength. However, the expansion and loss in compressive strength were reduced when the POFA fineness was increased. The results suggested that ground POFA (MP and SP) could be used as a pozzolanic material and could also improve the sulfate resistance of concrete.     

Influence of fly ash on strength and sorption characteristics of cold-bonded fly ash aggregate concrete

Cold-bonded fly ash aggregate concrete with fly ash as part of binder or fine aggregate facilitates high volume utilization of fly ash in concrete with minimum energy consumption. This paper investigates the influence of fly ash on strength and sorption behaviour of cold-bonded fly ash aggregate concrete due to partial replacement of cement and also as replacement material for sand. While cement replacement must be restricted based on the compressive strength requirement at desired age, replacement of sand with fly ash appears to be advantageous from early days onwards with higher enhancement in strength and higher utilization of fly ash in mixes of lower cement content. Microstructure of concrete was examined under BSEI mode. Replacement of sand with fly ash is effective in reducing water absorption and sorptivity attributable to the densification of both matrix and matrix–aggregate interfacial bond. Cold-bonded fly ash aggregate concrete with a cement content of 250 kg/m³, results in compressive strength of about 45 MPa, with a total inclusion of around 0.6 m³ of fly ash in unit volume of concrete.     

Effect of Granulated Blast Furnace Slag and fly ash addition on the strength properties of lightweight mortars containing waste PET aggregates

In this work, the effect of Granulated Blast Furnace Slag (GBFS) and fly ash (FA) addition on the strength properties of lightweight mortars containing waste Poly-ethylene Terephthalate (PET) bottle aggregates was investigated. Investigation was carried out on three groups of mortar specimens. One made with only Normal Portland cement (NPC) as binder, second made with NPC and GBFS together and, third made with NPC and FA together. The industrial wastes mentioned above were used as the replacement of cement on mass basis at the replacement ratio of 50%. The size of shredded PET granules used as aggregate for the preparation of mortar mixtures were between 0 and 4 mm. The waste lightweight PET aggregate (WPLA)–binder ratio (WPLA/b) was 0.60; the water–binder (w/b) ratios were determined as 0.45 and 0.50. The dry unit weight, compressive and flexural–tensile strengths, carbonation depths and drying shrinkage values were measured and presented. The results have shown that modifying GBFS had positive effects on the compressive strength and drying shrinkage values (after 90 days) of the WPLA mortars. However, FA substitution decreased compressive and flexural–tensile strengths and increased carbonation depths. Nevertheless a visible reduction occurred on the drying shrinkage values of FA modifying specimens more than cement specimens and GBFS modified specimens. The test results indicated that, GBFS has a potential of using as the replacement of cement on the WPLA mortars by taking into consideration the characteristics. But using FA as a binder at the replacement ratio of 50% did not improve the overall strength properties. Although it was thought that, using FA as binder at the replacement ratio of 50% for the aim of production WPLA concrete which has a specific strength, would provide advantages of economical and ecological aspects.     

Effects of LOI of ground bagasse ash on the compressive strength and sulfate resistance of mortars

Raw bagasse ash collected from the Thai sugar industry has a high loss on ignition (LOI) of ～20%. When ground and ignited at 550 °C for 45 min, the LOI was reduced to ～5%. These high and low LOI of ground bagasse ashes were blended in the ratios of 1:2 and 2:1 by weight to give ground bagasse ashes with LOIs of 10% and 15%, respectively. Each of these ground bagasse ashes was used to replace Portland cement type I at 10%, 20%, 30%, and 40% by weight of binder to cast mortar.The results showed that the development of compressive strengths of mortars containing ground bagasse ash with high LOI was slower than that of mortar containing ground bagasse ash with low LOI. However, at the later age, both types of ground ash mortars displayed similar compressive strengths. Mortars containing high LOI (～20%) of ground bagasse ash at 20% and 30% by weight of binder could produce higher compressive strengths than a control mortar after 28 and 90 days, respectively. Mortar bars containing ground bagasse ash at 10% showed a greater potential sulfate resistance and displayed a reduce expansion compared to a control mortar. However, mortar bars containing high LOI (larger than 10%) of ground bagasse ashes showed greater deterioration from sulfate attack than the mortar bars containing low LOI (less than 10%) of ground bagasse ashes, especially at high replacement levels (30–40%).     

Effect of fly ash addition on the mechanical properties of tile adhesive

Statistical relationship between various strengths of tile adhesives in which cement or sand was partially replaced with fly ash was studied. A low-lime fly ash was used in five different replacement levels from 5% to 30% by weight of either cement or sand. The tensile adhesion, flexural and compressive strengths of adhesives were determined at 2, 7 and 28 days. In small substitution levels, sand replacement increased the tensile adhesion strength. No strong relationship was found between tensile adhesion strength and flexural or compressive strength of the specimens in which the fly ash was used as sand replacement (r < 0.659). Strong relationship was observed between the same properties when fly ash was used as cement replacement (r > 0.896). Flexural and compressive strength values showed quite strong relationship (r > 0.949). This may be due to the fact that both of these strength values were obtained on the same specimens.     

The effect of activator concentration on the residual strength of alkali-activated fly ash pastes subjected to thermal load

This investigation reports on a comparative study of the residual compressive strength at different temperatures of alkali-activated fly ash (AAFA) pastes chemically activated using sodium silicate with three different concentrations named 20, 30 and 40 (wt.%). The behaviour of different mixtures in conditions of rapid temperature changes was studied. Water quench test was applied to determine thermal shock resistance. The traditional Portland cement pastes were used as a reference. The temperatures ranging from 200 °C to 1000 °C with an increment of 200 °C has been examined. Pore solution pH and compressive strengths before and after exposure to elevated temperatures were determined. The various decomposition phases formed were identified using X-ray diffraction (XRD), thermogravimetric analysis (TGA), differential thermal analysis (DTG) and scanning electron microscopy (SEM). The results indicated that fly ash activated by sodium silicate is more able to resist degradation caused by exposure to elevated temperature than Portland cement system as its relative strengths are superior. In the hardened AAFA pastes, as activator concentration dosage increased as the relative compressive strengths and thermal shock resistance decreased. The AAFA system is able to maintain a sufficient high pH to retain the passive protective layer on the surface of any reinforcing steel present.     

Properties of self-compacting concretes made with binary,ternary, and quaternary cementitious blends of fly ash,blast furnace slag,and silica fume

Self-compacting concretes (SCCs) have brought a promising insight into the concrete industry to provide environmental impact and cost reduction. However, the use of ternary and especially quaternary cementitious blends of mineral admixtures have not found sufficient applications in the production of SCCs. For this purpose, an experimental study was conducted to investigate properties of SCCs with mineral admixtures. Moreover, durability based multi-objective optimization of the mixtures were performed to achieve an optimal concrete mixture proportioning. A total of 22 concrete mixtures were designed having a constant water/binder ratio of 0.44 and a total binder content of 450 kg/m³. The control mixture included only a Portland cement (PC) as the binder while the remaining mixtures incorporated binary, ternary, and quaternary cementitious blends of PC, fly ash (FA), ground granulated blast furnace slag (S), and silica fume (SF). Fresh properties of the SCCs were tested for slump flow diameter, slump flow time, L-box height ratio, and V-funnel flow time. Furthermore, the hardened properties of the concretes were tested for sorptivity, water permeability, chloride permeability, electrical resistivity, drying shrinkage, compressive strength, and ultrasonic pulse velocity. The results indicated that when the durability properties of the concretes were taken into account, the ternary use of S and SF provided the best performance.     

Effects of post-mercury-control fly ash on fresh and hardened concrete properties

Activated carbon injection is the most mature technology for mercury capture from coal burning power plants; however, this technology increases the carbon content and mercury concentration in the fly ash. This, in turn, may reduce the suitability of fly ash for use in concrete and call into question the safety of using fly ash derived from this process. The focus of this paper is to investigate the reuse potential of post-mercury-control fly ash in concrete by examining the influence of three fly ashes derived from the activated carbon injection on the air content, compressive strength, permeability, and resistance to freezing and thawing of concrete mixtures. Laboratory testing confirmed the influence of the carbon on the air content of the concrete. However there was no difficulty in entraining air in activated carbon injection fly ash concretes within the recommended dosage range of the air-entraining admixture. All air-entrained fly ash concretes exhibited excellent characteristics in compressive strength (?32.0 MPa, 4641 psi at 28 days), resistance to chloride-ion penetration (moderate to low at 28 days of age) and freeze–thaw (?90 average durability factor after 300 cycles). The possible leaching of toxic elements including mercury from one fly ash sample used in this study was also evaluated using the US Environmental Protection Agency’s Toxicity Characteristic Leaching Procedure. The test results indicated that the leaching of toxic elements was much lower than the contamination level.     

Effect of elevated temperature on physico-mechanical properties of blended cement concrete

Pozzolanas are readily available for use in concrete in the local markets for strength and/or durability enhancement. Although safety and security against disasters are not new, they still presuming a challenge. For instance, the fire resistive properties of concrete are of prime interest.Through this work, the effect of different kinds of pozzolana on the fire resistive properties of concrete was studied. Four types of pozzolana were incorporated into the concrete mixtures, i.e. metakaolin (MK), silica fume (SF), fly ash (FA), and ground granulated blast furnace slag (GGBS). Each of the employed pozzolana was used in two ratios: 10% and 20%, either in the form of cement replacement or as an addition without affecting the cement content. A total of 17 mixes were cast.For all mixtures, compressive strength is evaluated after 28 days of water curing. The mixtures’ compressive strengths were also evaluated after exposure to elevated temperatures: 200 °C, 400 °C, 600 °C, and 800 °C. The residual compressive strengths after heat exposure are evaluated. The formed cementitious phases after incorporation of pozzolana and the heat-induced transformations are investigated via the X-ray diffraction technique (XRD).Test results demonstrate the impact of each type of the employed pozzolana on the heat resistive properties of concrete in addition to their influence on the strength development of the investigated mixes. Therefore, a decision could be made regarding optimizing the benefits specific to each type of pozzolana and their employment method.     

Strength and water permeability of concrete containing palm oil fuel ash and rice husk–bark ash

In this paper, palm oil fuel ash and rice husk–bark ash, which are by-products from electricity generating power plants and disposed as wastes in landfills, were used as a partial cement replacement. They were ground and incorporated into concrete at the levels of 20%, 40% and 55% by weight of binder. Compressive strength and water permeability of concretes containing ground palm oil fuel ash (GPOA) and ground rice husk–bark ash (GRBA) were investigated. From the tests, the replacement of Portland cement by both materials resulted in the higher water demand in concrete mixtures as compared to ordinary Portland cement (OPC) concrete with compatible workability. The compressive strengths of concretes containing 20% of GPOA and GRBA were as high as that of OPC concrete and were reduced as the increase in the replacement ratios. Although the compressive strengths of concrete with the replacement of GPOA or GRBA up to 40% were lower than OPC concrete, their water permeabilities were still lower than that of OPC concrete. These results indicate that both of GPOA and GRBA can be applied as new pozzolanic materials to concrete with an acceptable strength as well as permeability.     

Comparison on efficiency factors of F and C types of fly ashes

Fly ashes are obtained from thermal power plants and they are pozzolanic materials, which can act as partial replacement material for both portland cement and fine aggregate. With their economical advantages and potential for improving fresh and hardened concrete performance, they have some benefits for using in concrete industry. In this study, the objective was to find the efficiency factors of Turkish C and F-type fly ashes and to compare their properties. Three different cement dosages were used (260, 320, 400 kg/m³), two different ratios (10% and 17%) of cement reduced from the control concretes and three different ratios (depending on cement reduction ratio) of fly ash were added into the mixtures. At the ages of 28 and 90 days, compressive strength, modulus of elasticity and ultrasound velocity tests were carried out. From the compressive strength results, the k efficiency factors of C and F-type fly ashes were obtained. As a result, it is seen that efficiency factors of the concrete produced by the replacement of F and C type fly ashes with cement increase with the increase in cement dosage and concrete age.     

Influence of the use of rice husk ash on the electrical resistivity of concrete: A technical and economic feasibility study

This study investigated the behavior of apparent electrical resistivity of concrete mixes with the addition of rice husk ash using Wenner’s four electrode method. Tests included compressive strength, porosity and electrical conductivity of the pore solution. The contents of rice husk ash tested were 10%, 20% and 30% and results were compared with a reference mix with 100% Portland cement and two other binary mixes with 35% fly ash and 50% blast furnace slag. Higher contents of rice husk ash resulted in higher electrical resistivity, which exceeded those of all other samples. However, for compressive strength levels between 40 MPa and 70 MPa, the mix with 50% blast furnace slag showed the best combination of cost and performance.     

Performance of self-compacting concrete containing different mineral admixtures

This paper presents experimental study on the properties of self-compacting concrete (SCC). Portland cement (PC) was replaced with fly ash (FA), granulated blast furnace slag (GBFS), limestone powder (LP), basalt powder (BP) and marble powder (MP) in various proportioning rates. The influence of mineral admixtures on the workability, compressive strength, ultrasonic pulse velocity, density and sulphate resistance of SCC was investigated. Sulphate resistance tests involved immersion in 10% magnesium sulphate and 10% sodium sulphate solutions for a period of 400 days. The degree of sulphate attack was evaluated using visual examination and reduction in compressive strength. The test results showed that among the mineral admixtures used, FA and GBFS significantly increased the workability and compressive strength of SCC mixtures. Replacing 25% of PC with FA resulted in a strength of more than 105 MPa at 400 days. Moreover, the presence of mineral admixtures had a beneficial effect on the strength loss due to sodium and magnesium sulphate attack. On the other hand, the best resistance to sodium and magnesium sulphate attacks was obtained from a combination of 40% GBFS with 60% PC.