CO<Subscript>2</Subscript> methanation and co-methanation of CO and CO<Subscript>2</Subscript> over Mn-promoted Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

A series of Mn-promoted 15 wt-% Ni/Al₂O₃ catalysts were prepared by an incipient wetness impregnation method. The effect of the Mn content on the activity of the Ni/Al₂O₃ catalysts for CO₂ methanation and the comethanation of CO and CO₂ in a fixed-bed reactor was investigated. The catalysts were characterized by N2 physisorption, hydrogen temperature-programmed reduction and desorption, carbon dioxide temperature-programmed desorption, X-ray diffraction and highresolution transmission electron microscopy. The presence of Mn increased the number of CO₂ adsorption sites and inhibited Ni particle agglomeration due to improved Ni dispersion and weakened interactions between the nickel species and the support. The Mn-promoted 15 wt-% Ni/Al₂O₃ catalysts had improved CO₂ methanation activity especially at low temperatures (250 to 400 °C). The Mn content was varied from 0.86% to 2.54% and the best CO₂ conversion was achieved with the 1.71Mn-Ni/Al₂O₃ catalyst. The co-methanation tests on the 1.71Mn-Ni/Al₂O₃ catalyst indicated that adding Mn markedly enhanced the CO₂ methanation activity especially at low temperatures but it had little influence on the CO methanation performance. CO₂ methanation was more sensitive to the reaction temperature and the space velocity than the CO methanation in the co-methanation process.

Open image in new window

     

Doped Ni Catalysts for Methane Reforming with CO<Subscript>2</Subscript>

Pb, Sb, Bi and Te doped Ni catalysts were prepared and used for methane reforming with CO₂ in order to diminish coke deposition. It was found that small amounts of Pb doped Ni catalysts exhibited excellent coke resistance ability with minor loss of the reforming activity. As the added amount of Pb increased from 0 to 0.015 (mole ratio between Pb/Ni), coke formation rate decreased from 166.7 mg-coke/g-cat h (on Ni/SiO₂) to 0, while the reforming activity decreased slightly from 73.2% to 63.3% (conversion of CO₂) at 800 °C, 60,000 ml(STP)/g-cat·h (CH₄ CO₂=1:1, no dilution gas in feed). Higher amounts of Pb and Sb, Bi, Te made Ni catalyst deactivated for methane reforming with CO₂.     

Effect of La as Promoter in the Photoreduction of CO<Subscript>2</Subscript> Over TiO<Subscript>2</Subscript> Catalysts

In this work, TiO₂ has been modified by treating it thermally together with different proportions (0.5–15 wt%) of La₂O₃. The resulting materials have been extensively characterized by XRD, TEM, N₂ adsorption isotherms, temperature-programmed CO₂ desorption, Raman, UV–Vis photoluminescence and X-ray photoelectron spectroscopies. The activity tests of these materials for the gas-phase photocatalytic reduction of carbon dioxide show that the main products of the reaction are in all cases CO and CH₄, together with H₂ from the parallel reduction of water. After the preparation procedure, La phases are best described as oxycarbonates, and lead to improved activity with respect to TiO₂ with La contents up to 5 wt%. Higher loadings do not, however, lead to further enhanced activity. Retarded electron–hole recombination and enhanced CO₂ adsorption are invoked as the key factors contributing to this activity improvement, which is optimized in the case of 0.5 wt% La leading to higher productions of CO and CH₄ and increased quantum efficiency with respect to titania.     

Zr-Modified SBA-15 Supported Ni Catalysts with Excellent Catalytic Performance of CO Selective Methanation in H<Subscript>2</Subscript>-Rich Fuels

CO selective methanation is a promising route for the purification of CO in H₂-rich gas for on-board H₂-based fuel cells. Herein, we synthesized a Zr-modified SBA-15 supported Ni catalyst, which exhibits both high catalytic performance, deep-removing CO concentration to below 10 ppm with a selectivity higher than 50% in a very low-temperature range (170–220 °C), and long-term stability. The results of XRD, XPS, TPR, TPD and TEM characterizations reveal that the doping of Zr not only improves the dispersion of Ni species, enhances the CO adsorption, but also suppresses the CO₂ adsorption, resulting in the prominent catalytic performance.

Graphical Abstract

Open image in new window

     

Preparation of amine-modified SiO<Subscript>2</Subscript> aerogel from rice husk ash for CO<Subscript>2</Subscript> adsorption

Amine-modified SiO₂ aerogel was prepared using 3-(aminopropyl)triethoxysilane (APTES) as the modification agent and rice husk ash as silicon source, its CO₂ adsorption performance was investigated. The amine-modified SiO₂ aerogel remains porous, the specific surface area is 654.24 m²/g, the pore volume is 2.72 cm³/g and the pore diameter is 12.38 nm. The amine-modified aerogel, whose N content is up to 3.02 mmol/g, can stay stable below the temperature of 300 °C. In the static adsorption experiment, amine-modified SiO₂ aerogel (AMSA) showed the highest CO₂ adsorption capacity of 52.40 cm³/g. A simulation was promoted to distinguish the adsorption between the physical process and chemical process. It is observed that the chemical adsorption mainly occurs at the beginning, while the physical adsorption affects the entire adsorption process. Meanwhile, AMSA also exhibits excellent CO₂ adsorption–desorption performance. The CO₂ adsorption capacity dropped less than 10 % after ten times of adsorption–desorption cycles. As a result, AMSA with rice husk ash as raw material is a promising CO₂ sorbent with high adsorption capacity and stable recycle performance and will have a broad application prospect for exhaust emission in higher temperature.     

A Novel Process for Renewable Methane Production: Combining Direct Air Capture by K<Subscript>2</Subscript>CO<Subscript>3</Subscript>/Alumina Sorbent with CO<Subscript>2</Subscript> Methanation over Ru/Alumina Catalyst

CO₂ methanation over supported ruthenium catalysts is considered to be a promising process for carbon capture and utilization and power-to-gas technologies. In this work 4% Ru/Al₂O₃ catalyst was synthesized by impregnation of the support with an aqueous solution of Ru(OH)Cl₃, followed by liquid phase reduction using NaBH₄ and gas phase activation using the stoichiometric mixture of CO₂ and H₂ (1:4). Kinetics of CO₂ methanation reaction over the Ru/Al₂O₃ catalyst was studied in a perfectly mixed reactor at temperatures from 200 to 300 °C. The results showed that dependence of the specific activity of the catalyst on temperature followed the Arrhenius law. CO₂ conversion to methane was shown to depend on temperature, water vapor pressure and CO₂:H₂ ratio in the gas mixture. The Ru/Al₂O₃ catalyst was later tested together with the K₂CO₃/Al₂O₃ composite sorbent in the novel direct air capture/methanation process, which combined in one reactor consecutive steps of CO₂ adsorption from the air at room temperature and CO₂ desorption/methanation in H₂ flow at 300 or 350 °C. It was demonstrated that the amount of desorbed CO₂ was practically the same for both temperatures used, while the total conversion of carbon dioxide to methane was 94.2–94.6% at 300 °C and 96.1–96.5% at 350 °C.     

Separation characteristics of tetrapropylammoniumbromide templating silica/alumina composite membrane in CO<Subscript>2</Subscript>/N<Subscript>2</Subscript>, CO<Subscript>2</Subscript>/H<Subscript>2</Subscript> and CH<Subscript>4</Subscript>/H<Subscript>2</Subscript> systems

Nanoporous silica membrane without any pinholes and cracks was synthesized by organic templating method. The tetrapropylammoniumbromide (TPABr)-templating silica sols were coated on tubular alumina composite support ( γ-Al₂O₃/ α-Al₂O₃ composite) by dip coating and then heat-treated at 550 °C. By using the prepared TPABr templating silica/alumina composite membrane, adsorption and membrane transport experiments were performed on the CO₂/N₂, CO₂/H₂ and CH₄/H₂ systems. Adsorption and permeation by using single gas and binary mixtures were measured in order to examine the transport mechanism in the membrane. In the single gas systems, adsorption characteristics on the α-Al₂O₃ support and nanoporous unsupport (TPABr templating SiO₂/ γ-Al₂O₃ composite layer without α-Al₂O₃ support) were investigated at 20–40 °C conditions and 0.0–1.0 atm pressure range. The experimental adsorption equilibrium was well fitted with Langmuir or/and Langmuir-Freundlich isotherm models. The α-Al₂O₃ support had a little adsorption capacity compared to the unsupport which had relatively larger adsorption capacity for CO₂ and CH₄. While the adsorption rates in the unsupport showed in the order of H₂> CO₂> N₂> CH₄ at low pressure range, the permeate flux in the membrane was in the order of H₂≫N₂> CH₄> CO₂. Separation properties of the unsupport could be confirmed by the separation experiments of adsorbable/non-adsorbable mixed gases, such as CO₂/H₂ and CH₄/H₂ systems. Although light and non-adsorbable molecules, such as H₂, showed the highest permeation in the single gas permeate experiments, heavier and strongly adsorbable molecules, such as CO₂ and CH₄, showed a higher separation factor (CO₂/H₂=5-7, CH₄/H₂=4-9). These results might be caused by the surface diffusion or/and blocking effects of adsorbed molecules in the unsupport. And these results could be explained by surface diffusion. This paper is dedicated to Professor Hyun-Ku Rhee on the occasion of his retirement from Seoul National University.     

Unexpected Support Effect in Hydrotreating: Evidence of a Metallic Character for ReS<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and ReS<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> Catalysts

Abstract  

Rhenium sulfide based catalysts were prepared by the incipient wetness impregnation method over alumina and silica supports and evaluated for 4,6-dimethyldibenzothiophene hydrodesulfurization in a high-pressure stirred-tank reactor. The catalyst prepared over silica was about six times more active for hydrodesulfurization than the corresponding catalyst prepared over alumina and a NiMo/Al₂O₃ industrial reference catalyst. This surprising and positive SiO₂ support effect was explained by a metallic character of the supported sulfide, which was demonstrated using a kinetic approach of competitive hydrogenations and by XPS characterization.     

CO and CO<Subscript>2</Subscript> methanation over Ni catalysts supported on alumina with different crystalline phases

The effect of alumina crystalline phases on CO and CO₂ methanation was investigated using alumina-supported Ni catalysts. Various crystalline phases, such as α-Al₂O₃, θ-Al₂O₃, δ-Al₂O₃, η-Al₂O₃, γ-Al₂O₃, and κ-Al₂O₃, were utilized to prepare alumina-supported Ni catalysts via wet impregnation. N₂ physisorption, H₂ chemisorption, temperature-programmed reduction with H₂, CO₂ chemisorption, temperature-programmed desorption of CO₂, and X-ray diffraction were employed to characterize the catalysts. The Ni/θ-Al₂O₃ catalyst showed the highest activity during both CO and CO₂ methanation at low temperatures. CO methanation catalytic activity appeared to be related to the number of Ni surface-active sites, as determined by H₂-chemisorption. During CO₂ methanation, Ni dispersion and the CO₂ adsorption site were found to influence catalytic activity. Selective CO methanation in the presence of excess CO₂ was performed over Ni/γ-Al₂O₃ and Ni/δ-Al₂O₃; these substrates proved more active for CO methanation than for CO₂ methanation.     

Fischer-Tropsch synthesis on the cobalt impregnated catalyst using carbon-coated Ni/SiO<Subscript>2</Subscript>

Carbon-coated Ni/SiO₂ prepared by dry reforming of CH₄ with CO₂ was applied for the preparation of the cobalt-based Fischer-Tropsch synthesis (FTS) catalyst with 20 wt%Co to elucidate the metal-support interaction to FTS activity after carbon depositions on the Ni/SiO₂. The deposited carbons on the reforming catalyst of Ni/SiO₂, which were mainly in the form of filamentous or encapsulated carbons, largely increased CO conversion compared with the fresh Ni/SiO₂ without a significant variation of hydrocarbon distributions. The deposited carbons on the Ni/SiO₂ play an important role in increasing the reducibility of cobalt oxides due to a mitigated metal-support interaction. The enhanced catalytic activity during FTS reaction is mainly attributed to the proper modification of the Ni/SiO₂ surfaces with encapsulated carbons on the exposed nickel surfaces, which largely alters the reducibility of cobalt oxides by reducing the interaction of cobalt particles with the carbon-coated Ni/SiO₂ surfaces.     

Simplified synthesis of K<Subscript>2</Subscript>CO<Subscript>3</Subscript>-promoted hydrotalcite based on hydroxide-form precursors: Effect of Mg/Al/K<Subscript>2</Subscript>CO<Subscript>3</Subscript> ratio on high-temperature CO<Subscript>2</Subscript> sorption capacity

Hydrotalcite was synthesized from hydroxide-form precursors to prepare a novel high-temperature CO₂ sorbent, and the effect of Mg/Al ratio on CO₂ sorption was studied. To enhance the CO₂ sorption capacity of the sorbent, K₂CO₃ was coprecipitated during the synthetic reaction. X-ray diffraction analysis indicated that the prepared samples had a well-defined crystalline hydrotalcite structure, and confirmed that K₂CO₃ was successfully coprecipitated in the samples. The morphology of the hydrotalcite was confirmed by scanning electron microscopy, and N₂ adsorption analysis was used to estimate its surface area and pore volume. In addition, thermogravimetric analysis was used to measure its CO₂ sorption capacity, and the results revealed that the Mg: Al: K₂CO₃ ratio used in the preparation has an optimum value for maximum CO₂ sorption capacity.     

Performance of Ni/Nano-ZrO2catalysts for CO preferential methanation简

Large surface areas nano-scale zirconia was prepared by the self-assembly route and was employed as support in nickel catalysts for the CO selective methanation. The effects of Ni loading and the catalyst calcination temperature on the performance of the catalyst for CO selective methanation reaction were investigated. The cata- lysts were characterized by Brunauer-Emmett-Teller （BET）, transmission electron microscope （TEM）, X-ray dif- fraction （XRD） and temperature-programmed reduction （TPR）. The results showed that the as-synthesized Ni/nano-ZrO2 catalysts presented high activity for CO methanation due to the interaction between Ni active particle and nano zir- conia support. The selectivity for the CO methanation influenced significantly by the particle size of the active Ni species. The exorbitant calcination resulted in the conglomeration of dispersive Ni particles and led to the decrease of CO methanation selectivity. Among the catalysts studied, the 7.5% （by mass） Ni/ZrO2 catalyst calcinated at 500℃ was the most effective for the CO selective methanation. It can preferentially catalyze the CO methanation with a higher 99% conversion in the CO/CO2 competitive methanation system over the temperature range of 260-280℃, while keeping the CO2 conversion relatively low.     

Aqueous-Phase Hydrogenolysis of Glycerol to 1,3-propanediol Over Pt-H<Subscript>4</Subscript>SiW<Subscript>12</Subscript>O<Subscript>40</Subscript>/SiO<Subscript>2</Subscript>

Abstract  

Hydrogenolysis of glycerol to 1,3-propanediol in aqueous-phase was investigated over Pt-H₄SiW₁₂O₄₀/SiO₂ bi-functional catalysts with different H₄SiW₁₂O₄₀ (HSiW) loading. Among them, Pt-15HSiW/SiO₂ showed superior performance due to the good dispersion of Pt and appropriate acidity. It is found that Br?nsted acid sites facilitate to produce 1,3-PDO selectively confirmed by Py-IR. The effects of weight hourly space velocity, reaction temperature and hydrogen pressure were also examined. The optimized Pt-HSiW/SiO₂ catalyst showed a 31.4% yield of 1,3-propanediol with glycerol conversion of 81.2% at 200 °C and 6 MPa.