Hydrogen environment embrittlement of stable austenitic steels

Seven stable austenitic steels (stable with respect to γ → α′ transformation at room temperature) of different alloy compositions (18Cr–12.5Ni, 18Cr–35Ni, 18Cr–8Ni–6Mn–0.25N, 0.6C–23Mn, 1.3C–12Mn, 1C–31Mn–9Al, 18Cr–19Mn–0.8N) were tensile tested in high-pressure hydrogen atmosphere to assess the role of austenite stability on hydrogen environment embrittlement (HEE). The influence of hydrogen on tensile ductility was small in steels that are believed to have a high initial portion of dislocation cross slip (18Cr–12.5Ni, 18Cr–35Ni, 18Cr–8Ni–6Mn–0.25N), while the effects of hydrogen were significantly greater in steels with other primary deformation modes (planar slip in 18Cr–19Mn–0.8N and 1C–31Mn–9Al or mechanical twinning in 0.6C–23Mn and 1.3C–12Mn) despite comparable austenite stability at the given test conditions. It appears that initial deformation mode is one important parameter controlling susceptibility to HEE and that martensitic transformation is not a sufficient explanation for HEE of austenitic steels.     

The effect of age-hardening mechanism on hydrogen embrittlement in high-nitrogen steels

The effect of age-hardening regime on peculiarities of hydrogen-assisted fracture and tensile properties in two high-nitrogen Fe-23Cr-17Mn-0.1C-0.6N and Fe-19Cr-22Mn-1.5V-0.3C-0.9N steels was studied. A large number of intergranular (austenite/austenite) and interphase boundaries (austenite/coarse particle) provides high fraction of trapping sites for hydrogen atoms in V-alloyed steel. This leads to a change in fracture regime from transgranular brittle mode in coarse-grained V-free steel to intergranular brittle fracture of hydrogen-assisted surface layers in fine-grained V-alloyed steel with coarse (V,Cr)(N,C) particles. The formation of cells (Cr₂(N,C) particles and austenite) along the grain boundaries due to discontinuous precipitate-hardening reaction facilitates predominantly interphase hydrogen-assisted fracture for both steels. The complex reaction of the particle-strengthening mechanisms including discontinuous precipitation with formation of austenite/Cr₂(N,C)-plates interfaces or homogeneous nucleation of coherent (V,Cr)(N,C) particles in austenite (age-hardening regime 700 °C, 10 h) promotes mainly transgranular cleavage-like fracture mode under hydrogen-charging. The structural scheme is proposed to describe a change in hydrogen-assisted fracture micromechanisms and tensile properties of the steels with different density and distribution of interphase and intergranular boundaries.     

Influence of macro segregation on hydrogen environment embrittlement of SUS 316L stainless steel

The objective of this work is to identify microstructural variables that lead to the large scatter of the relative resistance of 316 grade stainless steels to hydrogen environment embrittlement. In slow displacement rate tensile testing, two almost identical (by nominal chemical composition) heats of SUS 316L austenitic stainless steel showed significantly different susceptibilities to HEE cracking. Upon straining, drawn bar showed a string-like duplex microstructure consisting of α′-martensite and γ-austenite, whereas rolled plate exhibited a highly regular layered α′-γ structure caused by measured gradients in local Ni content (9.5–13 wt%). Both martensite and austenite are intrinsically susceptible to HEE. However, due to Ni macro segregation and microstructural heterogeneity, fast H-diffusion in martensite layers supported a 10 times faster H-enhanced crack growth rate and thus reduced tensile reduction in area. Nickel segregation is thus a primary cause of the high degree of variability in H₂ cracking resistance for different product forms of 316 stainless steel.     

Influence of surface martensite layer on hydrogen embrittlement of Fe-Mn-C-Mo steels in wet H2S environment

This study investigated the effect of thermally induced surface martensite layer on hydrogen embrittlement of Fe-16Mn-0.4C-2Mo (wt.%) (16Mn) and Fe-25Mn-0.4C-2Mo (wt.%) (25Mn) steels through slow strain rate stress corrosion cracking testing and proof ring testing in wet H₂S environment. The 16Mn steel had a surface layer of less than 150 μm in depth containing ε-martensite, α′-martensite and austenitic twins. The martensite layer is found to reduce the hydrogen embrittlement resistance of the steel. In comparison, the 25Mn steel developed a full α′-martensite surface layer, which exhibited practically nil effect on the hydrogen embrittlement resistance of the steel. The ε-martensite provides much larger interface areas with the mechanical twins of the austenite in the 16Mn steel than the α′-martensite/austenite interfaces in the 25Mn steel. These interfaces are hydrogen trapping sites and are prone to initiate surface cracks, as observed in the scanning electron microscope. The formation of the cracks is attributed to hydrogen concentration at the ε-martensite and austenitic twin interfaces, which accelerates material fracture.     

Effect of alloying elements on hydrogen environment embrittlement of AISI type 304 austenitic stainless steel

The chemical composition of an AISI type 304 austenitic stainless was systematically modified in order to evaluate the influence of the elements Mo, Ni, Si, S, Cr and Mn on the material’s susceptibility to hydrogen environment embrittlement (HEE). Mechanical properties were evaluated by tensile testing at room temperature in air at ambient pressure and in a 40 MPa hydrogen gas atmosphere. For every chemical composition, the corresponding austenite stability was evaluated by magnetic response measurements and thermodynamic calculations based on the Calphad method. Tensile test results show that yield and tensile strength are negligibly affected by the presence of hydrogen, whereas measurements of elongation to rupture and reduction of area indicate an increasing ductility loss with decreasing austenite stability. Concerning modifications of alloy composition, an increase in Si, Mn and Cr content showed a significant improvement of material’s ductility compared to other alloying elements.     

An Fe–Ni–Cr–H interatomic potential and predictions of hydrogen-affected stacking fault energies in austenitic stainless steels

While Fe–Ni–Cr austenitic stainless steels exhibit relatively good resistance to hydrogen embrittlement, they still suffer from significant degradation of ductility, fatigue and fracture properties in gaseous hydrogen environments. Experimental studies in the literature suggest that hydrogen reduces stacking fault energy in austenitic stainless steels. This phenomenon causes a large separation of partial dislocations and lower propensity for cross-slip. Whereas lower stacking fault energy does not correlate well with loss of ductility in the absence of hydrogen, lower stacking fault energy trends toward greater loss of ductility when hydrogen is present. Calculations of stacking fault energy are challenging for austenitic stainless steels. One main issue is that in alloys, stacking fault energy is not a single value but rather varies depending on local composition. Herein, we first report an Fe–Ni–Cr–H quaternary interatomic potential and then use this potential to perform time-averaged molecular dynamics simulations to calculate stacking fault energies for tens of thousands of realizations of local compositions for selected stainless steels alloys with and without internal hydrogen. From statistical analyses, our results suggest that hydrogen reduces stacking fault energy, which likely impacts deformation mechanisms of Fe–Ni–Cr austenitic stainless steels when exposed to hydrogen environments. We then perform validation MD simulation tests to show that hydrogen indeed statistically increases the stacking fault widths due to statistically reduced stacking fault energies.     

Permeability,solubility and diffusivity of hydrogen isotopes in stainless steels at high gas pressures

In this report, we provide a framework for describing the permeability, solubility and diffusivity of hydrogen and its isotopes in austenitic stainless steels at temperatures and high gas pressures of engineering interest for hydrogen storage and distribution infrastructure. We demonstrate the importance of using the real gas behavior for modeling permeation and dissolution of hydrogen under these conditions. A simple one-parameter equation of state (the Abel–Noble equation of state) is shown to capture the real gas behavior of hydrogen and its isotopes for pressures less than 200 MPa and temperatures between 223 and 423 K. We use the literature on hydrogen transport in austenitic stainless steels to provide general guidance on and clarification of test procedures, and to provide recommendations for appropriate permeability, diffusivity and solubility relationships for austenitic stainless steels. Hydrogen precharging and concentration measurements for a variety of austenitic stainless steels are described and used to generate more accurate solubility and diffusivity relationships.     

The mechanism of enhanced resistance to the hydrogen delayed fracture in Al-added Fe–18Mn–0.6C twinning-induced plasticity steels

High Mn twinning-induced plasticity (TWIP) steels are attractive for high performance applications owing to their extraordinary ductility at a giga-graded tensile strength level. Hydrogen delayed fracture (HDF) came to the fore as a key issue to be solved for the application of these steels. Although it was found that Al addition improved the resistance to HDF, the reason was unclear. Therefore, in this study, the fracture surfaces of annealed and hydrogen-charged TWIP steels with different Al contents were examined after slow strain rate tensile tests. Diffusible hydrogen was measured by thermal desorption analysis. It found that the strong resistance to HDF was due to an α-Al₂O₃ layer formed below the (Fe_0.8Mn_0.2)O layer during the hydrogen charging in an aqueous solution prevented the hydrogen to permeate into specimens from the surface.     

Stresses controllable analysis and optimal design of unique high pressure vessel applied in hydrogen charge station

High pressure hydrogen storage vessels are the key equipment in hydrogen charge stations. Hydrogen environment embrittlement (HEE) is always the associated problem that is inescapable and difficult to be solved completely. In order to decrease the harmfulness of HEE, a unique flat steel ribbon wound pressure vessel (FSRWPV) is designed, whose inner shell material is austenitic stainless steels 0Cr18Ni9 (304) and the steel ribbon material is 16MnR (SA516Gr70). The residual stresses in FSRWPV are analyzed and a stress controlling model is put forward. Through this model, the stress distribution in the FSRWPV wall can be controlled by adjusting the pretension in flat steel ribbons. After optimal designing, the stresses in flat steel ribbon layers are uniform, and that in the inner shell is low or negative. This kind of stress distribution can effectively prevent HEE and stress corrosion cracking (SCC), therefore the FSRWPV has good properties of bearing HEE and SCC. Furthermore, as flat steel ribbon layers are a discrete structure, the online monitoring of FSRWPVs can be conveniently realized, so they have performance of “leak only no bursting”. At the end, an applied example of high pressure hydrogen FSRWPV is given.     

Origin of deformation twins and their influence on hydrogen embrittlement in cold-rolled austenitic stainless steel

The effect of cold rolling on hydrogen embrittlement in stable 18Cr–1Mn–11Ni-0.15 N austenitic stainless steels was investigated. Alloy plates were cold-rolled to 15% or 30% reduction, then pre-charged with hydrogen and subjected to tensile testing with slow strain rate. Hydrogen-induced degradation of tensile elongation became increasingly severe with the increase in the degree of cold rolling. During cold rolling, deformation twins with various orientations were actively generated, and twins with specific orientations were vulnerable to hydrogen-induced cracking. Cold rolling also increased the density of defects, and thereby facilitated penetration of hydrogen into the steels. The combination of cracks generated at the twin boundaries, and the promoted hydrogen diffusion caused severe hydrogen embrittlement in the cold-rolled steels.     

Effect of grain size on hydrogen embrittlement in stable austenitic high-Mn TWIP and high-N stainless steels

Two stable austenitic steels, 20Cr-11Ni-5Mn-0.3N (wt%) stainless steel (STS) and 18Mn-1.5Al-0.6C (wt%) twinning-induced plasticity steel (TWIP), were investigated to understand the effect of grain size on hydrogen embrittlement (HE). Grain refinement promoted HE in the STS but suppressed HE in the TWIP. These opposite effects occurred because the steel composition affected deformation mechanism. Cr-N pair enhanced short-range ordering (SRO) in STS, which promoted planar slip and delayed mechanical twinning. In contrast, TWIP exhibited mechanical twinning which was more active in coarser grains. Final dislocation density after tensile deformation was increased by grain refinement in STS, but was decreased in TWIP. The damaging effects of hydrogen on strain energy at interfaces and on interfacial bonding strength were controlled by dislocation density; therefore, increase in dislocation density led to increase in susceptibility to HE.     

Phase transformations and microstructure evolutions during depressurization of hydrogenated Fe–Mn–Si–Cr alloy

Hydride formation and associated phase transformations have been extensively studied in pure Fe. However, the understanding of hydrogenation in Fe-based alloy systems is still lacking. Such an investigation is particularly important in the case of austenitic (face-centered cubic) steels given that hydrogen has been reported to alter the austenite phase stability. In the current work, we investigate the phase transformations associated with depressurization of non-hydrogenated and hydrogenated Fe–Mn–Si–Cr alloy (FMS) (Fe-28.84Mn-7.04Cr-6.14Si, in mass %) using in-situ x-ray diffraction technique. Additionally, we study the change in microstructure using electron backscatter diffraction (EBSD) and electron channeling contrast imagining (ECCI).     

Hydrogen environment embrittlement of orbital welded austenitic stainless steels at −50 °C

Different stainless steels were TIG orbital welded resulting in δ-ferrite contents up to 5% in the weld seam. Tensile specimens tested in He atmosphere did fracture at the fusion line/heat affected zone (FL/HAZ), which is the typical failure mode for welded structures. In contrast, all specimens (except the one made of 1.4301) tested in H₂ did not fracture in the FL/HAZ but in the base material. These results clearly show that for the tests performed here δ-ferrite contents up to 5% did not enhance susceptibility to HEE compared to the base material.     

Development of a stable high-aluminum austenitic stainless steel for hydrogen applications

A novel high-aluminum austenitic stainless steel has been produced in the laboratory with the aim of developing a lean-alloyed material with a high resistance to hydrogen environment embrittlement. The susceptibility to hydrogen environment embrittlement was evaluated by means of tensile tests at a slow strain rate in pure hydrogen gas at a pressure of 40 MPa and a temperature of −50 °C. Under these conditions, the yield strength, tensile strength and elongation to rupture are not affected by hydrogen in comparison to companion tests carried out in air. Moreover, a very high ductility in hydrogen is evidenced by a reduction of area of 70% in the high-pressure and low-temperature hydrogen environment. The lean degree of alloying is reflected in the molybdenum-free character of the material and a nickel content of 8.0 wt.%. With regard to the alloy concept, a combination of high-carbon, high-manganese, and high-aluminum contents confer an extremely high stability against the formation of strain-induced martensite. This aspect was investigated by means of in-situ magnetic measurements and ex-situ X-ray diffraction. The overall performance of the novel alloy was compared with two reference materials, 304L and 316L austenitic stainless steels, both industrially produced. Its capability of maintaining a fully austenitic structure during tensile testing has been identified as a key aspect to avoid hydrogen environment embrittlement.     

Hydrogen transport in solution-treated and pre-strained austenitic stainless steels and its role in hydrogen-enhanced fatigue crack growth

Hydrogen solubility and diffusion in Type 304, 316L and 310S austenitic stainless steels exposed to high-pressure hydrogen gas has been investigated. The effects of absorbed hydrogen and strain-induced martensite on fatigue crack growth behaviour of the former two steels have also been measured. In the pressure range 10–84 MPa, the hydrogen permeation of the stainless steels could be successfully quantified using Sieverts' law modified by using hydrogen fugacity and Fick's law. For the austenitic stainless steels, hydrogen diffusivity was enhanced with an increase in strain-induced martensite. The introduction of dislocation and other lattice defects by pre-straining increased the hydrogen concentration of the austenite, without affecting diffusivity. It has been shown that the coupled effect of strain-induced martensite and exposure to hydrogen increased the growth rate of fatigue cracks.     

Impact of chemical inhomogeneities on local material properties and hydrogen environment embrittlement in AISI 304L steels

This study investigated the influence of segregations on hydrogen environment embrittlement (HEE) of AISI 304L type austenitic stainless steels. The microstructure of tensile specimens, that were fabricated from commercially available AISI 304L steels and tested by means of small strain-rate tensile tests in air as well as hydrogen gas at room temperature, was investigated by means of combined EDS and EBSD measurements. It was shown that two different austenitic stainless steels having the same nominal alloy composition can exhibit different susceptibilities to HEE due to segregation effects resulting from different production routes (continuous casting/electroslag remelting). Local segregation-related variations of the austenite stability were evaluated by thermodynamic and empirical calculations. The alloying element Ni exhibits pronounced segregation bands parallel to the rolling direction of the material, which strongly influences the local austenite stability. The latter was revealed by generating and evaluating two-dimensional distribution maps for the austenite stability. The formation of deformation-induced martensite was shown to be restricted to segregation bands with a low Ni content. Furthermore, it was shown that the formation of hydrogen induced surface cracks is strongly coupled with the existence of surface regions of low Ni content and accordingly low austenite stability. In addition, the growth behavior of hydrogen-induced cracks was linked to the segregation-related local austenite stability.     

Characterization of high strength and high toughness Ni–Mo–Cr low alloy steels for nuclear application

The reactor pressure vessels of PWRs have mostly been made of SA508 Grade 3 (Class 1) low alloy steels which have revealed moderate mechanical properties and a moderate radiation resistance for a 40 or 60 year operation. The specified minimum yield strength of the material is 345 MPa with a ductile–brittle transition temperature of about 0 °C. While other materials, most of which are non-ferrous alloys or high alloyed steels for a higher temperature application, are being developed for the Generation-4 reactors, low alloy steels with a higher strength and toughness can help to increase the safety and economy of the advanced PWR systems which will be launched in the near future. The ASME specification for SA508 Grade 4N provides a way to increase both the strength and toughness by a chemistry modification, especially by increasing the Ni and Cr contents. However, a higher strength steel has a deficiency due to a lack of operating data for nuclear power plants. In this study, experimental heats of SA508 Grade 4N steels with different chemical compositions were characterized mechanically. The preliminary results for an irradiation embrittlement and the HAZ properties are discussed in addition to their superior baseline properties.     

Effect of plasma nitriding on behavior of austenitic stainless steel 304L bipolar plate in proton exchange membrane fuel cell

A dense and supersaturated nitrogen layer with higher conductivity is obtained on the surface of austenitic stainless steel 304L by the low temperature plasma nitriding. The effect of plasma nitriding on the corrosion behavior and interfacial contact resistance (ICR) for the austenitic stainless steel 304L was investigated in 0.05 M H₂SO₄ + 2 ppm F⁻ simulating proton exchange membrane fuel cell (PEMFC) environment using electrochemical and electric resistance measurements. The experiment results show that the stable passive film is formed after the potentiostatic polarization at the specified anodic or cathodic potentials under PEMFC operation condition, and the plasma nitriding improves slightly the corrosion resistance and decreases markedly the ICR of 304L. The ICR of the plasma nitrided 304L increases after the potentiostatic polarizations for 4 h, and lower than 100 mΩ cm² at the compaction force of 150 N cm⁻².