Optimization of TiH2 content for fast and efficient hydrogen cycling of MgH2-TiH2 nanocomposites

Magnesium hydride is extensively examined as a hydrogen store due to its high hydrogen content and low cost. However, high thermodynamic stability and sluggish kinetics hinder its practical application. To overcome this last drawback, different Ti amounts (y = 0, 0.025, 0.05, 0.1, 0.2 and 0.3) were added to magnesium to form (1-y)MgH₂+yTiH₂ nanocomposites (NC) by reactive ball milling under hydrogen gas. Thermodynamic stability of the MgH₂ phase in NCs was determined using a manometric Sieverts rig. Reversible hydrogen capacity and reaction kinetics were determined at 573 K over 20 sorption cycles under a limited reaction time of 15 min. On increasing Ti amount, reaction kinetics are enhanced both in absorption and desorption leading to a higher reversibility for hydrogen storage with the MgH₂ phase. However, titanium increases the molar weight of NCs and forms irreversible titanium hydride. The highest reversible capacity (4.9 wt% H) was obtained for the lowest here studied TiH₂ content (y = 0.025).     

Synthesis of BaFe12O19 by solid state method and its effect on hydrogen storage properties of MgH2

Previous studies have shown that ferrites give a positive effect in improving the hydrogen sorption properties of magnesium hydride (MgH₂). In this study, another ferrite, i.e., BaFe₁₂O₁₉, has been successfully synthesised via the solid state method, and it was milled with MgH₂ to enhance the sorption kinetics. The result showed that the MgH₂ + 10 wt% BaFe₁₂O₁₉ sample started to release hydrogen at about 270 °C which is about 70 °C lower than the as-milled MgH₂. The doped sample was able to absorb hydrogen for 4.3 wt% in 10 min at 150 °C, while as-milled MgH₂ only absorbed 3.5 wt% of hydrogen under similar conditions. The desorption kinetic results showed that the doped sample released about 3.5 wt% of hydrogen in 15 min at 320 °C, while the as-milled MgH₂ only released about 1.5 wt% of hydrogen. From the Kissinger plot, the apparent activation energy of the BaFe₁₂O₁₉-doped MgH₂ sample was 115 kJ/mol which was lower than the milled MgH₂ (141 kJ/mol)_. Further analyses demonstrated that MgO, Fe and Ba or Ba-containing contribute to the improvement by serving as active species, thus enhancing the MgH₂ for hydrogen storage.     

Comparisons between MgH2- and LiH-containing systems for hydrogen storage applications

The present study compares the dehydrogenation kinetics of (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ and (_LiNH2+LiH)$({\mathrm{LiNH}}_2+\mathrm{LiH})$ systems and their vulnerabilities to the NH₃ emission problem. The (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ and (_LiNH2+LiH)$({\mathrm{LiNH}}_2+\mathrm{LiH})$ mixtures with different degrees of mechanical activation are investigated in order to evaluate the effect of mechanical activation on the dehydrogenation kinetics and NH₃ emission rate. The activation energy for dehydrogenation, the phase changes at different stages of dehydrogenation, and the level of NH₃ emission during the dehydrogenation process are studied. It is found that the (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ mixture has a higher rate for hydrogen release, slower rate for approaching a certain percentage of its equilibrium pressure, higher activation energy, and more NH₃ emission than the (_LiNH2+LiH)$({\mathrm{LiNH}}_2+\mathrm{LiH})$ mixture. On the basis of the phenomena observed, the reaction mechanism for the dehydrogenation of the (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ system has been proposed for the first time. Approaches for further improving the hydrogen storage behavior of the (2_LiNH2+_MgH2)$(2{\mathrm{LiNH}}_2+{\mathrm{MgH}}_2)$ system are discussed in light of the newly proposed reaction mechanism.     

Fundamental environmental reactivity testing and analysis of the hydrogen storage material 2LiBH4·MgH2

While the storage of hydrogen for portable and stationary applications is regarded as critical in bringing PEM fuel cells to commercial acceptance, little is known of the environmental exposure risks posed in utilizing condensed phase chemical storage options as in complex hydrides. It is thus important to understand the effect of environmental exposure of metal hydrides in the case of accident scenarios. Simulated tests were performed following the United Nations standards to test for flammability and water reactivity in air for a destabilized lithium borohydride and magnesium hydride system in a 2 to 1 molar ratio respectively. It was determined that the mixture acted similarly to the parent, lithium borohydride, but at slower rate of reaction seen in magnesium hydride. To quantify environmental exposure kinetics, isothermal calorimetry was utilized to measure the enthalpy of reaction as a function of exposure time to dry and humid air, and liquid water. The reaction with liquid water was found to increase the heat flow significantly during exposure compared to exposure in dry or humid air environments. Calorimetric results showed the maximum normalized heat flow of the fully charged material was 6 mW/mg under liquid phase hydrolysis; and 14 mW/mg for the fully discharged material also occurring under liquid phase hydrolysis conditions.     

Improvement of hydrogen storage properties in MgH2 catalysed by K2NbF7

The catalytic effects of K₂NbF₇ on the hydrogen storage properties of MgH₂ have been studied for the first time. MgH₂ + 5 wt% K₂NbF₇ has reduced the onset dehydrogenation temperature to 255 °C, which is 75 °C lower than the as-milled MgH₂. For the rehydrogenation kinetic, at 150 °C, MgH₂ + 5 wt% K₂NbF₇ absorbs 4.7 wt% of hydrogen in 30 min whereas the as-milled MgH₂ only absorbs 0.7 wt% of hydrogen under similar condition. For the dehydrogenation kinetic, at 320 °C, the MgH₂ + 5 wt% K₂NbF₇ is able to release 5.2 wt% of hydrogen in 5.6 min as compared to 0.3 wt% by the as-milled MgH₂ under similar condition. Comparatively, the E_a value of MgH₂ + 5 wt% K₂NbF₇ is 96.3 kJ/mol, which is 39 kJ/mol lower compared to the as-milled MgH₂. The MgF₂, the KH and the Nb that are found after the heating process are believed to be the active species that have improved the system properties. It is concluded that the K₂NbF₇ is a good catalyst to improve the hydrogen storage properties of MgH₂.     

NiB nanoparticles: A new nickel-based catalyst for hydrogen storage properties of MgH2

In this paper, amorphous NiB nanoparticles were fabricated by chemical reduction method and the effect of NiB nanoparticles on hydrogen desorption properties of MgH₂ was investigated. Measurements using temperature-programmed desorption system (TPD) and volumetric pressure–composition isotherm (PCI) revealed that both the desorption temperature and desorption kinetics have been improved by adding 10 wt% amorphous NiB. For example, the MgH₂–10 wt%NiB mixture started to release hydrogen at 180 °C, whereas it had to heat up to 300 °C to release hydrogen for the pure MgH₂. In addition, a hydrogen desorption capacity of 6.0wt% was reached within 10 min at 300 °C for the MgH₂–10 wt%NiB mixture, in contrast, even after 120 min only 2.0 wt% hydrogen was desorbed for pure MgH₂ under the same conditions. An activation energy of 59.7 kJ/mol for the MgH₂/NiB composite has been obtained from the desorption data, which exhibits an enhanced kinetics possibly due to the additives reduced the barrier and lowered the driving forces for nucleation. Further cyclic kinetics investigation using high-pressure differential scanning calorimetry technique (HP-DSC) indicated that the composite had good cycle stability.     

Effects of CNTs on the hydrogen storage properties of MgH2 and MgH2-BCC composite

MgH₂ with 10 wt.% Ti_0.4Mn_0.22Cr_0.1V_0.28 alloy (termed the BCC alloy for its body centred cubic structure) and 5 wt.% carbon nanotubes (CNTs) were prepared by planetary ball milling, and its hydrogen storage properties were compared with those of the pure MgH₂ and the binary mixture of MgH₂ and the BCC alloy. The sample with CNTs showed considerable improvement in hydrogen sorption properties. Its temperature of desorption was 125 °C lower than for the pure sample and 59 °C lower than for the binary mixture. In addition, the gravimetric capacity of the ternary sample was 6 wt.% at 300 °C and 5.6 wt.% at 250 °C, and it absorbed 90% of this amount at 150 s and 516 s at 300 °C and 250 °C, respectively. It can be hypothesised from the results that the BCC alloy assists the dissociation of hydrogen molecules into hydrogen atoms and also promotes hydrogen pumping into the Mg/BCC interfaces, while the CNTs facilitate access of H-atoms into the interior of Mg grains.     

Synergistic catalytic effect of SrTiO3 and Ni on the hydrogen storage properties of MgH2

Study on the synergistic catalytic effect of the SrTiO₃ and Ni on the improvement of the hydrogen storage properties of the MgH₂ system has been carried out. The composites have been prepared using ball milling method and comparisons on the hydrogen storage properties of the MgH₂ – Ni and MgH₂ – SrTiO₃ composites have been presented. The MgH₂ – 10 wt% SrTiO₃ – 5 wt% Ni composite is found to has a decomposition temperature of 260 °C with a total decomposition capacity of 6 wt% of hydrogen. The composite is able to absorb 6.1 wt% of hydrogen in 1.3 min (320 °C, 27 atm of hydrogen). At 150 °C, the composite is able to absorb 2.9 wt% of hydrogen in 10 min under the pressure of 27 atm of hydrogen. The composite has successfully released 6.1 wt% of hydrogen in 13.1 min with a total dehydrogenation of 6.6 wt% of hydrogen (320 °C). The apparent activation energy, E_a, for decomposition of SrTiO₃-doped MgH₂ reduced from 109.0 kJ/mol to 98.6 kJ/mol after the addition of 5 wt% Ni. The formation of Mg₂Ni and Mg₂NiH₄ as the active species help to boost the performance of the hydrogen storage properties of the MgH₂ system. Observation of the scanning electron microscopy images suggested the catalytic role of the SrTiO₃ additive is based on the modification of composite microstructure.     

Changes of hydrogen storage properties of MgH2 induced by heavy ion irradiation

In order to understand the influence of defect zones on desorption behavior of _MgH2${\mathrm{MgH}}_2$, Xe 120 keV ion irradiation of this material has been performed. DSC, SEM measurements, and SRIM calculations have been used to characterize induced modifications and its influence on the hydrogen desorption behavior of _MgH2${\mathrm{MgH}}_2$. We have demonstrated that the near-surface area of _MgH2${\mathrm{MgH}}_2$ plays the crucial role in hydrogen desorption kinetics. DSC analysis provides clear picture of vacancies influence on H diffusion and desorption in _MgH2${\mathrm{MgH}}_2$, and points out that there is possibility to control the thermodynamic parameters by controlled ion bombardment.     

Effects of SiC nanoparticles with and without Ni on the hydrogen storage properties of MgH2

In this work, MgH₂–SiC–Ni was prepared by magneto-mechanical milling in hydrogen atmosphere. Scanning electron microscope mapping images showed a homogeneous dispersion of both Ni and SiC among MgH₂ particles. Based on the differential scanning calorimetry traces, the temperature of desorption is reduced by doping MgH₂ with SiC and Ni. Hydrogen absorption/desorption behaviour of the samples was investigated by Sievert's method at 300 °C, and the results showed that both capacity and kinetics were improved by adding SiC and Ni. The hydrogen desorption kinetic investigation indicated that for pure MgH₂, the rate-determining step is surface controlled and recombination, while for the MgH₂–SiC–Ni sample it is controlled as described by the Johnson–Mehl–Avrami 3D model (JMA 3D).     

A comparative study of the role of additive in the MgH2 vs. the LiBH4-MgH2 hydrogen storage system

The objective of the present work is the comparative study of the behaviour of the Nb- and Ti-based additives in the MgH₂ single hydride and the MgH₂ + 2LiBH₄ reactive hydride composite. The selected additives have been previously demonstrated to significantly improve the sorption reaction kinetics in the corresponding materials. X-Ray Diffraction (XRD), X-Ray Absorption Spectroscopy (XAS), X-Ray Photoelectron Spectroscopy (XPS) and Electron Microscopy (TEM) analysis were carried out for the milled and cycled samples in absence or presence of the additives. It has been shown that although the evolution of the oxidation state for both Nb- and Ti-species are similar in both systems, the Nb additive is performing its activity at the surface while the Ti active species migrate to the bulk. The Nb-based additive is forming pathways that facilitate the diffusion of hydrogen through the diffusion barriers both in desorption and absorption. For the Ti-based additive in the reactive hydride composite, the active species are working in the bulk, enhancing the heterogeneous nucleation of MgB₂ phases during desorption and producing a distinct grain refinement that favours both sorption kinetics. The results are discussed in regards to possible kinetic models for both systems.     

Influence of K2TiF6 additive on the hydrogen sorption properties of MgH2

In this study, the hydrogen storage properties of MgH₂ with the addition of K₂TiF₆ were investigated for the first time. The temperature-programmed desorption results showed that the addition of 10 wt% K₂TiF₆ to the MgH₂ exhibited a lower onset desorption temperature of 245 °C, which was a decrease of about 105 °C and 205 °C compared with the as-milled and as-received MgH₂, respectively. The dehydrogenation and rehydrogenation kinetics of 10 wt% K₂TiF₆-doped MgH₂ were also significantly improved compared to the un-doped MgH₂. The results of the Arrhenius plot showed that the activation energy for the hydrogen desorption of MgH₂ was reduced from 164 kJ/mol to 132 kJ/mol after the addition of 10 wt% K₂TiF₆. Meanwhile, the X-ray diffraction analysis showed the formation of a new phase of potassium hydride and titanium hydride together with magnesium fluoride and titanium in the doped MgH₂ after the dehydrogenation and rehydrogenation process. It is reasonable to conclude that the K₂TiF₆ additive doped with MgH₂ played a catalytic role through the formation of active species of KH, TiH₂, MgF₂ and Ti during the ball milling or heating process. It is therefore proposed that this newly developed product works as a real catalyst for improving the hydrogen sorption properties of MgH₂.     

Direct synthesis of MgH2 nanofibers at different hydrogen pressures

This paper describes the direct synthesis of magnesium hydride (MgH₂) nanofibers by hydriding chemical vapor deposition (HCVD), in which the effect of hydrogen pressure on the production rate, the composition and the shape of products obtained were examined by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and Brunauer–Emmett–Teller (BET). The XRD patterns showed that the main product in each case was MgH₂; in particular, the products formed at 2, 3 and 4 MPa were highly pure. In contrast, at a hydrogen pressure of 1 MPa, unhydrided Mg was deposited along with MgH₂. The SEM images also revealed orientation of the as-deposited products; higher pressures of 3 and 4 MPa caused the formation of straight and curved nanofibers, and lower ones of 1 and 2 MPa, highly curved nanofibers and nanorods with a few straight nanofibers. With pressurizing hydrogen, not only the BET specific surface areas of the products but also the production rate increased. The results also appealed that HCVD could control the shape/size of MgH₂ nanofibers by changing the pressure via only a single operation.     

Enhanced hydrogen storage properties of 4MgH2 + LiAlH4 composite system by doping with Fe2O3 nanopowder

In this paper, the hydrogen storage properties and reaction mechanism of the 4MgH₂ + LiAlH₄ composite system with the addition of Fe₂O₃ nanopowder were investigated. Temperature-programmed-desorption results show that the addition of 5 wt.% Fe₂O₃ to the 4MgH₂ + LiAlH₄ composite system improves the onset desorption temperature to 95 °C and 270 °C for the first two dehydrogenation stage, which is lower 40 °C and 10 °C than the undoped composite. The dehydrogenation and rehydrogenation kinetics of 5 wt.% Fe₂O₃-doped 4MgH₂ + LiAlH₄ composite were also improved significantly as compared to the undoped composite. Differential scanning calorimetry measurements indicate that the enthalpy change in the 4MgH₂–LiAlH₄ composite system was unaffected by the addition of Fe₂O₃ nanopowder. The Kissinger analysis demonstrated that the apparent activation energy of the 4MgH₂ + LiAlH₄ composite (125.6 kJ/mol) was reduced to 117.1 kJ/mol after doping with 5 wt.% Fe₂O₃. Meanwhile, the X-ray diffraction analysis shows the formation of a new phase of Li₂Fe₃O₄ in the doped composite after the dehydrogenation and rehydrogenation process. It is believed that Li₂Fe₃O₄ acts as an actual catalyst in the 4MgH₂ + LiAlH₄ + 5 wt.% Fe₂O₃ composite which may promote the interaction of MgH₂ and LiAlH₄ and thus accelerate the hydrogen sorption performance of the MgH₂ + LiAlH₄ composite system.     

High pressure DSC study of hydrogen sorption in MgH2/graphite mixtures: Effects of sintering and oxidation

Hydrogen absorption and desorption properties of ball milled Mg and Mg/graphite materials were analyzed by high pressure differential scanning calorimetry. The influence on hydrogen sorption kinetics of different graphite distribution, oxygen poisoning and magnesium sintering was studied. The Mg/graphite mixture with graphite distributed in the bulk showed better kinetics than the material with graphite located on the surface and Mg without additive. The effect of sintering and oxygen poisoning was a progressive storage capacity loss, due to a kinetic limitation in the case of sintering, and due to irreversible magnesium oxidation in the case of poisoning. The mixtures with graphite exhibited more resistance toward oxygen contamination, particularly in the case where graphite was primarily located on the surface compared to the material with graphite well dispersed in the bulk.     

Zinc substituted MgH2 - a potential material for hydrogen storage applications

The search for efficient materials for onboard hydrogen storage applications is an emerging research field. Using density functional calculations, we demonstrate Zn substituted MgH₂ as a potential material for hydrogen storage. We predicted the ground state crystal structure of ZnH₂ which is found to be Pna2₁ (orthorhombic) structure with meta-stable behavior. The structural phase stability and phase transition of Mg_1−xZn_xH₂ systems have been analyzed. The H site energy of Mg_1−xZn_xH₂ systems is calculated to understand the hydrogen desorption process. Our calculations suggest that Zn substitution reduces the stability of MgH₂, thereby it may reduce the decomposition temperature of MgH₂. The band structure and density of states calculations reveal that the Mg_1−xZn_xH₂ systems are insulators. The chemical bonding behavior of Mg_1−xZn_xH₂ systems is established as iono-covalent in nature. Moreover, Zn substitution in MgH₂ induces disproportionate MgH bonds which could also contribute the reduction in the decomposition temperature as well as H sorption kinetics.     

Catalytic effect of melt-spun Ni3FeMn alloy on hydrogen desorption properties of nanocrystalline MgH2 synthesized by mechanical alloying

To improve hydrogen desorption properties of magnesium hydride, a composite material with composition of MgH₂-5 at% Ni₃FeMn has been prepared by co-milling MgH₂ powder with Ni₃FeMn alloy either in the form of as-cast (sample A) or melt-spun ribbon (sample B). The study has shown that the addition of Ni₃FeMn alloy to magnesium hydride can yield a finer particle size after mechanical alloying (MA). As a consequence, the desorption temperature of mechanically activated MgH₂ for 30 h has decreased from 319 °C to 307 °C for sample A and to 290 °C for sample B. Furthermore, some favorable effects of Ni₃FeMn alloy on hydrogen desorption kinetics have been observed. Further improvement in the hydrogen desorption of melt-spun containing composite can be related to higher hardness value of the melt-spun powder compared to the as-cast alloy, and probably a more homogeneous distribution of the alloyed elements.     

Hydrogen desorption properties of MgH2-TiCr1.2Fe0.6 nanocomposite prepared by high-energy mechanical alloying

In the present work, high-energy mechanical alloying (MA) was employed to synthesize a nanostructured magnesium-based composite for hydrogen storage. The preparation of the composite material with composition of MgH₂-5 at% (TiCr_1.2Fe_0.6) was performed by co-milling of commercial available MgH₂ powder with the body-centered cubic (bcc) alloy either in the form of Ti-Cr-Fe powder mixture with the proper mass fraction (sample A) or prealloyed TiCr_1.2Fe_0.6 powder (sample B). The prealloyed powder with an average crystallite size of 14 nm and particle size of 384 nm was prepared by the mechanical alloying process. It is shown that the addition of the Ti-based bcc alloy to magnesium hydride yields a finer particle size and grain structure after mechanical alloying. As a result, the desorption temperature of mechanically activated MgH₂ for 4 h decreased from 327 °C to 262 °C for sample A and 241 °C for sample B. A high dehydrogenation capacity (∼5 wt%) at 300 °C is also obtained. The effect of the Ti-based alloy on improvement of the dehydrogenation is discussed.     

Effects of SnO2 on hydrogen desorption of MgH2

The hydrogen desorption properties of Magnesium Hydride (MgH₂) ball milled with cassiterite (SnO₂) have been investigated by X-ray powder diffraction and thermal analysis. Milling of pure MgH₂ leads to a reduction of the desorption temperature (up to 60 K) and of the activation energy, but also to a reduction of the quantity of desorbed hydrogen, referred to the total MgH₂ present, from 7.8 down to 4.4 wt%. SnO₂ addition preserves the beneficial effects of grinding on the desorption kinetics and limits the decrease of desorbed hydrogen. Best tradeoff – activation energy lowered from 175 to 148 kJ/mol and desorbed hydrogen, referred to the total MgH₂ present, lowered from 7.8 to 6.8 wt% – was obtained by co-milling MgH₂ with 20 wt% SnO₂.     

Hydrogen sorption in MgH2-based composites: The role of Ni and LiBH4 additives

In the present work we investigate the hydrogen sorption properties of composites in the MgH₂–Ni, MgH₂–Ni–LiH and MgH₂–Ni–LiBH₄ systems and analyze why Ni addition improve hydrogen sorption rates while LiBH₄ enhance the hydrogen storage capacity. Although all composites with Ni addition showed significantly improved hydrogen storage kinetics compared with the pure MgH₂, the fastest hydrogen sorption kinetics is obtained for Ni-doped MgH₂. The formation of Mg₂Ni/Mg₂NiH₄ in Ni-doped MgH₂ composite and its microstructure allows to uptake 5.0 wt% of hydrogen in 25 s and to release it in 8 min at 275 °C. In the MgH₂–Ni–LiBH₄ composite, decomposition of LiBH₄ occurs during the first dehydriding leading to the formation of diborane, which has a Ni catalyst poison effect via the formation of a passivating boron layer. A combination of FTIR, XRD and volumetric measurements demonstrate that the formation of MgNi₃B₂ in the MgH₂–Ni–LiBH₄ composite happens in the subsequent hydriding cycle from the reaction between Mg₂Ni/Mg₂NiH₄ and B. Activation energy analysis demonstrates that the presence of Ni particles has a catalytic effect in MgH₂–Ni and MgH₂–Ni–LiH systems, but it is practically nullified by the addition of LiBH₄. The beneficial role of LiBH₄ on the hydrogen storage capacity of the MgH₂–Ni–LiBH₄ composite is discussed.