Characterization of single-wall carbon nanotubes by N2 adsorption

N₂ adsorption isotherms at 77 K of single-wall carbon nanotubes (SWNTs), multi-wall carbon nanotubes (MWNTs), and mixtures of these carbon nanotubes (CNTs) were analyzed for differences in their pore size distributions (PSDs). The PSDs, calculated in the microporous region by the Horvath–Kawazoe method and in the mesoporous region by the BJH method, are in agreement with the structures of both types of CNTs deduced from high-resolution transmission electron microscopy. A characteristic peak in the microporous region in the PSD of SWNTs is not present in the PSDs of MWNTs and impurities such as amorphous carbon, metal residues of catalysts, etc. The evaluation of this peak is proposed as a convenient tool for the quantitative characterization of SWNT purity in carbon nanotube-containing samples.     

High growth of SWNTs and MWNTs from C2H2 decomposition over Co-Mo/MgO catalysts

A series of MgO supported catalysts having Co and Mo metals 5-40 wt.% in a ratio of 1:1 was prepared by impregnation method. Carbon nanotubes (CNTs) were grown over the catalysts by decomposition of C₂H₂ at 800 °C for 30 min. It was found that 5 and 10 wt.% Co-Mo/MgO catalysts produced single-wall nanotubes (SWNTs), whereas 20, 30 and 40 wt.% Co-Mo/MgO catalysts produced multi-wall nanotubes (MWNTs). The catalyst Mo/MgO was inactive in growing CNTs. In Co-Mo/MgO catalysts, however Mo generated a favorable environment to grow SWNTs. The growth of SWNTs was strongly dependent on the formation of small clusters of cobalt, which may generate from the decomposition of CoMoO₄ species during the nanotube growth. MWNTs were produced over comparatively larger cobalt clusters generated from Co₃O₄ phase during the nanotube growth stage. The yields of SWNTs were about 6% and 27% over 5 and 10 wt.% Co-Mo/MgO catalysts, respectively. MWNTs yield (576%) was observed over 40 wt.% Co-Mo/MgO catalyst. Carbon yield (%) highly varied with acetylene concentration.     

Rutile TiO2-modified multi-wall carbon nanotubes in TiO2 film electrodes for dye-sensitized solar cells

The beneficial influence of incorporation of acid-treated and rutile TiO₂ (r-TiO₂)-modified multi-wall carbon nanotubes (MWNTs) in TiO₂ films on photocurrent–voltage characteristics of dye-sensitized solar cells (DSSCs) was studied. Two different routes were adopted for the modification of acid-treated MWNTs (a-MWNTs) with r-TiO₂. The films and MWNTs were characterized by electron microscopy, energy dispersive X-ray spectroscopy, XRD and Raman spectroscopy. In the case of incorporation of a-MWNTs with r-TiO₂ modification, short-circuit photocurrent (J _sc) of the pertinent DSSC increased by 35% compared with that of a cell with bare TiO₂ film. The open-circuit voltage remained almost the same for all cases. The enhanced J _sc is explained by the increased surface area of the film, enhanced cluster formation of TiO₂ particles around a-MWNTs, and improved interconnectivity of TiO₂ particles in the presence of a-MWNTs.     

Direct synthesis of mesoporous silicalite-1 supported TiO2–ZrO2 for the dehydrogenation of EB to styrene with CO2

Direct synthesis route was developed to support TiO₂–ZrO₂ binary metal oxide onto the carbon templated mesoporous silicalite-1 (CS-1). Metal hydroxide modified carbon particles could play a role as hard template and simultaneously support metal components on the mesopores during the crystallization of zeolites. Such supported TiO₂–ZrO₂ binary metal oxides (TZ/CS-1) showed better resistance to deactivation in the oxidative dehydrogenation of ethylbenzene (ODHEB) in the presence of CO₂. These catalysts were found to be active, selective and catalytically stable (10 h of time-on-stream) at 600 °C for the dehydrogenation of ethylbenzene (EB) to styrene (Sty).     

Synthesis of carbon nanotubes by pyrolysis of solid Ni(dmg)2

We describe the high yield synthesis of multi-walled carbon nanotubes (MWCNTs) and the determination of the optimum production conditions. The method involves the catalytic pyrolysis of solid Ni(dmg)₂ under an Ar atmosphere. The obtained materials were characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis, high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Raman spectroscopy and thermogravimetry analysis (TGA). The data revealed the formation of MWCNTs surrounded by a varying quantity of byproducts such as amorphous carbon and metallic particles, depending mainly on the reaction temperature. Pyrolysis of Ni(dmg)₂ at 900 °C results in the production of nanotube material with the highest degree of crystallinity.     

Experimental study on CO2 hydrate formation in the presence of TiO2, SiO2, MWNTs nanoparticles

ABSTRACT

A series of experiments on CO₂ hydrate formation were carried out in the presence of titanium dioxide (TiO₂), silicon dioxide (SiO₂), multi-walled carbon nanotubes (MWNTs) nanoparticles. The effects of these nanoparticles on induction time, final gas consumption, and gas storage capacity have been investigated at the temperature of 274.15 K and the initial pressure of 5.0 MPa.g. The induction time of CO₂ hydrate formation was remarkably shortened to 12.5 min in the presence of 0.005 wt% MWNTs nanoparticles. The high thermal conductivity and heat capacity of MWNTs nanoparticles presented better heat transfer, and large surface area provided more suitable sites for heterogeneous nucleation of CO₂ hydrate.     

TiO2 nanotubes and CNT–TiO2 hybrid materials for the photocatalytic oxidation of propene at low concentration

In this work, we investigated titanium dioxide (TiO₂) nanotubes and CNT–TiO₂ hybrid materials for the photocatalytic oxidation (PCO) of propene at low concentration (100 ppmv) in gaseous phase. The materials were prepared via sol–gel method using sacrificial multi-walled carbon nanotubes (CNT) as templates and subsequent heat treatments to obtain the desired crystalline phase (anatase, rutile or a mixture of both) and eventually to remove the carbon template. We also studied rutile nanotubes for the first time and demonstrate that the activity strongly depends on the crystalline composition, following rutile < anatase < anatase/rutile mixture. The enhanced activity of the anatase–rutile mixture is attributed to the decrease in the electron–hole pair recombination due to the multiphasic nature of the particles. The key result of this work is the exceptional performance of the CNT–TiO₂ hybrid, which yielded the highest observed photocatalytic activity. The improved performance is attributed to synergistic effects due to the hybrid nature of the material, resulting in small anatase crystalline sizes (CNT act as heat sinks) and a reduced electron–hole pair recombination rate (CNTs act as electron traps). These results demonstrate the great potential of hybrid materials and stimulate further research on CNT-inorganic hybrid materials in photocatalysis and related areas.     

Multi-step purification of carbon nanotubes

An efficient purification procedure for multi-walled carbon nanotubes (MWNTs) synthesized by the floating catalyst method was discussed. The process involves ultra-sonication, heat treatment in hot water, bromination, oxidation and acid treatment. Most of amorphous carbon, multishell carbon nanocapsules as well as metal particles were successfully removed from the MWNT product. With this procedure, MWNTs with purity of more than 94% were obtained and the yield could approach 50%. It was found that bromination took an important role in the purification of MWNTs. Transmission electron microscopy, XPS and thermo-gravimetric analysis were used to evaluate the purification process of MWNTs. The mechanism of bromination on purification of the MWNTs was also discussed.     

Catalyst effect of metal cations on pyrolysis of hydrocarbon molecules and formation of carbon nanotubes in the channels of AlPO4-5 crystals

Ultra-small single-walled carbon nanotubes (SWNTs) with diameter of 0.4 nm were fabricated in the channels of AlPO₄-5 crystals by pyrolyzing hydrocarbon molecules. In order to improve the structural quality of the SWNTs, we introduced Br?nsted acid sites onto the channel walls by incorporating metal cations (Mn, Mg, Co, and Si) into AlPO₄-5 framework. The Br?nsted acid sites play an important catalytic role in the carbonization of hydrocarbon molecules (tripropylamine) in the AlPO₄-5 channels, and favor the formation of SWNTs, as revealed by the significant decrease in formation energy of the nanotubes. The experimental results agree well with the predictions of first-principles calculations.     

Thionine-mediated chemistry of carbon nanotubes

Thionine can be employed as a kind of useful functional molecule for the non-covalent functionalization of carbon nanotubes, as it shows a strong interaction with either SWNTs or MWNTs. Attachment of thionine molecules onto the sidewalls of carbon nanotubes would improve the solubility and lower the thermal stability of original carbon nanotubes. More importantly, it may functionalize the surface of carbon nanotubes with rich NH₂ groups and therefore open up more opportunities for the surface chemistry of carbon nanotubes. It has been proved that through the modification of small thionine molecules, other kinds of species such as cytochrome C and TiO₂ nanoparticles could be easily and selectively introduced onto the surface of carbon nanotubes. With this approach, SWNTs or MWNTs can be tailored with desired functional structures and properties.     

Effects of bimetallic catalyst composition and growth parameters on the growth density and diameter of carbon nanotubes

Multi-wall carbon nanotubes (MWNTs) were synthesized by catalytic decomposition of acetylene over Fe, Ni and Fe-Ni bimetallic catalysts supported on alumina under various controlled conditions. The growth density and diameter of CNTs were markedly dependent on the activation time of catalysts in H₂ atmosphere, reaction time, reaction temperature, flow rate of acetylene, and catalyst composition. Bimetallic catalysts were apt to produce narrower diameter of CNTs than single metal catalysts. For the growth of CNTs at 600 ‡C under 10/100 seem flow of C₂H₂/H₂ mixture, the narrowest diameter about 20 nm was observed at the reaction time of 1 h for 20Fe : 20Ni : 60Al₂O₃ catalyst, but at that of 1.5 h for 10Fe : 30Ni : 60Al₂O₃ catalyst. It was considered that the diameter and density of CNTs decreased with the increase of the growth time mainly due to hydrogen etching. The growth of CNTs followed the tip growth mode.     

Transparent conductive film based on carbon nanotubes and PEDOT composites

Single-walled nanotubes (SWNTs), thin multiwalled carbon nanotubes (t-MWNTs) and multiwalled carbon nanotubes (MWNTs) were treated with H₂SO₄–HNO₃ acid solution, under different chemical conditions. The acid-treated CNTs were dispersed in DI water and in poly (3,4-ethylenedioxythiophene) (PEDOT) solution. Furthermore, the finely dispersed CNTs/PEDOT solutions were employed to a simple method of bar coating to obtain the transparent conductive films on the glass and polyethylene terephthalate (PET) film. A sheet resistance of 247 Ω/sq and a transmission of 84.7% were obtained at a concentration of the acid-treated CNTs of 0.01 wt.%.     

Buckypaper-based catalytic electrodes for improving platinum utilization and PEMFC's performance

Platinum (Pt) catalytic electrode was developed by using carbon nanotube films (buckypaper) as supporting medium and electrodeposition method to deposit Pt catalyst. Buckypapers are free-standing thin films consisting of single-walled carbon nanotubes (SWNTs), multi-walled carbon nanotubes (MWNTs) and/or carbon nanofibers (CNFs) held together by van der Waals forces without any chemical binders. Special mixed buckypapers was developed by layered microstructures with a dense and high-conducting SWNT networks at the surface, as well as large porous structures of CNF networks as back supports. This unique microstructure can lead to improve Pt catalyst accessibility and mass exchange properties. Pt particles of about 6 nm were uniformly deposited in porous buckypapers. A promising electrochemical surface area of ∼40 m²/g was obtained from these electrodes. A Pt utilization as low as 0.28 g_Pt/kW was achieved for the cathode electrode at 80 °C. Pt utilization efficiency can be further improved by optimization of the electrodeposition condition in order to reduce the Pt particle size.     

99.9% purity multi-walled carbon nanotubes by vacuum high-temperature annealing

Ultrahigh purity multi-walled carbon nanotubes (MWNTs) were obtained, which were produced by a catalytic chemical vapor deposition method and subsequently annealed at vacuum pressures between 10⁻³ and 10 Pa and temperatures between 1500 and 2150 °C. Acid treatments were made for comparison. Scanning electron microscopy, transmission electron microscopy and energy dispersive spectra were used to characterize the specimens. Purities were characterized by thermogravimetric analysis. Raman spectra were also reported. The high-temperature vacuum process efficiently removed residual metal catalysts and metal oxide carriers and enhanced the graphitization of the MWNTs. The highest MWNT purity achieved is about 99.9%. This procedure presents a nondestructive, commercially viable purification method for carbon nanotubes.     

H2S oxidation by multi-wall carbon nanotubes decorated with tungsten sulfide

Tungsten sulfide catalysts decorated on single and multiwall carbon nanotubes (SWNTs & MWNTs) and activated carbon were synthesized, and XRD, ICP, SEM, TEM and ASAP analyses were employed to acquire the characteristics of each catalyst. Afterwards a gas flow containing 5,000 ppm of H₂S was passed over the catalyst in gas hour space velocity (GHSV) of 5,000 h^?1, temperature of 65 °C, steam volume percent of 20 and O₂/H₂S ratio equal to 2. The results revealed that the catalyst supported on MWNTs exhibited higher conversion amongst its counterparts. Then effects of GHSV, steam volume percent in the feed, catalyst loading and temperature were investigated on conversion of hydrogen sulfide to elemental sulfur for tungsten sulfide catalyst decorated on MWNTs.     

Lithium-ion battery anode properties of TiO2 nanotubes prepared by the hydrothermal synthesis of mixed (anatase and rutile) particles

From mixed (anatase and rutile) bulk particles, anatase TiO₂ nanotubes are synthesized in this study by an alkaline hydrothermal reaction and a consequent annealing at 300-400 °C. The physical and electrochemical properties of the TiO₂ nanotube are investigated for use as an anode active material for lithium-ion batteries. Upon the first discharge-charge sweep and simultaneous impedance measurements at local potentials, this study shows that interfacial resistance decreases significantly when passing lithium ions through a solid electrolyte interface layer at the lithium insertion/deinsertion plateaus of 1.75/2.0 V, corresponding to the redox potentials of anatase TiO₂ nanotubes. For an anatase TiO₂ nanotube containing minor TiO₂(B) phase obtained after annealing at 300 °C, the high-rate capability can be strongly enhanced by an isotropic dispersion of TiO₂ nanotubes to yield a discharge capacity higher than 150 mAh g⁻¹, even upon 100 cycles of 10 C-rate discharge-charge operations. This is suitable for use as a high-power anode material for lithium-ion batteries.     

An optimum NiO content in the CO2 reforming of CH4 with NiO/MgO solid solution catalysts

Reduced NiO/MgO, with a NiO content in the range 9.2–28.6 wt%, was found to be a highly effective catalyst for the CO₂ reforming of CH₄ to CO and H₂ (at 790°C, atmospheric pressure and a space velocity of 60000 cm³g^–1h^–1). For smaller or higher NiO contents, the yield was smaller, being negligible for 4.9 wt%. In contrast to the other reforming catalysts, the new catalyst has high stability, since in the optimum NiO range the CO yield remained unchanged at 95% for 120 h without any carbon deposition. The formation of a solid solution between NiO and MgO, which was demonstrated by both X-ray diffraction and temperature-programmed reduction, is most likely responsible for the high selectivity and stability in a large range of compositions of NiO/MgO.     

Catalytic Production of Carbon Nanotubes by Decomposition of CH4 over the Pre-reduced Catalysts LaNiO3, La4Ni3O10, La3Ni2O7 and La2NiO4

A large amount of more graphitic carbon nanotubes with a narrow size distribution was produced from catalytic decomposition of CH₄ over pre-reduced LaNiO₃, La₄Ni₃O₁₀, La₃Ni₂O₇ and La₂NiO₄. The structure and component of fresh and reduced LaNiO₃, La₄Ni₃O₁₀, La₃Ni₂O₇ and La₂NiO₄ were determined by X-ray diffraction (XRD). The carbon nanotubes obtained were characterized by means of transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Thermal oxidation of carbon nanotubes in air was made by thermogravimetric experiments (TG). The results revealed that the value of La/Ni in different catalyst precursors influences the diameter distribution and graphitic degree of carbon nanotubes. Lower La/Ni leads to wider diameter and higher graphitic degree of carbon nanotubes.     

Synthesis and characterization of double-walled carbon nanotubes from multi-walled carbon nanotubes by hydrogen-arc discharge

Double-walled carbon nanotubes (DWNTs) were synthesized in a large scale by a hydrogen arc discharge method using graphite powders or multi-walled carbon nanotubes/carbon nanofibers (MWNTs/CNFs) as carbon feedstock. The yield of DWNTs reached about 4 g/h. We found that the DWNT product synthesized from MWNTs/CNFs has higher purity than that from graphite powders. The results from high-resolution transmission electron microscopy observations revealed that more than 80% of the carbon nanotubes were DWNTs and the rest were single-walled carbon nanotubes (SWNTs), and their outer and inner diameters ranged from 1.75 to 4.87 nm and 1.06 to 3.93 nm, respectively. It was observed that the ends of the isolated DWNTs were uncapped and it was also found that cobalt as the dominant composition of the catalyst played a vital role in the growth of DWNTs by this method. In addition, the pore structures of the DWNTs obtained were investigated by cryogenic nitrogen adsorption measurements.     

Electrochemical performance of CoSb3/MWNTs nanocomposite prepared by in situ solvothermal synthesis

In situ solvothermally synthesized composite (SSC) and mechanically blended composite (MBC) of nanosized CoSb₃ and multiwalled carbon nanotubes (MWNTs) were prepared and investigated as potential anode materials for Li-ion batteries. It was found that SSC exhibits an entanglement structure of nanosized CoSb₃ and MWNTs and shows significantly better cycling stability than MBC. The reversible capacity of SSC electrode reaches 312 mA h g⁻¹ at the first cycle and remains above 265 mA h g⁻¹ after 30 cycles.