Yttrium oxide/silicon dioxide: a new dielectric structure forVLSI/ULSI circuits

Electrical characteristics of Al/yttrium oxide (~260 Å)/silicon dioxide (~40 Å)/Si and Al/yttrium oxide (~260 Å)/Si structures are described. The Al/Y₂O₃/SiO₂/Si (MYOS) and Al/Y₂ O₃/Si (MYS) capacitors show very well-behaved I-V characteristics with leakage current density <10^-10 A/cm² at 5 V. High-frequency C- V and quasistatic C-V characteristics show very little hysteresis for bias ramp rate ranging from 10 to 100 mV/s. The average interface charge density (Q_f+Q _it) is ~6×10¹¹/cm² and interface state density D_it is ~10¹¹ cm^-2-eV^-1 near the middle of the bandgap of silicon. The accumulation capacitance of this dielectric does not show an appreciable frequency dependence for frequencies varying from 10 kHz to 10 MHz. These electrical characteristics and dielectric constant of ~17-20 for yttrium oxide on SiO₂/Si make it a variable dielectric for DRAM storage capacitors and for decoupling capacitors for on-chip and off-chip applications     

Fabrication and characterization of metal-oxide-semiconductorfield-effect transistors and gated diodes using Ta2O5 gate oxide

N-channel metal oxide semiconductor field effect transistors (MOSFETs) using Ta₂O₅, gate oxide were fabricated. The Ta₂O₅ films were deposited by plasma enhanced chemical vapor deposition. The I_DS-V_DS and I_DS-V_GS characteristics mere measured. The electron mobility was 333 cm²/V·s. The subthreshold swing was 73 mV/dec. The interface trapped charge density, the surface recombination velocity, and the minority carrier lifetime in the field-induced depletion region measured from gated diodes were 9.5×10¹² cm^-2 eV^-1, 780 cm/s and 3×10^-6 sec, respectively. A comparison with conventional MOSFETs using SiO₂ gate oxide was made     

Fundamental characteristics of a magnetoresistive sensor using Y1Ba2Cu3O7-x ceramicsuperconducting films

The fundamental characteristics of a magnetic sensor fabricated from a Y₁Ba₂Cu₃O_7-x ceramic superconducting film are investigated. The operation principle of the sensor is based on the magnetoresistive properties of the material. The Y₁Ba₂Cu₃O_7-x ceramic film was prepared by the spray pyrolysis method. An element of the magnetic sensor consists of the film patterned to a meander shape. the sensitivity is discussed in connection with the noise measurement of the element. A magnetic field resolution of 2×10^-6 G/(Hz) ^1/2 at 100 Hz was obtained in the 0.1-100 G range. The sensitivity is much higher than that of a conventional semiconductor magnetic sensor. With an AC modulation provided by a magnetic field, phase detection of the magnetic field can be performed using a lock-in amplifier. An improvement in the low-frequency (<1 Hz) magnetic field resolution of about one order of magnitude was obtained using this method     

Increasing the current density of dielectric-base transistors withan MgO emitter-base barrier

We measured the current-voltage characteristics of YBa₂Cu₃O_7-x/oxide/n-SrTiO₃ diodes using NdGaO₃, LaAlO₃, CeO₂, and MgO as the oxide. MgO films had the highest current density. We then fabricated dielectric-base transistors with a YBa₂Cu₃ O_7-x(YBCO) emitter/collector on a SrTiO₃ dielectric base with an MgO barrier. The transistors had both voltage and current gains exceeding unity at 4.2 K. The emitter current density was about 4×10³ A/cm² at a collector-emitter voltage of 10 V and base-emitter voltage 10 V; this is 2 to 3 orders of magnitude larger than that of transistors with NdGaO₃ emitter-base barrier. We obtained a transconductance of around 0.4 mS at a collector-emitter voltage of 10 V for a device with a 6-μm-diameter emitter     

Electrical characteristics of high quality La2O3 gate dielectric with equivalent oxide thickness of 5 Å

Electrical and reliability properties of ultrathin La₂O ₃ gate dielectric have been investigated. The measured capacitance of 33 Å La₂O₃ gate dielectric is 7.2 μF/cm² that gives an effective K value of 27 and an equivalent oxide thickness of 4.8 Å. Good dielectric integrity is evidenced from the low leakage current density of 0.06 A/cm² at -1 V, high effective breakdown field of 13.5 MV/cm, low interface-trap density of 3×10¹⁰ eV^-1/cm², and excellent reliability with more than 10 years lifetime even at 2 V bias. In addition to high K, these dielectric properties are very close to conventional thermal SiO₂      

Saturable absorbers based on impurity and defect centers incrystals

Saturation of near-infrared absorption and transmission dynamics are investigated in tetravalent-chromium-doped Gd₃Sc₂ Ga₃O₁₂, Gd₃Sc₂Al₃ O₁₂, and Mg₂SiO₄ crystals, as well as in reduced SrTiO₃ using 20 ps 1.08 μm laser pulses. An absorption cross section of (5±0.5)×10^-18 cm² in garnets and (2.3±0.3)×10^-18 cm² in forsterite is estimated for the ³A ₂-³T₂ transition of tetrahedral Cr⁴⁺. Q-switched and ultra-short pulses are realized in neodymium lasers using chromium-doped crystals as the saturable absorbers. Saturation of free-carrier absorption with ultra-short relaxation time is observed in SrTiO₃ at 10⁸-10 ¹⁰ W/cm² pump intensities, while at 10¹⁰-10¹¹ W/cm² three-photon interband transitions predominate. The free-carrier absorption cross section is estimated to be (2.7±0.3)×10^-18 cm²     

Emission cross sections and spectroscopy of Ho3+ laserchannels in KGd(WO4)2 single crystal

The spectroscopic properties of Ho³⁺ laser channels in KGd(WO₄)₂ crystals have been investigated using optical absorption, photoluminescence, and lifetime measurements. The radiative lifetimes of Ho³⁺ have been calculated through a Judd-Ofelt (JO) formalism using 300-K optical absorption results. The JO parameters obtained were Ω₂=15.35×10^-20 cm², Ω ₄=3.79×10^-20 cm², Ω₆ =1.69×10^-20 cm². The 7-300-K lifetimes obtained in diluted (8·10¹⁸ cm^-3) KGW:0.1% Ho samples are: τ(⁵F₃)≈0.9 μs, τ( ⁵S₂)=19-3.6 μs, and τ(⁵F₅ )≈1.1 μs. For Ho concentrations below 1.5×10²⁰ cm^-3, multiphonon emission is the main source of non radiative losses, and the temperature independent multiphonon probability in KGW is found to follow the energy gap law τ_ph ^-1(0)=βexp(-αΔE), where β=1.4×10^-7 s^-1, and α=1.4×10³ cm. Above this holmium concentration, energy transfer between Ho impurities also contributes to the losses. The spectral distributions of the Ho³⁺ emission cross section σ_EM for several laser channels are calculated in σ- and π-polarized configurations. The peak a σ_EM values achieved for transitions to the ⁵I₈ level are ≈2×10^-20 cm² in the σ-polarized configuration, and three main lasing peaks at 2.02, 2.05, and 2.07 μm are envisaged inside the ⁵I₇→⁵I₈ channel     

Fabrication and characterization of high-performance InP/InGaAsdouble-heterojunction bipolar transistors

This paper is on high-performance InP/InGaAs double-heterojunction bipolar transistors (DHBT's) utilizing compositionally step-graded InGaAsP layers between the InGaAs base and InP collector to suppress the current blocking effect. These DHBT's exhibit current gains of 200 and excellent breakdown behavior. Moreover, the DHBT's permit collector current density levels J_C up to 3×10⁵ A/cm ² at V_CE=1.5 V. A current gain cutoff frequency of 155 GHz and a maximum oscillation frequency of 90 GHz have been successfully obtained at J_C=1.6×10⁵ A/cm². We have also investigated electron transport properties in the InP collector using a set of DHBT's with different injection energies into the InP collector. By increasing the injection energies, electron velocity is found to decrease from 3.5×10⁷ cm/s to 1.6×10⁷ cm/s, due to increased population of upper valleys. This result clearly demonstrates the significant role of nonequilibrium Γ-valley transport in determining the high-speed performance of InP/InGaAs DHBT's     

Optical absorption and stimulated emission of neodymium in yttriumorthosilicate

A spectroscopic investigation of the biaxial crystal yttrium orthosilicate doped with Nd³⁺(Nd³⁺:Y₂SiO₅) has been performed. Spectrally and orientationally resolved emission cross sections necessary for the evaluation of laser performance on the Nd^{3+ 4}F_3/2-⁴I _9/2 and ⁴F_3/2-⁴I_11/2 transitions have been determined. The Judd-Ofelt theory has been applied to measured values of optical absorption line strengths to obtain the orientation averaged intensity parameters: Ω₂-3.34×10^-20 cm², Ω ₄=4.35×10^-20 cm², and Ω₆=5.60×10^-20 cm². These Judd-Ofelt intensity parameter values are significantly different from those previously reported by A.M. Tkachuk et al. Using these intensity parameters, the Nd^{3+ 4}F₂ metastable state lifetime is predicted to be 225 μs. Measured low Nd concentration ⁴F_3/2 lifetimes of 214 μs indicate a high radiative quantum efficiency. Because of the Stark level splitting of the Nd^{3+ 4}F_3/2 and ⁴I_9/2 manifolds, laser operation at twice one of the Cs atomic resonance filter acceptance wavelengths is possible     

Bi1.5Zn1.0 Nb1.5O7栅绝缘层的SiO2修饰对ZnO-TFTs性能的影响

具有高介电常数的栅绝缘层材料存在某种极化及耦合作用,使得ZnO-TFTs具有高的界面费米能级钉扎效应、大的电容耦合效应和低的载流子迁移率.为了解决这些问题,本文提出了一种使用SiO₂修饰的Bi_1.5Zn_1.0Nb_1.5O₇作为栅绝缘层的ZnO-TFTs结构,分析了SiO₂修饰对栅绝缘层和ZnO-TFTs性能的影响.结果表明,使用SiO₂修饰后,栅绝缘层和ZnO-TFTs的性能得到显著提高,使得ZnO-TFTs在下一代显示领域中具有非常广泛的应用前景.栅绝缘层的漏电流密度从4.5×10^-5A/cm²降低到7.7×10^-7A/cm²,粗糙度从4.52nm降低到3.74nm,ZnO-TFTs的亚阈值摆幅从10V/dec降低到2.81V/dec,界面态密度从8×10¹³cm^-2降低到9×10¹²cm^-2,迁移率从0.001cm²/（V·s）升高到0.159cm²/（V·s）.     

Carrier transport related analysis of high-power AlGaN/GaN HEMTstructures

Shubnikov-de Haas (SdH) oscillation and Hall measurement results were compared with HEMT DC and RF characteristics for two different MOCVD grown AlGaN-GaN HEMT structures on semiinsulating 4H-SiC substrates. A HEMT with a 40-nm, highly doped AlGaN cap layer exhibited an electron mobility of 1500 cm²/V/s and a sheet concentration of 9×10¹² cm at 300 K (7900 cm²/V/s and 8×10¹² cm^-2 at 80 K), but showed a high threshold voltage and high DC output conductance. A 27-nm AlGaN cap with a thinner, lightly doped donor layer yielded similar Hall values, but lower threshold voltage and output conductance and demonstrated a high CW power density of 6.9 W/mm at 10 GHz. The 2DEG of this improved structure had a sheet concentration of n_SdH=7.8×10¹² cm^-2 and a high quantum scattering lifetime of τ_q=1.5×10^-13 s at 4.2 K compared to n_SdH=8.24×10¹² cm^-2 and τ_q=1.72×10^-13 s for the thick AlGaN cap layer structure, Despite the excellent characteristics of the films, the SdH oscillations still indicate a slight parallel conduction and a weak localization of electrons. These results indicate that good channel quality and high sheet carrier density are not the only HEMT attributes required for good transistor performance     

High-performance polycrystalline SiGe thin-film transistors usingAl2O3 gate insulators

The use of aluminum oxide as the gate insulator for low temperature (600°C) polycrystalline SiGe thin-film transistors (TFTs) has been studied. The aluminum oxide was sputtered from a pure aluminum target using a reactive N₂O plasma. The composition of the deposited aluminum oxide was found to be almost stoichiometric (i.e., Al₂O₃), with a very small fraction of nitrogen incorporation. Even without any hydrogen passivation, good TFT performance was measured an devices with 50-nm-thick Al₂O₃ gate dielectric layers. Typically, a field effect mobility of 47 cm²/Vs, a threshold voltage of 3 V, a subthreshold slope of 0.44 V/decade, and an on/off ratio above 3×10⁵ at a drain voltage of 0.1 V can be obtained. These results indicate that the direct interface between the Al₂ O₃ and the SiGe channel layer is sufficiently passivated to make Al₂O₃ a better alternative to grown or deposited SiO₂ for SiGe field effect devices     

Low-resistance bandgap-engineeredW/Si1-xGex/Si contacts

Bandgap-engineered W/Si_1-xGe_x/Si junctions (p⁺ and n⁺) with ultra-low contact resistivity and low leakage have been fabricated and characterized. The junctions are formed via outdiffusion from a selectively deposited Si_0.7Ge _0.3 layer which is implanted and annealed using RTA. The Si _1-xGe_x layer can then be selectively thinned using NH₄OH/H₂O₂/H₂O at 75°C with little change in characteristics or left as-deposited. Leakage currents were better than 1.6×10^-9 A/cm² (areal), 7.45×10^-12 A/cm (peripheral) for p⁺/n and 3.5×10^-10 A/cm² (peripheral) for n⁺/p. W contacts were formed using selective LPCVD on Si_1-xGe_x. A specific contact resistivity of better than 3.2×10^-8 Ω cm² for p ⁺/n and 2.2×10^-8 Ω cm² for n⁺/p is demonstrated-an order of magnitude n⁺ better than current TiSi₂ technology. W/Si_1-xGe _x/Si junctions show great potential for ULSI applications     

Fabrication of planar optical waveguides in LiB3O5 by 2 MeV He+ ion implantation

The fabrication of planar optical waveguides in LiB₃O ₅ is discussed. Using 2-MeV ⁴He⁺ implantation with a dose of 1.5×10¹⁶ ions/cm² at 300 K, the refractive indexes of a 0.2-μm-thick layer 5.1 μm below the crystal surface are reduced to form optical barrier guides. For this ion dose the maximum change from the bulk values of refractive index at a wavelength of 0.488 μm are 1.5%, 5.25%, and 4% for n_x, n_y, and n_z, respectively. The refractive indexes of the guiding region change by less than 0.02% from the bulk values. The dose dependence of the optical barrier height has been measured. A threshold ion dose of about 0.75×10¹⁶ ions/cm² is required to form a refractive index barrier and ion doses higher than about 2.5×10¹⁶ ions/cm². saturate the refractive index decrease. Waveguide propagation losses for annealed single energy implants of dose 1.5×10¹⁶ ions/cm² are dominated by tunneling and are estimated to be ~8.9 dB/cm for the z-cut waveguides used. Multiple energy implants broaden the optical barrier, and losses of <4 dB/cm have been observed     

Electrical conduction and dielectric breakdown in aluminum oxideinsulators on silicon

Leakage currents and dielectric breakdown were studied in MIS capacitors of metal-aluminum oxide-silicon. The aluminum oxide was produced by thermally oxidizing AlN at 800-1160°C under dry O₂ conditions. The AlN films were deposited by RF magnetron sputtering on p-type Si (100) substrates. Thermal oxidation produced Al ₂O₃ with a thickness and structure that depended on the process time and temperature. The MIS capacitors exhibited the charge regimes of accumulation, depletion, and inversion on the Si semiconductor surface. The best electrical properties were obtained when all of the AlN was fully oxidized to Al₂O₃ with no residual AlN. The MIS flatband voltage was near 0 V, the net oxide trapped charge density, Q_0x, was less than 10¹¹ cm ^-2, and the interface trap density, D_it, was less than 10¹¹ cm^-2 eV^-1, At an oxide electric field of 0.3 MV/cm, the leakage current density was less than 10^-7 A cm^-2, with a resistivity greater than 10 ¹² Ω-cm. The critical field for dielectric breakdown ranged from 4 to 5 MV/cm. The temperature dependence of the current versus electric field indicated that the conduction mechanism was Frenkel-Poole emission, which has the property that higher temperatures reduce the current. This may be important for the reliability of circuits operating under extreme conditions. The dielectric constant ranged from 3 to 9. The excellent electronic quality of aluminum oxide may be attractive for field effect transistor applications     

Investigation of inductively coupled plasma gate oxide on lowtemperature polycrystalline-silicon TFTs

By optimizing the inductively coupled plasma (ICP) oxidation condition, a thin oxide of 10 nm has been grown at 350°C to achieve excellent gate oxide integrity of low leakage current<5×10^-8 A/cm² (at 8 MV/cm), high breakdown field of 9.3 MV/cm and low interface trap density of 1.5×10¹¹ /eV cm². The superior performance poly-Si TFTs using such a thin ICP oxide were attained to achieve a high ON current of 110 μA/μm at V_D=1 V and V_G=5 V and the high electron field effect mobility of 231 cm²/V·S     

Steady-state and transient forward current-voltage characteristicsof 4H-silicon carbide 5.5 kV diodes at high and superhigh currentdensities

Steady-state and transient forward current-voltage I-V characteristics have been measured in 5.5 kV p⁺-n-n⁺ 4H-SiC rectifier diodes up to a current density j≈5.5×10 ⁴ A/cm². The steady-state data are compared with calculations in the framework of a model, in which the emitter injection coefficient decreases with increasing current density. To compare correctly the experimental and theoretical results, the lifetime of minority carriers for high injection level, τ_ph, has been estimated from transient characteristics. At low injection level, the hole diffusion length L_pl has been measured by photoresponse technique. For a low-doped n-base, the hole diffusion lengths are L_pl≈2 μm and L_ph≈6-10 μm at low and high injection levels respectively. Hole lifetimes for low and high injection levels are τ_pl≈15 ns and τ_ph≈140-400 ns. The calculated and experimental results agree well within the wide range of current densities 10 A/cm ²3 A/cm². At j>5 kA/cm², the experimental values of residual voltage drop V is lower than the calculated ones. In the range of current densities 5×10³ A/cm²4 A/cm², the minimal value of differential resistance R_d =dV/dj is 1.5×10^-4 Ω cm². At j>25 kA/cm², R_d increases with increasing current density manifesting the contribution of other nonlinear mechanisms to the formation steady-state current-voltage characteristic. The possible role of Auger recombination is also discussed     

Experimental determination of electron drift velocity in 4H-SiC p+-n-n+ avalanche diodes

4H-SiC p⁺-n-n⁺ diodes of low series resistivity (<1×10^-4 Ω·cm²) were fabricated and packaged. The diodes exhibited homogeneous avalanche breakdown at voltages U_b=250-270 V according to the doping level of the n layer. The temperature coefficient of the breakdown voltage was measured to be 2.6×10^-4 k^-1 in the temperature range 300 to 573 K. These diodes were capable of dissipating a pulsed power density of 3.7 MW/cm² under avalanche current conditions. The transient thermal resistance of the diode was measured to be 0.6 K/W for a 100-ns pulse width, An experimental determination of the electron saturated drift velocity along the c-axis in 4H-SIC was performed for the first time, It was estimated to be 0.8×10⁷ cm/s at room temperature and 0.75×10⁷ cm/s at approximately 360 K     

Erase/write cycle tests of n-MOSFETs with Si-implantedgate-SiO2

To discuss the applicability of a MOSFET with Si-implanted gate-SiO₂ of 50 nm thickness to a non volatile random access memory (NVRAM) operating more than 3.3×10¹⁵ erase/write (E/W) cycles, E/W-cycle tests were performed up to 10¹¹ cycles by measuring the hysteresis curve observed in a source follower MOSFET in which a sine-wave voltage of 100 kHz was supplied to the gate. Degradations in the threshold-voltage window of 15 V and gain factor were scarcely observed in a MOSFET with Si-implantation at 50 keV/1×10¹⁶ cm^-2 at a gate voltage of ±40 V. Those degradations observed in a MOSFET with 25 keV/3×10¹⁶ cm^-2 were improved by lowering the gate voltage from ±40 V to ±30 V in sacrificing the smaller threshold-voltage window from 20 to 8.5 V     

P-type 4H and 6H-SiC high-voltage Schottky barrier diodes

High-voltage Schottky barrier diodes have been successfully fabricated for the first time on p-type 4H- and 6H-SiC using Ti as the barrier metal. Good rectification was confirmed at temperatures as high as 250°C. The barrier heights were estimated to be 1.8-2.0 eV for 6H-SiC and 1.1-1.5 eV for 4H-SiC at room temperature using both I-V and C-V measurements. The specific on resistance (R_on,sp) for 4H- and 6H-SiC were found to be 25 mΩ cm^-2 and 70 mΩ cm^-2 at room temperature. A monotonic decrease in resistance occurs with increasing temperature for both polytypes due to increased ionization of dopants. An analytical model is presented to explain the decrease of R_on,sp with temperature for both 4H and 6H-SiC which fits the experimental data. Critical electric field strength for breakdown was extracted for the first time in both p-type 4H and 6H-SiC using the breakdown voltage and was found to be 2.9×10⁶ V/cm and 3.3×10⁶ V/cm, respectively. The breakdown voltage remained fairly constant with temperature for 4H-SiC while it was found to decrease with temperature for 6H-SiC