聚合物基复合材料吸湿研究进展

聚合物基复合材料的吸湿性能是其研究重点之一,重点综述了聚合物基复合材料的相关吸湿机理,对不同情况下的吸湿过程和吸湿曲线进行了详细分析。阐述了外界条件和材料本身参数对材料吸湿的影响,以及吸湿后聚合物基复合材料各项性能的变化,并分析了造成这些变化的原因。最后对最新的天然植物纤维增强复合材料的吸湿进行了简单介绍。     

吸湿发热材料的研究进展

综述了吸湿性和发热材料的主要类型、研究状况,探讨了吸湿发热材料的吸湿发热机理,展望了吸湿发热材料的发展和应用前景.     

浸泡腐蚀对玻璃纤维-空心玻璃微珠/环氧树脂复合泡沫材料弯曲性能的影响

制备了不同纤维质量分数的玻璃纤维-空心玻璃微珠/环氧树脂复合泡沫材料。通过三点弯曲试验研究了纤维质量分数对复合泡沫材料力学性能的影响。将复合泡沫材料试件置于蒸馏水和海水中浸泡,研究了浸泡腐蚀对试件弯曲性能的影响,并结合扫描电镜照片分析其原因。研究表明:纤维质量分数越高,玻璃纤维-空心玻璃微珠/环氧树脂复合泡沫材料的吸湿率越大,且在蒸馏水中的吸湿率较海水中的更大。试件的弯曲强度随纤维质量分数增加而增大,当纤维质量分数为10%时达到最大,比未添加纤维的试件增强了51%,之后则随纤维质量分数增加逐渐降低。浸泡腐蚀降低了试件的弯曲性能,其中海水浸泡后的试件弯曲性能最低。玻璃纤维-空心玻璃微珠/环氧树脂复合泡沫材料弯曲强度降低的直接原因是浸泡腐蚀使得部分玻璃微珠和玻璃纤维与环氧树脂基体间的界面层受到破坏。     

湿热环境对PMI泡沫夹芯复合材料性能的影响

采用聚甲基丙烯酰亚胺（PMI）泡沫、碳纤维增强环氧树脂（EW220/5258）复合材料面板制备了PMI泡沫夹芯复合材料,研究了PMI泡沫夹芯复合材料、EW220/5258复合材料面板及PMI泡沫芯材的吸湿特性,并讨论了湿热对PMI泡沫夹芯复合材料的压缩性能及介电性能的影响。结果发现：PMI泡沫夹芯复合材料的饱和吸湿时间...     

浸泡腐蚀对泡沫铝-环氧树脂复合材料弯曲性能的影响

制备了两种泡沫铝孔径的泡沫铝-环氧树脂复合材料。将试件分别浸泡于蒸馏水和海水中,得出了其吸湿率与浸泡时间的关系曲线。通过三点弯曲实验研究了浸泡腐蚀对复合材料弯曲强度和弯曲刚度等力学性能的影响。研究结果表明:泡沫铝-环氧树脂复合材料的吸湿率随浸泡时间的延长而逐渐增大,且试件在海水中浸泡的吸湿率大于在蒸馏水中的吸湿率。浸泡腐蚀大幅度地降低了泡沫铝-环氧树脂复合材料的弯曲力学性能。添加偶联剂的试件的弯曲强度和弯曲刚度均比无偶联剂试件的值更大,特别是对于泡沫铝孔径为2mm的复合材料试件,添加偶联剂使得其弯曲强度和弯曲刚度分别提高了51.7%和65.4%。另外,1mm孔径泡沫铝复合材料试件的弯曲强度和弯曲刚度均比2mm孔径泡沫铝复合材料试件的值更大。     

工业闭孔泡沫铝压缩力学性能及变形机理

泡沫铝是一种新型的结构和功能材料,因特殊的能量吸收特性而在工程领域具有很好的应用前景。为了研究基体材料对泡沫铝力学性能和变形失效机理的影响,同时为工业泡沫铝材料提供更具参考价值的性能指标,对工业上最常见的两种不同基体(纯铝基体和7050铝合金基体)的泡沫铝材料进行了准静态压缩力学性能的试验,并对其变形机理进行了分析。试验结果表明,相同规格的7050基体泡沫铝的压缩力学性能高于纯铝基体泡沫铝,能量吸收能力也远大于纯铝基体泡沫铝。纯铝基体泡沫铝在压缩载荷下呈现逐层坍塌、连续性破坏的模式,试件在完全压实后呈碎渣;7050基体泡沫铝表现出逐层坍塌、间断式破坏的模式,试件在完全压实后呈完整的块状。7050基体泡沫铝的泡孔结构比纯铝基体泡沫铝均匀,力学性能更加稳定。     

有机高分子吸湿材料的吸附模型与机理

选聚丙烯酸钠(PAA)、聚丙烯酰胺(PAM)、丙烯酸-甲基丙烯酸共聚物P(AA-MA)、丙烯酸-丙烯酰胺共聚物P(AA-AM)、丙烯酸-甲基丙烯酸-丙烯酰胺共聚物P(AA-AM-MA),系统研究其吸湿过程和机理。吸湿性能的测试结果表明,硅胶和分子筛10 h内便饱和,有机高分子吸湿材料仍能持久吸湿,其饱和吸湿容量比硅胶提高至少6%以上,比分子筛提高至少50%以上,吸湿速率快于硅胶和分子筛。吸附动力学实验表明,有机高分子吸湿材料的吸湿主要遵循准二级动力学模型,吸湿率受湿度和高分子树脂自身的吸附性能影响。Freundlich吸附等温模型证实有机高分子吸湿材料吸湿并非单层吸附,而是物理吸附和化学吸附同时发生,且多以化学吸附为主。热力学分析得该吸湿过程为吸热反应且可自发进行。     

环氧树脂复合泡沫材料的压缩力学性能

对空心玻璃微珠填充环氧树脂复合泡沫材料进行了准静态压缩实验, 研究了材料的宏观压缩力学性能, 并提出了弹性模量和屈服强度的预测公式。此外, 对压缩试件的断口进行了宏、细观观察, 研究了材料的压缩破坏机理。结果表明, 复合泡沫材料在压缩过程中, 具有普通泡沫材料的应力-应变曲线的典型特征, 在应变为2 %左右时材料发生屈服, 在应变大于30 %后发生破坏。此外, 材料的杨氏模量和强度均随密度的减小而下降, 预测公式给出的结果与实验值基本一致。压缩试件断口的宏、细观观察表明, 复合泡沫材料主要的破坏形式为剪切引起的弹塑性破坏。      

导电聚烯烃泡沫研制

着重对泡沫材料“导电补偿机理”进行了描述。此外，就交联对电性能及泡沫发泡性的影响进行了探讨。     

泡沫铝吸声性能的研究进展

泡沫铝的孔结构和金属特性使其具有优异的吸声性能。介绍了泡沫铝吸声性能的研究进展,并分析了当前研究中存在的问题,对未来泡沫铝在吸声领域的研究做出展望。未来需进一步研究泡沫铝材料的吸声机理,尝试将结构参数对吸声系数值的影响定量化,系统研究组合结构的吸声性能;探索建立闭孔泡沫铝材料吸声的理论模型,实现对吸声的理论预测、分析与计算,为实际应用提供指导。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from