Dynamic Response of Three Fiber Reinforced Polymer Composite Bridges

Fiber reinforced polymer (FRP) composite bridge decks are gaining the attention of bridge owners because of their light self-weight, corrosion resistance, and ease of installation. Constructed Facilities Center at West Virginia University working with the Federal Highway Administration and West Virginia Department of Transportation has developed three different FRP decking systems and installed several FRP deck bridges in West Virginia. These FRP bridge decks are lighter in weight than comparable concrete systems and therefore their dynamic performance is equally as important as their static performance. In the current study dynamic tests were performed on three FRP deck bridges, namely, Katy Truss Bridge, Market Street Bridge, and Laurel Lick Bridge, in the state of West Virginia. The dynamic response parameters evaluated for the three bridges include dynamic load allowance (DLA) factors, natural frequencies, damping ratios, and deck accelerations caused by moving test trucks. It was found that the DLA factors for Katy Truss and Market Street bridges are within the AASHTO 1998 LRFD specifications, but the deck accelerations were found to be high for both these bridges. DLA factors for Laurel Lick bridge were found to be as high as 93% against the typical design value of 33%; however absolute deck stress induced by vehicle loads is less than 10% of the deck ultimate stress.     

Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Response of Prestressed Concrete I-Girder Bridges to Live Load

Design and evaluation of prestressed concrete I-girder bridges is in large part dependent on the transverse load distribution characteristics and the dynamic load amplification, as well as service level, live load, and tensile stresses induced in the girders. This study presents the results of field tests conducted on three prestressed concrete I-girder bridges to obtain dynamic load allowance statistics, girder distribution factors (GDF), and service level stress statistics. The field-based data are also compared to approximate and numerical model results. Bridge response was measured at each girder for the passage of test trucks and normal truck traffic. The dynamic amplification is observed to be a strong function of peak static stress and a weak function of vehicle speed and is independent of span length, number of axles, and configuration. GDFs for one- and two-lanes are less than code specified GDFs. Results from the numerical grillage models agree closely with experimentally derived results for transverse distribution.     

Impact Factors for Horizontally Curved Composite Box Girder Bridges

This paper presents a method for determining the dynamic impact factors for horizontally curved composite single- or multicell box girder bridges under AASHTO truck loading. The bridges are modeled as three-dimensional structures using commercially available software. The vehicle is idealized as a pair of concentrated forces, with no mass, traveling in two circumferential paths parallel to the curved centerline of bridges. An extensive parametric study is conducted, in which over 215 curved composite box girder bridge prototypes are analyzed. The key parameters considered in this study are: Number of cells, number of lanes, degree of curvature, arc span length, slope of the outer steel webs, number and area of bracing and top chord systems, and truck(s) speed and truck(s) positioning. Based on the data generated from the parametric study, expressions for dynamic impact factors for longitudinal moment, reaction, and deflection are proposed as function of the ratio of the arc span length to the radius of curvature. The results from this study would enable bridge engineers to design horizontally curved composite box girder bridges more reliably and economically. Furthermore, the results can be used to potentially increase the live-load capacity of existing bridges to prevent posting or closing of the bridge.     

Measurement of Truck Axle Weights by Instrumenting Longitudinal Ribs of Orthotropic Bridge

The longitudinal ribs of an orthotropic box-girder bridge were instrumented to measure axle weights of trucks. The bending stress in the longitudinal rib is composed of a girder component, i.e., the flexural stress due to the rib’s function as part of the box-girder’s upper flange in carrying vehicles, and a rib component, i.e., the part of stress produced in the rib when it is viewed as a continuous beam supporting wheel loads. The instrumentation locations were set close to the middle support of the two-span continuous bridge to reduce girder component and impact effect. All possible wheel-supporting ribs inside the box girder were instrumented to cover most transverse locations of truck wheels. Deviating passes as well as central passes were carried out for each traffic lane in calibration tests to catch maximum stress response. The results of the calibration tests were used to solve the influence lines of the girder component and rib component at each strain gauge. With these influence lines, the rib component was separated from girder one in the stress waves of the 3-day live traffic measurements, and axle weights of the truck traffic were subsequently calculated.     

Dynamic and Static Behavior of a Curved-Girder Bridge with Varying Boundary Conditions

A curved, three-span continuous, steel I-girder bridge in Salt Lake City was tested in order to determine its dynamic and static load carrying properties for three boundary condition states. For each of the three boundary condition states, two dynamic forced vibration methods were applied to the bridge as well as a static live-load test. The first forced vibration method used an eccentric mass shaker. The second method involved striking the side of the bridge with an impact hammer. The live-load test was performed by slowly driving a truck at a crawl speed across the bridge. Velocity transducers, accelerometers, and strain gauges were utilized to record the response of the bridge. The analysis and compilation of recorded dynamic response of the bridge enabled the preparation of mode shapes and natural frequencies for each boundary condition. This paper discusses the resulting changes in relevant dynamic properties and compares them with the changes in the static properties that were determined from the bridge response recorded from the live-load tests.     

Load Distribution and Impact Factors for I-Girder Bridges

This paper presents the procedure and results of field tests that were performed on two simply supported steel I-girder bridges to assess girder distribution and impact factors. The measurements were performed under normal truck traffic. Strain data were taken from bottom flanges of girders in the middle of a span. Additional strain data were obtained under passes of a control truck with known weight and configuration. A computerized data acquisition technique enabled selective recording of the significant blocks of the strain data under normal traffic. Strains were measured for two consecutive days on each bridge. Measured data consist of strain blocks from approximately 900 trucks. The strain records were filtered with a lowpass digital filter to remove the dynamic components and to obtain an equivalent static strain. The data were further processed to obtain statistical parameters (mean and standard deviation) of the girder distribution and impact factors. The results were compared with the values calculated according to American Association of State Highway and Transportation (AASHTO) methods. Measured girder distribution factors are lower than AASHTO values. Measured impact factors are well below AASHTO values.     

Field Performance of FRP Bridge Repairs

Many reinforced concrete bridges throughout the United States on county and state highway systems are deteriorated and∕or distressed to such a degree that structural strengthening of the bridge or reducing the allowable truck loading on the bridge by load posting is necessary to extend the service life of the bridge. The structural performance of many of these bridges can be improved through external bonding of fiber-reinforced plastic (FRP) laminates or plates. This paper describes the rehabilitation of an existing concrete bridge in Alabama through external bonding of FRP plates to the bridge girders. Field load tests were conducted before and after application of the FRP plates, and the response of the bridge to test vehicle loadings was recorded. Results of the field tests are reported, and the effects of the FRP plates on the bridge response are identified. The repaired bridge structure exhibited a decrease in steel reinforcing bar stresses and vertical midspan deflections. These decreases ranged from 4 to 12% for various static and dynamic loading cases.     

Vehicle Induced Dynamic Behavior of Short-Span Slab Bridges Considering Effect of Approach Slab Condition

In this paper the vehicle induced dynamic bridge responses are calculated by modeling the bridge and vehicle as one coupled system. The dynamic behavior of short slab bridges with different span lengths induced by the AASHTO HS20 truck is investigated. A parametric study is conducted to analyze the effects of different truck speeds and different road surface conditions. Critical truck speeds that result in peaks of dynamic response are found to follow the rule that describes the resonant vibration of bridges due to train loading. The approach slab condition that consists of faulting at the ends and deformation along the span is considered in the analysis. Although the effect of the along-span deformation on the dynamic response of bridges is trivial, the faulting condition of the approach slab is found to cause significantly large dynamic responses in short-span slab bridges. Impact factors obtained from numerical analyses are compared with those values specified in the AASHTO codes.     

Live Load Distribution for Steel Girder Bridges

This paper deals with distribution of truck load on girder bridges. Previous analytical studies based on finite-element method indicated that AASHTO code-specified girder distribution factors (GDFs) are inaccurate. In particular, GDFs appear to be conservative for longer spans and larger girder spacing, but too permissive for short spans and girder spacings. Therefore, a field testing program was carried out including about 20 steel girder bridges with spans up to 45 m. For each tested structure, GDFs were determined by measuring strains in the girders under heavy trucks. Test trucks were 11-axle vehicles, loaded to the legal limit in Michigan (over 650 kN). The strains were recorded for a single truck and for two trucks side-by-side. The tests were repeated for crawling speed and normal traffic speed for the location. In all tested bridges, the GDFs determined from the field measurements are lower than code-specified values. In addition, the considered bridges were analyzed using a commercial finite-element software package, ABAQUS. The analytical results were compared with those from field tests. It was observed that the maximum values of the strain and corresponding stress are lower than analytical values obtained using ABAQUS. The reason for this discrepancy is unintended composite action and partial fixity of supports (rather than simple supports).     

Implementation of a Long-Term Bridge Weigh-In-Motion System for a Steel Girder Bridge in the Interstate Highway System

This technical paper discusses the implementation of a long-term bridge weigh-in-motion system for use in determining gross vehicle weights of trucks crossing steel girder bridges. The system uses strain data to determine truck weights using an existing structural health monitoring system installed on a interstate highway bridge. The applied system has the advantage of not using any axle detectors in the roadway; and instead all analyses are performed using strain gauges attached directly to the steel girders, providing for a long-term monitoring system with minimal maintenance. Long-term data has been used to demonstrate that this method can be readily applied to gain important information on the quantity and weights of the trucks crossing the highway bridge.     

Impact Factors for Curved Continuous Composite Multiple-Box Girder Bridges

The results from a parametric study on the impact factors for 180 curved continuous composite multiple-box girder bridges are presented. Expressions for the impact factors for tangential flexural stresses, deflection, shear forces and reactions are deduced for AASHTO truck loading. The finite-element method was utilized to model the bridges as three-dimensional structures. The vehicle axle used in the analysis was simulated as a pair of concentrated forces moving along the concrete deck in a circumferential path with a constant speed. The effects of bridge configurations, loading positions, and vehicle speed on the impact factors were examined. Bridge configurations included span length, span-to-radius of curvature ratio, number of lanes, and number of boxes. The effect of the mass of the vehicle on the dynamic response of the bridges is also investigated. The data generated from the parametric study and the deduced expressions for the impact factors would enable bridge engineers to design curved continuous composite multiple-box girder bridges more reliably and economically.     

Experimental Evaluation of Dynamic Effects for a Selected Highway Bridge

The paper presents an experimental study of the actual dynamic effects for a preselected typical highway bridge. Knowledge of the dynamic impact factors is important for accurate determination of the ultimate load capacity and performance assessment of constructed bridges. Static and dynamic field tests were performed on a two-lane concrete highway bridge built in 1999 on U.S. 90 in northwest Florida. During the tests, one or two fully loaded trucks crossed over the bridge, which was instrumented with strain gauges, accelerometers, and displacement transducers. A wooden plank was placed across the lanes for some runs to trigger extensive dynamic vibration and to simulate poor road surface conditions. Data collected from the tests were used for comprehensive assessment of the bridge under dynamic loading. Impact factors obtained from the tests with higher speeds were found larger than corresponding values recommended by bridge codes. Analysis revealed that stiff vehicle suspension, road surface imperfection, and “bouncing” of the truck loading contributed to the high impact factors. Experimental data were also used for validation of the finite-element models developed for the vehicle–bridge system.     

Dynamic and Impact Behavior of Half-Through Arch Bridges

The objective of this paper is to present the results of an investigation of the dynamic and impact characteristics of half-through arch bridges with rough decks caused by vehicles moving across them. Seven arch bridges modeled as three-dimensional structures with overall span lengths ranging from 20?to?200?m (65.5?to?656.2?ft) are analyzed. The American Association of State Highway and Transportation Officials Specifications HS20-44 truck is the applied vehicle loading used in the analysis and is simulated as a three-dimensional, nonlinear vehicle model with 11 degrees of freedom. Truck components include the body, suspension, and tires. The bridge deck surface is assumed to have a “good” surface roughness and is simulated using a stochastic process (power spectral density function). The effect on impact factors of span length, rise-to-span ratio, and vehicle speed is discussed. The results of the analyses show that the impact factors of bending moment and axial force will not exceed 0.4 and 0.25, respectively. The proposed impact equations are simple and conservative and can be used in the design of half-through arch bridges.     

Predicting Truck Load Spectra under Weight Limit Changes and Its Application to Steel Bridge Fatigue Assessment

Truck weight-limit regulations have significant influence on truck operating weights. These regulations directly influence loads applied to highway facilities, such as bridges and pavements. “Truck weight” herein collectively refers to a vehicle’s gross weight, axle weights, and axle configuration. Truck load spectra as a result of truck weight limits are important to bridge engineering in many respects, such as that of determining requirements for evaluation and design of bridges for both strength and fatigue. This paper’s objective is to present a new method for predicting truck weight spectra resulting from a change in truck weight limits. This method is needed to estimate impacts of the change on highway bridges such as accelerated fatigue accumulation. Historical and recent truck weight data are used to test and illustrate the proposed method, and the results show its good prediction capability. This method is also applied here to an example of estimating the impact on steel bridge fatigue due to a possible increase in the gross-vehicle-weight limit from 356 kN (80 kips) on five axles to 431 kN (97 kips) on six axles. Also included is an investigation of the AASHTO fatigue truck model for steel bridge evaluation. Results show that the current fatigue truck model may become invalid under the studied scenario of truck weight-limit increase.     

Behavior of Reinforced Concrete Bridge Decks on Skewed Steel Superstructure under Truck Wheel Loads

This paper focuses on the behavior of skewed concrete bridge decks on steel superstructure subjected to truck wheel loads. It was initiated to meet the need for investigating the role of truck loads in observed skewed deck cracking, which may interest bridge owners and engineers. Finite-element analysis was performed for typical skewed concrete decks, verified using in?situ deck strain measurement during load testing of a bridge skewed at 49.1°. The analysis results show that service truck loads induce low strains/stresses in the decks, unlikely to initiate concrete cracking alone. Nevertheless, repeated truck wheel load application may cause cracks to become wider, longer, and more visible. The local effect of wheel load significantly contributes to the total strain/stress response, and the global effect may be negligible or significant, depending on the location. The current design approach estimates the local effect but ignores the global effect. It therefore does not model the situation satisfactorily. In addition, total strain/stress effects due to truck load increase slightly because of skew angle.     

Static Load Tests of a Road Bridge with a Flexible Structure Made from Super Cor Type Steel Corrugated Plates

The way in which a new road bridge made from Super Cor steel plates was tested is described and the test results for three static load schemes in which one ballasting vehicle (a Scania truck) was used as the load are presented. The tested bridge has a box structure and it is located on the Gim?n River in Gim?n, Sweden on the Br?cke-Holm road. The bridge has an effective span of 12.315?m and a clear height of 3.555?m. The span’s steel shell is founded on two reinforced concrete continuous footings. The average measured displacements and strains (normal stresses) in selected points and elements of the steel shell structure were found to be much smaller than the ones calculated for the same load. The conclusions drawn from this research can be useful for assessing the performance of such steel shells and their interaction with the surrounding backfill. Since such steel–soil designs are used more and more often for small and medium-sized bridges on road and railway lines in Poland and in the world, the conclusions from the static load tests can be generalized to a whole class of similar bridge designs.     

Equivalent Wheel Load Approach for Slender Cable-Stayed Bridge Fatigue Assessment under Traffic and Wind: Feasibility Study

In the current AASHTO LRFD specifications, the fatigue design considers only one design truck per bridge with 15% dynamic allowance. While this empirical approach may be practical for regular short and medium span bridges, it may not be rational for long-span bridges (e.g., span length >152.4?m or 500?ft) that may carry many heavy trucks simultaneously. Some existent studies suggested that fatigue may not control the design for many small and medium bridges. However, little research on the fatigue performance of long-span bridges subjected to both wind and traffic has been reported and if fatigue could become a dominant issue for such a long-span bridge design is still not clear. Regardless if the current fatigue design specifications are sufficient or not, a real understanding of the traffic effects on bridge performance including fatigue is desirable since the one truck per bridge for fatigue design does not represent the actual traffic condition. As the first step toward the study of fatigue performance of long-span cable-stayed bridges under both busy traffic and wind, the equivalent dynamic wheel load approach is proposed in the current study to simplify the analysis procedure. Based on full interaction analyses of a single-vehicle–bridge–wind system, the dynamic wheel load of the vehicle acting on the bridge can be obtained for a given vehicle type, wind, and driving condition. As a result, the dimension of the coupled equations is independent of the number of vehicles, through which the analyses can be significantly simplified. Such simplification is the key step toward the future fatigue analysis of long-span bridges under a combined action of wind and actual traffic conditions.     

Analytical and Experimental Investigation of Bridge Girder Shear Distribution Factors

Tests on twelve bridges (six along Interstate 55 and six along Interstate 70/270 in Illinois) were performed to determine the validity of certain provisions for calculating bearing forces in the load and resistance factor design (LRFD) and the load factor design bridge specifications. The bridges were selected to be typical of Illinois interstate highway bridges and maintain a range of parameters to study. These bridges were instrumented on their beam webs with three strain gauge rosettes installed on each beam to measure shear stresses caused by loads. Static tests and slow moving 8 km/h (5?mi/h) tests with a loaded truck in specified locations were performed. Dynamic tests at highway speeds were also completed. Finite-element models were developed and compared to the test results. The study shows that the LRFD specification procedures closely approximate the shear distribution factors determined by finite-element analysis and testing.     

Nonlinear Analysis of Ordinary Bridges Crossing Fault-Rupture Zones

Rooted in structural dynamics theory, three approximate procedures for estimating seismic demands for bridges crossing fault-rupture zones and deforming into their inelastic range are presented: modal pushover analysis (MPA), linear dynamic analysis, and linear static analysis. These procedures estimate the total seismic demand by superposing peak values of quasi-static and dynamic parts. The peak quasi-static demand in all three procedures is computed by nonlinear static analysis of the bridge subjected to peak values of all support displacements applied simultaneously. In the MPA and the linear dynamic analysis procedures, the peak dynamic demand is estimated by nonlinear static (or pushover) analysis and linear static analysis, respectively, for forces corresponding to the most-dominant mode. In the linear static analysis procedure, the peak dynamic demand is estimated by linear static analysis of the bridge due to lateral forces appropriate for bridges crossing fault-rupture zones. The three approximate procedures are shown to provide estimates of seismic demands that are accurate enough to be useful for practical applications. The linear static analysis procedure, which is much simpler than the other two approximate procedures, is recommended for practical analysis of “ordinary” bridges because it eliminates the need for mode shapes and vibration periods of the bridge.