Response of Prestressed Concrete I-Girder Bridges to Live Load

Design and evaluation of prestressed concrete I-girder bridges is in large part dependent on the transverse load distribution characteristics and the dynamic load amplification, as well as service level, live load, and tensile stresses induced in the girders. This study presents the results of field tests conducted on three prestressed concrete I-girder bridges to obtain dynamic load allowance statistics, girder distribution factors (GDF), and service level stress statistics. The field-based data are also compared to approximate and numerical model results. Bridge response was measured at each girder for the passage of test trucks and normal truck traffic. The dynamic amplification is observed to be a strong function of peak static stress and a weak function of vehicle speed and is independent of span length, number of axles, and configuration. GDFs for one- and two-lanes are less than code specified GDFs. Results from the numerical grillage models agree closely with experimentally derived results for transverse distribution.     

Effects of Pier and Deck Flexibility on the Seismic Response of Isolated Bridges

The seismic response of bridges isolated by elastomeric bearings and the sliding system is investigated under two horizontal components of real earthquake ground motions. The selected bridges consist of multispan continuous deck supported on the piers and abutments. Three different mathematical models of the isolated bridge are considered for the analytical seismic response by considering and ignoring the flexibility of the deck and piers. The mathematical formulation for seismic response analysis of various mathematical models of the bridges isolated by different isolation systems is presented. The accuracy and computational efficiency of various mathematical models of isolated bridges is investigated by comparing their responses under different system parameters and earthquake ground motions. The important parameters selected are the flexibility of deck, piers, and isolation systems. There was significant difference in the computational time required for different models, but it was observed that the seismic response of the bridges obtained from different equivalent mathematical models is quite comparable even for an unsymmetrical bridge. Thus, the earthquake response of a seismically isolated bridge can be effectively obtained by modeling it as a single-degree-of-freedom system (i.e., considering the piers and deck as rigid) supported on an isolation system in two horizontal directions.     

Simulation of Construction of Cable-Stayed Bridges

Construction of cable-stayed bridges involves major changes in configuration of the structure with the addition and removal of structural components to the partially constructed structure. At every stage of construction, it is necessary to have sufficient information about the existing partial structure as-built, to verify the requirements called for in the construction guidelines and to investigate the effects of possible modifications in the construction procedures. The final stresses and deformations in the completed structure are strongly dependent on the sequence of events during the construction and the erection procedure used. Therefore, analysis of the actual construction sequence is an important first step in any analysis of the performance of the bridge under external loads. In this paper a general methodology for construction sequence simulation of cable-stayed bridges is presented, and stage-by-stage construction of an actual bridge is simulated. The objective of the simulation is to evaluate short-term and long-term influences of the construction sequence on the structural integrity of the cable-stayed bridge. Comparisons are presented between results from the present analysis, conventional procedures, and the actual field measurements.     

Stability Analysis of Box-Girder Cable-Stayed Bridges

The objective of this study is to investigate the stability characteristics of box-girder cable-stayed bridges by three-dimensional finite-element methods. Cable-stayed bridges have many design parameters, because they have a lot of redundancies, especially for long-span bridges. Cable-stayed bridges exhibit several nonlinear behaviors concurrently under normal design loads because of large displacements; the interaction among the pylons, the stayed cables, and the bridge deck; the strong axial and lateral forces acting on the bridge deck and pylons; and cable nonlinearity. A typical two-lane, three-span, steel box-girder cable-stayed bridge superstructure was selected for this paper. The numerical results indicate that, if the ratio of the main span length with respect to the total span length, L1∕L, is small, the structure usually has a higher critical load. If the ratio Ip∕Ib increases, the critical load of the bridge decreases, in which Ip is the moment of inertia of the pylon and Ib is the moment of inertia of the bridge deck. When the ratio Ip∕Ib is greater than 10.0, the decrement becomes insignificant. For cable arrangements, bridges supported by a harp-type cable arrangement are the better design than bridges supported by a fan-type cable arrangement on buckling analysis. The numerical results also indicate that use of either A-type or H-type pylons does not significantly affect the critical load of this type of structure. In order to make the numerical results useful, the buckling loads have been nondimensionalized and presented in both tabular and graphical forms.     

Optimization of Cable Tensioning in Cable-Stayed Bridges

During the structural analysis of cable-stayed bridges, some specific problems arise that are not common in other types of bridges. One of these problem is the derivation of an optimal sequence for the tensioning of the stay cables. This paper describes a novel solution to this problem, the unit force method. The method takes into account all relevant effects for the design of cable-stayed bridges, including construction sequence, second-order theory, large displacements, cable sag and time-dependent effects, such as creep and shrinkage or relaxation of prestressing tendons. Information about the implementation of this method into a computer program is given, and an example of a practical application of this method concludes this paper. The method is not restricted to the design of cable-stayed bridges and may well be used for other structural applications in the future.     

Number of Cable Effects on Buckling Analysis of Cable-Stayed Bridges

Cables instead of interval piers support cable-stayed bridges, and the bridge deck is subjected to strong axial forces due to the horizontal components of cable reactions. The structural behavior of a bridge deck becomes nonlinear because of the axial forces, large deflection, and nonlinear behavior of the cables and the large deformation of the pylons as well as their interactions. The locations and amplitude of axial forces acting on the bridge deck may depend on the number of cables. Agrawal indicated that the maximum cable tension decreases rapidly with the increase in the number of cables. This paper investigates the stability analysis of cable-stayed bridges and considers cable-stayed bridges with geometry similar to those proposed in Agrawal's paper. A digital computer and numerical analysis are used to examine 2D finite element models of these bridges. The eigen buckling analysis has been applied to find the minimum critical loads of the cable-stayed bridges. The numerical results indicate that the total cumulative axial forces acting on the bridge girder increase as the number of cables increases, yet because the bridge deck is subjected to strong axial forces, the critical load of the bridges decreases. Increasing the number of cables may not increase the critical load on buckling analysis of this type of bridge. The fundamental critical loads increase if the ratio of Ip∕Ib increases until the ratio reaches the optimum ratio. If the ratio of Ip∕Ib is greater than the optimum ratio, depending on the geometry of an individual bridge, the fundamental critical load decreases for all the types of bridges considered in this paper. In order to make the results useful, they have been normalized and represented in graphical form.     

Vulnerability Assessment of Cable-Stayed Bridges in Probabilistic Domain

Vulnerability of a structure under terrorist attack can be regarded as the study of its behavior against blast-induced loads. A structure is vulnerable if a small damage can trigger a disproportionately large consequence and lead to a cascade of failure events or even collapse. The performance of structural vulnerability depends upon factors such as external loading condition and structural properties. As many of these factors are random in nature, it is necessary to develop a vulnerability assessment technique in the probabilistic domain. In this study, one such assessment framework is proposed for cable-stayed bridges. The framework consists of two stages of analysis: determining the probability of direct damage due to blast loads and assessing the subsequent probability of collapse due to component damage. In the first stage assessment, damage of the bridge component is defined as the exceedance of a predefined limit state such as displacement or yielding. The damage probability is obtained through a stochastic finite-element analysis and the first-order second-moment reliability method. The second stage assessment further calculates the probability of collapse due to direct damage of some component via an event tree approach. The proposed assessment methods are illustrated on a hypothetical single-tower cable-stayed bridge. It is seen that the proposed methods provide a quantitative tool for analyzing the vulnerability performance of cable-stayed bridges under terrorist attack.     

Elastic-Plastic Seismic Behavior of Long Span Cable-Stayed Bridges

This paper investigates the elastic-plastic seismic behavior of long span cable-stayed steel bridges through the plane finite-element model. Both geometric and material nonlinearities are involved in the analysis. The geometric nonlinearities come from the stay cable sag effect, axial force-bending moment interaction, and large displacements. Material nonlinearity arises when the stiffening steel girder yields. The example bridge is a cable-stayed bridge with a central span length of 605 m. The seismic response analyses have been conducted from the deformed equilibrium configuration due to dead loads. Three strong earthquake records of the Great Hanshin earthquake of 1995 in Japan are used in the analysis. These earthquake records are input in the bridge longitudinal direction, vertical direction, and combined longitudinal and vertical directions. To evaluate the residual elastic-plastic seismic response, a new kind of seismic damage index called the maximum equivalent plastic strain ratio is proposed. The results show that the elastic-plastic effect tends to reduce the seismic response of long span cable-stayed steel bridges. The elastic and elastic-plastic seismic response behavior depends highly on the characteristics of input earthquake records. The earthquake record with the largest peak ground acceleration value does not necessarily induce the greatest elastic-plastic seismic damage.     

Influence of Secondary Elements and Deck Cracking on the Lateral Load Distribution of Steel Girder Bridges

The AASHTO LRFD load distribution factor equation was developed based on elastic finite element analysis considering only primary members, i.e., the effects of secondary elements such as lateral bracing and parapets were not considered. Meanwhile, many bridges have been identified as having significant cracking in the concrete deck. Even though deck cracking is a well-known phenomenon, the significance of pre-existing cracks on the live load distribution has not yet been assessed. The purpose of this research is to investigate the effect of secondary elements and deck cracking on the lateral load distribution of girder bridges. First, secondary elements such as diaphragms and parapets were modeled using the finite element method, and the calculated load distribution factors were compared with the code-specified values. Second, the effects of typical deck cracking and crack types that have a major effect on load distribution were identified through a number of nonlinear finite element analyses. It was established that the presence of secondary elements may produce load distribution factors up to 40% lower than the AASHTO LRFD values. Longitudinal cracking was found to increase the load distribution factor by up to 17% when compared to the LRFD value while the transverse cracking was found to not significantly influence the transverse distribution of moment.     

Fatigue Damage of Steel Bridges Due to Dynamic Vehicle Loads

This paper focuses on the fatigue damage caused in steel bridge girders by the dynamic tire forces that occur during the crossing of heavy transport vehicles. This work quantifies the difference in fatigue life of a short-span and a medium-span bridge due to successive passages of either a steel-sprung or an air-sprung vehicle. The bridges are modeled as beams to obtain their modal properties, and air-sprung and nonlinear steel-sprung vehicle models are used. Bridge responses are predicted using a convolution method by combining bridge modal properties with vehicle wheel forces. A linear elastic fracture mechanics model is employed to predict crack growth. For the short-span bridge, the steel-sprung vehicle caused fatigue failure up to 6.5 times faster than the air-sprung vehicle. For the medium-span bridge, the steel-sprung vehicle caused fatigue failure up to 277 times faster than the air-sprung vehicle.     

Dynamic Behavior of Steel Deck Tension-Tied Arch Bridges to Seismic Excitation

The dynamic responses of steel deck, tension-tied, arch bridges subjected to earthquake excitations were investigated. The 620 ft (189 m) Birmingham Bridge, located in Pittsburgh, was selected as an analytical model for the study. The bridge has a single deck tension-tied arch span and is supported by two bridge piers, which in turn are supported by the pile foundations. Due to the complex configuration of the deck system, two analytical models were considered to represent the bridge deck system. Using the normal mode method, seismic responses were calculated for two bridge models and the results were compared with each other. Three orthogonal records of the El Centro 1940 earthquake were used as input for the seismic response analysis. The modal contributions were also checked in order to obtain a reasonable representation of the response and to minimize computational cost. Displacements and stresses at the panel points of the bridge are calculated and presented in graphical form.     

Influence of Functionally Graded Material on Buckling of Skew Plates under Mechanical Loads

In this technical note, the critical buckling of simply supported functionally graded skew plate subjected to mechanical compressive loads is evaluated using first-order shear deformation theory in conjunction with the finite element approach. The material properties are assumed to vary in the thickness direction according to the power-law distribution in terms of volume fractions of the constituents. The effective material properties are estimated from the volume fractions and the properties of the constituents using the Mori–Tanaka homogenization method. The effects of aspect ratio, material gradient index, and skew angle on the critical buckling loads of functionally graded material plates are highlighted.     

Seismic Vulnerability and Mitigation during Construction of Cable-Stayed Bridges

The implications of earthquake loading during balanced cantilever construction of a cable-stayed bridge are examined. Finite-element models of a cable-stayed bridge were developed and multiple ground motion time history records were used to study the seismic response at the base of the towers for six stages of balanced cantilever construction. Probabilistic seismic hazard relationships were used to relate ground motions to bridge responses. The results show that there can be a high probability of having seismic responses (forces/moments) in a partially completed bridge that exceed, often by a substantial margin, the 10%/50-year design level (0.21% per annum) for the full bridge. The maximum probability of exceedance per annum was found to be 20%. This occurs because during balanced-cantilever construction the structure is in a particularly precarious and vulnerable state. The efficacy of a seismic mitigation strategy based on the use of tie-down cables intended for aerodynamic stability during construction was investigated. This strategy was successful in reducing some of the seismic vulnerabilities so that probabilities of exceedance during construction dropped to below 1% per annum. Although applied to only one cable-stayed bridge, the same approach can be used for construction-stage vulnerability analysis of other long-span bridges.     

Concrete Cracking in Tension Members and Application to Deck Slabs of Bridges

Currently, estimations of the crack width in the deck slab of bridges given by codes of practice are based on either theoretical or empirical approaches considering mainly the monotonic loading behavior. However, cracking in reinforced tensile members is highly influenced by the loading history (including both the loading and unloading processes) because of the irreversible nonlinear behavior of bond and of tensile response of concrete, resulting into residual cracks of non-negligible width. This paper investigates the influence of this phenomenon and presents a physical model describing it. An analytical model is developed and its results are compared to various tests with good agreement. Finally, a simple design formula is derived and recommendations for its application to practical cases are proposed.     

Live Load Distribution in Girder Bridges Subject to Oversized Trucks

A significant challenge facing motor carriers and engineers in this nation is the limitation of vehicle size and weight based on pavement and bridge capacity. However, the current demands of society and industry occasionally require a truck to carry a load that exceeds the size and weight of the legal limit. In these cases, engineering analysis is required before a permit is issued to ensure the safety of the structures and roadways on the vehicle's route. A truck with a wheel gauge larger than the standard 1.83 m (6 ft) gauge requires additional engineering effort because the wheel load girder distribution factors (GDFs) established by AASHTO cannot be used to accurately estimate the live load in the girders. In this study, the finite-element method is used to develop modification factors for the AASHTO flexure and shear GDFs to account for oversized trucks. The results of the analysis showed that the use of the proposed modification factors with the specification-based GDFs can help increase the allowable loads on slab-on-girder bridges.     

Laboratory Testing Material Property and FE Modeling Structural Response of PAM-Modified Concrete Overlay on Bridges

Portland cement concrete overlay on bridge deck is subjected to distresses of cracking and interface debonding under the effects of repeated vehicle loading and temperature cycling. In order to improve the overlay performance, this research used the polyacrylamide (PAM) polymer to modify the mechanical properties of concrete. The direct shear and impact resistance tests were designed to measure the interface bonding strength and dynamic performance, respectively. The comprehensive and flexural strength and three-point bending fatigue tests were conducted following the standards. Meanwhile, the three-dimensional finite-element (FE) models of the T-girder and box-girder bridges under the moving traffic loadings were built to analyze the stress response and improve the structural design. An analytical model of flexural stress was developed and validated the FE modeling results. A rubber cushion was designed in the FE model to “absorb” the flexural stress. Laboratory testing results indicate that PAM can significantly improve the flexural strength, bonding strength, impact resistance, and fatigue life of concrete. The modified concrete with 8% PAM by mass of cement poses higher flexural strength and impact resistance than concretes with other PAM percentages. FE simulation results indicate that there exists a critical overlay thickness inducing the maximum interface shear stress, which should be avoided in the structural design. The rubber cushion can effectively relieve the flexural stress.     

Distribution of Wheel Loads on Continuous Steel Spread-Box Girder Bridges

Composite concrete-steel spread (multispine) box girder bridges remain one of the most common types constructed. Current design practices in North America recommend few analytical methods for the design of such bridges in simply supported construction. However, the effects of continuous construction have not been dealt with fully. In designing a continuous bridge, it is important to determine the maximum negative and positive stresses, maximum reactions, and shears in the bridge subjected to various loadings. This paper presents an extensive parametric study using a finite-element model in which 60 continuous bridge prototypes of various geometries, each subjected to various loading conditions, are analyzed for the distribution of flexural stresses, deflection, shears, and reactions. The parameters considered in the study are span length, number of spread boxes, and number of lanes. Distribution factors for maximum flexural stresses, deflection, shears, and reactions, suitable for design, are deduced for AASHTO truck loading. Results from tests on five box girder bridge models verify the finite-element model. A design example is presented to illustrate the use of the deduced formulas for the distribution factors.     

Dynamic Behavior of Deck Slabs of Concrete Road Bridges

This paper treats the dynamic effect of traffic actions on the deck slabs of concrete road bridges using the finite-element method. All the important parameters that influence bridge-vehicle interaction are studied with a systematic approach. An advanced numerical model is described and the results of a parametric study are presented. The results suggest that vehicle speed is less important than vehicle mass and that road roughness is the most important parameter affecting the dynamic behavior of deck slabs. The type of bridge cross section was not found to have a significant influence on deck slab behavior. The dynamic amplification factor varied between 1.0 and 1.55 for the bridges and vehicles studied. These results should be validated by further work.     

Field Testing and Analysis of CRC Deck Girder Bridges

This paper presents findings of field tests and analysis of two conventionally reinforced concrete (CRC) deck girder bridges designed in the 1950s. The bridges are in-service and exhibit diagonal cracks. Stirrup strains in the bridge girders at high shear regions were used to estimate distribution factors for shear. Impact factors based on the field tests are reported. Comparison of field measured responses with AASHTO factors was performed. Three-dimensional elastic finite-element analysis was employed to model the tested bridges and determine distribution factors specifically for shear. Eight-node shell elements were used to model the decks, diaphragms, bent caps, and girders. Beam elements were used to model columns under the bent caps. The analytically predicted distribution factors were compared with the field test data. Finally, the bridge finite-element models were employed to compare load distribution factors for shear computed using procedures in the AASHTO LRFD and Standard Specifications.     

Dynamic Response of Plates on Elastic Foundation to Moving Loads

A procedure incorporating the finite strip method and a spring system has been developed and applied to treat the dynamic response of plate structure resting on an elastic foundation to moving loads. The response to a single moving concentrated load is first investigated and then the effects of velocity, elastic foundation stiffness, moving path, and distance between multiple moving loads are studied. The response under a moving harmonic load with constant velocity is finally treated and the effect of the load frequency is investigated. Results indicate that the foundation stiffness and the velocity and frequency of the moving load have significant effects on the dynamic response of the plate and on resonant velocities. Some of these findings might find use in practical applications.