XPS and optical studies of Xe-implanted and annealed YSZ single crystals

Xe⁺ ion implantation with 200 keV was completed at room temperature up to a fluence of 1 × 10¹⁷ ion/cm² in yttria-stabilized zirconia (YSZ) single crystals. Optical absorption and X-ray photoelectron spectroscopy (XPS) were used to characterize the changes of optical properties and charge state in the as-implanted and annealed crystals. A broad absorption band centered at 522 or 497 nm was observed in the optical absorption spectra of samples implanted with fluences of 1 × 10¹⁶ ion/cm² and 1 × 10¹⁷ ion/cm², respectively. These two absorption bands both disappeared due to recombination of color centers after annealing at 250 °C. XPS measurements showed two Gaussian components of O_1s spectrum assigned to Zr–O and Y–O, respectively, in YSZ single crystals. After ion implantation, these two peaks merged into a single peak with the increasing etching depth. However, this single peak split into two Gaussian components again after annealing at 250 °C. The concentration of Xe decreased drastically after annealing at 900 °C. And the XPS measurement barely detected the Xe. There was no change in the photoluminescence of YSZ single crystals with a fluence of 1 × 10¹⁷ ion/cm² after annealing up to 900 °C.     

Ion-induced electron emission – monitoring the structure transitions in graphite

The temperature dependence of ion-induced electron emission yield γ under 30 keV Ar⁺ ion impacts at incidence angles θ = 0−80° under dynamically steady-state conditions has been measured for polygranular graphite POCO-AXF-5Q. The fluencies were 10¹⁸–10¹⁹ ion/cm², the temperatures varied from the room temperature (RT) to 400 °C. The RHEED has shown that same diffraction patterns correspond to a high degree of disorder at RT. At high temperature (HT), some patterns have been found similar to those for the initial graphite surfaces. The dependence γ(T) has been found to be non-monotonic and for normal and near normal ion incidence manifests a step-like increase typical for a radiation induced phase transition. At oblique and grazing incidence (θ > 30°), a broad peak was found at T_p = 100 °C. An analysis based on the theory of kinetic ion-induced electron emission connects the behavior of γ(θ,T) to the dependence of both secondary electron path length λ and primary ion ionizing path length R_e on lattice structure that drastically changes due to damage annealing.     

Carbon ion-implanted optical waveguides in Nd:YLiF4 crystal: Refractive index profiles and thermal stability

We report on the optical planar waveguides in Nd:YLiF₄ laser crystals fabricated by 6.0 MeV C³⁺ ion implantation at doses of 1 × 10¹⁵ or 2.5 × 10¹⁵ ions/cm², respectively. The refractive index profiles, which are reconstructed according to the measured dark mode spectroscopy, show that the ordinary index had a positive change in the surface region, forming non-leaky waveguide structures. The extraordinary index is with a typical barrier-shaped distribution, which may be mainly due to the nuclear energy deposition of the incident ions into the substrate. In order to investigate the thermal stability of the waveguides, the samples are annealed at temperature of 200–300 °C in air. The results show that waveguide produced by higher-dose carbon implantation remains relatively stable with post-irradiation annealing treatment at 200 °C in air.     

Mechanism of dynamic strain aging and characterization of its effect on the low-cycle fatigue behavior in type 316L stainless steel

Low-cycle fatigue tests were carried out in air in a wide temperature range from 20 to 650 °C with strain rates of 3.2 × 10⁻⁵–1 × 10⁻² s⁻¹ for type 316L stainless steel to investigate dynamic strain aging (DSA) effect on the fatigue resistance. The regime of DSA was evaluated using the anomalies associated with DSA and was in the temperature range of 250–550 °C at a strain rate of 1 × 10⁻⁴ s⁻¹, in 250–600 °C at 1 × 10⁻³ s⁻¹, and in 250–650 °C at 1 × 10⁻² s⁻¹. The activation energies for each type of serration were about 0.57–0.74 times those for lattice diffusion indicating that a mechanism other than lattice diffusion is involved. It seems to be reasonable to infer that DSA is caused by the pipe diffusion of solute atoms through the dislocation core. Dynamic strain aging reduced the crack initiation and propagation life by way of multiple crack initiation, which comes from the DSA-induced inhomogeneity of deformation, and rapid crack propagation due to the DSA-induced hardening, respectively.     

Effect of annealing on the optical absorption of Ni nanoparticles in MgO single crystals

Ni⁺ ion implantation with an energy of 64 keV in MgO single crystals was conducted at room temperature up to a fluence of 1 × 10¹⁷ ion/cm². The as-implanted crystals were annealed isochronally at temperatures up to 900 °C. Optical absorption spectroscopy, X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) have been utilized to characterize the changes of optical properties and the microstructure of the annealed samples. XPS results showed that the charge state of implanted Ni was still mainly in metallic Ni⁰ after annealing at 900 °C. TEM analysis revealed metallic Ni nanoparticles with depth-dependant dimensions of 1–10 nm in the annealed sample. Optical absorption spectroscopy indicated that the Ni nanoparticles exhibited a broad surface plasmon resonance absorption band in annealed samples and the band shifted to a longer wavelength with the increasing annealing temperature.     

Surface morphology of the Ar ion-irradiated Ag/Si(1 1 1) system

In the present study, a 500 Å thin Ag film was deposited by thermal evaporation on 5% HF etched Si(1 1 1) substrate at a chamber pressure of 8×10⁻⁶ mbar. The films were irradiated with 100 keV Ar⁺ ions at room temperature (RT) and at elevated temperatures to a fluence of 1×10¹⁶ cm⁻² at a flux of 5.55×10¹² ions/cm²/s. Surface morphology of the Ar ion-irradiated Ag/Si(1 1 1) system was investigated using scanning electron microscopy (SEM). A percolation network pattern was observed when the film was irradiated at 200°C and 400°C. The fractal dimension of the percolated pattern was higher in the sample irradiated at 400°C compared to the one irradiated at 200°C. The percolation network is still observed in the film thermally annealed at 600°C with and without prior ion irradiation. The fractal dimension of the percolated pattern in the sample annealed at 600°C was lower than in the sample post-annealed (irradiated and then annealed) at 600°C. All these observations are explained in terms of self-diffusion of Ag atoms on the Si(1 1 1) substrate, inter-diffusion of Ag and Si and phase formations in Ag and Si due to Ar ion irradiation.     

Surface regrowth of Sb ion implanted Si(100)

Thermal regrowth of a Si(100) surface, damaged by 80 keV Sb implantation, was monitored by angular resolved photoemission (ARUPS), Rutherford backscattering (RBS) and channelling. It was found that regrowth in UHV at 650°C does not result in a well ordered surface. Annealing at higher temperatures (700–1100°C) results in densities of surface defects of (2.5 ± 0.4) × 10¹⁵ at./cm². A well ordered Si(100)2 × 1 reconstructed surface can be formed only after removal of a 10 nm thick layer by Ne ion bombardment, and heat treatment at 600°C. These observations can be explained by the formation of a surface layer with misoriented domains simultaneously with the solid phase epitaxy.     

Formation of cavities in GaAs and InGaAs

The ion implantation of He is examined as a means to form thermally stable cavities in GaAs. Room-temperature implantation of 2–10 × 10¹⁶ He/cm² at 40 or 50 keV forms bubbles, but subsequent annealing at 250°C or above leads to exfoliation of the implanted surface layer. The exfoliation appears related to the agglomeration of bubbles on dislocations at the back of the layer; evidence suggests these may be misfit dislocations formed to relieve compressive stress in the implanted layer. Implantation of He at 150°C produces similar results, whereas the He diffuses out of GaAs without forming cavities during implantation at 300°C. However, implantations of immobile Ar followed by He at 400°C produce extended defects with bubbles in the implanted layer; the He can be degassed by subsequent annealing at 400°C to produce 1.5–3.5 nm cavities that are stable at this temperature. The same treatment applied to an In_0.10Ga_0.90As/GaAs heterostructure produces larger cavities preferentially located on dislocations at the interface, with only slight reduction in strain of the epitaxial layer. The microstructures of both GaAs and the heterostructure clearly demonstrate an attractive interaction between bubbles or cavities and dislocations.     

The excitation power density effect on the Si nanocrystals photoluminescence

In the present work we have studied the photoluminescence (PL) behavior from Si nanocrystals (NCs) as a function of the excitation power density and annealing time. The NCs were produced in a SiO₂ matrix by Si implantations from room temperature (RT) up to 700 °C, followed by post-annealing in N₂ atmosphere at high temperature. With this aim we have changed the excitation power density (from 2 × 10⁻³ W/cm² up to 15 W/cm²) and the annealing time (from 10 min up to 15 h). The strong PL signal, which at 15 W/cm² is composed by a single-peak structure (650–1000 nm) centered at around 780 nm, expands up to 1200 nm showing a two-peak structure when measured at 20 × 10⁻³ W/cm². The peak structure located at the short wavelength side is kept at 780 nm, while the second peak, starting at around 900 nm, redshifts and increases its intensity with the implantation temperature and annealing time. The effect of the annealing time on the PL spectra behavior measured at low excitation power agrees by the first time with the Si NC growth according to quantum confinement effects.     

Elemental dissolution study of Pu-bearing borosilicate glasses

Single-pass flow-through tests were conducted to study the effects of self-radiation damage from alpha decay on dissolution kinetics of three radiation-aged Pu-bearing (1 mass% PuO₂) borosilicate glasses over a pH interval of 9–12 at 80–88 °C. The chemical compositions of the glasses were identical except the ²³⁹Pu/²³⁸Pu isotopic ratio, which was varied to yield accumulated doses of 1.3 × 10¹⁶, 2.9 × 10¹⁷ and 2.6 × 10¹⁸ -decays/g at the time of testing. Release of Al, B, Cs, Na, Si and U to solution increased with increasing pH, whereas Ca, Pu and Sr were invariant over the pH interval. Average dissolution rates, based on B release, were identical within experimental uncertainty for all three glass compositions and increased from 0.17 ± 0.07 at pH(23 °C) 9 to 10.6 ± 2.7 (g/(m² d¹)) at pH(23 °C) 12. Release rates of Pu were 10²- to 10⁵-fold slower compared to all other elements and were not affected by isotopic composition, self-radiation damage sustained by the glass, or pH. These data demonstrate that self-radiation damage does not affect glass dissolution rates, despite exposure to internal radiation doses for >20 years.     

Development of uranium carbide targets for the on-line production of neutron-rich isotopes

A number of on-line and off-line tests have been performed at the IRIS (investigation of radioactive isotopes at synchrocyclotron) facility in order to develop uranium carbide targets with a high density (11 g/cm³) for the on-line production of neutron-rich isotopes by fission of ²³⁸U. A 1 GeV proton beam was used to bombard two kinds of targets held at temperatures in the range of 1900–2100 °C. The first one was a target-ion source assembly slightly modified to withstand 3 months of continuous heating at a temperature of about 2050 °C. The second unit was of a new kind, where ionisation takes place in the target volume itself. A comparison of the on-line isotopic yields before and after heating for 3 months is here reported. The yields and release times of Rb, Cs and In are compared with the ones obtained from a standard reference target, as measured in previous experiments.     

Optical behaviour of Er doped rutile by ion implantation

Rutile single crystals were implanted at room temperature with fluences of 5 × 10¹⁵ Er⁺/cm² ions with 150 keV energy. Rutherford backscattering/channeling along the 0 0 1 axis reveals complete amorphization of the implanted region. Photoluminescence reveals the presence of an optical centre close to the intra-ionic emission of Er³⁺ in the as-implanted samples. After annealing at 800 °C in air no changes were observed in the aligned RBS spectrum. On the contrary, annealing in reducing atmosphere (vacuum) induces the epitaxy of the damage layer. These results are unexpected, since for implantations of other ions under the same conditions, epitaxial recrystallization of the damage region occurs at this temperature. On the other hand, photoluminescence studies show the presence of new Er-related optical centres with high thermal stability in the samples annealed under oxidizing conditions. Annealing at 1000 °C in vacuum leads to the complete recrystallization of the damaged region. At this temperature a large fraction of Er segregates to the surface.     

RBS studies of the lattice damage caused by 1 Me V Si implantation into Al0.3Ga0.7As/GaAs superlattices at elevated temperature

The lattice damage accumulation in GaAs and Al_0.3Ga_0.7As/GaAs superlattices by 1 MeV Si⁺irradiation at room temperature and 350°C has been studied. For irradiations at 350°C, at lower doses the samples were almost defect-free after irradiation, while a large density of accumulated defects was induced at a higher dose. The critical dose above which the damage accumulation is more efficient is estimated to be 2 × 10¹⁵ + Si/cm² for GaAs, and is 5 × 10¹⁵ Si/cm² for Al_0.8Ga_0.7As/GaAs superlattice for implantation with 1.0 MeV Si ions at 350°C. The damage accumulation rate for 1 MeV Si ion implantation in Al_0.3Ga_0.7As/GaAs superlattice is less than that in GaAs.     

Low temperature epitaxial regrowth of mercury implanted sapphire

Hg ions were implanted into sapphire at room temperature and 80 keV energy to a fluence of 1 × 10¹⁵ Hg⁺ / cm². This fluence was enough to produce an amorphous surface layer. The annealing behaviour was studied combining RBS/channeling and hyperfine interaction techniques. Surprisingly, the RBS/channeling results show there is an epitaxial regrowth of the damaged layer after annealing at 800°C for 20 min. Although some of the implanted Hg segregates to the surface during the epitaxial regrowth, a significant fraction is incorporated into regular sites along the c-axis. The hyperfine interactions results, obtained after implantation of a dose of 5 × 10¹² Hg⁺ / cm², show that a small fraction of Hg is probably bound to oxygen. This result is in agreement with the RBS/channeling measurements which also show that the system formed after annealing is stable even at high temperatures.     

Large-area deposition of biaxially textured YSZ buffer layers using an IBAD-process

An ion-beam-assisted deposition technique (IBAD), using two Kaufman ion sources with diameters of 11 cm, was employed to grow biaxially textured YSZ buffer layers. They serve as a template for YBCO films and as a diffusion barrier. The best YSZ films on small Al₂O₃ substrates show good in-plane alignment characterized by a FWHM of 10.8° in (111)-Φ-scan. An improvement of texture with rising film thickness was observed saturating at 8.5°. On 100 cm² large substrates the texture was within a range of 15° to 24°. First improvements of the homogeneity were achieved by a four-time rotating of 90° of the substrate holder around the substrate normal during deposition. On polycrystalline PSZ substrates with YSZ buffers YBCO films with a critical current j_c > 10⁶ A/cm² (at 77 K, 0 T) were deposited.     

Mechanism of irradiation assisted stress corrosion crack initiation in thermally sensitized 304 stainless steel

Thermally sensitized 304 stainless steels, irradiated up to 1.2 × 10²¹ n/cm² (E > 1 MeV), were slow-strain-rate-tensile tested in 290 °C water containing 0.2 ppm dissolved oxygen (DO), followed by scanning and transmission electron microscopic examinations, to study mechanism of irradiation-assisted-stress-corrosion-crack (IASCC) initiation. Intergranular (IG) cracking behaviors changed at a border fluence (around 1 × 10²⁰ n/cm²), above which deformation twinning were predominant and deformation localization occurred earlier with increasing fluence. The crack initiation sites tended to link to the deformation bands, indicating that the crack initiation may be brought about by the deformation bands interacted with grain boundaries. Thus the border fluence is equivalent to the IASCC threshold fluence for the sensitized material, although the terminology of IASCC is originally given to the non-sensitized materials without microstructural definition. The IASCC threshold fluence was found to change with irradiation conditions. Changes in IASCC susceptibility and IASCC threshold fluence with fluence and DO were further discussed.     

Influence of ageing heat treatment on alloy A-286 microstructure and stress corrosion cracking behaviour in PWR primary water

The influence of ageing heat treatment on alloy A-286 microstructure and stress corrosion cracking behaviour in simulated Pressurized Water Reactor (PWR) primary water has been investigated. A-286 microstructure was characterized by transmission electron microscopy for ageing heat treatments at 670 °C and 720 °C for durations ranging from 5 h to 100 h. Spherical γ′ phase with mean diameters ranging from 4.6 to 9.6 nm and densities ranging from 8.5 × 10²² m⁻³ to 2 × 10²³ m⁻³ were measured. Results suggest that both the γ′ phase mean diameter and density quickly saturate with time for ageing heat treatment at 720 °C while the γ′ mean diameter increases significantly up to 100 h for ageing heat treatment at 670 °C. Grain boundary η phase precipitates were systematically observed for ageing heat treatment at 720 °C even for short ageing periods. In contrast, no grain boundary η phase precipitates were observed for ageing heat treatments at 670 °C except after 100 h. Hardening by γ′ precipitation was well described by the dispersed barrier hardening model with a γ′ barrier strength of 0.23. Stress corrosion cracking behaviour of A-286 was investigated by means of constant elongation rate tensile tests at 1.5 × 10⁻⁷ s⁻¹ in simulated PWR primary water at 320 °C and 360 °C. In all cases, initiation was transgranular while propagation was intergranular. Grain boundary η phase precipitates were found to have no significant effect on stress corrosion cracking. In contrast, yield strength and to a lesser extent temperature were found to have significant influences on A-286 susceptibility to stress corrosion cracking.     

Carbon clustering in Si1−xCx formed by ion implantation

Silicon-carbon alloys were formed by multiple energy implantation of C⁺ ions in silicon and in Silicon on Sapphire (SOS). The ion fluence ranged between 5 × 10¹⁶ − 3 × 10¹⁷ ions/cm² and the energy between 10–30 keV in order to obtain constant carbon concentration into a depth of 100 nm. The carbon atomic fraction (x) was in the range 0.22–0.59 as tested by Rutherford backscattering spectrometry (RBS). Thermal annealing of the implanted films induced a transition from amorphous to a polycrystalline structure at temperatures above 850°C as detected by Infrared spectrometry (IR) in the wavenumber range 600–900 cm⁻¹. The optical energy gap and the intensity of the infrared signal after annealing at 1000°C depended on the film composition: they both increased linearly with carbon concentration reaching a maximum at the stoichiometric composition (x = 0.5). At higher carbon concentration the IR intensity saturated and the optical energy gap decreased from the maximum value of 2.2 to 1.8 eV. The behaviour at the high carbon content has been related to the formation of graphitic clusters as detected by Raman spectroscopy.     

Separation of plutonium from lanthanum by electrolysis in LiCl–KCl onto molten bismuth electrode

This work presents a study on the electroseparation of plutonium from lanthanum using molten bismuth electrodes in LiCl–KCl eutectic at 733 K. The reduction potentials of Pu³⁺ and La³⁺ ions were measured on a Bi thin film electrode using cyclic voltammetry (CV). A difference between the peak potentials for the formation of PuBi₂ and LaBi₂ of approximately 100 mV was found. Separation tests were then carried out using different current densities and salt phase compositions between a plutonium rod anode and an unstirred molten Bi cathode in order to evaluate the efficiency of an electrolytic separation process. At a current density of 12 mA/cm²/wt% (Pu³⁺), only Pu³⁺ ions are reduced into the molten Bi electrode, leaving La³⁺ ions in the salt melt. Similar results were found at two different Pu/La concentration ratios ([Pu]/[La] = 4 and 10). At a current density of 26 mA/cm²/wt% (Pu³⁺), co-reduction of Pu and La was observed as expected by the large negative potential of the Bi cathode during the separation test.     

Photoluminescence of Au formed in 12CaO · 7Al2O3 single crystal by Au-implantation

Au⁺ ion implantation with fluences from 1 × 10¹⁴ to 3 × 10¹⁶ cm⁻² into 12CaO · 7Al₂O₃ (C12A7) single crystals was carried out at a sample temperature of 600 °C. The implanted sample with the fluence of 1 × 10¹⁵ cm⁻² exhibited photoluminescence (PL) bands peaking at 3.1 and 2.3 eV at 150 K when excited by He–Cd laser (325 nm). This was the first observation of PL from C12A7. These two PL bands are possibly due to intra-ionic transitions of an Au⁻ ion having the electronic configuration of 6s², judged from their similarities to those reported on Au⁻ ions in alkali halides. However, when the concentration of the implanted Au ions exceeded the theoretical maximum value of anions encaged in C12A7 (2.3 × 10²¹ cm⁻³), surface plasmon absorption appeared in the optical absorption spectrum, suggesting Au colloids were formed at such high fluences. These observations indicate that negative gold ions are formed in the cages of C12A7 by the Au⁺ implantation if an appropriate fluence is chosen.