Effect of heat treatment on microstructure and mechanical properties of Cr–Ni–Mo–Nb steel

Abstract

The microstructure and mechanical properties of a medium carbon Cr–Ni–Mo–Nb steel in quenched and tempered conditions were investigated using transmission electron microscopy (TEM), X-ray analysis, and tensile and impact tests. Results showed that increasing austenitisation temperature gave rise to an increase in the tensile strength due to more complete dissolution of primary carbides during austenitisation at high temperatures. The austenite grains were fine when the austenitisation temperature was <1373 K owing to the pinning effect of undissolved Nb(C,N) particles. A tensile strength of 1600 MPa was kept at tempering temperatures up to 848 K, while the peak impact toughness was attained at 913 K tempering, as a result of the replacement of coarse Fe rich M₃C carbides by fine Mo rich M₂C carbides. Austenitisation at 1323 K followed by 913 K tempering could result in a combination of high strength and good toughness for the Cr–Ni–Mo–Nb steel.     

Effect of processing parameters on the microstructure and mechanical properties of Al–steel composite foam

Al–steel composite foams comprise of steel hollow spheres embedded in an aluminum matrix and are processed using a gravity casting technique. The effect of processing parameters such as casting temperature and cooling rate on the microstructure and mechanical behavior was studied to establish structure–property relationships. Results show that the amount and composition of intermetallic phases present in the foam microstructure is directly related to casting temperature and cooling rate. Highest strength and energy absorption were obtained from Al–steel foams with fast solidification rates that minimize the growth of intermetallic phases.     

Effect of strain rate on microstructures and mechanical properties of Fe–18Cr–8Ni steel

The effect of strain rate on deformation microstructures and mechanical properties of Fe–18Cr–8Ni austenitic stainless steel was investigated at strain rates of from 10^?3 to 100?s^?1. The results indicated that the deformation mechanism of steel changes from transformation induced plasticity (TRIP) to TRIP?+?twinning induced plasticity (TWIP) effect when the strain rate is increased from 10^?3 to 100?s^?1. The yield strength of steel increases gradually with strain rate increased, while the tensile strength and elongation first decreases and then increases slowly. The changes in tensile strength and elongation are due to the change of deformation mechanism with the strain rate increased.     

Microalloying effects on microstructure and mechanical properties of 18Cr–2Mo ferritic stainless steel heavy plates

The microstructure, including grain size and precipitation, tensile strength and Charpy impact toughness of (Nb + V) 18Cr–2Mo ferritic stainless steel heavy plates with/without Ti were investigated by means of optical microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction and standard tensile strength and Charpy impact toughness testing. It was found that for 18Cr–2Mo heavy plate, a good combination of Nb–V stabilized method without Ti induces refinement of grain sizes due to the precipitation of amounts of fine Nb carbonitrides and V nitrides. Meanwhile, the mechanical testing results indicate that optimal transformation of grain size, precipitation that Nb–V composition system brings to 18Cr–2Mo heavy plate is beneficial to improvement of strength and impact toughness.     

Effect of thermomechanical treatment parameters on mechanical properties of duplex ferrite–martensite structure in dual phase steel

Abstract

The quantitative effects of the variables used in the thermomechanical treatment (TMT) of a dual phase steel, in the temperature region of intercritical annealing, have been studied by statistical design of experiments. The initial microstructure has tremendous influence on the final microstructure and properties of the steel. The kinetics of transformation is enhanced by the deformation process as has been evidenced by optical and TEM microstructures. The mechanical properties such as tensile strength, yield stress, and relative elongation have been correlated with the TMT parameters and are brought out in the form of regression equations. Percentage phase of ferrite or martensite formed owing to thermomechanical treatment by two different routes has also been quantified in the form of regression equations. The adequacies of the equations were assessed by a Fisher F test and the accuracies of the equations have been further verified by performing random experiments in the range of variation of the variables. Isoproperty lines have been constructed using the regression equations developed. The equations can predict the properties within the range of variation of the variables.     

Effect of friction welding parameters on mechanical and metallurgical properties of aluminium alloy 5052–A36 steel joint

Abstract

The mechanical and metallurgical properties of friction welded joints between type 5052 aluminium alloy and type A36 steel have been studied in the present work. Joint strength increased with increasing upset pressure and friction time until it reached a crictical value. The strength of the joint settled at a lower value, compared with that of the base metal, in the case of increasing friction time, caused by the formation of an intermediate phase (intermetallic compound, oxides). The microstructure of 5052 alloy was greatly deformed near the weld interface, and underwent dynamic recrystallisation owing to frictional heat and deformation resulting from the friction welding process. Therefore, a very fine and equiaxed grain structure was observed near the interface. Elongated grains were observed outside the dynamic recrystallisation region at the peripheral part, while the A36 steel side was not deformed. The hardness of the near interface was slightly softer than that of the 5052 alloy base metal, and maximum softened width was ~8 mm from the interface. In the present work, the conditions of friction time t ₁ = 0.5 s and upset pressure P ₂ = 137.5 MPa gave maximum joint strength of 202 MPa when the friction pressure, upset time and rotation speed were fixed at 70 MPa, 5 s and 2000 rev min^-1, respectively, and these were the optimum friction welding conditions for the aluminium alloy 5052-A36 steel joint.     

Effect of holding time on vacuum brazing for a stainless steel plate–fin structure

This paper presents a vacuum brazing of 304 stainless steel plate–fin structures with nickel-based BNi-2 filler metal. The effect of brazing holding time on tensile strength and microstructure has been investigated, aiming to obtain the optimal brazing holding time. The microstructure in brazing joint consists of diffusion-affected zone (DAZ), interface reaction zone (IRZ), isothermally solidified zone (ISZ) and athermally solidified zone (ASZ). The structure in the fillet is composed of solid solution, nickel silicon, nickel boron compound and a mixture with nickel silicon and nickel boron. The tensile strength increases along with the increase of holding time, but decreases when the holding time is over 25 min. A maximum tensile strength of 65.1 MPa is obtained with 25 min holding time. Too short holding time will make boron diffuse insufficiently and generate a great deal of brittle boride components, and too long holding time will make the base metal dissolve into the filler metal excessively and creates more corrosion voids.     

Effect of heat treatment on microstructure and mechanical properties of a new β high strength titanium alloy

Microstructure and mechanical properties of a new β high strength Ti–3.5Al–5Mo–6V–3Cr–2Sn–0.5Fe titanium alloy were investigated in this paper. Both the α/β and β solution treatment and subsequent aging at temperatures ranging from 440 °C to 560 °C for 8 h were introduced to investigate the relationship between microstructures and properties. Microstructure observation of α/β solution treatment plus aging condition shows that the grain size is only few microns due to the pinning effect of primary α phase. The β solution treatment leads to coarser β grain size and the least stable matrix. The size and volume fraction of secondary α are very sensitive to temperature and strongly affected the strength of the alloy. When solution treated at 775 °C plus aged at 440 °C, the smallest size (0.028 μm in width) of secondary α and greatest volume fraction (61%) of α resulted in the highest yield strength (1624 MPa). And the yield strength decreased by an average of 103 MPa with every increase of 40 °C due to the increase of volume fraction and decrease of the size of secondary α. In β solution treatment plus aging condition, tensile results shows that the strength if the alloy dramatically decreased by an average of 143 MPa for every increase of 40 °C because of larger size of secondary α phase than α/β solution treated plus aged condition.     

Effect of processing routes on mechanical and thermal properties of copper–graphene composites

In this paper, copper–graphene composites were fabricated by using two different processing routes (ball milling (BM) and ultrasonication) followed by spark plasma sintering. Vickers hardness and anisotropic thermal conductivity of the composites were measured and observed that ultrasonicated fabricated composites gave better result compared with BM composite and even from pure copper. The hardness values obtained for ultrasonicated copper–graphene composite were 69?HV (57% higher) and thermal conductivity 387?W/m?K (13% higher) by using only 0.5?wt-% of graphene, while for pure copper the values were 44?HV and 341?W/m?K. The value of anisotropic thermal conductivity ultrasonicated composites was also 1.97 which is much higher than pure copper 0.94.     

Effect of cobalt nanoparticles on mechanical properties of Sn–58Bi solder joint

Brittle phases are responsible for crack formation and propagation in tin–bismuth (Sn–58Bi) solder material. The purpose of this work is to investigate the effects of various cobalt (Co) nanoparticle (NP) concentrations on the tensile properties of the Sn–58Bi solder matrix. Different aging times were studied to find out the effect of Co NP on ultimate tensile strength. Tin–bismuth solder joints of different Co NP concentrations of 0%, 0.5%, 1%, and 2% were prepared. The reflow process was done at 180 °C for 1 min. Scanning Electron Microscopy and Energy-Dispersive X-ray spectroscopy were used to analyze the solder joints. The tensile test was carried out for the Sn–58Bi and Sn–58Bi–xCo (x?=?0.5, 1, and 2) solder joints. The tensile test was run before and after aging time. The tensile results reveal that the addition of Co NP increased the tensile strength significantly at different concentrations of Co NP. The Tensile test revealed that ductility was improved as the temperature was increased. As the aging time increased, the ultimate tensile strength of all samples decreased.

     

Effect of Si content on microstructure and mechanical properties of Al–Si–Mg alloys

Microstructure and mechanical properties of as-cast and as-extruded Al–Si–Mg alloys with different Si content are investigated by tensile test, microstructure observation. High density of Si particles in the Al alloys can induce dynamic recrystallization during hot extrusion and it becomes more matured with an increase in the density of Si particles. The tensile strength of as-cast and as-extruded alloys can be improved with the increase of Si content and hot extrusion make the elongation of alloys increase dramatically. Considerable grain refining effect caused by recrystallization occurred during hot extrusion of S2 (equivalently commercial A356 alloy) and S3 (near eutectic alloy) alloys plays an important role in the improvement of elongation. A good combination of strength and elongation for the as-extruded S3 alloy indicates that near eutectic Al–Si alloys can be hot-extruded to produce aluminum profiles with high performance.     

Effect of the POSS–Polyimide nanostructure on its mechanical and electrical properties

Nanocomposite films consisted of Polyhedral Oligomeric Silsesquioxane (POSS) filler in a Polyimide (PI) matrix were prepared. The effect of the nanocomposites’ structure on its mechanical and electrical properties was evaluated with respect to survival in the low Earth orbit (LEO) environment. The POSS–PI structure consists of POSS nano-aggregates formed in the bulk and on the surface. The aggregates’ size and distribution are POSS content-dependant. The fracture mechanism during hypervelocity impact at extreme temperature conditions was studied. The hypervelocity impacts of the POSS–PI films result in a brittle fracture, compared to ductile fracture in the case of PI, and in formation of radial cracks. A model based on formation and coalescence of voids around the aggregates, when load is applied, is suggested to explain the effect of the POSS content on the POSS–PI fracture mechanism. The size and density of the POSS aggregates also affect the nanocomposite’s volume electrical resistivity. An inverse dependence exists between the POSS aggregates’ surface density and the nanocomposites’ volume electrical resistivity.     

Effect of microstructure on the fatigue properties of Ti–6Al–4V titanium alloys

Through an analysis on microstructure and high cycle fatigue (HCF) properties of Ti–6Al–4V alloys which were selected from literature, the effects of microstructure types and microstructure parameters on HCF properties were investigated systematically. The results show that the HCF properties are strongly determined by microstructure types for Ti–6Al–4V. Generally the HCF strengths of different microstructures decrease in the order of bimodal, lamellar and equiaxed microstructure. Additionally, microstructure parameters such as the primary α (α_p) content and the α_p grain size in bimodal microstructures, the α lamellar width in lamellar microstructure and the α grain size in equiaxed microstructures, can influence the HCF properties.     

Effect of calcinations of starting powder on mechanical properties of hydroxyapatite–alumina bioceramic composite

The effect of calcinations of starting powder on the mechanical properties of hydroxyapatite (HA)-based bioceramic composite was investigated. The calcinations of HA powder in air at 900 °C increased the crystallinity as well as the size of the powder. Ball milling after the calcinations was effective in eliminating large agglomerates in the powder. When the powder was mixed with reinforcing Al₂O₃ powder, the mixture became fine and homogeneous. The flexural strength of HA–Al₂O₃ composite was increased by the calcinations processes at all the Al₂O₃ concentration. However, the fracture toughness was not much influenced by the calcinations. These results lead to the conclusion that the calcinations process effectively reduced the critical flaw size in the body by removing the agglomerates in the HA powder.     

Effect of pulse-current heating multiple forging on mechanical properties of Mg–Nd–Zn–Zr alloy

The effects of pulse current heating on microstructure evolution and mechanical property of Mg–Nd–Zn–Zr magnesium alloy during multiple forging are investigated. The results of uniaxial tensile test show that tensile strength, yield strength and elongation of the alloy are improved with the increasing of forging passes. Moreover, under the condition of pulse current heating, this promotion effect is more obvious. The results of microstructure analysis show that recrystallisation occurs during the deformation, and the recrystallisation is obviously accelerated by pulse current. The magnesium alloy billet with fine grains is obtained eventually. Theoretical analysis shows that pulse current can increase the recrystallisation nucleation rate and reduce the rate of grain growth, which is helpful to refine the grains of alloy.     

Influence of welding parameters on microstructures and mechanical properties of electron beam welded aluminium–lithium plates

Abstract

The present work focused on the welding characteristics of electron beam welding (EBW) in 8090 Al–Li plates, evaluated in terms of strength or toughness degradation in post-weld impact and bending tests with loading rates of 10³, 10^-1, and 10^-4 s^-1. The influence of welding parameters, such as welding power, welding speed, and electron beam focus position, on the post-weld microstructures, porosity, and mechanical properties were examined. Although the joint efficiency for the maximum flexure strength (F_p ), or tensile strength, can be as high as 85–90%, the joint efficiency for the fracture absorption energy (E_t ) was only 20–40%, a level usually unsuitable for applications. It was found that changing the welding power and speed by a factor of 3 resulted in significant variation in E_t but only minor variation in F_p . Changing the welding focus position had little effect on post- weld mechanical properties. The abundant grain boundary precipitates in the welded specimens were thought to be the main cause of the degraded post-weld properties. Other microstructural factors included the δ′ precipitate and grain sizes. The volume fraction of porosity did not play any decisive role owing to the small size (<0·3 mm), low quantity (1–2%), and spherical shape of the EBW induced pores. Finally, given the same post-weld microstructures, the toughness degradation of the EBW specimens was worst under high rate impact loading.     

Effect of Ce on microstructures and mechanical properties of rapidly solidified Mg–Zn alloy

Abstract

The rapidly solidified (RS) Mg–Zn based alloys with Ce addition were produced via atomising the alloy melt and subsequent splat quenching on the water cooled copper twin rollers in the form of flakes. The effects of Ce additions on the microstructures, phase compositions, thermal stability and isochronal age hardening behaviour of the RS Mg–Zn alloy were systematically investigated. The RS Mg–6Zn alloy is characterised by fine grains in the size of 6–10 μm and is composed of α-Mg, Mg₅₁Zn₂₀ and a small quantity of MgZn₂ and Mg₂Zn₃ phases. With the increment of Ce, the microstructures of the alloys are refined, and the volume fractions of dispersions are increased remarkably. The stable intermetallic compounds, i.e. the Mg_xZn_yCe_z ternary phases, are formed in the RS Mg–Zn–Ce alloys at the expense of the Mg₅₁Zn₂₀ phases, which leads to the enhanced thermal stability of the alloys, especially for the Mg–6Zn–5Ce alloy. In the alloy, the atomic percentage ratio of Zn/Ce in the Mg_xZn_yCe_z phase is close to two, and the maximum hardness is 91·5±7 HV after annealing at 200°C for 1 h. However, the age hardening behaviour of the alloys decreases with the increment of Ce, and the main reason is discussed.     

Effect of MWCNT alignment on mechanical and self-monitoring properties of extruded PET–MWCNT nanocomposites

Self-monitoring aligned MWCNT loaded PET composites, with different CNT content, were prepared via twin-screw extrusion starting from a PET/MWCNT masterbatch, and fully characterized. All electrically conductive samples showed self-monitoring ability, i.e. a variation in electrical resistance as a function of stress. Moreover, the insertion of MWCNTs resulted in mechanical reinforcement with respect to neat PET. It was found that both self-monitoring behavior and mechanical performance are directly related to MWCNT content and to the direction of applied stress with respect to CNT orientation. In particular, too high MWCNT content decreased sensitivity at low strain, whereas a minimum MWCNT content was required to insure ohmic conductivity.     

Effect of filler type on the mechanical properties of self-reinforced polylactide–calcium phosphate composites

Bioabsorbable polymers are of interest as internal fracture fixation devices. Self-reinforcement has been developed to improve the mechanical properties of the material and the addition of calcium phosphate fillers improves the bioactivity. Composite plates, produced by compression molding preimpregnated sheets of polylactide fibers coated in a polylactide matrix have been degraded in simulated body fluid for up to 12 weeks. Some samples also contained hydroxyapatite or tricalcium phosphate filler particles. Degradation was measured by monitoring the water uptake and mass decrease of the samples, as well as carrying out four point bend tests to assess the mechanical properties of the material. By 12 weeks, it was found that the unfilled samples absorbed more water and showed greater mass loss than the samples containing calcium phosphate fillers. Also, the flexural modulus and yield stress decreased significantly at week 12 for the unfilled samples. Adding hydroxyapatite (HA) or tricalcium phosphate (TCP) to the composite increased the flexural modulus and yield strength to values within the range of those reported for cortical bone and these values were maintained over the 12-week period.     

Effect of aluminium on the microstructure and mechanical properties of as-cast magnesium–manganese alloys

In this paper, the effect of aluminium on microstructure and mechanical properties of as-cast magnesium–manganese alloy has been investigated by means of X-ray diffraction, optical microscopy and scanning electron microscopy. The results reveal that various Al–Mn intermetallic compounds form with an increase of Al content. As a result, microstructure of AM11 alloy has been effectively refined due to the formation of Al₈Mn₅ phase along the grain boundary, while Al addition is explained as the main reason on refining the microstructure of AM91 alloy due to its higher grain growth restriction factor value of ～4.32. The tensile yield strength (TYS) has been improved steadily from 27.4 to 122.9?MPa with increasing Al content, because of the combined effects of grain boundary strengthening, solid solution strengthening and precipitation hardening behaviours.