Study on thermal oxidative stabilization reactions of poly(acrylonitrile‐co‐itaconic acid) copolymers synthesized at different polymerization stages

The structural evolution of poly(acrylonitrile‐co‐itaconic acid) (PAI) copolymers synthesized at different polymerization stages during thermal oxidative stabilization (TOS) are quantitatively tracked by the attenuated total reflection Fourier transform infrared spectroscopy technology. The evolution of β‐amino nitrile and conjugated nitrile are quantitatively tracked by peak‐fitting technique during TOS. A procedure is developed to get the fine information of TOS reactions, especially to value qualitatively the length of cyclic or ladder structures. There is no distinguished difference of structural evolution of PAI copolymers synthesized at different polymerization stages during TOS process. The length of cyclic or ladder structures for all PAI copolymers possesses almost the same values and decreases gradually as the TOS proceeding. The termination of cyclization and the oxidative dehydrogenation become dominant in the late of TOS process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45245.     

Characterization of polyacrylonitrile,poly(acrylonitrile‐co‐vinyl acetate), and poly(acrylonitrile‐co‐itaconic acid) based activated carbon nanofibers

In this study, three different acrylonitrile (AN)‐based polymers, including polyacrylonitrile (PAN), poly(acrylonitrile‐co‐vinyl acetate) [P(AN‐co‐VAc)], and poly(acrylonitrile‐co‐itaconic acid) [P(AN‐co‐IA)], were used as precursors to synthesize activated carbon nanofibers (ACNFs). An electrospinning method was used to produce nanofibers. Oxidative stabilization, carbonization, and finally, activation through a specific heating regimen were applied to the electrospun fibers to produce ACNFs. Stabilization, carbonization, and activation were carried out at 230, 600, and 750 °C, respectively. Scanning electron microscopy, thermogravimetric analysis (TGA), and porosimetry were used to characterize the fibers in each step. According to the fiber diameter variation measurements, the pore extension procedure overcame the shrinkage of the fibers with copolymer precursors. However, the shrinkage process dominated the scene for the PAN homopolymer, and this led to an increase in the fiber diameter. The 328 m²/g Brunauer–Emmett–Teller surface area for ACNFs with PAN precursor were augmented to 614 and 564 m²/g for P(AN‐co‐VAc) and P(AN‐co‐IA), respectively. The TGA results show that the P(AN‐co‐IA)‐based ACNFs exhibited a higher thermal durability in comparison to the fibers of PAN and P(AN‐co‐VAc). The application of these copolymers instead of AN homopolymer enhanced the thermal stability and increased the surface area of the ACNFs even in low‐temperature carbonization and activation processes. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44381.     

Dilute solution viscosity properties of high molar mass poly(acrylonitrile‐co‐itaconic acid)

The intrinsic viscosities [η] and viscosity constants of high molar mass poly(acrylonitrile‐co‐itaconic acid) copolymer in DMF were obtained by the methods of Huggin, Fuoss, Martin and Schulz‐Blaschke. The values of [η] by averaging procedures suggested by Sakai were close to those from Huggins method. There was an abnormal positive deviation from the rectilinearity of the reduced viscosity (η_red) versus concentration (c) plot in all the cases in the dilute regime, which was attributed to the polyelectrolytic effect. This was further confirmed by the analysis by Fuoss method. The deviation from the Huggins dependence is discussed for a good solvent (DMF) alone and in the presence of a non‐solvent, methanol. The deviation cross‐over points c′ and c″ changed with molecular weight, and the concentration range greater than c″ and less than c* was taken for a more reliable determination of intrinsic viscosity. The non‐solvent played a key role in determining the polymer–polymer interactions. The Huggins coefficient increased and the cross‐over points c′ and c″ shifted to higher concentration regime as the mixed solvent became poorer. The inter‐ and intra‐polymer interactions increased in the presence of methanol. In poor solvent, the enhanced intramolecular interactions caused the polymer to shrink in size, causing a reduction in [η] and hydrodynamic volume. Copyright © 2003 Society of Chemical Industry     

Mechanical properties of poly(N‐isopropyl‐acrylamide‐co‐itaconic acid) hydrogels

Hydrogels of N‐isopropylacrylamide and itaconic acid were synthesized with different monomer ratios and with two crosslinking agent concentrations. The different xerogels were immersed in water and the swelling process was conducted up to equilibrium conditions at two temperatures (22 and 37°C). These temperatures are lower and higher than the transition temperature shown by PNIPA hydrogels. The mechanical properties of the different solvated hydrogels were examined by oscillatory shear measurements at 22 and 37°C. The copolymer volume fraction and the elastic storage modulus of the hydrogels decreased as the itaconic acid percentage in the copolymer increased. This behavior was attributed to the higher hydrophilic character of the itaconic acid comonomer. Effective crosslinking density, molar mass between crosslinks, and the polymer–solvent interaction parameter were determined from the experimental values of the elastic storage moduli and the copolymer volume fractions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2540–2545, 2002     

Degradation of poly(D,L‐lactic acid)‐b‐poly(ethylene glycol) copolymer and poly(L‐lactic acid) by electron beam irradiation

This article investigated the effects of electron beam (EB) irradiation on poly(D ,L ‐lactic acid)‐b‐poly(ethylene glycol) copolymer (PLEG) and poly(L ‐lactic acid) (PLLA). The dominant effect of EB irradiation on both PLEG and PLLA was chain scission. With increasing dose, recombination reactions or partial crosslinking of PLEG can occur in addition to chain scission, but there was no obvious crosslinking for PLLA at doses below 200 kGy. The chain scission degree of irradiated PLEG and PLLA was calculated to be 0.213 and 0.403, respectively. The linear relationships were also established between the decrease in molecular weight with increasing dose. Elongation at break of the irradiated PLEG and PLLA decreased significantly, whereas the tensile strength and glass transition temperature of PLLA decreased much more significantly compared with PLEG. The presence of poly(ethylene glycol) (PEG) chain segment in PLEG was the key factor in its greater stability to EB irradiation compared with PLLA. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

ZnBr2‐catalyzed chemical effects in poly(acrylonitrile‐ co‐butadiene)

The excellent chemical properties and resistance to oil of poly(acrylonitrile‐co‐butadiene), or nitrile–butadiene rubber (NBR), has led to the extensive use of these elastomers as O‐ring material in the oil extraction industry. The degradation of NBR gaskets is known to occur during the well completion and oil extraction process when they are exposed to bromide fluids such as ZnBr₂‐based completion fluid. Samples of NBR, polyacrylonitrile, and polybutadiene were exposed to ZnBr₂‐based completion fluid and analyzed by attenuated total reflectance (ATR) and diffuse reflectance IR. These analyses showed that the ZnBr₂ completion fluid promoted the hydrolysis of the nitrile group to form amides and carboxylic groups. The carbon–carbon double bonds in NBR were unaffected after short exposure to ZnBr₂‐based completion fluid but were quickly hydrated in acidic bromide mixtures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1250–1257, 2003     

Fourier transform infrared and wide‐angle X‐ray diffraction studies of the thermal cyclization reactions of high‐molar‐mass poly(acrylonitrile‐co‐itaconic acid)

The stabilization reactions of a high‐molar‐mass poly(acrylonitrile‐co‐itaconic acid) precursor in air at 200, 220, and 240°C were studied with Fourier transform infrared. Principally, the cyclization of nitrile groups leading to the ladder structures of tetrahydropyridine occurred. Evidence for oxidative reactions causing the conversion of the C? C structure to C?C and generating groups such as ? OH and C?O was also obtained. As the temperature of stabilization was increased, the rate of the reaction increased without causing great changes in the Fourier transform infrared spectral patterns. The maximum nitrile conversion achievable was limited by the temperature of stabilization. Although the reaction stagnated at 40 and 80% at 200 and 220°C, it was practically complete in about an hour at 240°C. Higher temperatures also favored the formation of extended conjugated structures. Wide‐angle X‐ray diffraction studies of the polymer stabilized at 300 and 400°C in argon confirmed that the aromatization index value and the crystallinity of the polymer increased proportionally to the temperature of pyrolysis. An analysis of the wide‐angle X‐ray diffraction pattern and the elemental composition of the stabilized polymer implied the formation of the tetrahydropyridine structure at 400°C. The higher pyrolysis temperature favored the formation of the lattice constituted by this group. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3055–3062, 2006     

High char‐yielding poly[acrylonitrile‐co‐(itaconic acid)‐co‐(methyl acrylate)]: synthesis and properties

Polyacrylonitrile terpolymers of various compositions consisting of acrylonitrile (AN), itaconic acid (IA) and methyl acrylate (MA) were synthesized by solution polymerization in dimethylsulfoxide. Increase in concentration of either IA or MA retarded the overall polymerization rate and the polymer molecular weight. The system consisting of AN + MA and varying IA concentration was more prone to retardation in comparison with the system composed of AN + IA with variable MA concentration. The retardation factors were quantified. Minor quantities of MA boost the reactivity of IA in the terpolymer system. The terpolymer was richer in MA vis‐à‐vis the feed. The thermal characteristics of the terpolymer were examined as a function of its composition. In contrast to the copolymer of AN and IA requiring 1–1.5 mol% IA, the terpolymer required an IA content of approximately 2.5 mol% for optimum thermal stability. The polymer with 90 mol% AN, 2.5 mol% IA and 7.5 mol% MA exhibited reasonably good char‐forming characteristics and thermal stability. The overall crystallinity and crystallite size of the polymers were found to decrease on incorporation of the comonomers. The ‘aromatization index’ of the copolymer increased with the temperature of pyrolysis through re‐organization of the tetrahydropyridine ladder structure. Copyright © 2005 Society of Chemical Industry     

Compatibilization of starch/poly(butylene adipate‐co‐terephthalate) blown films using itaconic acid and sodium hypophosphite

Itaconic acid (IA) has potential as a compatibilizing agent in polymeric blends due to its unique chemical characteristics. Sodium hypophosphite (SHP) has been studied as a catalyst in esterifying reactions using multicarboxylic acids. Starch/poly(butylene adipate‐co‐terephthalate) blown films containing IA, with and without SHP, were produced. The film containing IA presented higher tensile strength (8.166 MPa) and elongation (891.473%) than the control film (5.548 MPa and 487.637%, respectively). When SHP was added (sample IA‐SHP), tensile strength increased even more (9.215 MPa); however, elongation (636.821%) was lower than in the IA film. This behavior was attributed to crosslinking between two starch itaconoate molecules intermediated by SHP. The increase in the compatibility between the polymeric phases justified the lower permeability to water vapor of the IA‐SHP films and was responsible for the production of films with a more compact and homogeneous structure. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46629.     

Multilayer composite surfaces prepared by an electrostatic self‐assembly technique with quaternary ammonium salt and poly(acrylic acid) on poly(acrylonitrile‐co‐acrylic acid) membranes

An electrostatic self‐assembly technique was applied to prepare ion complex polymer layers on polyacrylonitrile with acrylic acid segments {poly(acrylonitrile‐co‐acrylic acid) [P(AN‐co‐AA)]}. For the ionic complex layers, quaternary ammonium salts, such as cetyl trimethyl ammonium chloride (CTAC) and tetramethyl ammonium chloride (TMAC), were used as cationic species, and also, poly(acrylic acid) (PAA) was used as an anionic species. These cationic and anionic species were self‐assembled alternately on the surface of the P(AN‐co‐AA) membrane. Fourier transform infrared spectroscopy, AFM, and water contact angle measurements of the membrane surface were used to confirm the formation of the multilayer composites on the P(AN‐co‐AA). The permeabilities of water and macromolecules of different molecular weights were evaluated by a membrane filtration technique. The values of permeability strongly depended on the formation layer by layer of these ion composites on the base P(AN‐co‐AA). Through the measurement of the values of the contact angle of water, it was clear that surface nature of the base membrane treated by CTAC or TMAC and PAA dramatically changed. We concluded that such an electrostatic self‐assembly technique is useful for the preparation of multicomposite layers to modify the surface of base P(AN‐co‐AA) membranes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Determination of swelling behavior and morphological properties of poly(acrylamide‐co‐itaconic acid) and poly(acrylic acid‐co‐itaconic acid) copolymeric hydrogels

Poly(acrylamide‐co‐itaconic acid) (PAAmIA) and poly(acrylic acid‐co‐itaconic acid) (PAAIA) copolymeric hydrogels were prepared with different compositions via free‐radical polymerization. Ethylene glycol dimethacrylate (EGDMA) was used as an original crosslinker for these monomers. Gelation percentages of the monomers were studied in detail and it was found that addition of IA into the monomer mixture decreased the gelation percentage. The variation in swelling values (%) with time, temperature, and pH was determined for all hydrogels. PAA, which is the most swollen hydrogel, has the swelling percentage value of 2000% at pH = 7.4, 37°C. Swelling behaviors were explained with detailed SEM micrographs, which show the morphologic differences between dry and swollen hydrogels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5994–5999, 2006     

Electrospinning of solvent‐resistant nanofibers based on poly(acrylonitrile‐co‐glycidyl methacrylate)

This article reports on the preparation of novel solvent‐resistant nanofibers by electrospinning of poly(acrylonitrile‐co‐glycidyl methacrylate) (PANGMA) and subsequent chemical crosslinking. PANGMA nanofibers with diameters ranging from 200 to 600 nm were generated by electrospinning different solutions of PANGMA dissolved in N,N‐dimethylformamide. Different additives were added to reduce the fiber diameter and improve the morphology of the nanofibers. The as‐spun PANGMA nanofibers were crosslinked with 27 wt % aqueous ammonia solution at 50°C for 3 h to gain the solvent resistance. Swelling tests indicated that the crosslinked nanofibers swelled in several solvents but were not dissolved. The weight loss of all the crosslinked nanofibrous mats immersed in solvents for more than 72 h was very low. The characterization by electron microscopy revealed that the nanofibrous mats maintained their structure. This was also confirmed by the results of the pore size measurements. These novel nanofibers are considered to have a great potential as supports for the immobilization of homogeneous catalysts and enzymes. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of oxalic acid on the rheological properties of dope solution of poly[acrylonitrile‐co‐(methyl acrylate)‐co‐(itaconic acid)]

The very high dope viscosity of concentrated dope of poly[acrylonitrile‐co‐(methyl acrylate)‐co‐(itaconic acid)] (with M?_v = 10.67 × 10⁵g mol^?1) in DMF could be diminished significantly by the addition of oxalic acid (OXA). The change in steady shear rheological behaviour caused by OXA has been analysed for the dope using a rheometer working in the viscosity mode. The temperature dependence of η₀ conformed to the Arrhenius‐Frenkel‐Eyring equation. ΔG_v decreased marginally with OXA concentration, and the least value was observed at an OXA concentration of 0.63 % by weight. Shear thinning behaviour was observed under higher shear rates for the terpolymer solutions in the presence and absence of OXA. The pseudoplasticity index (n) showed an abrupt initial increase on addition of OXA. The OXA concentration of 0.63 % by weight was advantageous for decreasing the viscosity of the polymer dope. The reduction in viscosity is attributed to the disturbed polymer‐polymer interactions by way of H‐bonding of OXA with the polymer. OXA‐containing dope at higher shear rate could achieve very low viscosities. Copyright © 2004 Society of Chemical Industry     

Synthesis and properties of poly(acrylonitrile‐co‐p‐trimethylsilylstyrene) and poly(acrylonitrile‐co‐p‐trimethylsilylstyrene‐co‐styrene)

Copolymerization of acrylonitrile (AN) with p‐trimethylsilylstyrene (TMSS) was carried out at 60°C in bulk and in solution in the presence of 2,2′‐azobisisobutyronitrile (AIBN). The reactivity ratios of AN (M₁) and TMSS (M₂) were determined to be r₁ = 0.068 and r₂ = 0.309. The effects of the AIBN concentration and that of the chain transfer agent CCl₄ on the molecular weights (MWs) of the copolymers were investigated. An increase in the concentrations of AIBN or CCl₄ in solution led to a decrease in MW. Poly(AN‐co‐TMSS‐co‐St) was synthesized in solution using AIBN as the initiator. The molar fraction of AN was 0.415, while the molar ratio of TMSS/St varied from 1 : 1 to 1 : 9. The transition temperatures and thermal and thermooxidative stabilities of poly(AN‐co‐TMSS) and poly(AN‐co‐TMSS‐co‐St) were investigated. The differential scanning calorimeter technique was used to determine the compatibility of the poly(AN‐co‐TMSS) and poly(AN‐co‐TMSS‐co‐St) with commercial poly(AN‐co‐St). All the blends show a single glass transition temperature, which indicates the compatibility of the blend components. The surface film morphology of the blends mentioned above was examined by X‐ray photoelectron spectroscopy. The data obtained indicate that the silicon‐containing copolymer is concentrated in the surface layer. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1920–1928, 2000     

Fourier transform near‐infrared and electron spin resonance studies on the crosslinking reaction of liquid carboxylated poly(acrylonitrile‐co‐butadiene) rubber with dicumyl peroxide in dioxane

The crosslinking reaction of liquid carboxylated poly(acrylonitrile‐co‐butadiene) [or nitrile rubber (NBR); acrylonitrile = 10 wt %] with dicumyl peroxide (DCPO) was studied in dioxane by means of Fourier transform near‐infrared spectroscopy (FT‐NIR) and electron spin resonance spectroscopy (ESR). Among the three butadiene units (1,2, cis‐1,4, and trans‐1,4 units) of NBR, only the pendant vinyl group of the 1,2 unit showed an absorption at 6110 cm^?1 from the FT‐NIR examination of dioxane solutions of NBR, 1‐octene, 3,3‐dimethyl‐1‐butene, trans‐2‐octene, cis‐5‐octen‐1‐ol, poly‐cis‐1,4‐butadiene, and poly‐1,2‐butadiene. The crosslinking reaction was followed in situ in dioxane by the monitoring of the disappearance of the pendant vinyl double bond with FT‐NIR. The initial disappearance rate (R₀) of the vinyl group was expressed by R₀ = k[DCPO]^0.9[NBR]^?0.2 (120°C). The overall activation energy of the reaction was calculated to be 20.7 kcal/mol. This unusual rate equation suggests unimolecular termination due to degradative chain transfer and depressed reactivity of the vinyl group caused by crosslinking. ESR study of the reaction mixture revealed that an allyl‐type polymer radical was formed in the reaction, and its concentration increased with time and was then saturated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2095–2101, 2003     

Thermal hydrolysis of poly(l‐lactic acid) films and cytotoxicity of water‐soluble degradation products

In this study, the thermal hydrolysis of the poly(l ‐lactic acid) (PLLA) films was investigated for its potential use as a food‐packaging ecomaterial. The surface morphology, mass loss, molecular weight, thermal properties, and medium pH were routinely investigated; meanwhile, in particular, the composition and cytotoxicity of the water‐soluble degradation products were studied. The changes in the mass loss and molecular weight revealed a random chain‐scission mechanism. Differential scanning calorimetry analysis implied that the hydrolysis preferentially took place in the amorphous region. The medium pH decreased with time because of the accumulation of acid water‐soluble products in the medium. Liquid chromatography/mass spectrometry analysis proved that these products were composed of 1–13 lactic acid units, in which the content of l ‐lactic acid increased with time and reached 9.71 mmol/L after hydrolysis for 84 days. The in vitro cell culture indicated that the water‐soluble degradation products from the PLLA films had no cytotoxicity to human umbilical vein endothelial cells. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42064.     

Compatibility and thermal properties of poly(acrylonitrile–butadiene–styrene) copolymer blends with poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile)

The mechanical and heat‐resistant properties of acrylonitrile–butadiene–styrene (ABS) binary and ternary blends were investigated. The relationship of compatibility and properties was discussed. The results show that poly(methyl methacrylate) (PMMA) and styrene–maleic anhydride (SMA) can improve the thermal properties of conventional ABS. The Izod impact property of ABS/PMMA blends increases significantly with the addition of PMMA, whereas that of ABS/SMA blends decreases significantly with the addition of SMA. Blends mixed with high‐viscosity PMMA are characterized by higher heat‐distortion temperature (HDT), and their heat resistance is similar to that of blends mixed with SMA. For high‐viscosity PMMA, from 10 to 20%, it is clear that blends appear at the brittle–ductile transition, which is related to the compatibility of the two phases. TEM micrographs show low‐content and high‐viscosity PMMA in large, abnormally shaped forms in the matrix. Compatibility between PMMA and ABS is dependent on both the amount and the viscosity of PMMA. When the amount of high‐viscosity PMMA varied from 10 to 20 wt %, the morphology of the ABS binary blends varied from poor to satisfactory compatibility. As the viscosity of PMMA decreases, the critical amount of PMMA needed for the compatibility of the two phases also decreases. SMA, as a compatibilizer, improved the interfacial adhesiveness of ABS and PMMA, which results in PMMA having good dispersion in the matrix. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2652–2660, 2002     

Investigation of thermal behavior of poly(2‐hydroxyethyl methacrylate‐co‐itaconic acid) networks

The thermal behavior of poly(2‐hydroxyethyl methacrylate) [PHEMA] homopolymer and poly(2‐hydroxyethyl methacrylate‐co‐itaconic acid) [P(HEMA/IA)] copolymeric networks synthesized using a radiation‐induced polymerization technique was investigated by differential scanning calorimetry, thermogravimetric analysis, and Fourier transform infrared spectroscopy. The glass‐transition temperature (T_g) of the PHEMA homopolymer was found to be 87°C. On the other hand, the T_g of the P(HEMA/IA) networks increased from 88°C to 117°C with an increasing amount of IA in the network system. The thermal degradation reaction mechanism of the P(HEMA/IA) networks was determined to be different from the PHEMA homopolymer, as confirmed by thermogravimetric analysis. It was observed that the initial thermal degradation temperature of these copolymeric networks increased from 271°C to 300°C with IA content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1602–1607, 2007     

Molecularly imprinted poly(acrylonitrile‐co‐acrylic acid) matrix with sclareol

There are presented results regarding a new set of molecularly imprinted polymers (MIPs) based on acrylonitrile:acrylic acid (AN:AA) copolymer matrix. As template, it was used sclareol, an important anticancer bioactive compound, never used before for molecular imprinting. An emerging and insufficient studied MIP preparation method, namely the phase inversion, was used to prepare 0.8 mm spherical sclareol MIPs (S‐MIPs). Three AN:AA copolymers, having the initial monomer ratios 90:10, 80:20, and 70:30, were synthesized by radical copolymerization in emulsion, without emulsifier. After that, each copolymer was dissolved in the presence of the template (sclareol) in dimethylformamide. The imprinting and the morphology of these new materials were analyzed by rheology, elemental analysis, infrared spectroscopy, size exclusion chromatography, thermogravimetric analysis, differential scanning calorimetry, batch rebinding tests, and Scatchard analysis. The conclusion was that the AN:AA‐80:20 matrix proved to be the optimized solution between high rigidity (given by the AN segments) and high affinity for the template (given by AA segments), the average imprinting factor for this system being 2.67. POLYM. ENG. SCI., 54:1484–1494, 2014. © 2013 Society of Plastics Engineers     

Chemical structure of poly(β‐cyclodextrin‐co‐citric acid)

We synthesized water‐insoluble polymers, poly(β‐cyclodextrin‐co‐citric acid)s, by heating a mixture of citric acid, cyclodextrin (CD), and Na₂HPO₄ as a catalyst with a 6 : 1 : 2 molar ratio at 160, 170, and 180°C for 10 and 20 min. The chemical composition of the polyesters was determined by high pressure liquid chromatography (HPLC) analysis of the polymer hydrolysates. The crosslinking mechanisms and thermal degradation of the polymers were also investigated. The polyesters contained 30–35% citric acid, 1–4% unsaturated carboxylic acids (i.e., itaconic, cis‐aconitic, trans‐aconitic, and mesaconic acids), and 60–70% CD, whereas about 40% of them were able to form inclusion complexes. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011