Effect of the casting solvent on the free‐volume characteristics and gas permeability of poly[1‐(trimethylsilyl)‐1‐propyne] membranes

The effect of the casting solvent on the structure of poly[1‐(trimethylsilyl)‐1‐propyne] (PTMSP) membranes was investigated experimentally. The PTMSP membranes were cast from solutions of cyclohexane, toluene, and tetrahydrofuran; the membranes were characterized by the positron annihilation lifetime spectroscopy (PALS) technique and by gas‐permeation measurements of O₂, N₂, and CO₂. The decay curves from the positron annihilation lifetime spectroscopy gave the best fit when two long‐life components (τ₃ and τ₄, τ₃ < τ₄) were employed. This suggests that two types of free volume existed in the PTMSP membranes. The size and number density of τ₄, which was characteristic for PTMSP, decreased in the following order of the casting solvents: cyclohexane > toluene > tetrahydrofuran. The order was consistent with the order of gas permeability. A good correlation was observed between the permeability and the structural parameter that denoted the free‐volume size and the number density of τ₄. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 497–501, 2003     

Partial crosslinking method for poly(2,6‐dimethyl‐1,4‐phenylene oxide)–poly(vinyl alcohol) membranes to obtain optimized stability and permeability

A partial crosslinking method was developed to modify hydrophilic membranes. The membrane was sandwiched between two porous plates to protect part of the areas, then immersed into a crosslinking solution such as glutaraldehyde, and finally, set free from the plates. The protected and unprotected areas were alternatively distributed to form a heterogeneous membrane. The unprotected areas were crosslinked to enhance the membrane stability, whereas the protected areas retained their original permeability. Three types of hydrophilic base membranes were selected and prepared from poly(2,6‐dimethyl‐1,4‐phenylene oxide) and poly(vinyl alcohol). The base membranes were partially crosslinked (5.56% of the direct area with enlarged areas) to investigate their stability and diffusion dialysis (DD) performances. The partially crosslinked membranes had remarkably reduced water uptake and swelling degrees compared with the base membranes (72.4–250.4 vs 178.2%–544.4% and 94.0%–408.0% vs. 163.8%–814.8%). Meanwhile, the membranes still retained high DD performances for separating HCl–FeCl₂ or NaOH–NaAlO₂ solutions. The dialysis coefficients of HCl and NaOH were much higher than those of the fully crosslinked membranes (0.0209 vs. 0.0109 m/h and 0.0059–0.0085 vs. 0.0017–0.0022 m/h). Hence, partial crosslinking was effective in optimizing the membrane hydrophilicity and permeability. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45305.     

Co‐extruded polymeric films for gas separation membranes

In recent years, gas separation has become an important step in many production process streams and part of final products. Through the use of melt co‐extrusion and subsequent orientation methods, gas separation membranes were produced entirely without the use of solvents, upon which current methods are highly dependent. Symmetric three layer membranes were produced using poly(ether‐block‐amide) (PEBA) copolymers, which serve as a selective material that exhibits a high CO₂ permeability relative to O₂. Thin layers of PEBA are supported by a polypropylene (PP) layer that is made porous through the use of two methods: (1) inorganic fillers or (2) crystal phase transformation. Two membrane systems, PEBA/(PP + CaCO₃) and PEBA/β‐PP, maintained a high CO₂/O₂ selectivity while exhibiting reduced permeability. Incorporation of an annealing step either before or after orientation improves the membrane gas flux by 50 to 100%. The improvement in gas flux was a result of either elimination of strain induced crystallinity, which increases the selective layer permeability, or improvement of the PP crystal structure, which may increase pore size in the porous support layer. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39765.     

Effect of operation conditions in the pervaporation of ethanol–water mixtures with poly(1‐trimethylsilyl‐1‐propyne) membranes

Poly(1‐trimethylsilyl‐1‐propyne) (PTMSP) is known to show preferential permeation of ethanol in the pervaporation of ethanol–water mixture. Although this polymer presents good characteristics for the separation of organic–water solutions, operation conditions and membrane characteristics, such as thickness, affect its pervaporation performance. The effect of temperature and feed concentration on pervaporation was studied. During pervaporation of 10 wt % ethanol–water solution, the separation factor (α_H2O^EtOH) remains almost constant, whereas the permeation flux (F) increases exponentially with operation temperature. On the other hand, the separation factor decreases, whereas the permeation flux increases with ethanol content in the feed mixture. The membrane thickness also affects the performance of PTMSP polymer films: selectivity increases sharply with membrane thickness up to 50 μm, whereas it remains constant for thicker membranes. The permeation flux decreases with membrane thickness in the whole range studied. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94:1395–1403, 2004     

Waterborne poly(urethane‐urea) gas permeation membranes for CO2/CH4 separation

In this work, dense membranes from aqueous dispersions of poly(urethane‐urea) (PUU) based on poly(propylene glycol) (PPG) and a block copolymer composed of poly(ethylene glycol) (PEG) and poly(propylene glycol) (PPG), EG‐b‐PG, with 7 wt % of the former were obtained. Nonpolluting formulations were synthesized with proportions of PPG and EG‐b‐PG as 1:0, 1:1, 1:3, and 3:1 in terms of equivalent number ratios. The effect of small and gradual increases in PEG segments was evaluated for the permeability of pure CO₂, CH₄, and N₂, at room temperature. Slight increases in PEG‐based segments in PUU promoted some remarkable properties, which led to a simultaneous increase in CO₂ permeability and ideal selectivity for CH₄ (300%) and N₂ (380%). Infrared spectroscopy showed that the PEG portions induced hydrogen bonds between ? NH of urethane and ether groups in the PEG portions, which promoted ordering of the flexible segments, confirmed by X‐ray diffractometry and small‐angle X‐ray scattering. Diffractometry techniques also confirmed the absence of crystalline domains, as did dynamic mechanical analysis. The produced membranes showed performance above Robeson's 2008 upper bound and seemed to be a superior polymeric material for CO₂/CH₄ and CO₂/N₂ separation. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46003.     

High‐performance PDMS membranes for pervaporative removal of VOCs from water: The role of alkyl grafting

To improve the pervaporation performance of PDMS membrane, alkyl groups with different chain length were grafted into PDMS matrix. The prepared membranes were characterized by ATR‐IR, DSC, TGA, PALS, and tensile testing. The effects of alkyl grafting on pervaporation performance of PDMS membrane were investigated in separation of ethyl acetate/water mixture. Experimental results show that the separation factor of PDMS membrane is largely improved by alkyl grafting because of the enhanced preferential sorption of ethyl acetate, and this improvement depends on alkyl grafting ratio and alkyl chain length. The total flux of PDMS membrane reduces after alkyl grafting owing to the decreased free volume. When grafting ratio is above 6.9%, membrane grafted with shorter alkyl groups is preferred for pervaporation. The best pervaporation performance is achieved by 9% octyl grafted PDMS membranes with a separation factor of 592 and a total flux of 188 gm^?2 h^?1 in separation of 1% ethyl acetate/water mixture at 40 °C. Moreover, this octyl grafted PDMS membrane also exhibits excellent separation performance in removal of butyl acetate, methyl‐tert‐butyl ether, and n‐butanol from water. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43700.     

Fourier transform infrared spectroscopy study of poly(1‐trimethylsilyl‐1‐propyne) aging

The influence of various factors on the aging of poly(1‐trimethylsilyl‐1‐propyne) (PTMSP) during long‐term storage in air was investigated with Fourier transform infrared spectroscopy. Most attention was paid to the differentiation of oxidation, the reduction of the free volume, and the absorption of low‐molecular‐weight compounds from the environment. IR spectra of PTMSP samples stored from 1–2 months to 6.5 years revealed C?O, C? O, and C? H bands that had been earlier attributed to polymer oxidation products. It was established, however, that these bands completely disappeared from IR spectra of the aged samples after their soaking in ethanol. Spectra of dried residues of ethanol extracts displayed all these bands and did not show any bands of polymer chain fragments. Gas chromatography/mass spectrometry analysis proved that the residues were composed mainly of various dialkyl phthalates. Special experiments showed that PTMSP films easily absorbed di‐n‐butyl phthalate vapors. IR spectra of the films stored for a long time showed no decrease in double‐bond and methyl group bands. It was concluded that the polymer did not undergo oxidation in air at room temperature for at least 6.5 years. The absorption of plasticizer vapors (and possibly other compounds) from the environment and the reduction of the free volume were the main reasons found for PTMSP aging. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2523–2527, 2007     

Effects of synthesis conditions on the pervaporation properties of poly[1‐(trimethylsilyl)‐1‐propyne] useful for membrane bioreactors

An integrated fermentation and membrane‐based recovery (pervaporation) process has certain economical advantages in continuous conversion of biomass into alcohols. This article presents new pervaporation data obtained for poly[1‐(trimethylsilyl)‐1‐propyne] (PTMSP) samples synthesized in various conditions. Three different catalytic systems, TaCl₅/n‐BuLi, TaCl₅/Al(i‐Bu)₃, and NbCl₅ were used for synthesis of the polymers. It was found that the catalytic system has a significant influence over the properties of membranes made from PTMSP. Although a combination of a high permeation rate and a high ethanol–water separation factor (not less than 15) was provided by all PTMSP samples, the PTMSP samples synthesized with TaCl₅/n‐BuLi showed significant deterioration of membrane properties when acetic acid was present in the feed. In contrast, the PTMSP samples synthesized with TaCl₅/Al(i‐Bu)₃ or NbCl₅ showed stable performance in the presence of acetic acid. When using a multicomponent mixture of organics and water, the copermeation of different organic components results in lower separation factor for both ethanol and butanol. These data are consistent with nanoporous morphology of PTMSP. It was demonstrated that pervaporative removal of ethanol improved the overall performance of the fermentation process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2271–2277, 2004     

Matrix effect of mixed‐matrix membrane containing CO2‐selective MOFs

Facilitated mixed‐matrix membranes (MMMs) containing Cu‐metal organic frameworks (Cu‐MOFs) with high CO₂ selectivity on an asymmetric polysulfone support were fabricated and examined the effect of gas separation performance using different matrices. An amorphous poly(2‐ethyl‐2‐oxazoline) (POZ) and semicrystalline poly(amide‐6‐b‐ethylene oxide) (PEBAX^®MH 1657) block copolymer were chosen as the polymeric matrix and the effect of the matrix on CO₂ separation for MMMs containing Cu‐MOFs was investigated. The interaction of CO₂ in different matrix was investigated theoretically using the density functional theory method, and it was found that the amide segment in PEBAX would contribute more to the CO₂ solubility than ether segment. The morphological changes were investigated by differential scanning calorimetry, field emission scanning electron microscope and X‐ray diffractometer. The ideal selectivity of CO₂/N₂ was enhanced significantly with the addition of a Cu‐MOF, and the values are higher in the Cu‐MOF/PEBAX MMM compared with that in a POZ based asymmetric MMM. Improvement in the CO₂/N₂ selectivity of a Cu‐MOF/PEBAX MMM was achieved via facilitated transport by the CO₂‐selective Cu‐MOFs due to both their high adsorption selectivity of CO₂ over N₂ and the decreased crystallinity of PEBAX due to the presence of the Cu‐MOFs, which would provide a synergic effect on the CO₂ separation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42853.     

Strontium(II) ion uptake on poly(N‐vinyl imidazole)‐based hydrogels

In this article, we report on the extraction of Sr(II) ions from aqueous solution with a series of poly(N‐vinyl imidazole)‐based hydrogels. The hydrogels were synthesized by the crosslinking of N‐vinyl imidazole with four different crosslinkers with γ rays as initiators. The well‐characterized hydrogels were used as Sr(II) sorbents. Sr(II) uptake was determined with a colorimetric method with Rose Bengal anionic dye. Scanning electron microscopy–energy‐dispersive spectroscopy analysis of the Sr(II)‐loaded polymers was recorded to ascertain the uptake of Sr(II) ions. The experimental adsorption values were analyzed with the Freundlich and Temkin equations, and the kinetics of adsorption were investigated with a pseudo‐second‐order sorption kinetic model. The results show that the equilibrium data fit well in the Freundlich isotherm and followed a pseudo‐second‐order kinetic model. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of PVA membrane modified by water‐soluble hyperbranched polyester (WHBP) for the dehydration of n‐butanol

Water‐soluble hyperbranched polyester (WHBP) was synthesized through the esterification reaction of the fourth generation hyperbranched polyester and maleic anhydride. A novel cross‐linked WHBP/PVA membrane was prepared by adding WHBP into poly(vinyl alcohol) (PVA) solution with glutaraldehyde as the cross‐linker. WHBP was characterized by Nuclear Magnetic Resonance and Attenuated Total Reflection Fourier Transform Infrared Spectroscopy (ATR‐FTIR), while WHBP/PVA membranes were characterized by ATR‐FTIR, X‐ray Diffraction, Scanning Electron Microscopy, Thermogravimetric Analysis, mechanical capacity, and water contact angle. Testing results showed that maleic anhydride was grafted on the surface of WHBP; compared with PVA membrane, WHBP/PVA membrane had lower crystallinity, weaker mechanical strength, higher hydrophilicity, and better thermal stability. Sorption and diffusion behaviors of n‐butanol and water in WHBP/PVA membrane were investigated; pervaporation performances of WHBP/PVA membrane were studied through the dehydration of the 90 wt % n‐butanol aqueous solution at 40°C. With an increase of the WHBP content from 0 to 30 wt %, both n‐butanol uptake and n‐butanol diffusion coefficient first decreased then increased; n‐butanol flux first decreased from 10 to 2 g·m^?2·h^?1 then increased to 213 g·m^?2·h^?1; both sorption selectivity and diffusion selectivity first increased then decreased; separation factor first increased from 88 to 1309 then decreased to 16. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43533.     

Enhanced toughness and strength of poly (d‐lactide) by stereocomplexation with 5‐arm poly (l‐lactide)

The enhancement of mechanical properties were achieved by solution blending of poly(d ‐lactide) (PDLA) and 5‐arm poly(l ‐lactide) (5‐arm PLLA). Differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) results indicated almost complete stereocomplex could be obtained when 5‐arm PLLA exceeded 30wt %. Tensile test results showed that the addition of 5‐arm PLLA in linear PDLA gave dramatically improvement both on tensile strength and elongation at break, which generally could not be increased simultaneously. Furthermore, this work transformed PDLA from brittle polymer into tough and flexible materials. The mechanism was proposed based on the TEM results: the stereocomplex crystallites formed during solvent evaporation on the blends were small enough (100–200 nm), which played the role of physical crosslinking points and increased the interaction strength between PDLA and 5‐arm PLLA molecules, giving the blends high tensile strength and elongation at break. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42857.     

Preparation of a poly(vinyl chloride) ultrafiltration membrane through the combination of thermally induced phase separation and non‐solvent‐induced phase separation

To regulate the polymer–diluent interaction and control the viscosity of the casting solution, diphenyl ketone (DPK) and a N,N‐dimethylacetamide/N,N‐dimethylformamide mixture were selected as a combined diluent. Poly(vinyl chloride) (PVC) utlrafiltration membranes, which had sufficient mechanical properties for their practical applications because of their bicontinuous spongy structure, were prepared by a combined process of thermally induced phase separation and non‐solvent‐induced phase separation. The phase‐separation mechanism was analyzed. In an air bath, the cast nascent solution immediately transformed into a transparent gel, and liquid–liquid phase separation was induced by a sudden drop in the temperature before crystallization. An ice–water bath was used to coagulate the membrane. The effects of the DPK and PVC concentrations on the membrane structures and performances were mainly investigated. The results show that an increase in the DPK content made the membrane pores change from fingerlike to spongy. Fully spongy pores formed, and the pores size decreased with increasing PVC concentration. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42953.     

Pervaporation of 50 wt % ethanol–water mixtures with poly(1‐trimethylsilyl‐1‐propyne) membranes at high temperatures

Poly(1‐trimethylsilyl‐1‐propyne) (PTMSP) membranes have been used to separate ethanol–water mixtures by pervaporation. This polyacetylene is known to present high affinity toward ethanol, showing high selectivity and ethanol permeation flux. The performance of this polymer in the separation of alcohol–water solutions has been evaluated over long periods (572 h) at a high temperature (75°C) to examine the deterioration of the transport properties in the separation of 50 wt % ethanol–water solutions. Although PTMSP membranes present good characteristics for the separation of gases and liquid mixtures, their organic selectivity decrease with the operating time because of the relaxation processes of the polymeric chains, which affect the free volume of the polymer, the deterioration being more evident for concentrated solutions. The effects of the operation temperature on the characteristic parameters of pervaporation have also been studied to establish how this variable affects the performance of PTMSP membranes. The selectivity increases slightly with the operation temperature, but the effect of the temperature on the separation factor decreases as membranes are degraded with the operation time. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2843–2848, 2007     

Crosslinking and stabilization of nanoparticle filled poly(1‐trimethylsilyl‐1‐propyne) nanocomposite membranes for gas separations

Poly(1‐trimethylsilyl‐1‐propyne) (PTMSP) has been crosslinked using 4,4′‐diazidobenzophenone bisazide to improve its chemical and physical stability over time. Crosslinking PTMSP renders it insoluble in good solvents for the uncrosslinked polymer. Gas permeability and fractional free volume decreased as crosslinker content increased, while gas sorption was unaffected by crosslinking. Therefore, the reduction in permeability upon crosslinking PTMSP was due to decrease in diffusion coefficient. Compared with the pure PTMSP membrane, the permeability of the crosslinked membrane is initially reduced for all gases tested due to the crosslinking. By adding nanoparticles (fumed silica, titanium dioxide), the permeability is again increased; permeability reductions due to crosslinking could be offset by adding nanoparticles to the membranes. Increased selectivity is documented for the gas pairs O₂/N₂, H₂/N₂, CO₂/N₂, CO₂/CH and H₂/CH₄ using crosslinking and addition of nanoparticles. Crosslinking is successful in maintaining the permeability and selectivity of PTMSP membranes and PTMSP/filler nanocomposites over time. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) in the presence of water

Poly(L ‐lactide‐co‐ε‐caprolactone) [P(LLA‐CL)], which is used in biodegradable biomedical materials such as drug‐delivery systems, surgical sutures, orthopedics, and scaffolds for tissue engineering, has been reported to crystallize upon storage in a dry state even at room temperature; this results in rapid changes in the mechanical properties. In biomedical applications, P(LLA‐CL) is used in the presence of water. This study investigated the effects of water on the crystallization of P(LLA‐CL) at 37°C in phosphate buffered solution, which was anticipated to alter its mechanical properties and hydrolytic degradation behavior. Surprisingly, the crystallinity of P(LLA‐CL) in the presence of water rapidly increased in 6–12 h and then slowly increased up to 120 h. The period of time for the initial rapid crystallization increase in the presence of water was much shorter than that in the absence of water. The obtained information would be useful for the selection, preparation, and use of P(LLA‐CL) in various biomedical applications. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of nano‐TiO2 on the properties and structures of starch/poly(ε‐caprolactone) composites

Poor physical properties resulting from low interfacial interactions between hydrophilic biopolymers and hydrophobic thermoplastic matrices have been one of the biggest obstacles in preparing quality biomass materials. This study concentrates on the effects of nano‐TiO₂ on the properties and structure of starch/poly (ε‐caprolactone) (PCL) composites. The molecular and crystal structures of the composites were characterized by using Fourier transform infrared spectroscopy, differential scanning calorimeter (DSC), X‐ray diffraction (XRD), and field emission scanning electron microscope. The results indicated that an interpenetrating network structure formed by adding nano‐TiO₂ into starch/PCL composites. The DSC and XRD analysis indicated that the crystallinity degree and the crystallization rate of the composites reduced, whereas the crystal form and crystal size were unchanged. The results also showed that the mechanical properties and water resistance of the composites were improved significantly with the addition of nano‐TiO₂, whereas their transparency decreased. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4129–4136, 2013     

Surface modification of ion‐exchange membranes: Methods,characteristics, and performance

Considerable effort has been made to improve ion‐exchange membrane (IEM) properties in order to achieve better performance of IEM‐based processes in various applications. Surface modification is one of the effective ways to improve IEM properties. Various methods have been used to modify IEM surfaces, for example, plasma treatment, polymerization, solution casting, electrodeposition, and ion implantation. These methods are able to produce a thin and fine distributed layer and also to modify the chemical structure of the surface. The new layer can be adsorbed, deposited, or chemically bonded on a membrane surface. By using these methods, IEM properties are improved, and the desired or specific characteristics such as high monovalent ion permselectivity, low fuel crossover, and anti‐organic‐fouling property can be obtained. In this paper, methods for surface modification of IEMs are reviewed. Moreover, the effects of modification on IEM properties and performance are discussed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45540.     

Crystallization behavior of poly(p‐dioxanone)‐PU/montmorillonite nanocomposites prepared by chain‐extending reaction

Organo‐modified montmorillonites and poly(p‐dioxanone) (PPDO) diol prepolymers were used to prepare Poly(p‐dioxanone)‐PU/organic montmorillonite (PPDO‐PU/OMMT) nanocomposites by chain‐extending reaction. The crystallization behavior and spherulitic morphology of PPDO‐PU/OMMT nanocomposites were investigated by WXRD, differential scanning calorimetry, and polarized optical microscopy. The results show that the regularity of the chain structure plays a dominant role during the crystallization process rather than that of OMMT content and its dispersion status in PPDO matrix. With similar molecular weight and same OMMT content, PPDO‐PU/OMMT nanocomposite, which derived from lower molecular weight PPDO prepolymer, exhibits lower crystallization rate, melting point, and crystallinity. The influence of the clay content on the crystallization behavior highly depends on its dispersing state. The nucleating effect of OMMT can be only observed at high loading percentage. For the nanocomposites with low clay loading percentage, the retarding effect of exfoliated platelets on the chain‐ordering into crystal lamellae became the key factor. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Enhanced thermoelectric performance of poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS) with long‐term humidity stability via sequential treatment with trifluoroacetic acid

This paper reports a range of effective sequential chemical processes to enhance the thermoelectric performance of conducting poly(3,4‐ethylenedioxythiophene) films doped with poly(styrene sulfonate) anions (PEDOT:PSS). The electrical conductivity of the PEDOT:PSS films was significantly increased from 0.33 to 3748 S cm^?1 after a series of sequential treatments with trifluoroacetic acid (TFA) while the Seebeck coefficient and thermal conductivity were slightly reduced from 17.5 ± 1.2 to 16.0 ± 1.1 μV K^?1 and 0.537 to 0.415 W m^–1 K^?1 for the pristine film and treated film, respectively, leading to a significant improvement in power factor up to 97.1 ± 5.4 μW m^–1 K^?2. More importantly, around 80% of the electrical conductivity and Seebeck coefficient was retained after 20 days for these TFA‐treated PEDOT:PSS films, revealing the potential for real thermoelectric applications. © 2019 Society of Chemical Industry