High-temperature performances of Si-HfO2-based environmental barrier coatings via atmospheric plasma spraying

To improve high-temperature bearing capability of coatings, novel agglomerated Si-HfO₂ powders were prepared by adding HfO₂ powders into original Si powders by spray drying method. Three-layer environmental barrier coatings (EBCs) with Si-HfO₂ bond layer, Yb₂Si₂O₇ intermediate layer and Yb₂SiO₅ surface layer were prepared on SiC ceramic substrates by atmospheric plasma spraying (APS). The high temperature properties of coatings were systematically investigated. The results indicated that the coatings had good high temperature oxidation resistance, and remained intact after being oxidized or steam corrosion at 1400 °C for 500 h, so the addition of HfO₂ improved the thermal cycling performances of the coating. The HfO₂ in Si bond coating could effectively inhibit the growth of thermal grown oxide at high temperatures. This work indicates that the high temperature properties of the coatings are improved by this novel EBCs using the novel agglomerated Si-HfO₂ powders.     

Oxidation behaviors and mechanisms of Yb2O3-doped silicon coatings fabricated by vacuum plasma spray

Environmental barrier coatings (EBCs) have been widely studied for the protection of ceramic matrix composites (CMCs). The phase transition of silica thermal growth oxide (TGO) has been proved to be an important factor for the durability of EBCs. Yb₂O₃ could react with SiO₂ TGO and form silicate which may improve the stability of TGO and prolong the service life of EBCs. In the present work, Si coatings doped with different contents of Yb₂O₃ were fabricated by vacuum plasma spray. The oxidation behaviors of the composite coatings were evaluated at 1350 °C and compared with the pure Si coating. The evolution of phase composition and microstructure of mixed thermal growth oxide (mTGO) was characterized in detail. The results showed that the newly formed oxidation product, namely Yb₂Si₂O₇, could reduce the vertical cracks in mTGO layer and the mTGO/coating interface cracks, leading to a better binding performance of the mTGO layer. The oxidation mechanisms of the Yb₂O₃-doped Si coatings were analyzed based on microstructure and phase composition observations.     

Environmental barrier coatings using low pressure plasma spray process

Yb₂Si₂O₇/Si bilayer environmental barrier coatings (EBCs) on SiC ceramic substrate were produced by low pressure plasma spray (LPPS) process. Phase composition, microstructure, and thermal durability of LPPS Yb₂Si₂O₇/Si coating were investigated. XRD analysis indicated that the coating is mainly composed of Yb₂Si₂O₇ with ~15.5v% Yb₂SiO₅ phases. The LPPS EBCs have a dense microstructure with porosity less than 4%. Adhesion strength measurement indicated the LPPS EBCs have an average adhesion strength of 29.1 ± 0.8 MPa. Furnace cycle test (FCT) on the coatings in air at 1316°C was performed and the test ran for 900 cycles and there was no coating spallation/failure for LPPS Yb₂Si₂O₇/Si EBCs. The FCT results demonstrated the excellent thermal cycle durability of LPPS EBCs. Oxidation kinetics investigation of LPPS EBCs in flowing 90% H₂O (g)+10% air at 1316°C showed that the thermally grown oxide (TGO) growth rate is close to the oxidation rate of pure Si in dry air and is significantly lower than that in water vapor environment. The LPPS process is promising in making highly durable Yb2Si2O7-based dense EBCs by impeding diffusion and ingression of water vapor/O₂.     

Cyclic oxidation performances of new environmental barrier coatings of HfO2-SiO2/Yb2Si2O7 coated SiC at 1375 °C and 1475 °C in the air environment

The objective of this work is to study the cyclic oxidation performances of the environmental barrier coatings (EBCs) containing the novel HfO₂-SiO₂ bond coats in the air environment. Bi-layer HfO₂-SiO₂/Yb₂Si₂O₇ (50HfO₂-50SiO₂, 70HfO₂-30SiO₂ bond coats) and conventional Si/Yb₂Si₂O₇ EBCs were deposited on SiC substrate using atmospheric plasma spray. The effect of the pre-mixing ratios of HfO₂/SiO₂ on the cyclic oxidation behavior of HfO₂-SiO₂/Yb₂Si₂O₇ EBCs was examined. The results showed that the higher content of the HfSiO₄ formed from the 50HfO₂-50SiO₂ bond coats, and it remained intact. A thermally grown oxide (TGO) SiO₂ layer was formed at the bond coat/SiC interface. The parabolic oxidation rate constant (k_p, μm²/h) of the TGO has been reduced 2 orders of magnitude in 50HfO₂-50SiO₂/Yb₂Si₂O₇ EBCs coated SiC compared to the bare SiC at 1475 °C, indicating that the 50HfO₂-50SiO₂/Yb₂Si₂O₇ EBCs effectively protected the SiC substrate at 1475 °C.     

Characterization of Yb2Si2O7–Yb2SiO5 composite environmental barrier coatings resultant from in situ plasma spray processing

Plasma spraying of multicomponent materials produces shifts in coating composition associated with differential vaporization of constituent elements within the strong thermal gradients of the process. This effect is quite noticeable in rare-earth silicates which are now widely being employed as Environmental Barrier Coatings (EBCs) for SiC based ceramic components of turbine engines. Of particular interest is the preferential volatilization of SiO₂ during thermal plasma spraying Yb₂Si₂O₇ (ytterbium disilicate) coatings which leads to the deviation from stoichiometry of the desired disilicate composition resulting in a mixed phase coating consisting of Yb₂Si₂O₇ plus Yb₂SiO₅ (ytterbium monosilicate). Recent work has shown that presence of monosilicate can be beneficial as its evolution from amorphous, metastable to stable crystalline phase can lead to crack healing during high temperature exposure, however, careful control of the chemistry and architecture may be needed. In this work a 50/50 mol% Yb₂Si₂O₇–Yb₂SiO₅ composite coating has been targeted through in situ decomposition during plasma spray from stoichiometric Yb₂Si₂O₇ powder. The as sprayed amorphous coating reverts to crystalline upon thermal treatment passing through a metastable state identified by XRD and Raman spectroscopy. The transition to the final stable phases results in a mixed phase coating comprising of 46/54 mol% Yb₂Si₂O₇–Yb₂SiO₅ composite that is thermo-mechanically stable with the underlying bond coated silicon coated SiC substrate.     

Autonomous crack healing ability of SiC dispersed Yb2Si2O7 by oxidations in air and water vapor

Yb₂Si₂O₇ is a popular environmental barrier coating; however, it decomposes into Yb₂SiO₅ in high-temperature steam environments. The thermal mismatch between Yb₂Si₂O₇ and Yb₂SiO₅ leads to the cracking and failure of the disilicate coating via oxidation. Dispersing SiC nanofillers into the Yb₂Si₂O₇ matrix is suggested to maintain the Yb₂Si₂O₇ matrix and promote crack self-healing. This study is aimed at clarifying the effect of water vapor on the self-healing ability of such composites. X-ray diffraction analysis and scanning electron microscopy were used to monitor the surface composition and the crack formation, respectively, in 10 vol% SiC-dispersed Yb₂Si₂O₇ composites. Annealing at temperatures higher than 750 °C in air or in a water vapor rich atmosphere led to strength recovery and the self-healing of indentation-induced surface cracks owing to volume expansion during the oxidation of SiC. The self-healing effect was influenced by the oxidation time and temperature. Rapid diffusion of H₂O as an oxidizer into the SiO₂ layer promoted self-healing in a water vapor rich atmosphere. However, accelerated oxidation at temperatures higher than 1150 °C formed bubbles on the surface. Fabricating composites with a small amount of Yb₂SiO₅ will be a solution to these problems.     

Exploration of the oxidation behavior and doping ratio of the Si–HfO2 bond layer used in environmental barrier coatings

Hafnia doping is expected to improve the performance of the silicon-bond layer of environmental barrier coatings (EBCs) for SiC-based ceramic matrix composites. The optimal doping ratio, distribution of HfO₂, and oxidation mechanism of the bond layer have not yet been fully addressed. A prototype Si–HfO₂ bond layer with a designed HfO₂-rich area was used to examine its oxidation behavior. A random dispersion model was developed to calculate the optimal HfO₂ doping ratio and its appropriate distribution state. The simulation results recommended that 20–30 vol% is the optimal doping ratio, where HfO₂ is well dispersed inside Si without forming networks. This enables HfO₂ to react with and consume SiO₂ without accelerating oxygen diffusion inside the bond layer. This was confirmed by oxidation experiments on Si–xHfO₂ tablets, in which the thinnest thermally grown oxide was achieved for the 20 vol% HfO₂-doped Si tablet. Both the microstructure design and material composition selection are highly important to further boost the performance of the EBCs.     

Crack-healing behaviour of MoSi2 dispersed Yb2Si2O7 environmental barrier coatings

MoSi₂ doped Yb₂Si₂O₇ composites were designed to extend the lifetime of Yb₂Si₂O₇ environmental barrier coatings (EBCs) via self-healing cracks during high-temperature applications. Yb₂Si₂O₇–Yb₂SiO₅–MoSi₂ composites with different mass fractions were prepared by applying spark plasma sintering. X-ray diffraction results confirmed that the composites consisted of Yb₂Si₂O₇, Yb₂SiO₅, and MoSi₂. The thermal expansion coefficients (CTEs) of the composites increased with an increase in the MoSi₂ content. The average CTE of the 15 wt% MoSi₂ doped Yb₂Si₂O₇ composite was 5.24 × 10^?6 K^?1, indicating that it still meets the CTE requirement of EBC materials. After being pre-cracked by using the Vickers indentation technique, the samples were annealed for 0.5 h at 1100 or 1300 °C to evaluate the crack-healing ability. Microstructural studies showed that cracks in 15 wt% MoSi₂ doped Yb₂Si₂O₇ composites were fully healed during annealing at 1300 °C. Two mechanisms may be responsible for crack healing. First, the cracks were filled with SiO₂ glass formed by MoSi₂ oxidation. Second, the formed SiO₂ continued to react with Yb₂SiO₅ to form Yb₂Si₂O₇, which can cause cracks to heal owing to volumetric expansion. The Yb₂Si₂O₇ formation with smaller volume expansion is more beneficial.     

Plasma spray deposition of tri-layer environmental barrier coatings

An air plasma spray process has been used to deposit tri-layer environmental barrier coatings consisting of a silicon bond coat, a mullite inter-diffusion barrier, and a Yb₂SiO₅ top coat on SiC substrates. Solidified droplets in as-deposited Yb₂SiO₅ and mullite layers were discovered to be depleted in silicon. This led to the formation of an Yb₂SiO₅ + Yb₂O₃ two-phase top coat and 2:1 mullite (2Al₂O₃*SiO₂) coat deposited from 3:2 mullite powder. The compositions were consistent with preferential silicon evaporation during transient plasma heating; a consequence of the high vapor pressure of silicon species at plasma temperatures. Annealing at 1300 °C resulted in internal bond coat oxidation of pore and splat surfaces, precipitation of Yb₂O₃ in the top coat, and transformation of 2:1 mullite to 3:2 mullite + Al₂O₃. Mud-cracks were found in the Yb₂SiO₅ layer and in precipitated Al₂O₃ due to the thermal expansion mismatch between these coating phases and the substrate.     

Thermal shock resistance of tri‐layer Yb2SiO5/Yb2Si2O7/Si coating for SiC and SiC‐matrix composites

A new tri‐layer Yb₂SiO₅/Yb₂Si₂O₇/Si coating was fabricated on SiC, C/SiC, and SiC/SiC substrates, respectively, using atmospheric plasma spray (APS) technique. All coated samples were subjected to thermal shock test at 1350°C. The evolution of phase composition and microstructure and thermo‐mechanical properties of those samples before and after thermal shock test were characterized. Results showed that adhesion between all the 3 layers and substrates appeared good. After thermal shock tests, through microcracks which penetrated the Yb₂SiO₅ top layer were mostly halted at the Yb₂SiO₅‐Yb₂Si₂O₇ interface and no thermal growth oxide (TGO) was formed after 40‐50 quenching cycles, implying the excellent crack propagation resistance of the environmental barrier coating (EBC) system. Transmission electron microscopy analysis confirmed that twinnings and dislocations were the main mechanisms of plastic deformation of the Yb₂Si₂O₇ coating, which might have positive effects on crack propagation resistance. The thermal shock behaviors were clarified based on thermal stresses combined with thermal expansion behaviors and elastic modulus analysis. This study provides a strategy for designing EBC systems with excellent crack propagation resistance.     

Thermophysical properties of Yb2O3 doped Gd2Zr2O7 and thermal cycling durability of (Gd0.9Yb0.1)2Zr2O7/YSZ thermal barrier coatings

(Gd_1−xYb_x)₂Zr₂O₇ compounds were synthesized by solid reaction. Yb₂O₃ doped Gd₂Zr₂O₇ exhibited lower thermal conductivities and higher thermal expansion coefficients (TECs) than Gd₂Zr₂O₇. The TECs of (Gd_1−xYb_x)₂Zr₂O₇ ceramics increased with increasing Yb₂O₃ contents. (Gd_0.9Yb_0.1)₂Zr₂O₇ (GYbZ) ceramic exhibited the lowest thermal conductivity among all the ceramics studied, within the range of 0.8–1.1 W/mK (20–1600 °C). The Young's modulus of GYbZ bulk is 265.6 ± 11 GPa. GYbZ/YSZ double-ceramic-layer thermal barrier coatings (TBCs) were prepared by electron beam physical vapor deposition (EB-PVD). The coatings had an average life of more than 3700 cycles during flame shock test with a coating surface temperature of ∼1350 °C. Spallation failure of the TBC occurred by delamination cracking within GYbZ layer, which was a result of high temperature gradient in the GYbZ layer and low fracture toughness of GYbZ material.     

Property evolutions of Si/mixed Yb2Si2O7 and Yb2SiO5 environmental barrier coatings completely wrapping up SiCf/SiC composites under 1300 °C water vapor corrosion

A bi-layer environmental barrier coating (EBC) consisting of silicon(Si) bond coat/mixed ytterbium disilicate (Yb₂Si₂O₇) and ytterbium monosilicate (Yb₂SiO₅) topcoats has been successfully prepared to completely wrap up the SiC_f/SiC composites and the protective effects of such EBC have been evaluated by soaking them in a mixed 50% O₂ and 50% H₂O corrosive gases at 1300 °C for various times. In topcoats, Yb₂Si₂O₇ is the major phase, providing good thermal expansion coefficient (CTE) matching with composite substrate and thus excellent thermal shock resistance, whereas Yb₂SiO₅ is the dispersing minor phase, providing improved water vapor corrosion resistance. The completely wrapping up of SiC_f/SiC composites by above EBC system is employed to avoid direct exposure to the corrosive conditions, making it possible to evaluate the genuine protection effects of current EBCs. Under 1300 °C water vapor corrosion, the mass change, the phase composition and the evolution of microstructure are investigated, which suggest that the bi-layer EBC has excellent performance on protecting SiC_f/SiC composites from water vapor corrosion at 1300 °C.     

SiC modified self-healing ytterbium disilicate materials for potential environmental barrier coating application

Environmental barrier coatings (EBCs) are crucial to the reliability and durability of SiC_f/SiC composite components seeking applications in hot sections of next-generation advanced aero-engines. The cracks initiated and developed in EBCs owing to various reasons during service greatly undermine their lifespans. To address this problem, in this work, silicon carbide (SiC) in the forms of particles and whiskers with various amounts have been introduced to ytterbium disilicate (Yb₂Si₂O₇), the mainstream EBC topcoat materials, so as to gain some self-healing potential. The results reveal that, the SiC inclusions in Yb₂Si₂O₇ in the presence of ytterbium monosilicate (Yb₂SiO₅) can trigger the following reactions. Specifically, SiC self-healing agents are oxidized to form viscous SiO₂, which actively reacts with Yb₂SiO₅ upon encountering it, forming Yb₂Si₂O₇. This has brought twofold beneficial effects including ① silicon supplementation of disilicate topcoat, whose silicon element tends to be “dragged out” by water vapor, leading to the deterioration of thermal mismatch; as well as ② crack self-healing resulting from the volume expansion induced by the above reactions. Then the two aspects of self-healing agents, namely the “promptness” and “sustainability,” have been discussed in detail. The former is unveiled to be more pertinent to the repairing of large cracks, whilst the latter is more relevant to the self-healing of tiny cracks at initiation or early stage of propagation. The current work sheds some lights on the design and development of more durable and robust EBCs with self-healing capability.     

Thermal cycle test performances of environmental barrier coatings of HfO2-SiO2/Yb2Si2O7 in the steam environment at 1475 °C

The novel bi-layer environmental barrier coatings (EBCs) with HfO₂-SiO₂/Yb₂Si₂O₇ structure (70HfO₂-30SiO₂/Yb₂Si₂O₇: 70HS/YbDS, 50HfO₂-50SiO₂/Yb₂Si₂O₇: 50HS/YbDS, molar ratios) was tested in 90%H₂O–10%O₂ conditions between room temperature and 1475 °C in an Al₂O₃ tube furnace, then its performance was evaluated. The YbDS layer was contaminated by alumina impurities under steam conditions. After 22 cycles, the 70HS/YbDS completely separated from the SiC substrate, while the 50HS/YbDS and SiC did not separate, even though cracks formed at the 50HS/SiC interface and the TGO layer. Furthermore, the thermally grown oxide (TGO) layer formed at the HfO₂-SiO₂/SiC interface. Formation and growth of the TGO led to the formation and propagation of cracks at the HfO₂-SiO₂/TGO interface and TGO interior, which was the culprit leading to the failure of EBCs. These results demonstrated that the 50HS/YbDS EBCs have the potential to protect SiC in steam conditions at 1475 °C.     

High-temperature interface stability of tri-layer thermal environmental barrier coatings

Thermal environmental barrier coatings (TEBCs) are capable of protecting ceramic matrix composites (CMCs) from hot gas and steam. In this paper, a tri-layer TEBC consisting of 16 mol% YO_1.5 stabilized HfO₂ (YSH16) as thermal barrier coating, ytterbium monosilicate (YbMS) as environmental barrier coating, and silicon as the bond coating was designed. Microstructure evolution, interface stability, and oxidation behavior of the tri-layer TEBC at 1300 °C were studied. The as-sprayed YSH16 coating was mainly comprised of cubic phase and ～3.4 vol% of monoclinic (M) phase. After 100 h of heat exposure, the volume fraction of the M phase increased to ～27%. The YSH16/YbMS interface was proved to be very stable because only slight diffusion of Yb to YSH16 was observed even after thermal exposure at 1300 °C for 100 h. At the YbMS/Si interface, a reaction zone including a Yb₂Si₂O₇ layer and a SiO₂ layer was generated. The SiO₂ grew at a rate of ～0.039 μm²/h in the first 10 h and a reduced rate of 0.014 μm²/h in the subsequent exposure.     

Constrained sintering and thermal ageing behaviour of electrophoretically deposited Yb2Si2O7 environmental barrier coating

The oxidation of SiC and the formation of a thermally grown oxide layer (TGO) limit the lifetime of environmental barrier coatings. Thus, this paper focuses on the deposition of denser Yb₂Si₂O₇ coatings using electrophoretic deposition to reduce the TGO growth rate. The findings showed densification for Yb₂Si₂O₇ can be achieved with an optimized sintering profile (heating/cooling rate, temperature, and time). However, the addition of 1.5 wt% of Al₂O₃ to Yb₂Si₂O₇ promoted densification and lowered the required sintering temperature, 1380 °C using 2 °C/min heating/cooling rate for 10 h provided efficient coating density. Moreover, adding Al₂O₃ reduced the TGO growth rate by more than 70 % compared to the Al₂O₃-free coatings, without cracking in TGO after 150 h of thermal ageing at 1350 °C. Results within this study suggest electrophoretic deposition with Al₂O₃ addition produces promising Yb₂Si₂O₇ environmental barrier coatings on SiC substrate with low oxidation rates and increased lifetime.     

Enhancing CMAS corrosion resistance of PS-PVD Si/Yb2Si2O7 EBCs via Al-modification

Enhancing the resistance to molten silicate corrosion is crucial for the long service life of environmental barrier coatings (EBCs). In this study, we used the Al-modification technique to enhance the CMAS corrosion resistance of Si/Yb₂Si₂O₇ coatings prepared by plasma spray-physical vapor deposition. The results show that the Al-modified Yb₂Si₂O₇ coating had higher resistance to CMAS corrosion than the Yb₂Si₂O₇ coating annealed at 1300 ℃ for 100 h, which is related to the refractory mullite and Yb₂Mg(AlO₂)₂O₃ generated during the CMAS exposure of Al-modified Yb₂Si₂O₇ coating. The Al-modified Yb₂Si₂O₇ coating also exhibited excellent resistance to oxygen penetration. The Al-modification technology provides the direction for the corrosion resistance of Yb₂Si₂O₇ system to CMAS.     

Mechanical properties and microstructure of Yb2SiO5 environmental barrier coatings under isothermal heat treatment

Yb₂SiO₅ (ytterbium monosilicate) top coatings and Si bond coat layer were deposited by air plasma spray method as a protection layer on SiC substrates for environmental barrier coatings (EBCs) application. The Yb₂SiO₅-coated specimens were subjected to isothermal heat treatment at 1400 °C on air for 0, 1, 10, and 50 h. The Yb₂SiO₅ phase of the top coat layer reacted with Si from the bonding layer and O₂ from atmosphere formed to the Yb₂Si₂O₇ phase upon heat treatment at 1400 °C. The oxygen penetrated into the cracks to form SiO₂ phase of thermally grown oxide (TGO) in the bond coat and the interface of specimens during heat treatment. Horizontal cracks were also observed, due to a mismatch of the coefficient of thermal expansion (CTE) between the top coat and bond coat. The isothermal heat treatment improves the hardness and elastic modulus of Yb₂SiO₅ coatings; however, these properties in the Si bond coat were a little bit decreased.     

Multilayer gradient rare earth disilicate coating prepared by in-situ melt infiltration and sintering method with high thermal shock resistance on porous Si3N4 ceramics

Dense multilayer gradient rare earth disilicate (γ-Y₂Si₂O₇ /β-Yb₂Si₂O₇ /β-Lu₂Si₂O₇) coatings were in-situ prepared by melt-infiltration /sintering procedure on porous Si₃N₄ ceramics for water resistance. Experimental and numerical simulation methods were used to study their thermal shock behavior. As a control, thermal shock behavior of pure γ-Y₂Si₂O₇ coatings were also compared. FEM results showed that the gradient design of modulus in ceramic coating can effectively avoid the mismatch of mechanical properties between coating layer and internal substrate, reducing the transient thermal stress in each layer during thermal shock. All of the pure γ-Y₂Si₂O₇ coatings were failed after thermal shock tests with ΔT ≈ 1200 ℃. However, when sintering temperature of multi-layer disilicate coatings were higher than 1400 ℃, the water absorption rates after thermal shock were all less than 5%, still showing good waterproof performance. The gradient design of modulus could effectively improve the structural stability of ceramic coatings.     

Effects of Gd2O3 and Yb2O3 on the microstructure and performances of O'-Sialon/Si3N4 ceramics for concentrated solar power

O'-Sialon/Si₃N₄ composite ceramics for solar absorber were prepared in situ through pressureless sintering from Si₃N₄ and low pure Al₂O₃ with different rare-earth oxides (i.e., Yb₂O₃ and Gd₂O₃). This study investigates the effects of Yb₂O₃ and Gd₂O₃ on phase composition, microstructure, densification, oxidation resistance and solar absorptance. The results revealed that Yb₂O₃ and Gd₂O₃, which were applied as flux materials, significantly reduced the sintering temperature and improved the densification, oxidation resistance of the composite ceramics. Moreover, the introduction of the two sintering aids promoted the formation of O'-Sialon through the liquid-phase sintering mechanism. The samples doped with Gd₂O₃ exhibited more O'-Sialon content, lower porosity, and better oxidation resistance compared with those doped with Yb₂O₃. Especially, sample A2 (6 wt% Gd₂O₃ additional) sintered at 1600 °C exhibited the best comprehensive properties for 10.10% water absorption, 23.29% porosity, 105.57 MPa bending strength, 75.16% solar absorption. Dense oxide layers were generated on sample surfaces after oxidation at 1300 °C, which protected the ceramics samples from further oxidation. However, the two additives had characteristic reflection peaks in the ultraviolet–visible region (300–400 nm) and were also blamed for high reflectivity in the near–infrared region, which resulted in the decrease in absorption.