Digital light processing additive manufacturing of in situ mullite-zirconia composites

Digital light processing (DLP) can produce small series ceramic parts with complex geometries and tiny structures without the high cost of molds usually associated with traditional ceramic processing. However, the availability of feedstock of different ceramics for the technique is still limited. Mullite-zirconia composites are refractory materials with diverse applications, nevertheless, their 3D printing has never been reported. In this work, alumina and zircon were used as raw materials for additive manufacturing by DLP followed by in situ mullite and zirconia formation. Thus, coarse zircon powder was milled to submicrometric size, alumina-zircon photosensitive slurries were prepared and characterized, parts were manufactured in a commercial DLP 3D printer, debound, and sintered at different temperatures. The printed parts sintered at 1600 °C completed the reaction sintering and reached a flexural strength of 84 ± 13 MPa. The process proved capable of producing detailed parts that would be unfeasible by other manufacturing methods.     

Additive manufacturing of Al2O3 ceramic core with applicable microstructure and mechanical properties via digital light processing of high solid loading slurry

Ceramic cores are essential intermediate mediums in casting superalloy hollow turbine blades. The developing of additive manufacturing (AM) technology provides a new approach for the preparation of ceramic cores with complex structure. In this study, alumina oxide (Al₂O₃) ceramic cores with fine complex geometric shapes were fabricated by digital light processing (DLP) in high resolution. The maximum solid content of 70 vol% of ceramic slurry was adopted in the printing process, which is important for the regulation of deformations and mechanical properties. The effects of the printing parameters, including exposure intensity, printing layer thickness and sintering temperature on the microstructures and mechanical properties of printed samples were investigated. The decrease of residual stress and similar shrinkage in X, Y, and Z directions could be obtained by adjusting the printing parameters, which are crucial to prepare complex ceramic cores with high quality. Besides, the flexure strength and open porosity of ceramic cores reached 34.84 MPa and 26.94%, respectively, which were supposed to meet the requirement of ceramic cores for the fabrication of superalloy blades.     

Additive Manufacturing of Dense Alumina Ceramics

In this study, a new process for additive manufacturing (AM) of dense and strong ceramic objects is described. The lithography‐based ceramic manufacturing (LCM) technique is based on the selective curing of a photosensitive slurry by a dynamic mask exposure process. The LCM technique is able to produce strong, dense and accurate alumina ceramics without virtually any geometrical limitations. With over 99.3% of a theoretical alumina density, four‐point bending strength of 427 MPa, and very smooth surfaces, the LCM process distinguishes itself from other AM techniques for ceramics and provides parts with very similar mechanical properties as conventionally formed alumina.     

Polymer-derived silicon nitride ceramics by digital light processing based additive manufacturing

In this work, silicon nitride ceramic components with simple cuboid and complex honeycomb and lattice structures from preceramic polymers were fabricated by using digital light processing (DLP) based additive manufacturing and pyrolysis. The photosensitive precursor for DLP based additive manufacturing was prepared by mixing high ceramic yield polysilazane with commercial acrylic resin and photoinitiator. The material formulation and the structure of the green body were characterized by using FTIR. Si₃N₄ ceramic cuboid, 2D-structured Si₃N₄ ceramic honeycomb, and 2D-structured Si₃N₄ ceramic lattice with high precision were fabricated. The DLP-prepared specimens were pyrolyzed at different temperatures, and the crystalline phases after pyrolysis were analyzed by using XRD. The optimal pyrolysis temperature was found to be 1400°C.microstructures were characterized by using SEM. The compressive behavior of the complex-shaped Si₃N₄ ceramic structures was measured and discussed in detail.     

Effect of organic fibers addition on digital light processing for Al2O3 porous ceramics

Porous ceramics based on additive manufacturing have great application potential in many industries, including filtration, catalysis, and heat insulation. In this research, we propose a method for manufacturing porous ceramics with connected channels structure through ceramic digital light processing (DLP) and organic fiber decomposition. The crossed fibers in the green body, working as a pore-forming agent, were decomposed and removed to form connected channels in ceramic. It was confirmed that ball milling changed the fiber morphology during slurry preparation, which was beneficial to promote fibers crossing. Besides, we focused on the influence of the “Sponge Compression effect” during the DLP process, which affected the fibers distribution. The existence of fibers in the green body resulted in uneven pressure distribution during the debinding process, providing a potential source of cracks. Results show that this method can produce channels with a diameter of 100 μm and high connectivity, providing great potential in fabricating high connectivity porous ceramics with complex shapes and structures.     

Complex mullite structures fabricated via digital light processing of a preceramic polysiloxane with active alumina fillers

By taking advantage of the multi-functional properties of preceramic polymers, their transformation into ceramic material at low sintering temperatures and the processing capabilities of polymer manufacturing processes, mullite components were fabricated by additive manufacturing. A photocurable silicone preceramic polymer resin containing alumina particles was shaped into complex structures via Digital Light Processing. Dense and crack-free, highly complex porous mullite ceramics were produced by firing a mixture of a commercially available photosensitive polysiloxane as the silica source, containing alumina powder as active filler, in air at a low sintering temperature (1300 °C). In particular, the developed formulations, coupled with the additive manufacturing approach, allow for precise control of the architecture of the porous ceramic components, providing better properties compared to parts with stochastic porosity.     

Stereolithography-based additive manufacturing of polymer-derived SiOC/SiC ceramic composites

In order to overcome challenges typically encountered during additive manufacturing of ceramics via the polymer precursor route, a novel polymer-derived SiOC/SiC composite system suitable for advanced geometric designs achievable by lithography-based ceramic manufacturing was established. The photoreactive resin system filled with 20 wt% SiC exhibits suitable viscosity characteristics, adequate stability against sedimentation, and a fast photocuring behavior. After printing and pyrolytic conversion, SiC particulates were well-dispersed within the polymer-derived SiOC matrix. A direct comparison with the unfilled polysiloxane-based resin system showed that the addition of particulate SiC increases handleability, reduces shrinkage, and significantly increases critical wall thicknesses up to 5 mm. The biaxial Ball-on-Three-Balls testing methodology yielded a characteristic strength of 325 MPa for SiOC/SiC composites. The results highlight the high potential of particle-filled preceramic polymer systems toward the fabrication of high-performance SiC-based materials by lithography-based additive manufacturing.     

Rapid and uniform in-situ solidification of alumina suspension via a non-contamination DCC-HVCI method using MgO sintering additive as coagulating agent

A novel rapid, uniform and non-contamination in-situ solidification method for alumina suspension by DCC-HVCI method using MgO sintering additive as coagulating agent was reported. MgO was used to release Mg²⁺ in suspensions via reaction with acetic acid generated from glycerol diacetate (GDA) at elevated temperature as well as to improve density and suppress grain growth of alumina ceramics during sintering. Influence of adding 0.7 wt% MgO with 2.0 vol% GDA in alumina suspension on coagulation process and properties of green bodies and sintered samples were investigated. It was indicated that the controlled coagulation of the suspension could be achieved after treating at 70 °C for 10 min. Homogeneous composition distribution of Mg element in EDS result indicated the uniform solidification of suspensions. Compressive strength of wet-coagulated bodies is 2.09±0.25 MPa. Dense alumina ceramics with relative density of 99.2% and flexural strength of 354±16 MPa sintered at 1650 °C for 4 h present homogeneous microstructure. The result indicated that the novel DCC-HVCI method via a sintering additive reaction with no contamination, short coagulation time and uniform in-situ solidification is a promising colloidal forming method for preparing high-performance ceramic components with complex shape.     

Influence of debinding holding time on mechanical properties of 3D-printed alumina ceramic cores

Herein, alumina green bodies are fabricated by three dimensional (3D) printing technology, then, the influence of debinding holding time under vacuum and argon on mechanical properties is systematically investigated by comparing the changes in microstructure, bulk density, open porosity, grain connection situation and flexural strength of ceramics. The flexural strength of alumina ceramics acquired the maximum values of 26.4 ± 0.7 MPa and 25.1 ± 0.5 MPa after debinding under vacuum and argon for 120 min and 180 min, respectively. However, the alumina ceramics rendered the flexural strength of 19.4 ± 0.6 MPa and 9.5 ± 0.4 MPa under vacuum and argon without extended holding time, respectively. The relatively low mechanical properties can be mainly attributed to the weak interlayer binding force, which is caused by layer-by-layer forming mode during 3D printing process and anisotropic shrinkage during the sintering process. Moreover, the alumina ceramics exhibited moderate bulk density and open porosity of 2.4 g/cm³ and 42% after the sintering process, respectively, which are mainly influenced by the microstructural evolution of alumina ceramics during thermal treatment. Also, the diffusion of gases is achieved by curing of photosensitive resin and influenced by different holding times during debinding, affecting the mechanical properties of sintered ceramics. The mechanical properties of as-sintered ceramics are suitable for the utilization of ceramic cores in the manufacturing of hollow blades.     

Three-dimensional printing of high-flux ceramic membranes with an asymmetric structure via digital light processing

In this study, a novel method was proposed for preparing high-flux ceramic membranes via digital light processing (DLP) three-dimensional (3D) printing technology. Two different alumina powders were well dispersed in a photosensitive resin to form a UV-curable slurry for DLP 3D printing. The effects of the grading ratio on the viscosity of the slurry and the porosity, pore size distribution, mechanical strength, roughness, and permeability of the ceramic membranes were systematically investigated. The thermal treatment conditions were also studied and optimized. The obtained ceramic membranes exhibited a uniform pore size distribution, a high porosity, a low tortuosity factor, and an asymmetric structure. The combination of these factors led to a high flux for the 3D-printed ceramic membranes. DLP 3D printing exhibited a good potential to be a strong candidate for the next generation of ceramic membrane fabrication technology.     

Laser stereolithography of ZrO2 toughened Al2O3

Ceramic laser stereolithography is a manufacturing process suitable candidate for the production of complex shape technical ceramics. The green ceramic is produced layer by layer through laser polymerisation of UV curable ceramic suspensions. A number of critical issues deserve attention: high solid loading and low viscosity of the suspensions, high UV reactivity, prevention of interlayer delamination in the green and in the sintered body, good mechanical performance. In this work, ZrO₂ reinforced Al₂O₃ components have been obtained from an acrylic modified zircon loaded with alumina powders. The zircon compound is effective as organic photoactivated resin and allows the dispersion of a high volume fraction of Al₂O₃ powder (up to 50 vol.%) while keeping viscosity at reasonable low values. The zircon compound also represents a liquid ceramic precursor that converts to oxide after burning out of the binder. Thanks to the good dispersion of the alumina powder in the zircon acrylate, a uniform dispersion of ZrO₂ submicron particles is obtained after pyrolysis. These are located at the grain boundaries between alumina grains. Formation of both monoclinic and tetragonal ZrO₂ occurs as evidenced by XRD. No delamination occurs in bending tests as evidenced by SEM fractography, satisfactory modulus and strength values were concurrently found.     

Flexural strength and Weibull analysis of Y-TZP fabricated by stereolithographic additive manufacturing and subtractive manufacturing

Digital light processing (DLP) is a relatively mature technology of ceramic additive manufacturing and is promising for fabricating zirconia-based dental restorations. It allows for manufacturing ceramic components with nearly unlimited geometries compared to traditional subtractive manufacturing technology. In order to explore its potential for fabricating dental prosthesis and determine its clinical indications, it is essential to investigate its microstructural characteristics and mechanical behavior. In this study, yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) fabricated by stereolithographic additive manufacturing, namely DLP acquired favorable flexural strength close to that of conventional subtractive-manufactured Y-TZP as indicated by uniaxial (three-point bending) and biaxial (ring on ring) tests, though the Weibull modulus of DLP-manufactured zirconia was lower than that of subtractive-manufactured zirconia. The strength predicting approach that uses effective area calculations was found to be applicable for both DLP-manufactured zirconia and subtractive-manufactured zirconia. Though both materials showed similar microstructures considering grain size and phase composition, significant differences in critical defects were observed.     

Study of alumina ceramic parts fabricated via DLP stereolithography using powders with different sizes and morphologies

Selecting suitable ceramic powders for the preparation of UV-curable ceramic suspensions, which are well suited for printing processes and production of high-performance ceramic components, is a crucial factor in the practical industrial application of digital light processing (DLP) stereolithography. Therefore, this study aims to provide a comprehensive evaluation of alumina ceramic parts fabricated via DLP stereolithography using a variety of alumina powders with varying sizes and morphologies. Experiments were conducted to examine the rheological response, recoating performance, and curing behavior of UV-curable alumina suspensions. Additionally, the thermal decomposition behavior of three-dimensional (3D)-printed green-bodies, as well as the physical and mechanical properties of 3D-printed sintered alumina components were thoroughly investigated. The best physical and mechanical performances were achieved by printing 55 vol% suspensions prepared using near-spherical AA04 alumina powders (median diameter .4 μm). This study elucidates the effects of ceramic particle size and morphology on the entire technological process of DLP-based ceramic stereolithography, thereby establishing the guidelines for the fabrication of high-performance 3D-printed ceramic objects in industrial and engineering production by selecting appropriate ceramic powders.     

Properties of multiple oxide-bonded porous SiC ceramics prepared by an infiltration technique

Multiple oxide-bonded porous SiC ceramics were fabricated by infiltrating a porous powder compact of SiC and alumina with cordierite sol followed by sintering at 1300-1400°C in air for 3 hours. The microstructures, phase components, mechanical properties, and air permeation behavior of the developed porous ceramics were examined and compared with materials obtained by the traditional powder processing route. The porosity, average pore diameter, and flexural strength of the ceramics varied from 33 to 37 vol%, ~12-14 μm and ~23-39.6 MPa, respectively, with variation in sintering temperature. The X-ray diffraction results reveal that both the amount of cordierite and mullite as the binder increased with increase in sintering temperature. In addition, it was found that the addition of alumina in powder form effectively enhanced the strength due to formation of mullite in the bond phase in contrast to the samples prepared without alumina additive. To determine the suitability of the material in particulate filtration application, particle collection efficiency of the filter material was evaluated theoretically using single collector efficiency model.     

Development and evaluation of Al2O3–ZrO2 composite processed by digital light 3D printing

Digital Light Processing (DLP) is a promising approach to fabricate delicate ceramic components with high-fidelity structural features. In this work, the alumina and zirconia/alumina ceramic suspensions with low viscosity and high solid loading (40 vol%) were prepared specifically for DLP 3D printing. After debinding and sintering, the final parts were obtained without any defects. The surface morphologies and mechanical properties of alumina (Al₂O₃) and zirconia toughened alumina (ZTA) composites were investigated and the results showed that the final parts exhibited high relative densities and good interlayer combination at the sintering temperature of 1600 °C. Comparing with the Al₂O₃, the ZTA composites exhibited significantly enhanced density (99.4%), bending strength (516.7 MPa) and indentation fracture toughness (7.76 MPa m^1/2).     

Fully sintered alumina with a higher Vickers hardness prepared using a gel-casting process

The dispersant (commercial ammonium polyacrylate), sintering additive (Mg²⁺), and chelating agent (EDTA) effects on the Zeta potential and rheological behavior of alumina slurry with high solid content were investigated. The alumina ceramic green microstructures and sintered microstructures prepared using slurries with different additives using the gel-casting process were also studied. It was observed that the dispersion deteriorated after adding Mg²⁺. Slurry simultaneously added with dispersant and EDTA-chelated Mg²⁺ produced higher absolute Zeta potential value and low viscosity due to EDTA chelating with Mg²⁺. The sample added with dispersant and EDTA-chelated Mg²⁺ exhibited a uniform green microstructure, high relative sintered density (99.5% theoretical density), and a nearly pore-free microstructure with an average grain size of about 1.5 μm. For the first time to our knowledge, the maximum Vickers hardness (22 GPa) was obtained for alumina simultaneously added with Mg²⁺ and EDTA, pressureless sintered at 1500°C in air.     

Investigating the effect of SPRM on mechanical strength and thermal conductivity of highly porous alumina ceramics

For recycling waste refractory materials in metallurgical industry, porous alumina ceramics were prepared via pore forming agent method from α-Al₂O₃ powder and slide plate renewable material. Effects of slide plate renewable material (SPRM) on densification, mechanical strength, thermal conductivity, phase composition and microstructure of the porous alumina ceramics were investigated. The results showed that SPRM effectively affected physical and thermal properties of the porous ceramics. With the increase of SPRM, apparent porosity of the ceramic materials firstly increased and then decreased, which brought an opposite change for the bulk density and thermal conductivity values, whereas the bending strength didn’t decrease obviously. The optimum sample A2 with 50 wt% SPRM introducing sintered at 1500 °C obtained the best properties. The water absorption, apparent porosity, bulk density, bending strength and thermal conductivity of the sample were 31.7%, 62.8%, 1.71 g/cm³, 47.1 ± 3.7 MPa and 1.73 W/m K, respectively. XRD analysis indicated that a small quantity of silicon carbide and graphite in SPRM have been oxidized to SiO₂ during the firing process, resulting in rising the porous microstructures. SEM micrographs illustrated that rod-like mullite grains combined with plate-like corundum grains to endow the samples with high bending strength. This study was intended to confirm the preparation of porous alumina ceramics with high porosity, good mechanical properties and low thermal conductivity by using SPRM as pore forming additive.     

Digital light processing-stereolithography three-dimensional printing of yttria-stabilized zirconia

Digital light processing (DLP)-stereolithography three-dimensional (3D) printing is a well known technique for fabricating components with complex geometries. However, the application of DLP 3D printing to functional ceramics such as 8 mol% yttria-stabilized zirconia (8YSZ), which is one of the most extensively used electrolyte materials for solid oxide fuel cells, is still a great challenge. Therefore, the fabrication of fully 8YSZ monoliths via DLP 3D printing was attempted herein, including the preparation of UV-curable ceramic suspensions, shaping of green bodies, and debinding and sintering. The results show that intact green bodies printed using a 30 vol% 8YSZ-photosensitive resin suspension with 0.1 wt% oleic acid as the dispersant under the optimized printing conditions was sufficiently dense without connected pores after vacuum debinding and sintering in air. The successful fabrication of 8YSZ monoliths with design flexibility via 3D printing provides a simple method for preparing functional ceramic components and may expand the application of 3D printing technology to the energy field.     

Application of SiO2-coated SiC powder in stereolithography and sintering densification of SiC ceramic composites

Stereolithography additive manufacturing of SiC ceramic composites has received much attention. However, the forming efficiency and mechanical properties of their products need to be improved. This study aimed to prepare SiC ceramic composites with complex shapes and high flexural strength using a combination of digital light processing (DLP) and reactive solution infiltration process (RMI). A low-absorbance SiO₂ cladding layer was formed on the surface of SiC powder through a non-homogeneous precipitation process. With the densification of the cladding layer at high temperatures, SiO₂-coated SiC composite powder was used to formulate a photosensitive ceramic slurry with a solid content of 44 vol%. The resulting slurry exhibited a considerable improvement in curing thickness and rate and was used to mold ceramic green body with a single-layer slicing thickness of 100 μm using DLP. The ceramic blanks were then sintered and densified using a carbon thermal reduction combined with liquid silica infiltration (LSI) process, resulting in SiC ceramic composites with a density of 2.87 g/cm³ and an average flexural strength of 267.52 ± 2.5 MPa. Therefore, the proposed approach can reduce the manufacturing cycle and cost of SiC ceramic composites.     

Extrusion-based additive manufacturing of functionally graded ceramics

The Ceramic On-Demand Extrusion (CODE) process has been recently proposed for additive manufacturing of dense, strong ceramic components via extrusion with uniform layered drying. This study focuses on enabling CODE to fabricate functionally graded ceramics. A controlled volumetric flowrate for each ceramic paste was used to achieve a gradient between alumina and zirconia. A dynamic mixer was built to mix constituent ceramic pastes homogeneously. Functionally graded alumina/zirconia samples were printed, sintered, and tested to examine the capability of CODE in fabricating functionally graded components. The desired and actual material compositions were compared using energy dispersive spectroscopy. Dimensions of sintered samples were evaluated to study the deformation of functionally graded components during drying and sintering. Vickers hardness was also measured at different locations, corresponding to different material compositions. Finally, a case study was conducted to demonstrate the capability of the proposed method to build functionally graded ceramics with complex geometries.