Spectroscopic properties of Nd<Superscript>3+</Superscript>, Yb<Superscript>3+</Superscript>-doped and Nd<Superscript>3+</Superscript>–Yb<Superscript>3+</Superscript>-codoped high silica glass

The Nd³⁺, Yb³⁺-doped and Nd³⁺–Yb³⁺-codoped high silica glasses (HSGs) were fabricated by sintering porous glasses impregnated with Nd³⁺ and Yb³⁺ ions solutions. The Judd–Ofelt theory was used to study the spectroscopic properties of Nd³⁺-doped HSGs. Large parameter Ω₂ of Nd³⁺-doped HSGs suggests a lower centrosymmetric coordination environment around the Nd³⁺ in HSG. The spontaneous emission probability and emission cross-section (σ_em) of Yb³⁺-doped HSGs are obtained. A broad emission band from 950 to 1,100 nm was detected when the Nd³⁺–Yb³⁺-codoped HSG was excited by 808 nm LD. The energy transfer process from Nd³⁺ to Yb³⁺ in HSG was described in this paper.     

The effect of temperature instability on the threshold sensitivity of photodetectors based on A<Superscript>III</Superscript>–B<Superscript>V</Superscript> photodiodes

The dependence of the sensitivity of photodetectors based on A^III–B^V photodiodes on accidental variations of the temperature of its elements is analyzed. It is shown that the temperature drift of the bias level in input circuits of op-amps strongly contributes to the resulting photodetector noise up to frequencies on the order of 1 MHz. To reach the limiting sensitivities of the sensors, it is necessary to stabilize the temperature of not only the photodiode chip, but also the integrated circuit of the first amplifier stage. For most of applications, the required stabilization accuracy does not exceed ±0.1°C. As a result of the analysis, prototype high-sensitivity medium-wavelength (2–5 μm) sensors were developed that operate without forced cooling and have a detection threshold of tens of nanowatts at a detection bandwidth of 0–1 MHz.     

Characterization of CBD–CdS nanocrystals doped with Co<Superscript>2+</Superscript>

Co-doped CdS nanofilms are synthesised by chemical bath deposition growth technique at the temperature of 60?±?2 °C. The cobalt molar fraction was ranged from 0 ≤ x ≤ 5.47, which was determined by energy-dispersive X-ray spectroscopy. The X-ray diffraction shows that the nanofilms are of CoS–CdS nanocomposites with individual CdS and CoS crystalline planes. The Co-doped CdS crystalline phase was zinc-blende that was determined by X-ray diffraction and confirmed by Raman spectroscopy. The average grain size of the CdS films was ranged from 2.56 to 1.67 nm that was determined by Debye–Scherrer equation from ZB (111) direction and it was confirmed by Wang equation and high resolution transmission electron microscopy (HRTEM). Raman scattering shows that the CdS lattice dynamics is characteristic of a bimodal behaviour, in which the first optical longitudinal mode denotes the characteristic peak at 305 cm^?1 of the CdS nanocrystals that is associated with the cobalt incorporation. Nanofilms present two main bandgaps at ~?2.56 and 3.80 eV, which are attributed to single CdS and quantum-confinement due to nanocrystals size. The increase in band gap with increase in cobalt concentration suggests intermetallic compound of CoS (E_g = 1.60 eV) with CdS (E_g = 2.44 eV). The CdS nanocrystals size was ranged from 2.46 to 1.81 nm that was determined from ZB (111) direction by Debye–Scherrer equation and confirmed by the Wang equation. The room-temperature photoluminescence of the Co-doped CdS presents well-resolved radiative bands associated to structural defects and with the quantum-confinement. For the Co-doped CdS the photoluminescence intensity increases indicate a high-passivation of the nanocrystals.     

Controllable white light emission from Dy<Superscript>3+</Superscript>–Eu<Superscript>3+</Superscript> co-doped KCaBO<Subscript>3</Subscript> phosphor

Potassium calcium borate, KCaBO₃:Eu³⁺ phosphors with various Dy³⁺ concentrations (0–3 wt%) were synthesized by solid state reaction and studied for the first time. Under various UV–violet excitations, the obtained single monoclinic phased Dy³⁺–Eu³⁺ co-doped KCaBO₃ polycrystalline phosphors emit a combination of yellow–blue and red–orange wavelength giving intense white light, which can easily be controlled by varying the concentration of Dy³⁺. The increase in white light emission with the increase of Dy³⁺ concentration indicates the efficient energy inter-ion transfer from Dy³⁺ to Eu³⁺ ions. Furthermore, the observed emission lifetimes and the intense white light emission are suggestive exploration for the present phosphor for potential optoelectronic applications such as white light-emitting phosphor for blue LEDs chips.     

Magnetic and Electrical Properties of Al<Superscript>3+</Superscript> Implanted Co–ZnO

Co-doped ZnO ceramic samples sintered at four different temperatures were prepared by solid-state reaction method and implanted by Al ions subsequently. The microstructural, defect, magnetic and electrical properties of the samples were systematically investigated by x-ray diffraction, micro-Raman spectroscope, vibrating sample magnetometer and Hall measurement, respectively. The results show that all the samples exhibit room-temperature ferromagnetism with a saturation magnetization of 0.02–0.03 emu g^?1, the value of which is affected by the sintering temperature. The origin of room-temperature ferromagnetism is considered as the formation of Co²⁺– V _O–Co²⁺ bound magnetic polarons. Even though the implantation of Al³⁺ slightly reduces the saturation magnetization because of the lattice damage, less V _O and larger lattice spacing, however, an appropriate amount of Al³⁺ implantation and a proper sintering temperature can remarkably improve the electrical properties with the mobility of 200 ～300 cm² Vs^?1 and the resistivity of 20 ～40 Ω cm. In general, samples sintered at 1200^°C present more excellent comprehensive performances.     

High-temperature tensile-hold crack-growth behavior of HASTELLOY<Superscript>®</Superscript> X alloy compared to HAYNES<Superscript>®</Superscript> 188 and HAYNES<Superscript>®</Superscript> 230<Superscript>®</Superscript> alloys

The creep–fatigue crack-growth tests of HASTELLOY^® X alloy were carried out at the temperatures of 649°C, 816°C, and 927°C in laboratory air. The experiments were conducted under a constant stress-intensity-factor-range (ΔK) control mode with a R-ratio of 0.05. In the constant ΔK tests, a ΔK of 27.5 MPa\(\sqrt{\mathrm{m}}\) and a triangular waveform with a frequency of 0.333 Hz were used. Various tensile hold times at the maximum load were imposed to study fatigue and creep–fatigue interactions. Crack lengths were measured by a direct current potential drop method. In this paper, effects of hold time and temperature on the crack-growth rates are discussed. Furthermore, the crack-growth rates of the HASTELLOY^® X alloy are compared to those of the HAYNES^® 188 and HAYNES^® 230^® superalloys.     

Crystal structure of compounds CsA<Superscript>V</Superscript>A′<Superscript>VI</Superscript>O<Subscript>6</Subscript> (A<Superscript>V</Superscript> = Sb,Ta; A′<Superscript>VI</Superscript> = W,U)

Compounds CsA^VA′^VIO₆ (A^V = Sb, Ta; A′^VI = W, U) were synthesized by high-temperature solidphase reactions. The crystal structures of the compounds were refined by the Rietveld method (space group Fd \(\bar 3\) m).     

Synthesis of Yb<Superscript>3+</Superscript>, Ho<Superscript>3+</Superscript> and Tm<Superscript>3+</Superscript> co-doped β-NaYF<Subscript>4</Subscript> nanoparticles by sol–gel method and the multi-color upconversion luminescence properties

Well-crystalline β-NaYF₄:Yb³⁺, Ho³⁺, Tm³⁺ nanoparticles were synthesized by sol–gel method using isopropyl alcohol [(CH₃)₂CHOH] as a complexing agent. The samples were characterized by X-ray diffraction, scanning electron microscopic analysis and fluorescence spectrum analysis methods. Under the excitation of 980 nm laser diode (LD), the samples displayed bright upconversion luminescence (UCL), which was generated from the energy level transition of Ho³⁺ and Tm³⁺ ions. With the increase of Tm³⁺, Ho³⁺ and Yb³⁺-doping concentration, the UCL intensity of blue, green and red light emission of the samples varied. Calculation of the CIE color coordinate of the β-NaYF₄:Yb³⁺, Ho³⁺, Tm³⁺ nanoparticles revealed that with the adjustment of Tm³⁺, Ho³⁺ and Yb³⁺ doping concentration and the excitation power of 980 nm LD, the multi-color UCL can be realized. Approximately single red light output with the CIE color coordinate of x?=?0.545, y?=?0.306 and white light output with the CIE color coordinate of x?=?0.325, y?=?0.320 can be obtained in the synthesized β-NaYF₄: Yb³⁺, Ho³⁺, Tm³⁺ nanoparticles.     

Comparison of an experimental bone cement with surgical Simplex<Superscript>®</Superscript> P,Spineplex<Superscript>®</Superscript> and Cortoss<Superscript>®</Superscript>

Conventional polymethylmethacrylate (PMMA) cements and more recently Bisphenol-a-glycidyl dimethacrylate (BIS-GMA) composite cements are employed in procedures such as vertebroplasty. Unfortunately, such materials have inherent drawbacks including, a high curing exotherm, the incorporation of toxic components in their formulations, and critically, exhibit a modulus mismatch between cement and bone. The literature suggests that aluminium free, zinc based glass polyalkenoate cements (Zn-GPC) may be suitable alternative materials for consideration in such applications as vertebroplasty. This paper, examines one formulation of Zn-GPC and compares its strengths, modulus, and biocompatibility with three commercially available bone cements, Spineplex, Simplex P and Cortoss. The setting times indicate that the current formulation of Zn-GPC sets in a time unsuitable for clinical deployment. However during setting, the peak exotherm was recorded to be 33 degrees C, the lowest of all cements examined, and well below the threshold level for tissue necrosis to occur. The data obtained from mechanical testing shows the Zn-GPC has strengths of 63 MPa in compression and 30 MPa in biaxial flexure. Importantly these strengths remain stable with maturation; similar long term stability was exhibited by both Spineplex and Simplex P. Conversely, the strengths of Cortoss were observed to rapidly diminish with time, a cause for clinical concern. In addition to strengths, the modulus of each material was determined. Only the Zn-GPC exhibited a modulus similar to vertebral trabecular bone, with all commercial materials exhibiting excessively high moduli. Such data indicates that the use of Zn-GPC may reduce adjacent fractures. The final investigation used the well established simulated body fluid (SBF) method to examine the ability of each material to bond with bone. The results indicate that the Zn-GPC is capable of producing a bone like apatite layer at its surface within 24 h which increased in coverage and density up to 7 days. Conversely, Spineplex, and Simplex P exhibit no apatite layer formation, while Cortoss exhibits only minimal formation of an apatite layer after 7 days incubation in SBF. This paper shows that Zn-GPC, with optimised setting times, are suitable candidate materials for further development as bone cements.     

The role of Sr<Superscript>2+</Superscript> on the structure and reactivity of SrO–CaO–ZnO–SiO<Subscript>2</Subscript> ionomer glasses

The suitability of Glass Polyalkenoate Cements (GPCs) for use in orthopaedics is retarded by the presence in the glass phase of aluminium, a neurotoxin. Unfortunately, the aluminium ion plays an integral role in the setting process of GPCs and its absence is likely to hinder cement formation. However, the authors have previously shown that aluminium free GPCs may be formulated based on calcium zinc silicate glasses and these novel materials exhibit significant potential as hard tissue biomaterials. To further improve their potential, and given that Strontium (Sr) based drugs have had success in the treatment of osteoporosis, the authors have substituted Calcium (Ca) with Sr in the glass phase of a series of aluminium free GPCs. However to date little data exists on the effect SrO has on the structure and reactivity of SrO–CaO–ZnO–SiO₂ glasses. The objective of this work was to characterise the effect of the Ca/Sr substitution on the structure of such glasses, and evaluate the subsequent reactivity of these glasses with an aqueous solution of Polyacrylic acid (PAA). To this end ²⁹Si MAS-NMR, differential scanning calorimetry (DSC), X-ray diffraction, and network connectivity calculations, were used to characterize the structure of four strontium calcium zinc silicate glasses. Following glass characterization, GPCs were produced from each glass using a 40 wt% solution of PAA (powder:liquid = 2:1.5). The working times and setting times of the GPCs were recorded as per International standard ISO9917. The results acquired as part of this research indicate that the substitution of Ca for Sr in the glasses examined did not appear to significantly affect the structure of the glasses investigated. However it was noted that increasing the amount of Ca substituted for Sr did result in a concomitant increase in setting times, a feature that may be attributable to the higher basicity of SrO over CaO.     

Structural and dielectric properties of nanocrystalline Nd<Superscript>3+</Superscript> substituted nickel–zinc ferrites

Ferrite samples with general formula Ni_1−xZn_xNd_yFe_2−yO₄ (x = 0, 0.2, 0.4, 0.6, 0.8 and 1; y = 0.01, 0.02 and 0.03) were synthesized by oxalate co-precipitation technique. The X-ray diffraction study confirms the formation of single-phase cubic spinel structure. The lattice constant of the samples increases with increase in zinc content and obeys Vegard’s law. On Nd³⁺ substitution lattice constant of the samples slightly increases except zinc ferrite. The frequency dependence of the dielectric constant, dielectric loss and AC conductivity of the samples were determined in the frequency range from 20 Hz to 1 MHz at room temperature. The experimental results reveal that the dielectric constant and dielectric loss decreases where as AC electrical conductivity increases with increase in frequency. The dielectric loss increases with increase in zinc content whereas it decreases with increase in Nd³⁺ content. There is no appreciable change in permittivity of the samples with increase in Nd³⁺ content. Permeability of all the samples increases with increase in Nd³⁺ content. Because of lower dielectric loss, Nd³⁺ substituted Ni–Zn ferrites are useful in electronic devices.     

<Superscript>172</Superscript>Hf → <Superscript>172</Superscript>Lu Radionuclide Generator Based on a Reverse-Tandem Separation Scheme

The distribution coefficients of Hf(IV) and Lu(III) between Dowex 50W×8 cation exchanger or Dowex 1×8 anion exchanger and mixed HCl–H₂C₂O₄ solutions and between Dowex 50W×8 cation exchanger or Dowex 1×8 anion exchanger and citric acid solutions were determined. A number of modifications of the ¹⁷²Hf → ¹⁷²Lu generator, based on reverse separation schemes, were examined. Systems consisting of an anion-exchange resin and a solution of appropriate organic acid were taken as a chemical basis of the generator. Irreversible sorption of ¹⁷²Lu in generator columns was studied. The optimum operation mode of the ¹⁷²Hf → ¹⁷²Lu generator based on the reverse-tandem scheme with periodic transfer of the parent radionuclide into the liquid phase was determined.     

Photoluminescence of Eu<Superscript>3+</Superscript> ion in SnO<Subscript>2</Subscript> obtained by sol–gel

Photoluminescence data of Eu-doped SnO₂ xerogels are presented, yielding information on the symmetry of Eu³⁺ luminescent centers, which can be related to their location in the matrix: at lattice sites, substituting to Sn⁴⁺, or segregated at particles surface. Influence of doping concentration and/or particle size on the photoluminescence spectra obtained by energy transfer from the matrix to Eu³⁺ sites is investigated. Results show that a better efficiency in the energy transfer processes is obtained for high symmetry Eu³⁺ sites and low doping levels. Emission intensity from ⁵D₀→⁷F₁ transition increases as the temperature is raised from 10 to 240 K, under excitation at 266 nm laser line, because in this transition the multiphonon emission becomes significant only above 240 K. As an extension of this result, we predict high effectiveness for room temperature operation of Eu-based optical communication devices. X-ray diffraction data show that the impurity excess inhibits particle growth, which may influence the asymmetry ratio of luminescence spectra.     

Simple methods to fabricate Bioglass<Superscript>®</Superscript>-derived glass–ceramic scaffolds exhibiting porosity gradient

The present paper discusses different processing technologies for fabrication of novel 45S5 Bioglass^®-derived glass–ceramic scaffolds with tailored porosity gradient for potential application in bone tissue engineering. Different types of scaffolds with continuous or stepwise gradient of porosity were produced by the foam replication technique, using preformed polyurethane (PU) foams as sacrificial templates. After preforming the PU foams in metallic moulds, they were dipped in a 45S5 Bioglass^®-based slurry and subsequently heat treated in a chamber furnace up to 1100 °C. During heating, the organic phase is burned out and the glass sinters and partially crystallises. By using this new approach, Bioglass^®-derived glass-ceramic scaffolds with different shapes and porosity profiles were designed. Scanning electron microscopy (SEM) showed that all samples have highly interconnected porous structure, with specific porosity gradients. By modifying the shape and dimensions of the metallic mould, bioactive glass–ceramic scaffolds with complex shapes and different degrees of porosity gradient could be obtained.     

Use of a nanostructured material for separation of <Superscript>238</Superscript>U and <Superscript>237</Superscript>U produced by the photonuclear reaction <Superscript>238</Superscript>U(γ, <Emphasis Type="Italic">n</Emphasis>)<Superscript>237</Superscript>U

²³⁷U was produced by the reaction ²³⁸U(γ, n) on an electron accelerator, MT-25 microtron, at the Flerov Laboratory of Nuclear Reactions. For the separation of ²³⁷U and [²³⁸U, the recoil nuclei were collected by a nanostructured material, hydrated manganese dioxide (of the cryptomelane type), in the solid-solid system. From fission products, ²³⁷U was separated by ion exchange. The specific activity of the resulting ²³⁷U was 4.5 × 10⁹ Bq (mg ²³⁸U)^-1, with the content of radioactive impurities of ≤10^-6 Bq Bq^-1. The chemical yield of ²³⁷U was 80%.     

Mechanism of grain growth and excellent polarization,dielectric relaxtion of La<Superscript>3+</Superscript>, Nd<Superscript>3+</Superscript> modified PZT nano-films prepared by sol–gel technique

Ferroelectric PbZr_0.52Ti_0.48O₃ film and its partial substitutions by rare earth ions La³⁺ and Nd³⁺ Pb_0.9(La/Nd)_0.1Zr_0.52Ti_0.48O₃, grown on Pt(111)/Ti/SiO₂/Si(100) substrates, were prepared via sol–gel and rapid thermal processes. Structural characterization by X-ray diffraction and scanning electron microscopy showed that Pb(Zr_0.52Ti_0.48)O₃ and Pb_0.9La_0.1(Zr_0.52Ti_0.48)O₃ films are of (111) preferred orientation but Pb_0.9Nd_0.1(Zr_0.52Ti_0.48)O₃ is more inclined to (100) reflection though both are of tetragonal perovskite structure. The results indicate that the piezoelectric properties of PZT thin films can be improved by doping La³⁺ and Nd³⁺ substituted A-site. The d₃₃ can be dramatically improved by doping La³⁺. Moreover, Pr of Pb(Zr_0.52Ti_0.48)O₃ films reaches up to 120.53 µC/cm², while the doping samples present relatively inferior ferroelectric hysteresis loops (Pr_La?=?64.32, Pr_Nd?=?53.17 µC/cm²), greater dielectric constants, higher dielectric loss and lower leakage current than the undoped Pb(Zr_0.52Ti_0.48)O₃ sample. And meanwhile, the samples showed a typical non-Debye dielectric spectroscopy of multiple quantum relaxation time distribution observing from the Cole–Cole plot at room temperature.     

Effect of the high doze of N<Superscript>+</Superscript>(10<Superscript>18</Superscript> cm<Superscript>–2</Superscript>) ions implantation into the (TiHfZrVNbTa)N nanostructured coating on its microstructure,elemental and phase compositions,and physico-mechanical properties

Structure and properties of (TiHfZrVNbTa)N nanostructured multicomponent coatings implanted with a very high (10¹⁸ cm^–2) dose of N⁺ions have been studied. As a result of the implantation a multilayer structure has been formed in the surface layer of the coating. The structure is composed of amorphous, nanocrystalline (disperse) and nanostructured (with the initial sizes) nanolayers. In the depth of the coating two phases (with the fcc and hcp structures) having a small volume content are formed. The nitrogen concentration near the surface attains 90 at % and then decreases with the depth. In the initial state after the deposition the coating nanohardness values are from 27 to 34 GPa depending on the conditions of the deposition. As a result of the implantation the hardness is decreased approximately by the depth of the projective ions range, i.e., to 12 GPa and then increases with the depth to 23 GPa. The investigations were conducted using the Rutherford backscattering, scanning electron microscopy with the microanalysis, high resolution electron microscopy (with local microanalysis), X-ray diffraction, nanoindentation, and wear tests.     

Effect of CdS nanoparticles on photoluminescence spectra of Tb<Superscript>3 + </Superscript> in sol–gel-derived silica glasses

CdS nanoparticles doped with Tb^3 + were synthesized by sol–gel technique. The influence of CdS on the Tb^3 + glass was studied by UV-Visible and luminescence spectroscopy. The luminescence intensity of the glasses increased significantly in the presence of CdS nanoparticles. Terbium ions excited into the ⁵ D ₃ level have a rich emission spectrum in the 400–700 nm range decaying to different ⁷ F _J levels. The intensity of violet and blue luminescence from ⁵ D ₃ level is highly dependent on Tb^3 + concentration, on presence of CdS co-dopant and annealing conditions.