Synthesis and characterization of highly stable optically passive CeO2-ZrO2 counter electrode

Transparent and adherent CeO₂-ZrO₂ thin films having film thicknesses ∼543-598 nm were spray deposited onto the conducting (fluorine doped tin oxide coated glass) substrates from a blend of equimolar concentrations of cerium nitrate hexahydrate and zirconium nitrate having different volumetric proportions (0-6 vol.% of Zr) in methanol. CeO₂-ZrO₂ films were polycrystalline with cubic fluorite crystal structure and the crystallinity was improved with increasing ZrO₂ content. Films were highly transparent (T ∼ 92%), showing decrease in band gap energy from 3.45 eV for pristine CeO₂ to 3.08-3.14 eV for CeO₂-ZrO₂ films. The different morphological features of the film obtained at various CeO₂-ZrO₂ compositions had pronounced effect on the ion storage capacity and electrochemical stability. CeO₂-ZrO₂ film prepared at 5 vol.% Zr concentration exhibited higher ion storage capacity of 24 mC cm⁻² and electrochemical stability of 10,000 cycles in 0.5 M LiClO₄ + PC electrolyte due to its film thickness (584 nm) coupled with relatively larger porosity (8%). The optically passive behavior of such CeO₂-ZrO₂ film (with 5 vol.% Zr) is affirmed by its negligible transmission modulation irrespective of repeated Li⁺ and electron insertion/extraction. The coloration efficiency of spray deposited WO₃ thin film is found to enhance from 47 to 107 cm² C⁻¹ when CeO₂-ZrO₂ is coupled as a counter electrode with WO₃ in an electrochromic device (ECD). These films can be used as stable ‘passive’ counter electrodes in electrochromic smart windows as they retain full transparency in both the oxidized and reduced states and ever-reported longevity.     

Growth and optical properties of cerium dioxide nanocrystallites prepared by coprecipitation routes

Nanosized cerium dioxide (CeO₂) powders have been synthesized using coprecipitation methods and cerium nitrate hexahydrate (Ce(NO₃)₃·6H₂O) as the starting material. The growth and optical properties of nanosized CeO₂ powders were investigated using X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), nano-beam electron diffraction (NBED), high resolution TEM (HRTEM), and ultraviolet–visible (UV–vis) absorption spectrophotometry. The XRD result shows that the dried CeO₂ precursor powders (both before and after calcination at various temperatures and times) contained a single crystalline phase of CeO₂. In the dried precursor powders, the crystallites of CeO₂ measured 10.4 nm and 66.8 nm before and after calcination at 1273 K for 240 min, respectively. The indirect band gap energy (_Ei$E_i$) of CeO₂ decreased from 3.03 eV to 2.68 eV as the crystallite size increased from 10.4 nm to 66.8 nm, whereas the direct band gap energy (_Ed$E_d$) of CeO₂ also decreased from 3.79 eV to 3.38 eV.     

Isothermal crystallization kinetics and effect of crystallinity on the optical properties of nanosized CeO2 powder

The isothermal crystallization kinetics and effect of crystallinity on the optical properties of cerium dioxide (CeO₂) nanopowders synthesized using a coprecipitation route at 293 K and pH 9 were investigated using X-ray diffraction, transmission electron microscopy, selected area electron diffraction, and ultraviolet–visible absorption spectrophotometry. The activation energy of CeO₂ crystallization from dried cerium dioxide precursor powders by isothermal method of 64.1±3.24 kJ/mol was obtained. The average value of the growth morphology parameter (n) is 1.94, meaning that two-dimensional growth with plate-like morphology was the primary mechanism of CeO₂ crystallization from cerium dioxide precursor powders. The indirect band gap energy (E_i) of CeO₂ decreased from 3.03 eV to 2.83 eV when the crystallinity increased from 18% to 82%, and the direct band gap energy (E_d) of CeO₂ also decreased from 3.76 eV to 3.64 eV.     

Effect of precursor characteristics on zirconia and ceria particle morphology in spray pyrolysis

Ultrasonic spray pyrolysis of acetate-based precursors with precisely measured precursor drop size was employed to produce ZrO₂ and CeO₂ particles. A bimodal size distribution of the product particles indicates a significant influence of the gas-to-particle conversion mechanism in addition to the conventionally accepted one-particle-per-drop mechanism. Due to the differences in solubility of the precursors, ZrO₂ particles are spherical in shape and smooth on their surfaces while the CeO₂ particles are bowl-like in shape with uneven surfaces. Spherical and monodispersed particles with a peak diameter <100 nm can be obtained by reducing the precursor concentrations to 0.01 wt.% in both the different precursor system.     

Directionally solidified CeO2 (or GDC)/CoO eutectic ceramics as cermet precursors for SOFCs anodes: Microstructure cross-over

Rods of CeO₂ and gadolinium-doped CeO₂ (GDC)-CoO eutectics were prepared by directional solidification using a laser heated floating zone (LFZ) technique. The microstructure has been studied as a function of the growth rate from V = 10 to 750 mm/h. Regular eutectic microstructures are obtained except for the highest growth rate. The interspacing follows the λ²V = C law with C = 4.1(3) × 10⁻¹⁷ and 2.6(3) × 10⁻¹⁷ m³/s for CeO₂-CoO and GDC-CoO eutectics, respectively. A cross-over between fibrous and lamellar eutectic microstructures was observed depending on the growth rate. The crystallography of the eutectics was studied by Electron Backscatter Diffraction (EBSD). The growth directions [1 1 0]_GDC ∼ //[110]_CoO, and the interfacial planes (200)_GDC//(111)_CoO, were identified. Solubility of Co in the ceria matrix was determined by Energy Dispersive X-ray (EDX) Spectroscopy after Co was leached out from the matrix. Co solubility in ceria at 1650 °C was found to be less than 1 mol%.     

Preparation and characterization of CeO2/TiO2 nanoparticles by flame spray pyrolysis

Nanocrystalline TiO₂, CeO₂ and CeO₂-doped TiO₂ have been successfully prepared by one-step flame spray pyrolysis (FSP). Resulting powders were characterized with X-ray diffraction (XRD), N₂-physisorption, Transmission Electron Microscopy (TEM) and UV-Vis spectrophotometry. The TiO₂ and CeO₂-doped TiO₂ nanopowders were composed of single-crystalline spherical particles with as-prepared primary particle size of 10-13 nm for Ce doping concentrations of 5-50 at%, while square-shape particles with average size around 9 nm were only observed from flame-made CeO₂. The adsorption edge of resulting powder was shifted from 388 to 467 nm as the Ce content increased from 0 to 30 at% and there was an optimal Ce content in association with the maximum absorbance. This effect is due to the insertion of Ce^3+/4+ in the TiO₂ matrix, which generated an n-type impurity band.     

Chemical reduction of nanocrystalline CeO2

The reduction of commercial and mechanochemically processed CeO₂ powders was studied. Nanostructured CeO₂, with the crystallite size of 21 nm and the lattice distortion of 0.37%, was obtained during 60 min of milling in a high-energetic vibratory mill. X-ray diffraction, scanning electron microscopy and Brunauer-Emmett-Teller method were applied to characterize the milled powders. During the thermal treatment at 1200 and 1400 °C in an argon atmosphere the nonstoichiometric CeO_2−x oxides with the defect fluorite structure were formed. Compositions of CeO_2−x oxides were determined according to its lattice parameter. The results showed that the release of oxygen, as well as the rate of reduction, was more effective in nanocrystalline then in the microcrystalline CeO₂, producing at 1200 °C CeO_1.80 and CeO_1.85 oxides, while at 1400 °C were obtained similarly, CeO_1.77 and CeO_1.78, compositions.     

Oriented polycrystalline mesoporous CeO2 with enhanced pore integrity

Mesoporous CeO₂ particles are synthesized using a sol–gel method involving Pluronic P123 or F127 tri-block copolymer and cerium acetate hydrate. Transmission electron microscopy reveals well defined meso-channels of about 10 nm in diameter and a wall framework consisting of highly oriented polycrystalline CeO₂. The [0 0 1] axis of the crystals is found to be aligned parallel to the meso-channels, and lattice coherency of [1 0 0] or [0 1 0] also exists in perpendicular plane to the channel. A cooperative self-assembly of the tri-block copolymer and Ce⁴⁺ species is believed to occur, along with the precipitation of nano-crystalline CeO₂ in the sol–gel process. It is proposed that the preferential orientation may result from a favored linkage of the low-order Miller indices {0 0 1} planes of CeO₂ to the PEO segment in the PEO–PPO–PEO tri-block copolymer micelles. The unique structural characteristics of meso-CeO₂ appear to contribute to maintaining the pore integrity during the synthesis as well as in a post-fabrication in situ TEM heating test.     

Synthesis of CeO2-ZrO2 solid solution by glycothermal method and its oxygen release capacity

The glycothermal (GT) reaction of Ce acetate and Zr alkoxide directly yielded CeO₂-ZrO₂ solid solutions in a region of low Ce content ≤40 mol%. Of the CeO₂-ZrO₂ solid solutions obtained by the GT method and subsequent calcination at 500 or 800 °C, the sample with 20 mol% Ce content had the largest BET surface area. This sample exhibited the highest Ce-based oxygen release capacity in the whole Ce/Zr composition range. The oxygen release capacities of CeO₂-ZrO₂ solid solutions synthesized by the GT method were much larger than those of the samples prepared by a coprecipitation (CP) method. The Reitveld analysis and the repetitive reduction-oxidation experiment indicated that the CeO₂-ZrO₂ solid solution synthesized by the GT method has a homogeneous structure as compared with that prepared by the CP method.     

Synthesis of nanocrystalline ytterbium-doped yttria by citrate-gel combustion method and fabrication of ceramic materials

Nanosized ytterbium doped yttria powders were prepared by citrate-gel combustion techniques. As-synthesized precursor and calcined powders were characterized for their crystalline structure, particle size and morphologies. Nanocrystalline Yb³⁺:Y₂O₃ powders with pure cubic yttria crystal structure were obtained by calcination of as-prepared precursors at 1100 °C for 3 h. Powders obtained were well dispersed with an average particle size of 60 nm. By using the obtained powders, nearly full dense Yb³⁺:Y₂O₃ ceramics were produced by vacuum sintering at 1800 °C for 12 h. The emission spectrum of the sintered ceramics under the excitation wavelength of 905 nm illustrates that there are three fluorescence peaks locating at 976 nm, 1030 nm and 1075 nm respectively, all corresponding to the ²F_5/2 → ²F_7/2 transitions of ytterbium ion.     

Hierarchical structured TiO2 nano-tubes for formaldehyde sensing

Hierarchical structured TiO₂ nano-tubes were prepared following a two-step method: the highly ordered uniform TiO₂ nanotube arrays were first grown by the conventional electrochemical anodization of the Ti metal sheet followed by mechanical milling of the as-fabricated TiO₂ nanotube arrays. The obtained nanotubes with a length around 400 nm and opening diameter ∼100 nm were formed mixed with the spherical TiO₂ single crystals with a diameter around 10 nm indicating hierarchical nanostructure. The as-synthesized TiO₂ hierarchical nanotubes based resistive-type chemical sensor exhibits good sensitivity to formaldehyde at room temperatures with or without UV-irradiation. The response of the sensor increased almost linearly as a function of the concentration of formaldehyde from 10–50 ppm under UV irradiation. The response of the sensor to different relative humidity and other possible interferents such as ammonia, methanol and alcohol was investigated. The larger response of the sensor to formaldehyde relative to these interferents is suggested to be due to the deeper diffusion of formaldehyde into the TiO₂ nanotubes.     

Influence of erbia or europia doping on crystal structure and microstructure of ceria–zirconia (CZ) solid solutions

In this study we have prepared three zirconia–ceria compositions, namely 12, 50 and 80 mole% CeO₂. Along with each pure ceria–zirconia composition we have prepared two parallel erbia- or europia-doped materials in which 0.5 mole% of each of the two starting oxides is replaced by 1 mole erbia or europia.     

Preparation and characterization of tetragonal-ZrO2 nanopowders by a molten hydroxides method

Pure tetragonal-ZrO₂ nanopowders are prepared by a molten hydroxides method, using hydrated zirconium nitrate as the starting material at 200 °C. X-ray diffraction analysis and transmission electron microscopy observation reveal that the nanopowders exhibit poor crystalline quality. After heat treated at 400 °C for 10 h in air, the nanopowders are crystalline with size range of ∼10–12 nm and most of them are agglomerated. The formation mechanism of the ZrO₂ nanopowders has been proposed. The heat treated nanopowders have a BET surface area of ∼27.3 m²/g due to agglomeration. The photoluminescence of the heat treated nanopowders has been investigated at room temperature.     

Nanorod-assembled spinel Li1.05Mn1.95O4 rods with a central tunnel along the rod-axis for high rate capability of rechargeable lithium-ion batteries

Nanorod-assembled spinel Li_1.05Mn_1.95O₄ rods with a central tunnel along the rod-axis were synthesized using highly crystalline β-MnO₂ rods as self-templates. The synthesized spinel Li_1.05Mn_1.95O₄ is an assembly of several single crystal-like nanorods with an average diameter and length of 100 and 400 nm, respectively, which was determined by microstructural Rietveld refinement using the synchrotron powder XRD data. Galvanostatic battery testing showed that central-tunneled and nanorod-assembled Li_1.05Mn_1.95O₄ rods have a high charge storage capacity at high current densities in comparison with those of the spinel rods without a tunnel structure and commercial powders. Moreover, a capacity retention value of ∼81% was observed at the end of 100 cycles at a current of 250 mAh g⁻¹.     

Effect of annealing process on the growth and surface properties of Au–ZnO nanowire films grown by chemical routes

Au–ZnO nanowire films have been synthesized by chemical routes, electrochemical deposition (ECD) and chemical bath deposition (CBD) techniques, on zinc foil followed by annealing in air at 400 °C. X-ray diffraction patterns reveal formation of the ZnO wurtzite structure along with binary phases Au₃Zn and AuZn₃. Scanning electron microscopy shows the presence of ZnO nanowires having several micrometers in length and less than 120 nm in diameter synthesized by ECD and in the range of 70–400 nm using the CBD technique. During the annealing process, different surface morphologies originating from different catalytic effects of Au atoms/layers were observed. In addition, the effect of synthesis routes on crystalline quality and optical properties were studied by Raman and photoluminescence spectrometers indicating varying concentration of defects on the films. The Raman results indicate that Au–ZnO nanowire film prepared by chemical bath deposition route had better crystalline quality.     

Preparation of Pt/CeO2/HCSs anode electrocatalysts for direct methanol fuel cells

Hollow carbon spheres (HCSs) were prepared through a simple hydrothermal method using silica particles and glucose as the template and carbon precursor, respectively. HCSs used as supports for platinum catalysts deposited with cerium oxide (CeO₂) were prepared for application as anode catalysts in direct methanol fuel cells. The composition and structure of the samples were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The electrocatalytic properties of the as-prepared catalysts for methanol oxidation were investigated by cyclic voltammetry (CV). The Pt/CeO₂/HCSs catalyst heated at 550 °C for 1 h exhibited the best catalytic activity for methanol oxidation.     

Surface modification of 3Y-TZP with cerium oxide

Surface modification with cerium oxide of tetragonal zirconia polycrystals stabilized with 3 mol.% yttria (3Y-TZP) was carried out in order to improve the resistance to low temperature degradation. Specimens were coated with pressed CeO₂ powder and then annealed at 1400 °C and 1500 °C for periods of up to 10 h. Similar treatments were performed in specimens coated with a sub-micron CeO₂ layer by means of magnetron sputtering. Cerium penetration in the surface modified specimens is about 10 μm into the bulk and the grain size increases in the surface layer affected by cerium diffusion. The indentation bulk fracture toughness and Vickers hardness are not affected by the surface modification treatments. Berkovich nanoindentation was performed to observe the contact hardness and elastic modulus at the surface, showing no significant difference after surface modification. Surface modification with ceria induces a large increase in the resistance to hydrothermal ageing without impairing mechanical properties.     

Studies on syntheses and properties of novel CeO2/polyimide nanocomposite films from Ce(Phen)3 complex

A series of cerium dioxide (CeO₂)/polyimide (PI) nanocomposites were successfully prepared from Ce(Phen)₃ and polyamic acid (PAA) via the solution direct-dispersing method, followed by a step thermal imidization process. TGA and XPS studies showed that the cerium complex decomposed to form CeO₂ during the thermal imidization process at 300 °C. SEM observation showed that the formed CeO₂ as nanoparticles was well dispersed in polyimide matrix with a size of about 50-100 nm for samples with different contents of CeO₂. Thermal analysis indicated that the introduction of CeO₂ decreased the thermal stability of nanocomposite films due to the decomposition of Ce(Phen)₃ in the imidization process, while the glass transition temperature (T_g) increased obviously, especially nanocomposite films with high loading of CeO₂ exhibited a trend of disappearance of T_g. DMTA and static tensile measurements showed that the storage modulus of nanocomposite films increased, while the elongation at break decreased with increasing CeO₂ content.     

Synthesis and characterization of Cu-doped ceria nanopowders

Nanopowdered solid solution Ce_1−xCu_xO_2−γ samples (0 ≤ x ≤ 0.15) were synthesized by self-propagating room temperature synthesis (SPRT). Raman spectroscopy and XRD at room temperature were used to study the vibration properties of these materials as well as the Cu solubility in ceria lattice. The solubility limit of Cu²⁺ in CeO₂ lattice was found to be lower than published in the literature. Results show that obtained powders with low dopant concentration are solid solutions with a fluorite-type crystal structure. However, with Cu content higher than 7.5 mass%, the phase separation was observed and two oxide phases, CeO₂ and CuO, coexist. All powders were nanometric in size with high specific surface area.     

Controlled fabrication of nanosized TiO2 hollow sphere particles via acid catalytic hydrolysis/hydrothermal treatment

TiO₂ hollow spheres of controlled size were synthesized by combined acid catalytic hydrolysis and hydrothermal treatment, which involves the deposition of an inorganic coating of TiO₂ on the surface of carbon spheres prepared by a hydrothermal method and subsequent removal of the carbon spheres by calcination in air. The obtained TiO₂ hollow spheres were characterized by scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and powder X-ray diffraction. The results revealed that the size and surface morphology of the TiO₂ hollow spheres can be controlled by adjusting the concentration of the aqueous solution of glucose used to produce the template carbon spheres. Increasing the concentration of the glucose solution increased the average diameter of the TiO₂ hollow spheres from 190 to 300 nm. TiO₂ hollow spheres prepared using a glucose solution with a concentration of 0.7 mol/L are uniform in size with a diameter of 220 nm and shell thickness of 28 nm. The phenol removal rate of the sample prepared by calcination at 600 °C is 1.35 times higher than that of TiO₂ made by the same method without using the carbon template.