V-doped In2O3 nanofibers for H2S detection at low temperature

Pristine and vanadium-doped In₂O₃ nanofibers were fabricated by electrospinning and their sensing properties to H₂S gas were studied. X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to investigate the inner structure and the surface morphology. The H₂S-sensing performances were characterized at different temperatures ranging from 50 to 170 °C. The sensor based on 6 mol% V-doped In₂O₃ nanofibers exhibit the highest response, i.e. 13.9–50 ppm H₂S at the relatively low temperature of 90 °C. In addition, the fast response (15 s) and recovery (18 s) time, and good selectivity were observed.     

Sol-gel derived 6CaO·6SrO·7Al2O3 thin films using metal alkoxides

The novel 6CaO·6SrO·7Al₂O₃ (C6S6A7) thin films were deposited onto soda lime glass substrate using calcium, strontium, aluminium isopropoxide and 2-methoxy ethanol as starting materials via sol-gel dip coating technique. The electrical and optical properties of C6S6A7 films were investigated for films sample annealed at 450 °C for 2 h in air and hydrogen (H₂) atmosphere, respectively. X-ray diffraction pattern and Fourier transformed infrared spectroscopy analysis confirms cubic structure to the C6S6A7 material. The optical transmission spectra of C6S6A7 films showed the high transparency in wide visible range of ∼ 88 and 80% for air and H₂ annealed samples, respectively. The C6S6A7 films sheet resistance of 528 and 0.65 k Ohm/square has been observed for films annealed in air and H₂ atmosphere at 450 °C, respectively.     

Soft template synthesis of mesoporous Co3O4/RuO2·xH2O composites for electrochemical capacitors

Co₃O₄/RuO₂·xH₂O composites with various Ru content (molar content of Ru = 5%, 10%, 20%, 50%) were synthesized by one-step co-precipitation method. The precursors were prepared via adjusting pH of the mixed aqueous solutions of Co(NO₃)₂·6H₂O and RuCl₃·0.5H₂O by using Pluronic123 as a soft template. For the composite with molar ratio of Co:Ru = 1:1 annealed at 200 °C, Brunauer-Emmet-Teller (BET) results indicated that the composite showed mesoporous structure, and the specific surface area of the composite was as high as 107 m² g⁻¹. The electrochemical performances of these composites were measured in 1 M KOH electrolyte. Compared with the composite prepared without template, the composite with P123 exhibited a higher specific capacitance. When the molar content of Ru was rising, the specific capacitance of the composites increased significantly. It was also observed that the crystalline structures as well as the electrochemical activities were strongly dependent on the annealing temperature. A capacitance of 642 F/g was obtained for the composite (Co:Ru = 1:1) annealed at 150 °C. Meanwhile, the composites also exhibited good cycle stability. Besides, the morphologies and textural characteristic of the samples were also investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM).     

Controllable synthesis and flame retardant properties of bunch-, chrysanthemum-, and plumy-like 4ZnO·B2O3·H2O nanostructures

Three kinds of new 4ZnO·B₂O₃·H₂O nanostructures of bunch-, chrysanthemum-, and plumy-like morphologies have been synthesized under hydrothermal conditions at 140 °C in the presence of ethanol. The as-synthesized products were characterized by the chemical analysis, TG, XRD, FT-IR, SEM and TEM. All the synthesized 4ZnO·B₂O₃·H₂O nanostructures consist of nanoribbons. A series of control experiments confirmed that the morphologies of the products were influenced by the reaction time, temperature, and the presence of the surfactant of PEG-300. Furthermore, the flame retardant properties of the synthesized 4ZnO·B₂O₃·H₂O nanostructures were investigated by the thermal analysis method, demonstrating that they had the better behaviors than the non-nanostructure sample.     

Formation of LiNi0.5Co0.5VO4 nano-crystals by solvothermal reaction

LiNi_0.5Co_0.5VO₄ nano-crystals were solvothermally prepared using a mixture of LiOH·H₂O, Ni(NO₃)₂·6H₂O, Co(NO₃)₂·6H₂O and NH₄VO₃ in isopropanol at 150–200 °C followed by 300–600 °C calcination to form powders. TGA curves of the solvothermal products show weight losses due to evaporation and decomposition processes. The purified products seem to form at 500 °C and above. The products analyzed by XRD, selected area electron diffraction (SAED), energy dispersive X-ray (EDX) and atomic absorption spectrophotometer (AAS) correspond to LiNi_0.5Co_0.5VO₄. V–O stretching vibrations of VO₄ tetrahedrons analyzed using FTIR and Raman spectrometer are in the range of 620–900 cm⁻¹. A solvothermal reaction at 150 °C for 10 h followed by calcination at 600 °C for 6 h yields crystals with lattice parameter of 0.8252 ± 0.0008 nm. Transmission electron microscope (TEM) images clearly show that the solvothermal temperatures play a more important role in the size formation than the reaction times.     

Precursor effects on ZrW2O8 formation kinetics

The synthesis of ZrW₂O₈ from different kinds of mixtures containing ZrO₂–WO₃, ZrO(NO₃)₂·2H₂O–WO₃, ZrCl₂O·8H₂O–WO₃, and ZrO₂–(NH₄)₁₀W₁₂O₄₁·5H₂O was investigated, and the kinetics was analyzed using JMA equation. It was found that ZrO(NO₃)₂·2H₂O, ZrCl₂O·8H₂O H₂O and (NH₄)₁₀W₁₂O₄₁·5H₂O that were used as inorganic precursors formed ZrO₂ and WO₃ after firing above 500 °C. The content of ZrW₂O₈ obtained by firing the mixtures is influenced by the kinds of precursors as well as mixing methods. The formation rate of ZrW₂O₈ depends on homogeneity related to mixing methods as well as the particle size of starting powders. Phase-pure ZrW₂O₈ is obtained from the ZrCl₂O·8H₂O–WO₃ mixtures at 1200 °C for 4 h, which is much shorter time than in the case of conventional ZrO₂–WO₃ mixtures. In the reaction kinetics of ZrO₂–WO₃ system, the Avrami exponent (n) is ∼0.5 above 1175 °C, indicating that the reaction is controlled by the diffusion-controlled reaction.     

Selective synthesis of mixed alcohols from syngas over catalyst Fe2O3/Al2O3 in slurry reactor

The Fe₂O₃/Al₂O₃ catalyst was studied to selectively synthesize mixed alcohols from syngas in a continuously stirred slurry reactor with the oxygenated solvent Polyethylene Glycol-400 (PEG-400). The selectivity of mixed alcohols in the products reached as high as 95 wt.% and the C₂₊ alcohols (mainly ethanol) was more than 40 wt.% in the total alcohol products at the reaction conditions of 250 °C, 3.0 MPa, H₂/CO = 2 and space velocity = 360 ml/g_cat h. The hydrogen temperature programmed reduction (H₂-TPR) and X-ray photoelectron spectroscopy (XPS) measurements of the catalyst confirmed that the FeO phase was responsible for the high selectivity to mixed alcohols in the process. And the oxygenated solvent PEG-400 was also necessary for the selective synthesis of mixed alcohols in the reaction system.     

Reduction behaviors and catalytic properties for methanol steam reforming of Cu-based spinel compounds CuX2O4 (X=Fe,Mn, Al,La)

In this study, various Cu-based spinel compounds, i.e., CuFe₂O₄, CuMn₂O₄, CuAl₂O₄ and CuLa₂O₄, were fabricated by a solid-state reaction method. Reduction behaviors and morphological changes of these materials have been characterized by H₂ temperature-programmed reduction (H₂-TPR), X-ray diffraction (XRD), Scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Moreover, the catalytic properties for steam reforming of methanol (SRM) of these Cu-based spinel compounds were investigated. H₂-TPR results indicated that the reducibility of Cu-based spinel compounds was strongly dependent on the B-site component while the CuFe₂O₄ catalyst revealed the lowest reduction temperature (190 °C), followed respectively by CuAl₂O₄ (267 °C), CuMn₂O₄ (270 °C), and CuLa₂O₄ (326 °C). The reduced CuAl₂O₄ catalyst demonstrated the best performance in terms of catalytic activity. Based on the SEM and XRD results, pulverization of the CuAl₂O₄ particles due to gas evolution and a high concentration of nanosized Cu particles (≈50.9 nm) precipitated on the surfaces of the Al₂O₃ support were observed after reduction at 360 °C in H₂. The BET surface area of the CuAl₂O₄ catalyst escalated from 5.5 to 13.2 m²/g. Reduction of Cu-based spinel ferrites appear to be a potential synthesis route for preparing a catalyst with high catalytic activity and thermal stability. The catalytic performance of these copper-oxide composites was superior to those of conventional copper catalysts.     

RuO2·xH2O/NiO composites as electrodes for electrochemical capacitors: Effect of the RuO2 content and the thermal treatment on the specific capacitance

RuO₂·xH₂O/NiO composites having RuO₂ contents in the range 0-100 wt.% have been prepared by a co-precipitation method. Structural, microstructural and textural transformations after heating the as-prepared composites at 200 and 600 °C have been followed by X-ray diffraction, scanning electron microscopy (SEM) and nitrogen adsorption/desorption isotherms. At 200 °C the composites are made of micrometric particles in which nanometric crystallites of the two oxides are aggregated. The composites show microporosity (0.02-0.10 cm³/g), mesoporosity (0.07-0.12 cm³/g) and relatively high specific surface area (62-309 m²/g). At 600 °C the composites are fully dehydrated and RuO₂ has crystallized and segregated. Microporosity and mesoporosity as well as specific surface area are strongly decreased. Specific capacitance and specific surface area of the composites heated at 200 and 600 °C have been measured and discussed on the basis of the RuO₂ content. For comparison the specific capacitance and specific surface area of mixtures of NiO and RuO₂·xH₂O (or RuO₂) have been taken as references. The higher specific capacitance of the 200 °C-heated composites compared to the 600 °C-heated ones is due to the higher specific surface area of the former and the higher pseudocapacitance of RuO₂·xH₂O compared to RuO₂. The discussion reported in this work can be applied to other composites such as RuO₂·xH₂O/carbon and RuO₂·xH₂O/other oxides.     

Synthesis and electrochemical characterization of nano-CeO2-coated nanostructure LiMn2O4 cathode materials for rechargeable lithium batteries

LiMn₂O₄ spinel cathode materials were coated with 0.5, 1.0, and 1.5 wt.% CeO₂ by a polymeric process, followed by calcination at 850 °C for 6 h in air. The surface-coated LiMn₂O₄ cathode materials were physically characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron microscopy (XPS). XRD patterns of CeO₂-coated LiMn₂O₄ revealed that the coating did not affect the crystal structure or the Fd3m space group of the cathode materials compared to uncoated LiMn₂O₄. The surface morphology and particle agglomeration were investigated using SEM, TEM image showed a compact coating layer on the surface of the core materials that had average thickness of about 20 nm. The XPS data illustrated that the CeO₂ completely coated the surface of the LiMn₂O₄ core cathode materials. The galvanostatic charge and discharge of the uncoated and CeO₂-coated LiMn₂O₄ cathode materials were measured in the potential range of 3.0-4.5 V (0.5 C rate) at 30 °C and 60 °C. Among them, the 1.0 wt.% of CeO₂-coated spinel LiMn₂O₄ cathode satisfies the structural stability, high reversible capacity and excellent electrochemical performances of rechargeable lithium batteries.     

Efficient production of hydrogen and multi-walled carbon nanotubes from ethanol over Fe/Al2O3 catalysts

Fe/Al₂O₃ catalysts with different Fe loadings (10-90 mol%) were prepared by hydrothermal method. Ethanol decomposition was studied over these Fe/Al₂O₃ catalysts at temperatures between 500 and 800 °C to produce hydrogen and multi-walled carbon nanotubes (MWCNTs) at the same time. The results showed that the catalytic activity and stability of Fe/Al₂O₃ depended strongly on the Fe loading and reaction temperature. The Fe(30 mol%)/Al₂O₃ and Fe(40 mol%)/Al₂O₃ were both the effective catalyst for ethanol decomposition into hydrogen and MWCNTs at 600 °C. Several reaction pathways were proposed to explain ethanol decomposition to produce hydrogen and carbon (including nanotube) at the same time.     

Grass blade-like microparticle MnPO4·H2O prepared by a simple precipitation at room temperature

Grass blade-like microparticle MnPO₄·H₂O was synthesized by a simple precipitation at room temperature using a mixture of manganese sulphate monohydrate, phosphoric acid and water at pH = 7. The thermogravimetric study indicates that the synthesized compound is stable below 500 °C and its final decomposed product is Mn₂P₂O₇. The pure monoclinic phases of the synthesized MnPO₄·H₂O and its final decomposed product Mn₂P₂O₇ are verified by XRD data. FTIR spectra indicate the presences of the PO₄³⁻ ion and water molecules in the MnPO₄·H₂O structure and the P₂O₇⁴⁻ ion in the Mn₂P₂O₇ structure. The thermal stability, crystallite size, and grass blade-like microparticle of MnPO₄·H₂O in this work are different from previous reports, which may be caused by the starting reagents and reaction condition for the precipitation.     

Heteropolyacid in glass electrolytes for the development of H2/O2 fuel cells

The scope of the present work was to investigate and evaluate the electrochemical activity of H₂/O₂ fuel cells based on the influence of a heteropolyacid glass membrane with a Pt/C electrode at low temperature. A new trend of sol-gel derived PMA (H₃PMo₁₂O₄₀) heteropolyacid-containing glass membranes inherent of a high proton conductivity and mechanical stability, was heat treated at 600 °C and implemented to H₂/O₂ fuel cell activities through electrochemical characterization. Significant research has been focused on the development of H₂/O₂ fuel cells using optimization of heteropolyacid glasses as electrolytes with Pt/C electrodes at 30 °C. A maximum power density of 23.9 mW/cm² was attained for operation with hydrogen and oxygen, respectively, at 30 °C and 30% humidity with the PMA glass membranes (4-92-4 mol%). Impedance spectroscopy measurements were performed on a total ohmic cell resistance of a membrane-electrode-assembly (MEA) at the end of the experiment.     

Large-scale synthesis of WO3 nanoplates by a microwave-hydrothermal method

Tungsten oxide (WO₃) nanoplates were synthesized by a 270 W microwave-hydrothermal reaction of Na₂WO₄·2H₂O and citric acid (C₆H₈O₇·H₂O) in deionized water. X-ray diffraction (XRD), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), and selected area electron diffraction (SAED) were used to reveal the synthesis of WO₃ complete rectangular nanoplates in the solution of 0.2 g citric acid for 180 min, with O-W-O FTIR stretching modes at 819 and 741 cm⁻¹, and two prominent O-W-O Raman stretching modes at 804 and 713 cm⁻¹. The 2.71 eV indirect energy gap, and 430-460 nm blue emission wavelength range of WO₃ complete rectangular nanoplates were determined using UV-visible and photoluminescence (PL) spectrometers. The formation mechanism was also proposed according to the experimental results.     

Fixed- and fluidised-bed synthesis of coiled carbon fibres on an in situ generated H2S-modified Ni/Al2O3 catalyst from a NiSO4/Al2O3 precursor

NiSO₄/Al₂O₃ and NiO/Al₂O₃ catalyst precursors were formed by calcination of NiSO₄·6H₂O/Al₂O₃ at 500 and 800 °C, respectively. The catalyst precursor was reduced under H₂ and N₂ and then reacted under C₂H₂, H₂ and N₂ at 650 °C. Coiled carbon fibres were formed in fixed- and fluidised-bed reactors using the NiSO₄/Al₂O₃ catalyst precursor. Thermodynamic modelling using an infinite equilibrium stage construction predicted complete reduction of NiSO₄ to Ni and simultaneous H₂S formation occurs in both fixed- and fluidised-bed systems. XRD measurements confirmed that Ni was the only catalytically active crystalline species present at concentrations >0.5 wt.% (XRD detection limit) post-reduction, however XRF and XPS measurements additionally detected the presence of small quantities (<0.9 wt.% S) of S species. S is adsorbed onto the Ni surfaces during reduction when H₂S is released and dissociates on the Ni surface. Non-coiled carbon fibres produced on the Ni/Al₂O₃ catalyst formed from the NiO/Al₂O₃ precursor demonstrated that modification of Ni/Al₂O₃ with S is required for coiled carbon fibre synthesis.     

Iron-enriched natural zeolite modified carbon paste electrode for H2O2 detection

This work demonstrates that iron-enriched natural zeolitic volcanic tuff (Paglisa deposit, Cluj county, Transilvania, Romania) resulting from a previous use as adsorbent in wastewater treatment can be recycled into effective electrode modifier applied to the electrocatalytic detection of hydrogen peroxide. After physico-chemical characterization of tuff samples using various techniques such as chemical analysis, X-ray diffraction, scanning electron microscopy, infrared spectroscopy, BET analysis and X-ray photoelectron spectroscopy, the electrochemical response of the iron-enriched zeolites was studied on the basis of solid carbon paste electrodes modified with these samples. The results indicate that iron centers in the zeolite are electroactive and that they act as electrocatalysts in the voltammetric and amperometric detection of H₂O₂. Best performance was achieved in phosphate buffer at pH 7, showing a sensitivity of 0.57 mA M⁻¹ cm⁻², a detection limit down to 60 μM, and a linear domain up to 100 mM H₂O₂.     

Deposition behavior and characteristics of hydroxyapatite coatings on Al2O3, Ti,and Ti6Al4V formed by a chemical bath method

A simple chemical bath method was used to deposit hydroxyapatite (HA) coatings on Al₂O₃, Ti, and Ti6Al4V substrates at ambient pressure by heating to 65–95 °C in an aqueous solution prepared with Ca(NO₃)₂·4H₂O, KH₂PO₄, KOH, and EDTA. The deposition behavior, morphology, thickness, and phase of the coatings were investigated using scanning electron microscopy and X-ray diffractometry. The bonding strength of the coatings was measured using an epoxy resin method. The HA coatings deposited on the three kinds of substrates were fairly dense and uniform and exhibited good crystallinity without any additional heat treatment. A coating thickness of 1–1.8 μm was obtained for the samples coated once. By repeating the coating process three times, the thickness could be increased to 4.5 μm on the Al₂O₃ substrate. The bonding strength of these coatings was 18 MPa.     

Simple fabrication of polyhedral grain-like microparticle Cu0.5Zn0.5HPO4·H2O and porous structure CuZnP2O7

Polyhedral grain-like microparticle Cu_0.5Zn_0.5(HPO₄)·H₂O was simply synthesized by heterogeneous reaction using a mixture of CuCO₃, ZnO, phosphoric acid and water at room temperature for 30 min. The thermogravimetric study indicates that the synthesized compound is stable below 250 °C and its final decomposed product is CuZnP₂O₇. The pure monoclinic phases of the synthesized Cu_0.5Zn_0.5(HPO₄)·H₂O and its final decomposed product CuZnP₂O₇ are verified by XRD data. The presences of the HPO₄²⁻ ion and H₂O molecule in the Cu_0.5Zn_0.5(HPO₄)·H₂O structure and the P₂O₇⁴⁻ ion in the CuZnP₂O₇ structure are confirmed by FTIR data. The thermal stability, the morphology based on polyhedral grain-like microparticles and porous structure of the studied compounds are different from previously reported phosphates, and may affect their activities for potential applications (catalysis, electronics, etc.).     

Transmission electron microscopy characterization of nanostructured carbon derived from Cr3C2 and Cr(C5H7O2)3

The preparation, characterization and comparison of nanostructured carbons derived by direct chlorination of Cr₃C₂ and Cr(C₅H₇O₂)₃ are reported in this work. Cr₃C₂ precursor was treated at 400 and 900 °C with a reaction time of 1 h. The nanostructure of the products has been characterized in some detail by means of transmission electron microscopy and associated techniques, such as electron energy-loss and X-ray energy dispersive spectroscopies and high-angle annular dark field imaging. Remains of Cr₃C₂ encapsulated in an amorphous carbon shell were observed at 400 °C, whereas carbon with higher ordering degree was produced at 900 °C. In the latter case, the sample can be described as a continuous variation from poorly-stacked graphene-like carbon to graphitic agglomerates. Remains of the reaction by-product, CrCl₃, are detected in the carbon particles, forming monolayers intercalated inside the graphitic agglomerates and amorphous nanoparticles. As a comparison, carbon samples derived from Cr(C₅H₇O₂)₃ were prepared at 300 and 900 °C. They mainly consist of highly disordered carbon, with local graphite-like stacking in the sample prepared at 900 °C.     

Formation and characterization of iron oxide nanoparticles loaded on self-organized TiO2 nanotubes

The iron oxide nanoparticles were loaded onto self-organized TiO₂ nanotube layers grown by anodization of Ti in fluoride containing electrolytes. The nanoparticles were obtained by electrodepositing method in glycerol/water/FeCl₃·6H₂O electrolytes at room temperature. The X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM) and X-ray photoelectron spectroscopy (XPS) measurements showed that the nanoparticles consisted of iron nanocrystalline (Fe) and magnetite (Fe₃O₄). The hematite (α-Fe₂O₃) structure was obtained by annealing in air at 450 °C. The growth mechanism of the nanoparticles and their morphology were also described. Furthermore, the nanoparticles exhibited good ferromagnetic properties at room temperature.