V-doped In2O3 nanofibers for H2S detection at low temperature

Pristine and vanadium-doped In₂O₃ nanofibers were fabricated by electrospinning and their sensing properties to H₂S gas were studied. X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to investigate the inner structure and the surface morphology. The H₂S-sensing performances were characterized at different temperatures ranging from 50 to 170 °C. The sensor based on 6 mol% V-doped In₂O₃ nanofibers exhibit the highest response, i.e. 13.9–50 ppm H₂S at the relatively low temperature of 90 °C. In addition, the fast response (15 s) and recovery (18 s) time, and good selectivity were observed.     

Catalytic steam reforming of ethane and propane over CeO2-doped Ni/Al2O3 at SOFC temperature: Improvement of resistance toward carbon formation by the redox property of doping CeO2

Ni/Al₂O₃ with the doping of CeO₂ was found to have useful activity to reform ethane and propane with steam under Solid Oxide Fuel Cells (SOFCs) conditions, 700-900 °C. CeO₂-doped Ni/Al₂O₃ with 14% ceria doping content showed the best reforming activity among those with the ceria content between 0 and 20%. The amount of carbon formation decreased with increasing Ce content. However, Ni was easily oxidized when more than 16% of ceria was doped. Compared to conventional Ni/Al₂O₃, 14%CeO₂-doped Ni/Al₂O₃ provides significantly higher reforming reactivity and resistance toward carbon deposition. These enhancements are mainly due to the influence of the redox properties of doped ceria. Regarding the temperature programmed reduction experiments (TPR-1), the redox properties and the oxygen storage capacity (OSC) for the catalysts increased with increasing Ce doping content. In addition, it was also proven in the present work that the redox of these catalysts are reversible, according to the temperature programmed oxidation (TPO) and the second time temperature programmed reduction (TPR-2) results.During the reforming process, in addition to the reactions on Ni surface, the gas-solid reactions between the gaseous components presented in the system (C₂H₆, C₃H₈, C₂H₄, CH₄, CO₂, CO, H₂O, and H₂) and the lattice oxygen (O_x) on ceria surface also take place. The reactions of adsorbed surface hydrocarbons with the lattice oxygen (O_x) on ceria surface (C_nH_m+O_x→nCO+m/2(H₂)+O_x−n) can prevent the formation of carbon species on Ni surface from hydrocarbons decomposition reaction (C_nH_m⇔nC+m/2H₂). Moreover, the formation of carbon via Boudard reaction (2CO⇔CO₂+C) is also reduced by the gas-solid reaction of carbon monoxide (produced from steam reforming) with the lattice oxygen (CO+O_x⇔CO₂+O_x−1).     

Ni-doped TiO2 nanotubes for wide-range hydrogen sensing

Doping of titania nanotubes is one of the efficient way to obtain improved physical and chemical properties. Through electrochemical anodization and annealing treatment, Ni-doped TiO₂ nanotube arrays were fabricated and their hydrogen sensing performance was investigated. The nanotube sensor demonstrated a good sensitivity for wide-range detection of both dilute and high-concentration hydrogen atmospheres ranging from 50 ppm to 2% H₂. A temperature-dependent sensing from 25°C to 200°C was also found. Based on the experimental measurements and first-principles calculations, the electronic structure and hydrogen sensing properties of the Ni-doped TiO₂ with an anatase structure were also investigated. It reveals that Ni substitution of the Ti sites could induce significant inversion of the conductivity type and effective reduction of the bandgap of anatase oxide. The calculations also reveal that the resistance change for Ni-doped anatase TiO₂ with/without hydrogen absorption was closely related to the bandgap especially the Ni-induced impurity level.     

Sequential production of H2 and CO over supported Ni catalysts

Methane decomposition into H₂ and carbon nanofibers at 823 K and subsequent gasification of the carbon nanofibers with CO₂ into CO at 923 K were performed over supported Ni catalysts (Ni/SiO₂, Ni/TiO₂ and Ni/Al₂O₃). Supported Ni catalysts were deactivated for CH₄ decomposition with time on stream due to deposition of a large amount of carbon nanofibers. Subsequent contact of CO₂ with carbon nanofibers on the deactivated catalysts resulted in the formation of CO with a conversion of the carbons higher than 95%. In addition, gasification with CO₂ regenerated the activity of supported Ni catalysts for CH₄ decomposition, indicating that H₂ formation through CH₄ decomposition and CO formation through gasification with CO₂ could be carried out repeatedly. Conversions of carbon nanofibers into CO were kept higher than 95% in the repeated gasification over all the catalysts, while change in the catalytic activity for CH₄ decomposition with the repeated cycles depended on the kind of catalytic supports. Catalytic activity of Ni/SiO₂ for CH₄ decomposition was high at early cycles, however, the activity decreased gradually with the repeated cycles. On the other hand, Ni/TiO₂ and Ni/Al₂O₃ showed high activity for CH₄ decomposition and the activity was kept high during the repeated cycles. These changes of catalytic activities for CH₄ decomposition could be explained by changes in particle sizes of Ni metal, i.e. Ni metal particles in Ni/SiO₂ aggregated into ones larger than 150 nm with the repeated cycles, while the particle sizes of Ni metal in Ni/TiO₂ and Ni/Al₂O₃ remained at an effective range for CH₄ decomposition (60-100 nm).     

Mn2O3/TiO2 nanofibers with broad-spectrum antibiotics effect and photocatalytic activity for preliminary stage of water desalination

Composite nanofibers consisting of Mn₂O₃ and TiO₂ were prepared by the electrospinning process, and tested as Gram-class-independent antibacterial agent and photocatalyst for organic pollutants degradation. Initially, electrospinning of a sol–gel consisting of titanium isopropoxide, manganese acetate tetrahydrate and poly(vinyl pyrrolidone) was used to produce hybrid polymeric nanofibers. Calcination of the obtained nanofibers in air at 650 °C led to produce good morphology Mn₂O₃/TiO₂ nanofibers. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were employed to characterize the as-spun nanofibers and the calcined product. X-ray powder diffractometry (XRD) analysis was also used to characterize the chemical composition and the crystallographic structure of the sintered nanofibers. The antibacterial activity of Mn₂O₃/TiO₂ nanofibers against Gram negative and Gram positive bacteria was investigated by calculating the minimum inhibitory concentration after treatment with the nanofibers. Investigations revealed that the lowest concentration of Mn₂O₃/TiO₂ nanofibers solution inhibiting the growth of Staphylococcus aureus ATCC 29231 and Escherichia coli ATCC 52922 strains is 0.4 and 0.8 μg/ml, respectively. Incorporation of Mn₂O₃ significantly improved the photodegradation of methylene blue (MB) dye under the visible light irradiation due to enhancing rutile phase formation in the TiO₂ nanofibers matrix.     

Highly active and coking resistant Ni/CeO2-ZrO2 catalyst for partial oxidation of methane

Nickel catalysts over the CeO₂-ZrO₂ solid solution were successfully prepared by the co-precipitation method for partial oxidation of methane. The structures of the catalysts were systematically examined by N₂ adsorption/desorption, CO chemisorption, X-ray diffraction (XRD) and H₂-TPR techniques. The catalytic performance and carbon deposition were investigated for partial oxidation of methane as well. The results showed that the Ni/CeO₂-ZrO₂ catalysts had a large BET area and fine Ni dispersion. By the co-precipitation method, Ni and CeO₂-ZrO₂ solid solution had strong interaction confirmed by the H₂-TPR analysis. The Ni/CeO₂-ZrO₂ catalysts showed high activity and stability and the Ni/Ce_0.25Zr_0.75O₂ exhibited the best activity and coking resistance among these catalysts. The catalytic activities and coking resistant behaviors of catalysts were affected by the surface and structural properties of the catalysts.     

Characterization of aerogel Ni/Al2O3 catalysts and investigation on their stability for CH4-CO2 reforming in a fluidized bed

The CH₄-CO₂ reforming was investigated in a fluidized bed reactor using nano-sized aerogel Ni/Al₂O₃ catalysts, which were prepared via a sol–gel method combined with a supercritical drying process. The catalysts were characterized with BET, XRD, H₂-TPR and H₂-TPD techniques. Compared with the impregnation catalyst, aerogel catalysts exhibited higher specific surface areas, lower bulk density, smaller Ni particle sizes, stronger metal-support interaction and higher Ni dispersion degrees. All tested aerogel catalysts showed better catalytic activities and stability than the impregnation catalyst. Their catalytic stability tested during 48 h reforming was dependent on their Ni loadings. Characterizations of spent catalysts indicated that only limited graphitic carbon formed on the aerogel catalyst, while massive graphitic carbon with filamentous morphology was observed for the impregnation catalyst, leading to significant catalytic activity degradation. An aerogel catalyst containing 10% Ni showed the best catalytic stability and the lowest rate of carbon deposition among the aerogel catalysts due to its small Ni particle size and strong metal-support interaction.     

Enhancement of the photocatalytic performance of Ni-loaded TiO2 photocatalyst under sunlight

A highly sunlight active Ni-loaded TiO₂ nanocomposite (Ni/TiO₂) is successfully prepared by a simple chemical reduction method using tetrabutyl titanate as a precursor, Ni(NO₃)₂·6H₂O as a nickel source, and N₂H₄·H₂O as a reductant, respectively. The crystal structure, morphology and UV–vis diffuse reflectance characteristics are investigated by XRD, TEM, and UV–vis diffuse reflectance spectroscopy, while the photocatalytic performance of Ni/TiO₂ is evaluated by photocatalytic degradation of methyl orange solution under UV and sunlight irradiation. Results show that the crystal structure of TiO₂ is not changed upon the loading of Ni, the photocatalytic performance of TiO₂ under both UV-light and sunlight, however, is enhanced greatly. The enhancement of the photocatalytic performance of Ni/TiO₂ is attributed to the increase of the photogenerated electron–hole separation efficiency and the advanced absorption of light due to surface plasmon effect of Ni nanoparticles.     

Steam reforming of LPG over Ni and Rh supported on Gd-CeO2 and Al2O3: Effect of support and feed composition

The steam reforming of liquefied petroleum gas (LPG) over Ni- and Rh-based catalysts supported on Gd-CeO₂ (CGO) and Al₂O₃ was studied at 750-900 °C. The order of activity was found to be Rh/CGO > Ni/CGO ∼ Rh/Al₂O₃ > Ni/Al₂O₃; we indicated that the comparable activity of Ni/CGO to precious metal Rh/Al₂O₃ is due to the occurring of gas-solid reactions between hydrocarbons and lattice oxygen () on CGO surface along with the reaction taking place on the active site of Ni, which helps preventing the carbon deposition and promoting the steam reforming of LPG.The effects of O₂ (as oxidative steam reforming) and H₂ adding were further studied over Ni/CGO and Ni/Al₂O₃. It was found that the additional of these compounds significantly reduced the amount of carbon deposition and promoted the conversion of hydrocarbons (i.e., LPG as well as CH₄, C₂H₄ and C₂H₆ occurred from the thermal decomposition of LPG) to CO and H₂. Nevertheless, the addition of too high O₂ oppositely decreased H₂ yield due to the oxidizing of Ni particle and the possible combusting of H₂ generated from the reaction, while the addition of too high H₂ also negatively affect the catalyst activity due to the occurring of catalyst active site competition and the inhibition of gas-solid reactions between the gaseous hydrocarbon compounds and on the surface of CGO (for the case of Ni/CGO).     

Studies on the resistive response of nickel and cerium doped SnO2 thick films to acetone vapor

Undoped and Ni, Ce-doped nanocrystalline tin oxide were synthesized by co-precipitation route. Doped as well as undoped SnO₂ compositions revealed single phase structure without any impurity. The lattice constant of SnO₂ increases and the grain size decreases with doping of Ni and Ce. The responses of the sensing elements are evaluated by measuring the resistance change upon exposure to various test gases such as liquid petroleum gas (LPG), acetone, ethanol and ammonia. In comparison to LPG, ethanol, and ammonia the response towards acetone vapor increases markedly on simultaneous doping of Ni and Ce. For acetone vapors with 500 ppm at 300 °C, the undoped SnO₂ shows 31% response, while with individual Ni or Ce doping it increases to 38 and 60%, respectively, however with simultaneous doping of Ni and Ce there is a significant enhancement up to 92%. The results of gas sensing measurements reveal that the thick films deposited on alumina substrates using screen printing technique give selectively a high response of (87%) with fast recovery (∼1 min) towards 100 ppm acetone at 300 °C.     

Microstructural, crystal structure and electrical characteristics of shock-consolidated Ga2O3 doped ZnO bulk

Ga₂O₃ (5 wt.%) doped zinc oxide (ZnO, 95 wt.%) bulk was fabricated by underwater shock compaction technique. The microstructural, crystal structure and electrical properties of shock-consolidated samples were investigated and compared to a commercially available sintered Ga₂O₃ (5 wt.%) doped ZnO (95 wt.%). The relative density of shock-consolidated sample was about 97% of the theoretical density, and no grain growth and lattice defects were confirmed. The grain boundary resistance was remarkably higher than that of commercial sintered Ga₂O₃ doped ZnO and nonlinear current-voltage (I-V) characteristics of shock-consolidated ZnO and Ga₂O₃ doped ZnO were very lower than that of commercial ZnO varistor.     

Preparation of NaBiO3 and the electrochemical characteristic of manganese dioxide doped with NaBiO3

NaBiO₃ crystal of high purity has been synthesized through chemical oxidization. The morphology and thermal stability of NaBiO₃ were examined with scanning electron microscope (SEM) and thermogravimetry-differential scanning calorimetry (TG-DSC). The electrochemical properties of MnO₂ electrodes with and without doping NaBiO₃ were studied through galvanostatic charge/discharge and cyclic voltammetry. The results indicate that the MnO₂ electrode doped with NaBiO₃ possesses remarkably higher discharge voltage and capacity and better reversibility than the pure MnO₂ electrode and Bi₂O₃ doping MnO₂ electrode.     

CO2 hydrogenation to methanol over Cu/ZnO/ZrO2 catalysts prepared via a route of solid-state reaction

Cu/ZnO/ZrO₂ catalysts were prepared by a route of solid-state reaction and tested for the synthesis of methanol from CO₂ hydrogenation. The effects of calcination temperature on the physicochemical properties of as-prepared catalysts were investigated by N₂ adsorption, XRD, TEM, N₂O titration and H₂-TPR techniques. The results show that the dispersion of copper species decreases with the increase in calcination temperature. Meanwhile, the phase transformation of zirconia from tetragonal to monoclinic was observed. The highest activity was achieved over the catalyst calcined at 400 °C. This method is a promising alternative for the preparation of highly efficient Cu/ZnO/ZrO₂ catalysts.     

Influence of the Type of Reducing Agent (H2, CO, C3H6 and C3H8) on the Reduction of Stored NOX in a Pt/BaO/Al2O3 Model Catalyst

In this investigation, a comparative study for a NO _X storage catalytic system was performed focusing on the parameters that affect the reduction by using different reductants (H₂, CO, C₃H₆ and C₃H₈) and different temperatures (350, 250 and 150 °C), for a Pt/BaO/Al₂O₃ catalyst. Transient experiments show that H₂ and CO are highly efficient reductants compared to C₃H₆ which is somewhat less efficient. H₂ shows a significant reduction effect at relatively low temperature (150 °C) but with a low storage capacity. We find that C₃H₈does not show any NO _X reduction ability for NO _X stored in Pt/BaO/Al₂O₃ at any of the temperatures. The formation of ammonia and nitrous oxide is also discussed.     

Synthesis of Fe2O3 nanoparticles for nitrogen dioxide gas sensing applications

Iron (III) oxide, Fe₂O₃, nanoparticles of approximately 40 nm diameter were synthesized by sol–gel method and their nitrogen dioxide adsorption and desorption kinetics were investigated by custom fabricated gas sensor unit. The morphology and crystal structure of Fe₂O₃ nanoparticles were studied by scanning electron microscopy (SEM), field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) respectively. The roughness of film surface was investigated by atomic force microscopy (AFM). Relative sensitivity of Fe₂O₃ nanoparticles for NO₂ sensor was determined by electrical resistance measurements. Our reproducible experimental results show that Fe₂O₃ nanoparticles have a great potential for nitrogen dioxide sensing applications operating at a temperature of 200 °C.     

Synthesis and tunable thermal expansion properties of Sc2−xYxW3O12 solid solutions

A new series of rare earth solid solutions Sc_2−xY_xW₃O₁₂ was successfully synthesized by the conventional solid-state method. Effects of doping ion yttrium on the crystal structure, morphology and thermal expansion property of as-prepared Sc_2−xY_xW₃O₁₂ ceramics were investigated by X-ray diffraction (XRD), thermogravimetric analysis (TG), field emission scanning electron microscope (FE-SEM) and thermal mechanical analyzer (TMA). Results indicate that the obtained Sc_2−xY_xW₃O₁₂ samples with Y doping of 0≤x≤0.5 are in the form of orthorhombic Sc₂W₃O₁₂-structure and show negative thermal expansion (NTE) from room temperature to 600 °C; while as-synthesized materials with Y doping of 1.5≤x≤2 take hygroscopic Y₂W₃O₁₂·nH₂O-structure at room temperature and exhibit NTE only after losing water molecules. It is suggested that the obvious difference in crystal structure leads to different thermal expansion behaviors in Sc_2−xY_xW₃O₁₂. Thus it is proposed that thermal expansion properties of Sc_2−xY_xW₃O₁₂ can be adjusted by the employment of Y dopant; the obtained Sc_1.5Y_0.5W₃O₁₂ ceramic shows almost zero thermal expansion and its average linear thermal expansion coefficient is −0.00683×10⁻⁶ °C⁻¹ in the 25–250 °C range.     

The performances of higher alcohol synthesis over nickel modified K2CO3/MoS2 catalyst

Ni modified K₂CO₃/MoS₂ catalyst was prepared and the performance of higher alcohol synthesis catalyst was investigated under the conditions: T = 280–340 °C, H₂/CO (molar radio) = 2.0, GHSV = 3000 h^− 1, and P = 10.0 MPa. Compared with conventional K₂CO₃/MoS₂ catalyst, Ni/K₂CO₃/MoS₂ catalyst showed higher activity and higher selectivity to C₂⁺OH. The optimum temperature range was 320–340 °C and the maximum space-time yield (STY) of alcohol 0.30 g/ml h was obtained at 320 °C. The selectivity to hydrocarbons over Ni/K₂CO₃/MoS₂ was higher, however, it was close to that of K₂CO₃/MoS₂ catalyst as the temperature increased. The results indicated that nickel was an efficient promoter to improve the activity and selectivity of K₂CO₃/MoS₂ catalyst.     

TiO2-V2O5纳米纤维光催化氧化烟气中的Hg0

对静电纺丝法制备的TiO₂和TiO₂-V₂O₅纳米纤维进行光催化脱除模拟烟气中Hg⁰的研究。对纳米纤维进行了SEM、TEM、XRD、BET和UV-Vis检测。结果表明TiO₂-V₂O₅纳米纤维为锐钛矿,V₂O₅高度分散在TiO₂中。纤维直径在200 nm左右,由粒径为10 nm左右的微粒组成。掺杂V₂O₅后,纤维的吸光范围扩大,在可见光范围内的吸光度比纯TiO₂时有了很大提高。实验研究了不同光照条件、V₂O₅的掺杂量和循环次数对脱汞的影响,分析了TiO₂-V₂O₅催化脱汞的机理。当V₂O₅的质量含量为3%时,TiO₂-V₂O₅在可见光下的脱汞率可达到66%,比纯TiO₂时的7%有了显著提高;纤维的脱汞性能稳定,多次循环后紫外光和可见光下的脱汞率仍分别保持在80%和65%左右。电子的跃迁和电子、空穴的快速分离是TiO₂-V₂O₅在可见光下脱汞率提高的主要原因。     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Binary CuO/Co3O4 nanofibers for ultrafast and amplified electrochemical sensing of fructose

Cobalt oxide-doped copper oxide composite nanofibers (CCNFs) were successfully achieved via electrospinning followed by thermal treatment processes and then exploited as active electrode material for direct enzyme-free fructose detection. The morphology and the structure of as-prepared samples were investigated by X-ray diffraction spectrum (XRD) and scanning electron microscopy (SEM). The electrocatalytic activity of CCNFs films towards fructose oxidation and sensing performances were evaluated by conventional electrochemical techniques. Cyclic voltammetry (CV) and chronoamperometry (I−t) revealed the distinctly enhanced sensing properties towards fructose compared to pure copper oxide nanofibers (CNFs), i.e., showing significantly lowered overpotential of 0.30 V, ultrafast (1 s) and ultrasensitive (18.988 μA mM⁻¹) current response in a wide linear range of 1.0 × 10⁻⁵ M to 6.0 × 10⁻³ M with satisfied reproducibility and stability, which could be ascribed to the synergic catalytic effect of the binary CuO/Co₃O₄ composite nanofibers and the highly porous three-dimensional network films structure of the CCNFs. In addition, a good selectivity for fructose detection was achieved. Results in this work demonstrated that CCNFs is one of the promising catalytic electrode materials for enzymeless fructose sensor fabrication.