Electrochemical properties and hydrogen storage mechanism of perovskite-type oxide LaFeO3 as a negative electrode for Ni/MH batteries

Perovskite-type oxide LaFeO₃ powder was prepared using a stearic acid combustion method. Its phase structure, electrochemical properties and hydrogen storage mechanism as negative electrodes for nickel/metal hydride (Ni/MH) batteries have been investigated systematically. The results of X-ray diffraction (XRD) analysis show that both the calcined powder and the charged/discharged samples after 10 cycles have orthorhombic structures. The discharge capacity, whose maximum value appeared at the first cycle, is 530.3 mA h g⁻¹ at 333 K and increases with an increase in temperature. The discharge capacity decreases distinctly during the first three cycles and then stays steady at about 80 mA h g⁻¹, 160 mA h g⁻¹ and 350 mA h g⁻¹ at 298 K, 313 K and 333 K, respectively. The hydrogen storage mechanism is studied by XRD, X-ray photoelectron spectroscopy (XPS) and mass spectrometry (MS), coupled with pressure-composition-temperature (PCT) methods. Hydrogen atoms may be intercalating into the oxide lattice and forming a homogeneous solid solution during the charging process.     

Electrochemical properties of La1−xSrxFeO3 (x = 0.2, 0.4) as negative electrode of Ni-MH batteries

La_(1−x)Sr_xFeO₃ (x = 0.2,0.4) powders were prepared by a stearic acid combustion method, and their phase structure and electrochemical properties were investigated systematically. X-ray diffraction (XRD) analysis shows that La_(1−x)Sr_xFeO₃ perovskite-type oxides consist of single-phase orthorhombic structure (x = 0.2) and rhombohedral one (x = 0.4), respectively. The electrochemical test shows that the reaction at La_(1−x)Sr_xFeO₃ oxide electrodes are reversible. The discharge capacities of La_(1−x)Sr_xFeO₃ oxide electrodes increase as the temperature rises. With the increase of the temperature from 298 K to 333 K, their initial discharge capacity mounts up from 324.4 mA h g⁻¹ to 543.0 mA h g⁻¹ (when x = 0.2) and from 147.0 mA h g⁻¹ to 501.5 mA h g⁻¹ (when x = 0.4) at the current density of 31.25 mA g⁻¹, respectively. After 20 charge-discharge cycles, they still remain perovskite-type structure. Being similar to the relationship between the discharge capacity and the temperature, the electrochemical kinetic analysis indicates that the exchange current density and proton diffusion coefficient of La_(1−x)Sr_xFeO₃ oxide electrodes increase with the increase of the temperature. Compared with La_0.8Sr_0.2FeO₃, La_0.6Sr_0.4FeO₃ electrode is a more promising candidate for electrochemical hydrogen storage because of its higher cycle capacity at various temperatures.     

Hydrothermal synthesis of flower-like Zn2SnO4 composites and their performance as anode materials for lithium-ion batteries

Flower-like Zn₂SnO₄ composites had been prepared through a green hydrothermal synthesis. The structural, morphological and electrochemical properties were investigated by means of XRD, BET, SEM, TEM, and electrochemical measurement. The results show that the as-prepared sample is in high purity phase and of good crystallinity; meanwhile it has a particular 3-D structure and large surface area. Electrochemical measurement suggests that flower-like Zn₂SnO₄ composites exhibit better cycling properties and lower initial irreversible capacities than the solid Zn₂SnO₄ cubes. The first discharge and charge capacities of the material are 1750 mA h g⁻¹ and 880 mA h g⁻¹ respectively. A higher reversible capacity of 501 mA h g⁻¹ was obtained after 50 cycles at a current density of 300 mA g⁻¹. The higher reversible capacity and good stability can be related to the special nanostructural features of the material. Such Zn₂SnO₄ structures synthesized by the simple and cheap method are expected to have potential application in energy storage.     

Study of the electrochemical hydrogen storage properties of the proton-conductive perovskite-type oxide LaCrO3 as negative electrode for Ni/MH batteries

LaCrO₃ was prepared by glycine combustion method and investigated as negative electrode for Ni/MH batteries. The structures of the as-calcined powder and the 20th charge-discharge cycle sample were characterized by XRD. The electrochemical experimental results demonstrated that the LaCrO₃ electrode showed excellent electrochemical reversibility and considerably high charge-discharge capacity at various temperatures. Except for the charge-discharge cycle at 298 K, the discharge capacities of LaCrO₃ electrode keep steady at 107.1 mA h g⁻¹and 285 mA h g⁻¹ at 313 K and 333 K after 5 cycles, respectively.     

Porous polythiophene as a cathode material for lithium batteries with high capacity and good cycling stability

Polythiophene (PTh) has been synthesized by chemical oxidative polymerization and used as an active cathode material in lithium batteries. The lithium batteries are characterized by cyclic voltammetry (CV), galvanostatic charge/discharge cycling and electrochemical impedance spectroscopic studies (EIS). The lithium battery with the PTh cathode exhibits a discharge voltage of 3.7 V compared to Li⁺/Li and excellent electrochemical performance. PTh can provide large discharge capacities above 50 mA h g⁻¹ and good cycle stability at a high current density 900 mA g⁻¹. After 500 cycles, the discharge capacity is maintained at 50.6 mA h g⁻¹. PTh is a promising candidate for high-voltage power sources with excellent electrochemical performance.     

Synthesis of sawtooth-like Li4Ti5O12 nanosheets as anode materials for Li-ion batteries

Hierarchical layered hydrous lithium titanate and Li₄Ti₅O₁₂ microspheres assembled by nanosheets have been successfully synthesized via a hydrothermal process and subsequent thermal treatment. The electrochemical properties of the two samples have been investigated by galvanostatic methods. The former, with the obvious layered structure and a large surface area, delivers a reversible capacity of 180 mA h g⁻¹ after 200 cycles at 200 mA g⁻¹. As for Li₄Ti₅O₁₂, with the intriguing and unique sawtooth-like morphology, it presents exceptional high rate performance and excellent cycling stability. Up to 132 mA h g⁻¹ is obtained after 200 cycles at 10,000 mA g⁻¹ (57 C), proving itself promising for high-rate applications.     

Synthesis and characterization of high-density LiFePO4/C composites as cathode materials for lithium-ion batteries

To achieve a high-energy-density lithium electrode, high-density LiFePO₄/C composite cathode material for a lithium-ion battery was synthesized using self-produced high-density FePO₄ as a precursor, glucose as a C source, and Li₂CO₃ as a Li source, in a pipe furnace under an atmosphere of 5% H₂-95% N₂. The structure of the synthesized material was analyzed and characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical properties of the synthesized LiFePO₄/carbon composite were investigated by cyclic voltammetry (CV) and the charge/discharge process. The tap-density of the synthesized LiFePO₄/carbon composite powder with a carbon content of 7% reached 1.80 g m⁻³. The charge/discharge tests show that the cathode material has initial charge/discharge capacities of 190.5 and 167.0 mAh g⁻¹, respectively, with a volume capacity of 300.6 mAh cm⁻³, at a 0.1C rate. At a rate of 5C, the LiFePO₄/carbon composite shows a high discharge capacity of 98.3 mAh g⁻¹ and a volume capacity of 176.94 mAh cm⁻³.     

Electrodeposited PbO2 thin film as positive electrode in PbO2/AC hybrid capacitor

Lead dioxide (PbO₂) thin films were prepared on Ti/SnO₂ substrates by means of electrodeposition method. Galvanostatic technique was applied in PbO₂ film formation process, and the effect of deposition current on morphology and crystalline form of the PbO₂ thin films was studied by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The energy storage capacity of the prepared PbO₂ electrode was investigated by means of cyclic voltammetry (CV) and charge/discharge cycles, and a rough surface structure PbO₂ film was selected as positive electrode in the construction of PbO₂/AC hybrid capacitor in a 1.28 g cm⁻³ H₂SO₄ solution. The electrochemical performance was determined by charge/discharge tests and electrochemical impedance spectroscopy (EIS). The results showed that the PbO₂/AC hybrid capacitor exhibited high capacitance, good cycling stability and long cycle life. In the voltage range of 1.8-0.8 V during discharge process, considering the weight of all components of the hybrid capacitor, including the two electrodes, current collectors, H₂SO₄ electrolyte and separator, the specific energy and power of the device were 11.7 Wh kg⁻¹ and 22 W kg⁻¹ at 0.75 mA cm⁻², and 7.8 Wh kg⁻¹ and 258 W kg⁻¹ at 10 mA cm⁻² discharge currents, respectively. The capacity retains 83% of its initial value after 3000 deep cycles at the 4 C rate of charge/discharge.     

Facile preparation and good electrochemical hydrogen storage properties of chain-like and rod-like Co-B nanomaterials

Chain-like and rod-like Co-B nanomaterials are prepared by chemical reduction method in cetyltrimethylammonium bromide (CTAB) and polyvinylpyrrolidone (PVP) aqueous solution, respectively. XRD patterns demonstrate that the two materials both have amorphous structures. SEM and TEM images show that the chain-like Co-B constructs of one-by-one tactic ball-like particles with nanoflakes on the surface, whereas the rod-like Co-B alloy possesses a porous nanostructure. The results of electrochemical measurements indicate that, as negative electrode materials of Ni-MH batteries, their electrochemical properties are both better than those of regular Co-B alloy. At the discharge current density 25 mA g⁻¹, the discharge capacities of the chain-like and the rod-like Co-B alloys are 314 mAh g⁻¹ and 292 mAh g⁻¹ after 50 cycles, respectively, which are both higher than that of regular Co-B alloy. XRD patterns of the electrodes on different charge-discharge states illustrate that the discharge capacity is attributed to hydrogenation of Co-B alloy.     

Influence of carbon sources on LiFePO4/C composites synthesized by the high-temperature high-energy ball milling method

Carbon-coated LiFePO₄ composites were synthesized by a new method of high-temperature high-energy ball milling (HTHEBM). Fe₂O₃ and LiH₂PO₄ were used as raw materials. Glucose, sucrose, citric acid and active carbon were used as reducing agents and carbon sources, respectively. In this method, high-energy ball milling and carbon coating worked together and, therefore, fine and homogeneous LiFePO₄/C particles with excellent properties were obtained in a relatively short synthesis time of 9 h. Moreover, the synthesis process could be completely finished at a relatively lower temperature of 600 °C for high-energy ball milling transforming mechanical energy into thermal energy. The results of X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical performance tests indicated that carbon source had an important influence on the properties of LiFePO₄/C composites synthesized by the HTHEBM method. It was proved that the LiFePO₄ composites coated with glucose had the best properties with 1 μm geometric mean diameter and 150.3 mA h g⁻¹ initial discharge capacity at a current rate of 0.1 C. After the 20th cycle test, the reversible capacity was 148 mA h g⁻¹ at 0.1 C, showing a retention ratio to the initial capacity of 98.5%.     

Synthesis, characterization and electrochemical performance of mesoporous FePO4 as cathode material for rechargeable lithium batteries

Mesoporous FePO₄ could deliver enhanced specific capacity of 160 mAh g⁻¹ at first discharge process, 90% of theoretical capacity of pure FePO₄, and 135 mAh g⁻¹ in the following cycles at 0.1 C rate. At 1 and 3 C rates, the capacities are 110 and 85 mAh g⁻¹, respectively, which is much higher than that of previously reported for modified FePO₄ materials. Electrochemical impedance spectroscopy (EIS) tests proved that mesoporous structure in FePO₄ materials enhanced the lithium ion intercalation/deintercalation kinetics as indicated by smaller charge transfer resistance (R_ct) of these materials. These results revealed that this mesoporous electrode material can be a potential candidate for high-power energy conversion devices.     

Comparison of 4 V and 3 V electrochemical properties of nanocrystalline LiMn2O4 cathode particles in lithium ion batteries prepared by ultrasonic spray pyrolysis

Nanocrystalline LiMn₂O₄ particles were prepared by an ultrasonic spray pyrolysis method using nitrate salts at 800 °C in air atmosphere. Particle properties were characterized by the X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy. In addition, cyclic voltammetry and galvanostatic tests were performed to investigate the effects of structure on electrochemical behavior of both the 4 V and 3 V potential plateaus. Particle characterization studies show that the nanocrystalline particles have spinel structure of submicron size with spherical morphology. Particles, ranging between 75 and 1250 nm, were formed by aggregation of nanoparticles. Discharge capacity of LiMn₂O₄ particles between 3.0 and 4.5 V is 70 mA h g⁻¹ and cumulative capacity between 2.2 and 4.5 V is 111 mA h g⁻¹ at 0.5 C rate. Discharge capacity at the 4 V potential region reduces to 47% of initial capacity, whereas cumulative capacity fade is 62% after 100 cycles at 0.5 C rate. Although nanocrystalline LiMn₂O₄ cathode particles exhibit good rate capability at the 4 V plateau, capacity decreased rapidly by increasing C- rates and cycling between 2.2 and 4.5 V. The loss of capacity can be attributed to phase transformation and dissolution of electrode material. Particle characterization of used cathodes showed that nanocrystalline LiMn₂O₄ electrodes partly dissolve during electrochemical cycling.     

Performance evaluation of CNT/polypyrrole/MnO2 composite electrodes for electrochemical capacitors

A ternary composite of CNT/polypyrrole/hydrous MnO₂ is prepared by in situ chemical method and its electrochemical performance is evaluated by using cyclic voltammetry (CV), impedance measurement and constant-current charge/discharge cycling techniques. For comparative purpose, binary composites such as CNT/hydrous MnO₂ and polypyrrole/hydrous MnO₂ are prepared and also investigated for their physical and electrochemical performances. The specific capacitance (SC) values of the ternary composite, CNT/hydrous MnO₂ and polypyrrole/hydrous MnO₂ binary composites estimated by CV technique in 1.0 M Na₂SO₄ electrolyte are 281, 150 and 35 F g⁻¹ at 20 mV s⁻¹ and 209, 75 and 7 F g⁻¹ at 200 mV s⁻¹, respectively. The electrochemical stability of ternary composite electrode is investigated by switching the electrode back and forth for 10,000 times between 0.1 and 0.9 V versus Ag/AgCl at 100 mV s⁻¹. The electrode exhibits good cycling stability, retaining up to 88% of its initial charge at 10,000th cycle. A full cell assembled with the ternary composite electrodes shows a SC value of 149 F g⁻¹ at a current loading of 1.0 mA cm⁻² during initial cycling, which decreased drastically to a value of 35 F g⁻¹ at 2000th cycle. Analytical techniques such as scanning electron microscopy (SEM), X-ray diffraction spectroscopy (XRD), Brunauer-Emmet-Teller (BET) surface area measurement and inductively coupled plasma-atomic emission spectrometry (ICP-AES) are also used to characterize the composite materials.     

TiO2 nanotubes manufactured by anodization of Ti thin films for on-chip Li-ion 2D microbatteries

The use of self-organized TiO₂ nanotube arrays electrochemically grown onto Si is investigated for the fabrication of an alternative electrode dedicated to on-chip Li-ion 2D microbatteries. Discharge/charge curves and cycling performance are studied in lithium-anode electrochemical test cells for both amorphous and crystalline titania nanotubes. At 5 μA cm⁻² amorphous TiO₂ nanotube layers onto Si deliver a maximum areal capacity of 89 μAh cm⁻² in the first reversible discharge and 56 μAh cm⁻² over 50 cycles. We demonstrate that these nanostructured thin film electrodes showing such electrochemical performances are compatible with IC technology.     

Performance of electrochemically generated Li21Si5 phase for lithium-ion batteries

The nature of Li-Si alloy phases that are generated in electrochemical lithiation is examined as a function of temperature. The electrochemical lithiation is performed at 0.0 V (vs. Li/Li⁺) by short-circuiting an amorphous Si thin-film electrode with a Li metal counter electrode. At 25-85 °C, the well-known Li₁₅Si₄ phase (theoretical specific capacity = 3580 mA h g⁻¹) forms. At 100-120 °C, however, Li₂₁Si₅ (4008 mA h g⁻¹) that is known to be the most Li-rich phase in Li-Si system is generated. The crystallization into Li₂₁Si₅ is, however, so kinetically slow that it does not appear in the transient cycling experiment. The Li₂₁Si₅ phase is converted to amorphous Si upon de-lithiation, but the restoration back to the initial phase is only observed at 100-120 °C after a prolonged lithiation at 0.0 V. The cycleability of this phase is poor due to a successive Li trapping inside the Si matrix, which is caused by the formation of electrically isolated Si islands.     

Polyaniline as cathodic material for electrochemical energy sources: The role of morphology

Polyaniline layers of different morphologies ranging from open and “sponge-like” structures to compact and “pebble-like” surfaces were synthesized from perchlorate solutions and employed as cathode in the galvanic cell with Zn anode and NH₄Cl/ZnCl₂ electrolyte. Cathodic properties of synthesized layers were investigated by the constant current charging/discharging method in 500 cycles. Specific charge capacities and specific energies obtained form the current-time curves strongly depend on the morphology of investigated layers and discharge conditions. The results unambiguously show that charging/discharging reaction of polyaniline layers is limited to relatively thin layer at polymer/solution boundary. Specific charge capacities are inversely related to both the polymer thickness and the discharge current density. In the limit of zero current densities the specific charge capacity as high as 245 A h kg⁻¹ could be achieved for porous structures of polyaniline layers. Specific capacitance higher than 400 F g⁻¹ obtained at 2 mA cm⁻² current density makes polyaniline a promising material for the application in electrochemical supercapacitors. The electrochemical behaviour of the layers was investigated by cyclic voltammetry and electrochemical impedance spectroscopy before and after 500 cycles of charging/discharging experiments. Both, cyclic voltammetry and electrochemical impedance spectroscopy showed that some polyaniline layers develop an increased charged transfer resistance at the carbon support/polymer interface during charging/discharging process. The increased charge transfer resistance does not affect the overall specific charge of the layers. The low-frequency capacities in impedance spectra are attributed to charging/discharging of polymer/electrolyte interface and seem to be related to the specific charge capacities obtained by extrapolation to zero current density discharge reaction.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Hydrothermal synthesis of layered Li[Ni1/3Co1/3Mn1/3]O2 as positive electrode material for lithium secondary battery

In attempts to prepare layered Li[Ni_1/3Co_1/3Mn_1/3]O₂, hydrothermal method was employed. The hydrothermal precursor, [Ni_1/3Co_1/3Mn_1/3](OH)₂, was synthesized via a coprecipitation route. The sphere-shaped powder precursor was hydrothermally reacted with LiOH aqueous solution at 170 °C for 4 days in autoclave. From X-ray diffraction and scanning electron microscopic studies, it was found that the as-hydrothermally prepared powders were crystallized to layered α-NaFeO₂ structure and the particles had spherical shape. The as-prepared Li[Ni_1/3Co_1/3Mn_1/3]O₂ delivered an initial discharge of about 110 mA h g⁻¹ due to lower crystallinity. Heat treatment of the hydrothermal product at 800 °C was significantly effective to improve the structural integrity, which consequently affected the increase in the discharge capacity to 157 (4.3 V cut-off) and 182 mA h g⁻¹ (4.6 V cut-off) at 25 °C with good reversibility.     

Preparation and characterization of three dimensionally ordered macroporous Li4Ti5O12 anode for lithium batteries

Three dimensionally ordered macroporous (3DOM) Li₄Ti₅O₁₂ membrane (80 μm thick) was prepared by a colloidal crystal templating process. Colloidal crystal consisting of monodisperse polystyrene particles (1 μm diameter) was used as the template for the preparation of macroporous Li₄Ti₅O₁₂. A precursor sol consisting of titanium isopropoxide and lithium acetate was impregnated into the void space of template, and it was calcined at various temperatures. A macroporous membrane of Li₄Ti₅O₁₂ with inverse-opal structure was successfully prepared at 800 °C. The interconnected pores with uniform size (0.8 μm) were clearly observed on the entire part of membrane. The electrochemical properties of the three dimensionally ordered Li₄Ti₅O₁₂ were characterized with cyclic voltammetry and galvanostatic charge and discharge in an organic electrolyte containing a lithium salt. The 3DOM Li₄Ti₅O₁₂ exhibited a discharge capacity of 160 mA h g⁻¹ at the electrode potential of 1.55 V versus Li/Li⁺ due to the solid state redox of Ti^3+/4+ accompanying with Li⁺ ion insertion and extraction. The discharge capacity was close to the theoretical capacity (167 mA h g⁻¹), which suggested that the Li⁺ ion insertion and extraction took place at the entire part of 3DOM Li₄Ti₅O₁₂ membrane. The 3DOM Li₄Ti₅O₁₂ electrode showed good cycle stability.     

Large reversible capacity of high quality graphene sheets as an anode material for lithium-ion batteries

High quality graphene sheets were prepared from graphite powder through oxidation followed by rapid thermal expansion in nitrogen atmosphere. The preparation process was systematically investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy and Brunauer-Emmett-Teller (BET) measurements. The morphology and structure of graphene sheets were characterized by scanning electron microscope (SEM) and high-resolution transmission electron microscopy (HRTEM). The electrochemical performances were evaluated in coin-type cells versus metallic lithium. It is found that the graphene sheets possess a curled morphology consisting of a thin wrinkled paper-like structure, fewer layers (∼4 layers) and large specific surface area (492.5 m² g⁻¹). The first reversible specific capacity of the prepared graphene sheets was as high as 1264 mA h g⁻¹ at a current density of 100 mA g⁻¹. Even at a high current density of 500 mA g⁻¹, the reversible specific capacity remained at 718 mA h g⁻¹. After 40 cycles, the reversible capacity was still kept at 848 mA h g⁻¹ at the current density of 100 mA g⁻¹. These results indicate that the prepared high quality graphene sheets possess excellent electrochemical performances for lithium storage.