背照式GaN/AlGaN p-i-n紫外探测器的制备与性能

文章研究了p-GaN/i-GaN/n-A l0.3Ga0.7N异质结背照式p-i-n可见盲紫外探测器的制备与性能。器件的响应区域为310~365nm,最大响应率为0.046A/W,对应的内量子效率为19%,优值因子R0A达到1.77×108Ω.cm2,相应的在363nm处的探测率D*=2.6×1012cmHz1/2W-1。     

Pt/CdS Schottky紫外探测器的光电性能研究

制备了Pt/CdS Schottky紫外探测器,对Pt/CdS Schottky紫外芯片对中波红外(3~5μm)的透过率进行了研究,并对器件光电性能进行了测试分析。通过优化Pt电极制备条件及对SiO2增透膜的研究,使Pt/CdS Schottky紫外芯片对中波红外波段的透过率达到85%。室温300 K下,所制备Pt/CdS Schottky紫外探测器在零偏压处的背景光电流为-0.063 nA,在+6 V时的暗电流密度为7.6×10-7 A/cm2,R0A达到7.2×104Ω·cm2,其50%截止波长为510 nm。     

Extended-wavelength 640 × 1 linear InGaAs detector arrays using N-on-P configuration for back illumination

在N-on-P型In0.78Al0.22As/In0.78Ga0.22As外延材料上,采用感应耦合等离子体(ICP)刻蚀技术制备了背照射640×1线列InGaAs探测器芯片,研究了探测器光电性能.结果表明,室温下单元器件响应截止波长和峰值波长分别为2.36 μm和1.92 μm,平均优值因子(R0A)为16.0Ω·cm2,峰值量子效率达到了37.5％;在1 ms积分时间下焦平面探测器平均峰值探测率达到了2.01×1011 cmHz1/2/W,响应非均匀性为8.77％,盲元率约为0.6％.     

高性能背照式GaN/AlGaN p-i-n紫外探测器的制备与性能

研究了GaN/AlGaN异质结背照式P-i-n结构可见盲紫外探测器的制备与性能.GaN/MGaN外延材料采用金属有机化学气相沉积(MOCVD)方法生长,衬底为双面抛光的蓝宝石,缓冲层为AiN,n型层采用厚度为0.8 μm的Si掺杂Al0.3Ga0.7形成窗口层,i型层为0.18 μm的非故意掺杂的GaN,P型层为0.15 μm的Mg掺杂GaN.采用C12、Ar和BCl3感应耦合等离子体刻蚀定义台面,光敏面面积为1.96×10-3cm2.可见盲紫外探测器展示了窄的紫外响应波段,响应区域为310-365 nm,在360 nm处响应率最大,为0.21 A/W,在考虑表面反射时,内量子效率达到82%;优质因子R0A为2.00×108 Ω·cm2,对应的探测率D*=2.31×1013·Hz1/2·W-1;且零偏压下的暗电流为5.20×10-13A.     

基于N-on-P结构的背照射延伸波长640×1线列InGaAs探测器

在N-on-P型In0.78Al0.22As/In0.78Ga0.22As外延材料上,采用感应耦合等离子体(ICP)刻蚀技术制备了背照射640×1线列InGaAs探测器芯片,研究了探测器光电性能.结果表明,室温下单元器件响应截止波长和峰值波长分别为2.36μm和1.92μm,平均优值因子(R0A)为16.0Ω.cm2,峰值量子效率达到了37.5%;在1 ms积分时间下焦平面探测器平均峰值探测率达到了2.01×1011 cmHz1/2/W,响应非均匀性为8.77%,盲元率约为0.6%.     

背照式InGaN紫外探测器的制备与数值模拟

研究了背照式InGaN p-i-n结构的紫外探测器的制备与数值模拟.通过低压金属有机化学气相沉积(MOCVD)方法生长p-GaN/i-InGaN/n-GaN外延片,采用标准的Ⅲ-Ⅴ族器件制备工艺,成功制备出p-i-n结构的InGaN紫外探测器.探测器台面半径为30 μm,在-5V偏压下暗电流为-6.47×10 1 2 A,对应的电流密度为2.29×10-7 A/cm2.该探测器响应波段为360～380 nm,在371 nm处达到峰值响应率为0.21 A/W,对应的外量子效率为70％,内量子效率为78.4％.零偏压下,优值因子R0A=5.66×107 Ω·cm2,对应的探测率D* =2.34×1013 cm·Hz1/2·W-1.同时,利用Silvaco TCAD软件进行数值模拟,响应率曲线仿真值与实验值拟合较好.     

热电制冷HgCdTe中波红外探测器的研制

利用碲镉汞(HgCdTe)体晶材料,采用HgCdTe材料拼接技术、磨抛技术等成熟的探测器芯片制备工艺以及三级热电制冷技术,设计并研制出了热电制冷型13元HgCdTe中波红外光导探测器。在-50℃时,峰值电压响应率可达2.7×104 V/W,峰值探测率达到2.3×1010 cm·Hz1/2·W-1,响应波段在3.0~4.6mm之间,峰值响应波长为4.2mm。     

高性能石墨烯/硅纳米线阵列异质结光探测器

设计了基于石墨烯/硅纳米线阵列异质结的高灵敏度自驱动光探测器。该探测器中的纳米线阵列为直径约为100 nm的周期性结构,表面纳米结构的光捕获效应可以有效地抑制入射光的反射,增加了有效光照面积,增强了异质结的吸收,从而提高了器件的光电检测性能。实验制备出的异质结在±3 V偏压下表现出明显的电流整流特性,整流比为6.93×10⁵。此外,由于纳米线阵列的光捕获效应增强了探测器在紫外到近红外的吸收,所以该探测器的探测范围可以从紫外到近红外光。在入射波长810 nm、光强为90μW/cm²的光照下,光探测器的光电流响应度可以达到0.56 A·W^-1,光电压响应度达1.24×10⁶ V·W^-1,探测率为1.18×10¹² Jones。更重要的是,该器件具有30/32μs的快速升/降响应速度。     

薄p型层GaN基p-i-n型紫外探测器的反向漏电特性

制备了薄p型层GaN基p-i-n型紫外探测器,并对其反向漏电特性进行了研究。探测器材料采用金属有机化学气相沉积(MOCVD)方法在蓝宝石衬底上外延生长获得,p-GaN的厚度为30nm。基于该材料制作了具有共面电极的探测器器件,并采用SiO2对刻蚀侧壁进行了钝化。测试结果表明,结面积为1.825×10-4cm2的器件在-1V时的反向漏电流面密度为3.0×10-9 A/cm2,优质因子达到3.7×109Ω.cm2。     

283 nm背照射p-i-n型AlGaN日盲紫外探测器

实验中使用在蓝宝石衬底上用低压金属有机化学气相沉积（MOCVD）生长的AlGaN基p-i-n结构材料,通过对工艺流程的优化设计,制作了背照射p-i-n型AlGaN日盲紫外探测器,获得了较高的外量子效率。材料中p区和i区的Al组分为40%,n区Al组分为65%。探测器为直径500 m的圆形,光谱响应起止波长为260~310 nm,峰值响应波长283 nm。零偏压下,暗电流密度为2.710-10 Acm-2,对应的R0A参数为3.8108 cm2,峰值响应率为13 mA/W,对应的峰值探测率为1.971012 cmHz1/2W-1。其在-7 V偏压下,峰值响应率达到148 mA/W,对应的外量子效率达到63%。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first