Improved hydrogen sorption performance of NbF5-catalysed NaAlH4

The effect of NbF₅ on the hydrogen sorption performance of NaAlH₄ has been investigated. It was found that the dehydrogenation/hydrogenation properties of NaAlH₄ were significantly enhanced by mechanically milling with 3 mol% NbF₅. Differential scanning calorimetry results indicate that the ball-milled NaAlH₄-0.03NbF₅ sample lowered the completion temperature for the first two steps dehydrogenation by 71 °C compared to the pristine NaAlH₄ sample. Isothermal hydrogen sorption measurements also revealed a significant enhancement in terms of the sorption rate and capacity, in particular, at reduced operation temperatures. The apparent activation energy for the first-step and the second-step dehydrogenation of the NaAlH₄-0.03NbF₅ sample is estimated to be 88.2 kJ/mol and 102.9 kJ/mol, respectively, by using Kissinger’s approach, which is much lower than for pristine NaAlH₄, indicating the reduced kinetic barrier. The rehydrogenation kinetics of NaAlH₄ was also improved with 3 mol% NbF₅ doping, absorbing ∼1.7 wt% hydrogen at 150 °C for 2 h under ∼5.5 MPa hydrogen pressure. In contrast, no hydrogen was absorbed by the pristine NaAlH₄ sample under the same conditions. The formation of Na₃AlH₆ was detected by X-ray diffraction on the rehydrogenated NaAlH₄-0.03NbF₅ sample. Furthermore, the structural changes in the NbF₅-doped NaAlH₄ sample after ball milling and the hydrogen sorption were carefully examined, and the active species and mechanism of catalysis in NbF₅-doped NaAlH₄ are discussed.     

Multi-hydride systems with enhanced hydrogen storage properties derived from Mg(BH4)2 and LiAlH4

A two-step ball-milling method has been provided to synthesize Mg(BH₄)₂ using NaBH₄ and MgCl₂ as starting materials. The method offers high yield and high purity (96%) of the compound. The as-synthesized Mg(BH₄)₂ is then combined with LiAlH₄ by ball-milling in order to form new multi-hydride systems with high hydrogen storage properties. The structure, the dehydrogenation and the reversibility of the combined systems are studied. Analyses show that a metathesis reaction takes place between Mg(BH₄)₂ and LiAlH₄ during milling, forming Mg(AlH₄)₂ and LiBH₄. Mg(BH₄)₂ is excessive and remains in the ball-milled product when the molar ratio of Mg(BH₄)₂ to LiAlH₄ is over 0.5. The onset dehydrogenation temperature of the combined systems is lowered to ca. 120 °C, which is much lower than that of either Mg(BH₄)₂ or LiAlH₄. The dehydrogenation capacities of the combined systems below 300 °C are all higher than that of both Mg(BH₄)₂ and LiAlH₄. The combined systems are reversible for hydrogen storage at moderate hydrogenation condition, and rapid hydrogenation occurred within the initial 30 min. Moreover, the remained Mg(BH₄)₂ in the combined systems is found also partially reversible. The mechanism of the enhancement of the hydrogen storage properties and the dehydrogenation/hydrogenation process of the combined systems were discussed.     

Reversible hydrogen storage in LiBH4/Ca(AlH4)2 systems

To improve the hydrogen storage property of LiBH₄, the LiBH₄/Ca(AlH₄)₂ reactive systems with various ratios were constructed, and their de-/hydrogenation properties as well as the reaction mechanisms were investigated experimentally. It was found that the sample with the LiBH₄ to Ca(AlH₄)₂ molar ratio of 6:1 exhibits the best comprehensive hydrogen storage properties, desorbing hydrogen completely (8.2 wt.%) within 35 min at 450 °C and reversibly absorbing 4.5 wt.% of hydrogen at 450 °C under a hydrogen pressure as low as 4.0 MPa. During the first dehydrogenation process of the LiBH₄/Ca(AlH₄)₂ systems, the CaH₂ and Al particles were in situ precipitated via the self-decomposition of Ca(AlH₄)₂, and then reacted with LiBH₄ to form CaB₆, AlB₂ and LiH. Whereafter, the sample can cycle between LiBH₄ + Ca(BH₄)₂ + Al in the hydrogenated state and CaB₆ + AlB₂ + LiH in the dehydrogenated state.     

Significantly improved dehydrogenation of LiAlH4 destabilized by K2TiF6

The effects of K₂TiF₆ on the dehydrogenation properties of LiAlH₄ were investigated by solid-state ball milling. The onset decomposition temperature of 0.8 mol% K₂TiF₆ doped LiAlH₄ is as low as 65 °C that 85 °C lower than that of pristine LiAlH₄. Isothermal dehydrogenation properties of the doped LiAlH₄ were studied by PCT (pressure–composition–temperature). The results show that, for the 0.8 mol% K₂TiF₆ doped LiAlH₄ that dehydrogenated at 90 °C, 4.4 wt% and 6.0 wt% of hydrogen can be released in 60 min and 300 min, respectively. When temperature was increased to 120 °C, the doped LiAlH₄ can finish its first two dehydrogenation steps in 170 min. DSC results show that the apparent activation energy (E_a) for the first two dehydrogenation steps of LiAlH₄ are both reduced, and XRD results suggest that TiH₂, Al₃Ti, LiF and KH are in situ formed, which are responsible for the improved dehydrogenation properties of LiAlH₄.     

Enhanced hydrogen desorption from the Co-catalyzed LiBH4–Mg(BH4)2 eutectic composite

Co-based catalyst can significantly improve the dehydrogenation kinetics of the eutectic composite of LiBH₄–Mg(BH₄)₂ (1/1 M ratio). The onset hydrogen desorption temperature of the composite is at about 155 °C, which is ca. 245, 110 or 27 °C lower than that of LiBH₄, Mg(BH₄)₂ or pristine LiBH₄–Mg(BH₄)₂, respectively. Upon holding the samples at 270 °C, the Co catalyzed composite can release hydrogen at a rate 1.6 times faster than that of the pristine one. Electron Paramagnetic Resonance (EPR) characterization evidenced that Co was in a reduced state of Co⁺ which may serve as the functional species in catalyzing the dehydrogenation of the composite.     

Destabilization effects of Mg(AlH4)2 on MgH2: Improved desorption performances and its reaction mechanism

Both kinetics and thermodynamics properties of MgH₂ are significantly improved by the addition of Mg(AlH₄)₂. The as-prepared MgH₂–Mg(AlH₄)₂ composite displays superior hydrogen desorption performances, which starts to desorb hydrogen at 90 °C, and a total amount of 7.76 wt% hydrogen is released during its decomposition. The enthalpy of MgH₂-relevant desorption is 32.3 kJ mol⁻¹ H₂ in the MgH₂–Mg(AlH₄)₂ composite, obviously decreased than that of pure MgH₂. The dehydriding mechanism of MgH₂–Mg(AlH₄)₂ composite is systematically investigated by using x-ray diffraction and differential scanning calorimetry. Firstly, Mg(AlH₄)₂ decomposes and produces active Al^∗. Subsequently, the in-situ formed Al^∗ reacts with MgH₂ and forms Mg–Al alloys. For its reversibility, the products are fully re-hydrogenated into MgH₂ and Al^∗, under 3 MPa H₂ pressure at 300 °C for 5 h.     

Synthesis and hydrogen storage thermodynamics and kinetics of Mg(AlH4)2 submicron rods

Mg(AlH₄)₂ submicron rods with 96.1% purity have been successfully synthesized in a modified mechanochemical reaction process followed by Soxhlet extraction. ∼9.0 wt% of hydrogen is released from the as-prepared Mg(AlH₄)₂ at 125–440 °C through a stepwise reaction. Upon dehydriding, Mg(AlH₄)₂ decomposes first to generate MgH₂ and Al. Subsequently, the newly produced MgH₂ reacts with Al to form a Al_0.9Mg_0.1 solid solution. Finally, further reaction between the Al_0.9Mg_0.1 solid solution and the remaining MgH₂ gives rise to the formation of Al₃Mg₂. The first step dehydrogenation is a diffusion-controlled reaction with an apparent activation energy of ∼123.0 kJ/mol. Therefore, increasing the mobility of the species involved in Mg(AlH₄)₂ will be very helpful for improving its dehydrogenation kinetics.     

Enhancement of the H2 desorption properties of LiAlH4 doping with NiCo2O4 nanorods

Lithium aluminum hydride (LiAlH₄) is considered as an attractive candidate for hydrogen storage owing to its favorable thermodynamics and high hydrogen storage capacity. However, its reaction kinetics and thermodynamics have to be improved for the practical application. In our present work, we have systematically investigated the effect of NiCo₂O₄ (NCO) additive on the dehydrogenation properties and microstructure refinement in LiAlH₄. The dehydrogenation kinetics of LiAlH₄ can be significantly increased with the increase of NiCo₂O₄ content and dehydrogenation temperature. The 2 mol% NiCo₂O₄-doped LiAlH₄ (2% NCO–LiAlH₄) exhibits the superior dehydrogenation performances, which releases 4.95 wt% H₂ at 130 °C and 6.47 wt% H₂ at 150 °C within 150 min. In contrast, the undoped LiAlH₄ sample just releases <1 wt% H₂ after 150 min. About 3.7 wt.% of hydrogen can be released from 2% NCO–LiAlH₄ at 90 °C, where total 7.10 wt% of hydrogen is released at 150 °C. Moreover, 2% NCO–LiAlH₄ displayed remarkably reduced activation energy for the dehydrogenation of LiAlH₄.     

Enhanced dehydrogenation/hydrogenation kinetics of the Mg(NH2)2-2LiH system with NaOH additive

The effects of NaOH addition on hydrogen absorption/desorption properties of the Mg(NH₂)₂-2LiH system were investigated systematically by means of dehydrogenation/hydrogenation measurements and structural analyses. It is found that the NaOH-added Mg(NH₂)₂-2LiH samples exhibit an enhanced dehydrogenation/hydrogenation kinetics. In particular, a ∼36 °C reduction in the peak temperature for dehydrogenation is achieved for the Mg(NH₂)₂-2LiH-0.5NaOH sample with respect to the pristine sample. Structural examinations reveal that NaOH reacts with Mg(NH₂)₂ and LiH to convert to NaH, LiNH₂ and MgO during ball milling. Then, their co-catalytic effects result in a significant improvement in the dehydrogenation/hydrogenation kinetics of the Mg(NH₂)₂-2LiH system. This finding will help in designing and optimizing the novel high-performance catalysts to further improve hydrogen storage in the amide-hydride combined systems.     

Effect of ball milling time on the hydrogen storage properties of TiF3-doped LiAlH4

In the present work, the catalytic effect of TiF₃ on the dehydrogenation properties of LiAlH₄ has been investigated. Decomposition of LiAlH₄ occurs during ball milling in the presence of 4 mol% TiF₃. Different ball milling times have been used, from 0.5 h to 18 h. With ball milling time increasing, the crystallite sizes of LiAlH₄ get smaller (from 69 nm to 43 nm) and the dehydrogenation temperature becomes lower (from 80 °C to 60 °C). Half an hour ball milling makes the initial dehydrogenation temperature of doped LiAlH₄ reduce to 80 °C, which is 70 °C lower than as-received LiAlH₄. About 5.0 wt.% H₂ can be released from TiF₃-doped LiAlH₄ after 18 h ball milling in the range of 60 °C–145 °C (heating rate 2 °C min⁻¹). TiF₃ probably reacts with LiAlH₄ to form the catalyst, TiAl₃. The mechanochemical and thermochemical reactions have been clarified. However, the rehydrogenation of LiAlH₄/Li₃AlH₆ can not be realized under 95 bar H₂ in the presence of TiF₃ because of their thermodynamic properties.     

Effects of Ti-based catalysts and synergistic effect of SWCNTs-TiF3 on hydrogen uptake and release from MgH2

The present investigations are focused on the effect of different Ti-based catalysts (Ti, TiO₂, TiCl₃ and TiF₃) on de/re-hydrogenation characteristics of nanocrystalline MgH₂. Desorption temperature of milled MgH₂ lowers from 380 to 350, 340, 310 and 260 °C with the addition of Ti, TiO_2, TiCl₃ and TiF₃ respectively. The rehydrogenation characteristics are also improved through the deployment of Ti-based catalysts. Among all Ti based additives, TiF₃ is found to be the most effective catalyst for hydrogen sorption from nano MgH₂. The better catalytic effect of TiF₃ over other Ti-based catalyst can be explained on the basis of temperature programmed reduction (TPR) studies. TPR experiments performed for different Ti additives, reveals that there is no oxidation/reduction reaction below 400 °C except for TiF₃. The TPR profile of TiF₃ shows some oxidation/reduction reaction exhibits at 200 °C. In order to further improve the sorption characteristics and cyclability of TiF₃ catalyzed nano MgH₂, we have investigated the effect of SWCNTs in MgH₂+TiF₃ sample. De/rehydrogenation characteristics reveal the synergistic effect of SWCNTs and TiF₃ in MgH₂+TiF₃ sample. The details of the improvement in sorption behavior of MgH₂–TiF₃ in presence of SWCNTs are described and discussed.     

The dehydrogenation performance and reaction mechanisms of Li3AlH6 with TiF3 additive

For Li₃AlH₆ prepared by mechanical milling method, the dissociation reaction enthalpy and activation energy are calculated to be 22.1 kJ mol⁻¹ H₂ and 133.7 ± 2.7 kJ mol⁻¹, respectively. The dehydrogenation performance of Li₃AlH₆ is greatly enhanced by TiF₃ additive, especially in the kinetic behaviors. For the Li₃AlH₆ + 10 mol% TiF₃ sample, the starting temperature of dehydrogenation is obviously decreased by 60 °C from that of pure Li₃AlH₆ (190 °C), and 3.0 wt.% H₂ may be released within 1000 s at 120 °C under an initial vacuum. With the amount of TiF₃ increasing, the starting temperature decreases and the kinetics improves due to the decrease in the activation energy. The X-ray diffraction (XRD) together with thermogravimetric analysis (TGA) results show that there are three mechanochemical reactions involved during milling: i) Li₃AlH₆ + TiF₃ → 3 LiF + Al + Ti + 3H₂, ii) Ti + H₂ → TiH₂, iii) 3 Al + Ti → Al₃Ti. The in-situ formed Ti species (TiH₂ and Al₃Ti) co-catalyze the thermal dehydrogenation of Li₃AlH₆.     

Effects of helical GNF on improving the dehydrogenation behavior of LiMg(AlH4)3 and LiAlH4

The present paper reports the effect of graphitic nanofibres (GNFs) for improving the desorption kinetics of LiMg(AlH₄)₃ and LiAlH₄. LiMg(AlH₄)₃ has been synthesized by mechano-chemical metathesis reaction involving LiAlH₄ and MgCl₂. The enhancement in dehydrogenation characteristics of LiMg(AlH₄)₃ has been shown to be higher when graphitic nanofibres (GNFs) were used as catalyst. Out of two different types of nanofibres namely planar graphitic nanofibre (PGNF) and helical graphitic nanofibre (HGNF), the latter has been found to act as better catalyst. We observed that helical morphology of fibres improves the desorption kinetics and decreases the desorption temperature of both LiMg(AlH₄)₃ and LiAlH₄. The desorption temperature for 8 mol% HGNF admixed LiAlH₄ gets lowered from 159 °C to 128 °C with significantly faster kinetics. In 8 mol% HGNF admixed LiMg(AlH₄)₃ sample, the desorption temperature gets lowered from 105 °C to ∼70 °C. The activation energy calculated for the first step decomposition of LiAlH₄ admixed with 8 mol% HGNF is ∼68 kJ/mol, where as that for pristine LiAlH₄ it is 107 kJ/mol. The activation energy calculated for as synthesized LiMg(AlH₄)₃ is ∼66 kJ/mol. Since the first step decomposition of LiMg(AlH₄)₃ occurs during GNF admixing, the activation energy for initial step decomposition of GNF admixed LiMg(AlH₄)₃ could not be estimated.     

Influence of K2TiF6 additive on the hydrogen sorption properties of MgH2

In this study, the hydrogen storage properties of MgH₂ with the addition of K₂TiF₆ were investigated for the first time. The temperature-programmed desorption results showed that the addition of 10 wt% K₂TiF₆ to the MgH₂ exhibited a lower onset desorption temperature of 245 °C, which was a decrease of about 105 °C and 205 °C compared with the as-milled and as-received MgH₂, respectively. The dehydrogenation and rehydrogenation kinetics of 10 wt% K₂TiF₆-doped MgH₂ were also significantly improved compared to the un-doped MgH₂. The results of the Arrhenius plot showed that the activation energy for the hydrogen desorption of MgH₂ was reduced from 164 kJ/mol to 132 kJ/mol after the addition of 10 wt% K₂TiF₆. Meanwhile, the X-ray diffraction analysis showed the formation of a new phase of potassium hydride and titanium hydride together with magnesium fluoride and titanium in the doped MgH₂ after the dehydrogenation and rehydrogenation process. It is reasonable to conclude that the K₂TiF₆ additive doped with MgH₂ played a catalytic role through the formation of active species of KH, TiH₂, MgF₂ and Ti during the ball milling or heating process. It is therefore proposed that this newly developed product works as a real catalyst for improving the hydrogen sorption properties of MgH₂.     

Improved dehydrogenation of MgH2-Li3AlH6 mixture with TiF3 addition

MgH₂-Li₃AlH₆ mixture shows a mutual activation effect between the components. But the dehydrogenation kinetics is still slow, especially at temperature as low as 250 °C. Hereby, an additive (TiF₃) was introduced into the mixture in the present study. The reaction mechanisms were studied by the combined analyses of X-ray diffraction (XRD), thermogravimetric analysis (TGA), as well as thermodynamic calculations. A two-step ball milling method could reduce the mechanical decomposition of Li₃AlH₆ effectively and was adopted. During milling, Li₃AlH₆ reacts with TiF₃ and produces Al₃Ti while MgH₂ remains stable. All the species are well mixed after milling and the grain size is as small as 100 nm. During TGA test, all the reactions occur at lower temperatures compared with undoped mixture, especially the dehydrogenation of MgH₂, which shows a decrease of 60 °C. Its activation energy is reduced by 32.0 kJ mol⁻¹. The first three isothermal (250 °C) cycles indicate that the kinetics of dehydrogenation has been greatly enhanced, showing a reversible capacity of 4.5 wt.% H₂. The time needed for the 1st dehydrogenation has been shortened to 3600 s from 8000 s for the undoped mixture. These improvements are mainly attributed to the catalytic effect of the in-situ formed Al₃Ti. But there is no influence on the rehydrogenation kinetics and the enthalpy of the dehydrogenation of MgH₂ is unchanged.     

Improved reversible hydrogen storage of LiAlH4 by nano-sized TiH2

Transition metal halides are mostly used as dopants to improve the hydrogen storage properties of LiAlH₄, but they will cause hydrogen capacity loss because of their relatively high molecular weights and reactions with LiAlH₄. To overcome these drawbacks, active nano-sized TiH₂ (TiH₂^nano) prepared by reactive ball milling is used to dope LiAlH₄. It shows superior catalytic effect on the dehydrogenation of LiAlH₄ compared to commercial TiH₂. TiH₂^nano-doped LiAlH₄ starts to release hydrogen at 75 °C, which is 80 °C lower than the onset dehydrogenation temperature of commercial LiAlH₄. About 6.3 wt.% H₂ can be released isothermally at 100 °C (800 min) or at 120 °C (150 min). The apparent activation energies of the first two dehydrogenation reactions of LiAlH₄ are reduced by about 20 and 24 kJ mol⁻¹, respectively. Meanwhile, the regeneration of LiAlH₄ is realized through extracting the solvent from LiAlH₄·4THF, which is obtained by ball milling the dehydrogenated products of TiH₂^nano-doped LiAlH₄ in the presence of THF and 5 MPa H₂. This suggests that TiH₂ is also an effective catalyst for the formation of LiAlH₄·4THF.     

Mechanistic investigations on significantly improved hydrogen storage performance of the Ca(BH4)2-added 2LiNH2/MgH2 system

The hydrogen storage properties and mechanisms of the Ca(BH₄)₂-added 2LiNH₂–MgH₂ system were systematically investigated. The results showed that the addition of Ca(BH₄)₂ pronouncedly improved hydrogen storage properties of the 2LiNH₂–MgH₂ system. The onset temperature for dehydrogenation of the 2LiNH₂–MgH₂–0.3Ca(BH₄)₂ sample is only 80 °C, a ca. 40 °C decline with respect to the pristine sample. Further hydrogenation examination indicated that the dehydrogenated 2LiNH₂–MgH₂–0.1Ca(BH₄)₂ sample could absorb ca. 4.7 wt% of hydrogen at 160 °C and 100 atm while only 0.8 wt% of hydrogen was recharged into the dehydrogenated pristine sample under the same conditions. Structural analyses revealed that during ball milling, a metathesis reaction between Ca(BH₄)₂ and LiNH₂ firstly occurred to convert to Ca(NH₂)₂ and LiBH₄, and then, the newly developed LiBH₄ reacted with LiNH₂ to form Li₄(BH₄)(NH₂)₃. Upon heating, the in situ formed Ca(NH₂)₂ and Li₄(BH₄)(NH₂)₃ work together to significantly decrease the operating temperatures for hydrogen storage in the Ca(BH₄)₂-added 2LiNH₂–MgH₂ system.     

Improved hydrogen storage performance of Mg(NH2)2/LiH mixture by addition of carbon nanostructured materials

The effect of different carbon nanostructures specifically carbon nanotubes (CNTs) and carbon nanofibers (CNFs) on the improvement of the de/re-hydrogenation characteristics of a Mg(NH₂)₂/LiH mixture have been studied. Amongst CNTs and CNFs, the improvement in the hydrogenation properties for the Mg(NH₂)₂/LiH mixture is higher when CNFs are used as a catalyst. Investigations are also focused on the deployment of two different types of CNF (a) CNF1 (synthesized using a ZrFe₂ catalyst) and (b) CNF2 (synthesized using a LaNi₅ catalyst). The results show that CNF2 is better. The maximum decomposition temperature for the pristine Mg(NH₂)₂/LiH mixture is found to be ∼250 °C, which is reduced to ∼180 and ∼150 °C for the sample mixed with 4 wt% of multi-walled carbon nanotubes (MWCNTs) and CNF2 respectively. The activation energy for the dehydrogenation reaction is found to be 74 and 68 kJ mol⁻¹ for the samples mixed with MWCNT and CNF2 respectively, whereas the activation energy for the dehydrogenation reaction of the pristine Mg(NH₂)₂/LiH mixture is 97 kJ mol⁻¹. The catalytic activity and the de/re-hydrogenation characteristics of the Mg(NH₂)₂/LiH mixture mixed with different carbon nanostructures are described and discussed.     

Enhanced hydrogen storage properties of LiBH4 modified by NbF5

In this work, the hydriding–dehydriding properties of the LiBH₄–NbF₅ mixtures were investigated. It was found that the dehydrogenation and reversibility properties of LiBH₄ were significantly improved by NbF₅. Temperature-programed dehydrogenation (TPD) showed that 5LiBH₄–NbF₅ sample started releasing hydrogen from as low as 60 °C, and 4 wt.% hydrogen could be obtained below 255 °C. Meanwhile, ∼7 wt.% H₂ could be reached at 400 °C in 20LiBH₄–NbF₅ sample, whereas pristine LiBH₄ only released ∼0.7 wt.% H₂. In addition, reversibility measurement demonstrated that over 4.4 wt.% H₂ could still be released even during the fifth dehydrogenation in 20LiBH₄–NbF₅ sample. The experimental results suggested that a new borohydride possibly formed during ball milling the LiBH₄–NbF₅ mixtures might be the source of the active effect of NbF₅ on LiBH₄.     

Influence of titanium and nickel dopants on the dehydrogenation properties of Mg(AlH4)2: Electronic structure mechanisms

The structures and dehydrogenation properties of pure and Ti/Ni-doped Mg(AlH₄)₂ were investigated using the first-principles calculations. The dopants mainly affect the geometric and electronic structures of their vicinal AlH₄ units. Ti and Ni dopants improve the dehydrogenation of Mg(AlH₄)₂ in different mechanisms. In the Ti-doped case, Ti prefers to occupy the 13-hedral interstice (Ti_iA) and substitute for the Al atom (Ti_Al), to form a high-coordination structure TiH_n (n = 6, 7). The Ti 3d electrons hybridize markedly with the H 1s electrons in Ti_Al and with the Al 3p electrons in Ti_iA, which weakens the Al–H bond of adjacent AlH₄ units and facilitates the hydrogen dissociation. A TiAl₃H₁₃ intermediate in Ti_iA is inferred as the precursor of Mg(AlH₄)₂ dehydrogenation. In contrast, Ni tends to occupy the octahedral interstice to form the NiH₄ tetrahedron. The tight bind of the Ni with its surrounding H atoms inhibits their dissociation though the nearby Al–H bond also becomes weak. Therefore, Ti is the better dopant candidate than Ni for improving the dehydrogenation properties of Mg(AlH₄)₂ because of its abundant activated hydrogen atoms and low hydrogen removal energy.