Study on photocurrent of bilayers photoanodes using different combination of WO3 and Fe2O3

Bilayer photoanodes were prepared onto glass substrates (FTO) in order to improve generated photocurrents using UV-vis light by water splitting process. A comparative study of photocatalytic was performed over the films surface using Fe₂O_3, WO₃ and mixture of bicomponents (Fe₂O₃:WO₃). Different types of films were prepared using Fe₂O_3, WO₃ and bicomponents (mixture) on FTO substrates. The films were grown by sol gel method with the PEG-300 as the structure-directing agent. The photo-generated of the samples were determined by measuring the currents and voltages under illumination of UV-vis light. The morphology, structure and related composition distribution of the films have been characterized by SEM, XRD and EDX respectively. Photocurrent measurements indicated surface roughness as the effective parameter in this study. The deposited surfaces by bicomponents or mixture are flat without any feature on the surface while the deposited surfaces by WO₃ appears rough surface as small round (egg-shaped particles) and cauliflower-like. The surface deposited by Fe₂O₃ show rough no as well as WO₃ surface. The deposited surfaces by WO₃ reveal the higher value of photocurrent measurement due to surface roughness. Indeed, the roughness can be effective in increasing contact surface area between film and electrolyte and diffuse reflection (light scattering effect). The solution (Fe₂O₃:WO₃) shows the low photocurrent value in compare to WO₃ and Fe₂O₃ hat it may be due to decomposition the compound at 450 ± 1 °C to iron-tungstate Fe₂(WO₄)₃.     

Ag grid induced photocurrent enhancement in WO3 photoanodes and their scale-up performance toward photoelectrochemical H2 generation

The hydrogen generation from photoelectrochemical (PEC) water splitting under visible light was investigated using large area tungsten oxide (WO₃) photoanodes. The photoanodes for PEC hydrogen generation were prepared by screen printing WO₃ films having typical active areas of 0.36, 4.8 and 130 cm² onto the conducting fluorine-doped tin oxide (FTO) substrates with and without embedded inter-connected Ag grid lines. TiO₂ based dye-sensitized solar cell was also fabricated to provide the required external bias to the photoanodes for water splitting. The structural and morphological properties of the WO₃ films were studied before scaling up the area of photoanodes. The screen printed WO₃ film sintered at 500 °C for 30 min crystallized in a monoclinic crystal structure, which is the most useful phase for water splitting. Such WO₃ film revealed nanocrystalline and porous morphology with grain size of ∼70-90 nm. WO₃ photoanode coated on Ag grid embedded FTO substrate exhibited almost two-fold degree of photocurrent density enhancement than that on bare FTO substrate under 1 SUN illumination in 0.5 M H₂SO₄ electrolyte. With such enhancement, the calculated solar-to-hydrogen conversion efficiencies under 1 SUN were 3.24% and ∼2% at 1.23 V for small (0.36 cm²) and large (4.8 cm²) area WO₃ photoanodes, respectively. The rate of hydrogen generation for large area photoanode (130.56 cm²) was 3 mL/min.     

Modeling the optical properties of WO3 and WO3-SiO2 thin films

The optical properties and surface morphology of sol-gel spin coated WO₃ and WO₃-SiO₂ composite films annealed at 250 and are investigated. For the purpose of extracting the optical parameters of the films, a novel form for the dielectric function is introduced, consisting of two Tauc-Lorentz oscillators and an Urbach tail component, which is suited for amorphous multi-transition materials with substantial subgap absorption. The evolution of the refractive indices, transmittances, and band gaps with doping is marked by sizable shifts at 2.0-2.5% SiO₂ doping for the films, and 4.0-4.5% doping for the films. In addition, pronounced changes in the surface roughness of the films occur at these doping values.     

Enhancement of photoelectrochemical response by Au modified in TiO2 nanorods

We report on the design and synthesis of a novel Au/TiO₂/Au heterostructure and its implementation as a photoanode for photoelectrochemical (PEC) application. The Au/TiO₂/Au heterostructure was produced by assembling Au nanoparticles and TiO₂ nanorods (NRs) onto FTO substrate, followed by electrodepositing Au nanoparticles on the TiO₂NRs. Field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and electrochemical methods were adopted to characterize the prepared photoanodes. Compared to the system involving Au nanoparticles directly linked to TiO₂, this Au/TiO₂/Au heterostructure exhibits significant improved photoresponse as a photoanode, as demonstrated good performance in PECs. This study illustrates the importance of pre-deposited Au underlayers in influencing PEC properties of hybrid assembled nanostructures. As the Au/TiO₂NRs/Au photoanodes are easily fabricated and highly stable, Au/TiO₂NRs/Au can serve as a good substitution for TiO₂ in a variety of solar energy driven applications including PEC water splitting, photocatalysis, and solar cells.     

Single-step fabrication of phase-controllable nanocrystalline TiO2 films for enhanced photoelectrochemical water splitting and dye-sensitized solar cells

We introduce a single-step procedure for growing a phase-controllable bilayer-structured TiO₂ film directly onto transparent conductive oxide glass by precipitation from hydrolysis of TiCl₄ in acid solution containing sulfate ions. The obtained bilayer-structured film with anatase nanoparticles in the inner layer which provide high surface area, and an outer layer of larger rutile particles for incident light scattering. In both the water splitting and the dye-sensitized solar cells under AM 1.5 simulated solar light, the bilayer-structured film outperformed the single layer-structured films with either anatase or rutile TiO₂ alone by at least 50%.     

Cathodic shift and improved photocurrent performance of cost-effective Fe2O3 photoanodes

We successfully fabricated cost-effective and efficient pulse electrodeposited Fe₂O₃ photoanodes for PEC water splitting application. Surface modifications of Fe₂O₃ by oxygen evolution catalysts like cobalt phosphate (Co–Pi), a monoclinic BiVO₄ or both showed cathodic/anodic shift in photocurrent with significantly improved photo-response.     

Single crystalline TiO2 nanorods with enhanced visible light activity for solar hydrogen generation

Single crystalline TiO₂ nanorods and polycrystalline nanotubes were fabricated with same length to investigate the effects of their nanostructures on photocatalytic properties for splitting water. In order to enhance the visible light absorbance, TiO₂ nanorods and nanotubes were sensitized with semiconductor nanoparticles such as CdS, CdSe, and CdS/CdSe, and compared in viewpoint of solar hydrogen generation. It was observed that single-crystalline nanorods showed superior photocatalytic properties to polycrystalline nanotubes, and also the potential level of the nanorods with rutile phase was measured as lower than that of the nanotubes with mixture of anatase and rutile. Further improvement of photo-conversion efficiency was obtained by subsequent heat treatments of the sensitized photoelectrodes. It turns out that the improvement is attributed to the improved crystallinity and the increased size of the nanoparticles during the post-annealing treatments. It was demonstrated that TiO₂ nanorods with lower potential level and a single crystalline phase on FTO glass were advantageous for effective charge injection from the sensitized nanoparticles and transport without recombination lost at grain boundaries.     

TiO2 photoanodes for electrically enhanced water splitting

Photoelectrochemical properties of self-organized TiO₂ nanotubes formed by electrochemical anodization of titanium sheets and their working mechanism are investigated. Formation and growth of self-organized nanotubes were carried out by Titanium anodization in acid electrolyte containing fluorides. Annealing of the samples was performed in order to increase the crystallinity of the material. Also some results obtained with samples annealed in Nitrogen atmosphere are presented. Electrochemical Impedance Spectroscopy was used to give an interpretation of the main charge transfer processes that occur at the nanotube/electrolyte interphase. The use of glycerol as hole scavenger was considered in order to improve the photoelectrochemical performance of the samples.     

Photoelectrochemical water splitting on highly smooth and ordered TiO2 nanotube arrays for hydrogen generation

To improve the photoelectrochemical (PEC) water splitting efficiency for hydrogen production, we reported the fabrication of lotus-root-shaped, highly smooth and ordered TiO₂ nanotube arrays (TiO₂ NTs) by a simple and effective two-step anodization method. The TiO₂ NTs prepared in the two-step anodization process (2-step TiO₂ NTs) showed better surface smoothness and tube orderliness than those of TiO₂ NTs prepared in one-step anodization process (1-step TiO₂ NTs). Under illumination of 100 mW/cm² (AM 1.5, simulated solar light) in 1 M KOH solution, water was oxidized on the 2-step TiO₂ NTs electrode with higher efficiency (incident-photon-to-current efficiency of 43.4% at 360 nm and photocurrent density of 0.90 mA/cm² at 1.23 V_RHE) than that on the 1-step TiO₂ NTs electrode. The effective photon-to-hydrogen conversion efficiency was found to be 0.18% and 0.49% for 1-step TiO₂ NTs and 2-step TiO₂ NTs, respectively. These results suggested that the structural smoothness and orderliness of TiO₂ NTs played an important role in improving the PEC water splitting application for hydrogen generation.     

Ultrathin hematite films deposited layer-by-layer on a TiO2 underlayer for efficient water splitting under visible light

Ultrathin hematite (α-Fe₂O₃) film deposited on a TiO₂ underlayer as a photoanode for photoelectrochemical water splitting was described. The TiO₂ underlayer was coated on conductive fluorine-doped tin oxide (FTO) glass by spin coating. The hematite films were formed layer-by-layer by repeating the separated two-phase hydrolysis-solvothermal reaction of iron(III) acetylacetonate and aqueous ammonia. A photocurrent density of 0.683 mA cm⁻² at +1.5 V vs. RHE (reversible hydrogen electrode) was obtained under visible light (>420 nm, 100 mW cm⁻²) illumination. The TiO₂ underlayer plays an important role in the formation of hematite film, acting as an intermediary to alleviate the dead layer effect and as a support of large surface areas to coat greater amounts of Fe₂O₃. The as-prepared photoanodes are notably stable and highly efficient for photoelectrochemical water splitting under visible light. This study provides a facile synthesis process for the controlled production of highly active ultrathin hematite film and a simple route for photocurrent enhancement using several photoanodes in tandem.     

Synthesis of g-C3N4/TiO2 with enhanced photocatalytic activity for H2 evolution by a simple method

A photocatalyst composed of graphite-like carbon nitride (g-C₃N₄) and TiO₂ was fabricated by a simple method to calcine the mixture of melamine and TiO₂ precursor. The photocatalyst has enhanced photoactivity for hydrogen evolution from water. Characterization by XRD, FTIR, SEM and elemental analysis showed that the crystal structure and morphologies of composites were affected by the amount of melamine in the composite. The UV–Vis characterization displayed that the optical absorption range of g-C₃N₄/TiO₂ hybrid was broadened with a synergistic effect. The photoactivity for H₂ evolution was shown that the best result obtained from the composite with 67 wt% melamine has about 5 times improvement compared with bare TiO₂ or pure g-C₃N₄. The enhanced photoactivity might be related with the favorable structure resulted from heat-treatment temperature, and the content of g-C₃N₄ participating in wide optical absorption, separation and transportation of electronic-holes, as well as morphology of composite.     

A novel photoelectrochemical cell with self-organized TiO2 nanotubes as photoanodes for hydrogen generation

A photoelectrochemical (PEC) cell with an innovative design for hydrogen generation via photoelectrocatalytic water splitting is proposed and investigated. It consisted of a TiO₂ nanotube photoanode, a Pt/C cathode and a commercial asbestos diaphragm. The PEC could generate hydrogen under ultraviolet (UV) light-excitation with applied bias in KOH solution. The Ti mesh was used as the substrate to synthesize the self-organized TiO₂ nanotubular array layers. The effect of the morphology of the nanotubular array layers on the photovoltaic performances was investigated. When TiO₂ photocatalyst was irradiated with UV-excitation, it prompted the water splitting under applied bias (0.6 V vs. Normal Hydrogen Electrode, NHE.). Photocurrent generation of 0.58 mA/cm² under UV-light irradiation showed good performance on hydrogen production.     

Morphological, optical and photocatalytic properties of TiO2–Fe2O3 multilayers

Morphological, optical and photocatalytic properties of TiO₂, Fe₂O₃ and TiO₂–Fe₂O₃ samples (formed by 1, 3 and 5 coatings) were studied. The layers were deposited on glass substrate by the sol–gel method. The catalytic activity of the samples was studied by the photodecomposition of methylene blue (MB) under visible light illumination. The FTIR results indicate that all samples present surface OH radicals that are bound either to the Ti or Fe atoms. This effect is better visualized at larger number of coatings in the TiO₂–Fe₂O₃/glass systems. Also, two mechanisms are observed during the photodecomposition of the MB.     

Wet chemical preparation and characterization of electrochromic WO3

Thin films of electrochromic WO₃ were prepared via wet chemical deposition. Precursor solutions containing WOCl₄ in isopropanol were used and films were deposited by spin coating. Various techniques were used for characterization of the films such as Rutherford backscattering spectroscopy (RBS), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), UV-VIS spectroscopy and electrochemical methods. Composition, structural characteristics and electrochromic properties were studied as function of the curing temperature, in the range 80–500°C.     

Stability of gasochromic WO3 films

Gasochromic films consist of an electrochromic layer such as WO₃ and a very thin catalyst coating, like Pt. Hydrogen is dissociated on the catalyst into H atoms, which color the electrochromic film. A complete bleaching can be achieved in oxygen, whereas flushing with argon or evacuating the sample leads to a comparatively slow and incomplete bleaching. We discuss two kinds of aging processes, i.e. catalysed poisoning by reactants in air and a change in the water content of the WO₃. Poisoning by air increases the time needed for coloring in H₂ and bleaching in O₂ or in Ar. From results with variable WO₃ film thicknesses, we conclude that poisoning results from adsorption of a blocking species on the interior surfaces of the WO₃ pores and not on the catalyst. The adsorption process is accelerated by the catalyst. After drying the device at 100°C in vacuum, there was a severe decrease in the coloring and bleaching rates due to a reduction of the diffusion in the WO₃. Furthermore, the coloration at steady state was more intense. The variation of the water content of the WO₃ was attempted by exposing it to dry or humid atmospheres and was investigated by IR spectroscopy. No changes in water content could be detected, and no significant change in the coloration velocity could be found. To demonstrate the long-term stability of the film, a 1.1 m×0.6 m large window was switched 20,000 times at 20°C over 2 yr without any significant change in performance.     

High photocatalytic hydrogen production over the band gap-tuned urchin-like Bi2S3-loaded TiO2 composites system

A new system using Bi₂S₃-loaded TiO₂ photocatalysts (Bi₂S₃/TiO₂) was developed to enhance the production of hydrogen. The Bi₂S₃ (5, 10, 15 wt%) particles in an urchin-like morphology with a length of about 2∼3 μm and a diameter of 15–20 nm, which can absorb all wavelengths in UV–visible radiation, were prepared by solvothermal method and loaded onto nano-sized TiO₂ (10∼15 nm) for photocatalysis on hydrogen production. The evolution of H₂ from methanol/water (1:1) photo splitting over the Bi₂S₃/TiO₂ composite in the liquid system was enhanced, compared with that over pure TiO₂ and Bi₂S₃. In particular, 14.2 ml of H₂ gas was produced after 12 h when 0.5 g of a 10 wt% Bi₂S₃/TiO₂ composite was used. On the basis of cyclic voltammetry (CV) results, the high photoactivity was attributed to the increase of band gap in the Bi₂S₃/TiO₂ composite, due to the decreased recombination between the excited electrons and holes.     

TiO2 and TiO2–SiO2 thin films and powders by one-step soft-solution method: Synthesis and characterizations

Simple soft-solution method has been developed to synthesize films and powders of TiO₂ and mixed TiO₂–SiO₂ at relatively low temperatures. This method is simple and inexpensive. Furthermore, reactor can be designed for large-scale applications as well as to produce large quantities of composite powders in a single step. For the preparation of TiO₂, we used aqueous acidic medium containing TiOSO₄ and H₂O₂, which results in a peroxo-titanium precursor while colloidal SiO₂ has been added to the precursor for the formation of TiO₂–SiO₂. Post annealing at 500 °C is necessary to have anatase structure. Resulting films and powders were characterized by different techniques. TiO₂ (anatase) phase with (1 0 1) preferred orientation has been obtained. Also in TiO₂–SiO₂ mixed films and powders, TiO₂ (anatase) phase was found. Fourier transform infrared spectroscopy (FTIR) results for TiO₂ and mixed TiO₂–SiO₂ films have been presented and discussed. The method developed in this paper allowed obtaining compact and homogeneous TiO₂ films. These compact films are highly photoactive when TiO₂ is used as photo anode in an photoelectrochemical cell. Nanoporous morphology is obtained when SiO₂ colloids are added into the solution.     

Photocatalytic hydrogen production from aqueous methanol solution with CuO/Al2O3/TiO2 nanocomposite

The photocatalytic hydrogen production from aqueous methanol solution was investigated with ZnO/TiO₂, SnO/TiO₂, CuO/TiO₂, Al₂O₃/TiO₂ and CuO/Al₂O₃/TiO₂ nanocomposites. A mechanical mixing method, followed by the solid-state reaction at elevated temperature, was used for the preparation of nanocomposite photocatalyst. Among these nanocomposite photocatalysts, the maximal photocatalytic hydrogen production was observed with CuO/Al₂O₃/TiO₂ nanocomposites. A variety of components of CuO/Al₂O₃/TiO₂ photocatalysts were tested for the enhancement of H₂ formation. The optimal component was 0.2 wt% CuO/0.3 wt% Al₂O₃/TiO₂. The activity exhibited approximately tenfold enhancement at the optimum loading, compared with that with pure P-25 TiO₂. Nano-sized TiO₂ photocatalytic hydrogen technology has great potential for low-cost, environmentally friendly solar-hydrogen production to support the future hydrogen economy.     

The obstructed diffusion of the I3 ion in mesoscopic TiO2 membranes

The diffusional permeability of I⁻₃ ion in acetonitrile in free standing TiO₂ membrane with a porosity of 55% was examined. The apparent diffusion coefficient, D_app at 25°C of the ion was found to be 3.4×10⁻⁶ cm^{2 −1}, an order of magnitude smaller than the free diffusion at the same temperature. The temperature dependency of D_app was measured in the range 0–30°C and analysed in terms of the Walden product. The diffusional activation energy was found to be 13.5 kJ/mol. The parameters of interest for the efficiency of mesoscopic wet solar cells are discussed. A back of an envelope calculation shows that although the obstructed diffusion coefficient of the I⁻₃ ion was an order of magnitude smaller than the free diffusion the diffusional flux is still sufficient to meet a current density of 50 mA cm⁻². At incident photon flux of 1 kW m⁻² and at a photopotential of 0.6 V this would correspond to a solar energy efficiency of approximately 30%.     

Cycle test and degradation analysis of WO3/PC+LiClO4/CeO2·TiO2 electrochromic device

We fabricated an electrochromic full cell device adopting WO₃ as a working electrode, and 1 M LiClO₄ in PC with 3% water addition as an electrolyte and CeO₂·TiO₂ with various thicknesses as an ion storage layer. CeO₂·TiO₂ with less than 100 nm shows large charge density but the long-term cyclability is not good due to lithium ion diffusion into ITO thin film. Therefore, the thickness of CeO₂·TiO₂ ion storage layer should be coated at more than 200 mm/min. Long-term cycle test results show that CeO₂·TiO₂ ion storage layer with more than 150 nm thickness and two time coating enhance the long-term stability. SIMS analysis results show that the degradation is due to the remaining lithium ion in the working electrode, WO₃.