Synthesis of g-C3N4/TiO2 with enhanced photocatalytic activity for H2 evolution by a simple method

A photocatalyst composed of graphite-like carbon nitride (g-C₃N₄) and TiO₂ was fabricated by a simple method to calcine the mixture of melamine and TiO₂ precursor. The photocatalyst has enhanced photoactivity for hydrogen evolution from water. Characterization by XRD, FTIR, SEM and elemental analysis showed that the crystal structure and morphologies of composites were affected by the amount of melamine in the composite. The UV–Vis characterization displayed that the optical absorption range of g-C₃N₄/TiO₂ hybrid was broadened with a synergistic effect. The photoactivity for H₂ evolution was shown that the best result obtained from the composite with 67 wt% melamine has about 5 times improvement compared with bare TiO₂ or pure g-C₃N₄. The enhanced photoactivity might be related with the favorable structure resulted from heat-treatment temperature, and the content of g-C₃N₄ participating in wide optical absorption, separation and transportation of electronic-holes, as well as morphology of composite.     

g-C3N4/TiO2可见光催化降解磺胺甲恶唑的研究

以TiO₂颗粒和三聚氰胺为原料,采用高温煅烧法制备g-C₃N₄/TiO₂复合光催化材料,研究其对仿生生态系统中磺胺类抗生素的去除效果。利用扫描电子显微镜（SEM）、X射线衍射仪(XRD)、傅里叶变换红外光谱仪（FTIR）、紫外可见分光光度计（UV-vis DRS）对g-C₃N₄/TiO₂进行表征,并研究在可见光条件下g-C₃N₄/TiO₂对溶液中磺胺甲恶唑（SMX）的光催化降解效果。结果表明,g-C₃N₄/TiO₂具有良好的光催化活性,在可见光照射下,当g-C₃N₄/TiO₂投加量为0.2 g·L^-1时,对初始质量浓度为200 μg·L^-1的SMX的去除率可达84.3%。在相同条件下,而g-C₃N₄和TiO₂只能分别去除21.0%和16.0%的SMX,同时在仿生系统中12.37 g·m^-2 g-C₃N₄/TiO₂可以去除95.35%的SMX。通过质谱分析推测,SMX可能的降解路径分别为S—N键断裂、C—N键断裂、S—C键断裂、SMX的羟基化和SMX上氨基的硝化反应,两种可能的中间产物分别为对氨基苯磺酰胺和3-氨基-5-甲基异恶唑。     

Efficient visible-light-driven photocatalytic H2 production over Cr/N-codoped SrTiO3

Visible-light-response Cr/N-codoped SrTiO₃ was prepared by a sol–gel hydrothermal method. The comparison studies indicate that Cr-doped and Cr/N-codoped SrTiO₃ can be synthesized by this means, but not the N-doped SrTiO₃. The theoretical calculations exhibit the defect formation energy of the Cr/N codoping into SrTiO₃ is much smaller than that of the N doping into SrTiO₃, illuminating that the incorporation of Cr can promote the N doping into the O sites in the SrTiO₃. Compared to the Cr-doped SrTiO₃, the Cr/N-codoped SrTiO₃ photocatalyst shows the high photocatalytic activities for hydrogen production with the quantum efficiency of 3.1% at 420 nm, due to the smaller band gap and much less vacancy defects.     

Photoelectrochemical study on charge transfer properties of nanostructured Fe2O3 modified by g-C3N4

Novel photocatalysts, which consist of two visible light responsive semiconductors including graphite-like carbon nitride (g-C₃N₄) and Fe₂O₃, were successfully synthesized via electrodeposition followed by chemical vapor deposition. The morphology of the g-C₃N₄/Fe₂O₃ can be tuned from regular nanosheets to porous cross-linked nanostructures. Remarkably, the optimum activity of the g-C₃N₄/Fe₂O₃ is almost 70 times higher than that of individual Fe₂O₃ for photoelectrochemical water splitting. The enhancement of photoelectrochemical activity could be assigned to the morphology change of the photocatalysts and the effective separation and transfer of photogenerated electrons and holes originated from the intimately contacted interfaces. The g-C₃N₄/Fe₂O₃ composites could be developed as high performance photocatalysts for water splitting and other optoelectric devices.     

Green synthesis of fibrous hierarchical meso-macroporous N doped TiO2 nanophotocatalyst with enhanced photocatalytic H2 production

A new approach to prepare hierarchical and fibrous meso-macroporous N-doped TiO₂ is attempted at room temperature without using templates by the addition of titanium isopropoxide droplets to the ammonia solution. The catalysts are thoroughly characterized by physico-chemical and spectroscopic method to explore the structural, electronic and optical properties. The photocatalytic activities of the catalyst were evaluated with hydrogen generation. NTP catalyst calcined at 400 °C (NTP-400) exhibited 602.7 μmol/3 h H₂ generation from 10 vol.% methanol under visible light. The excellent photocatalytic activity for NTP-400 is attributed to the porous networks existing in our system with uniform N dispersion throughout the catalyst. The hierarchical and fibrous structures allow easy channelization of electron as in the case of nanotubes for effective surface charge transfer. Along with macroporosity, nitrogen incorporation and mesoporosity play some important roles for enhanced photoactivities.     

Synthesis of mesoporous-assembled TiO2 nanocrystals by a modified urea-aided sol-gel process and their outstanding photocatalytic H2 production activity

Mesoporous-assembled TiO₂ nanocrystals with very high photocatalytic H₂ production activity were synthesized through a modified sol-gel process with the aid of urea as mesopore-directing agent, heat-treated under various calcination temperatures, and assessed for their photocatalytic H₂ production activity via water splitting reaction. The resulting mesoporous-assembled TiO₂ nanocrystals were systematically characterized by N₂ adsorption-desorption analysis, surface area and pore size distribution analyses, X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The experimental results showed that the photocatalytic H₂ production activity of the synthesized mesoporous-assembled TiO₂ nanocrystal calcined at 500 °C, which possessed very narrow pore size distribution, was extraordinarily higher than that of the commercially available P-25 TiO₂ and ST-01 TiO₂ powders.     

Improved photocatalytic H2 production assisted by aqueous glucose biomass by oxidized g-C3N4

Chemically modified g-C₃N₄ for the photocatalytic H₂ evolution from water was explored. Bulk g-C₃N₄ was treated in hot HNO₃ aqueous solution to obtain the oxidized material (o-g-C₃N₄), tested in water containing glucose as model water-soluble sacrificial biomass, using Pt as co-catalyst, under simulated solar light. The behaviour of o-g-C₃N₄ was studied in relation with catalyst amount, Pt loading, glucose concentration. Results showed that H₂ production is favoured by increasing glucose concentration up to 0.1 M and Pt loading up to 3 wt%, and it resulted strongly enhanced using small amount of o-g-C₃N₄ (0.25 g L^?1). o-g-C₃N₄ possesses superior photocatalytic activity (～26-fold higher) compared to pristine g-C₃N₄, with H₂ evolution further improved by ultrasound-assisted exfoliation and evolution rates up to ca. 1370 μmol h^?1 per gram of catalyst, with excellent reproducibility (RSD < 6%, n = 3). Significant production was observed also in river water and seawater, with results far better (up to ca. 2500 μmol g^?1 h^?1) compared to commercial AEROXIDE^® P25 TiO₂ under natural solar light.     

High photocatalytic hydrogen production over the band gap-tuned urchin-like Bi2S3-loaded TiO2 composites system

A new system using Bi₂S₃-loaded TiO₂ photocatalysts (Bi₂S₃/TiO₂) was developed to enhance the production of hydrogen. The Bi₂S₃ (5, 10, 15 wt%) particles in an urchin-like morphology with a length of about 2∼3 μm and a diameter of 15–20 nm, which can absorb all wavelengths in UV–visible radiation, were prepared by solvothermal method and loaded onto nano-sized TiO₂ (10∼15 nm) for photocatalysis on hydrogen production. The evolution of H₂ from methanol/water (1:1) photo splitting over the Bi₂S₃/TiO₂ composite in the liquid system was enhanced, compared with that over pure TiO₂ and Bi₂S₃. In particular, 14.2 ml of H₂ gas was produced after 12 h when 0.5 g of a 10 wt% Bi₂S₃/TiO₂ composite was used. On the basis of cyclic voltammetry (CV) results, the high photoactivity was attributed to the increase of band gap in the Bi₂S₃/TiO₂ composite, due to the decreased recombination between the excited electrons and holes.     

H2SO4 stability of PBI-blend membranes for SO2 electrolysis

For hydrogen to become a serious contender for replacing fossil fuels, the manufacturing thereof has to be further investigated. One such process, the membrane based Hybrid Sulfur (HyS) process, where hydrogen is produced from the electrolysis of SO₂, has received considerable interest recently. Since H₂SO₄ is formed during SO₂ electrolysis, H₂SO₄ stability is a prerequisite for any membrane to be used in this process. In this study, pure as well as blended polybenzimidazole (PBI), partially fluorinated poly(arylene ether) (sFS) and nonfluorinated poly(arylene ethersulfone) (sPSU) membranes were investigated in terms of their acid stability as a function of acid concentration. Membranes were characterized using weight change, TGA, GPC, SEM/EDX and IEC. While a general stability was observed at 30 and 60 wt% H₂SO₄, the blended sFS-PBI and sPSU-PBI showed the highest stability throughout. According to the VI curve obtained for the SO₂ electrolysis, the sPSU-PBI blend membrane performed slightly better than Nafion^®117.     

Enhancement of the H2 desorption properties of LiAlH4 doping with NiCo2O4 nanorods

Lithium aluminum hydride (LiAlH₄) is considered as an attractive candidate for hydrogen storage owing to its favorable thermodynamics and high hydrogen storage capacity. However, its reaction kinetics and thermodynamics have to be improved for the practical application. In our present work, we have systematically investigated the effect of NiCo₂O₄ (NCO) additive on the dehydrogenation properties and microstructure refinement in LiAlH₄. The dehydrogenation kinetics of LiAlH₄ can be significantly increased with the increase of NiCo₂O₄ content and dehydrogenation temperature. The 2 mol% NiCo₂O₄-doped LiAlH₄ (2% NCO–LiAlH₄) exhibits the superior dehydrogenation performances, which releases 4.95 wt% H₂ at 130 °C and 6.47 wt% H₂ at 150 °C within 150 min. In contrast, the undoped LiAlH₄ sample just releases <1 wt% H₂ after 150 min. About 3.7 wt.% of hydrogen can be released from 2% NCO–LiAlH₄ at 90 °C, where total 7.10 wt% of hydrogen is released at 150 °C. Moreover, 2% NCO–LiAlH₄ displayed remarkably reduced activation energy for the dehydrogenation of LiAlH₄.     

CuCr2O4/TiO2 heterojunction for photocatalytic H2 evolution under simulated sunlight irradiation

CuCr₂O₄/TiO₂ heterojunction has been successfully synthesized via a facile citric acid (CA)-assisted sol-gel method. Techniques of X-ray diffraction (XRD), transmission electron microscopy (TEM), and UV-vis diffuse reflectance spectrum (UV-vis DRS) have been employed to characterize the as-synthesized nanocomposites. Furthermore, photocatalytic activities of the as-obtained nanocomposites have been evaluated based on the H₂ evolution from oxalic acid solution under simulated sunlight irradiation. Factors such as CuCr₂O₄ to TiO₂ molar ratio in the composites, calcination temperature, photocatalyst mass concentration, and initial oxalic acid concentration affecting the photocatalytic hydrogen producing have been studied in detail. The results showed that the nanocomposite of CuCr₂O₄/TiO₂ is more efficient than their single part of CuCr₂O₄ or TiO₂ in producing hydrogen. The optimized composition of the nanocomposites has been found to be CuCr₂O₄·0.7TiO₂. And the optimized calcination temperature and photocatalyst mass concentration are 500 °C and 0.8 g l⁻¹, respectively. The influence of initial oxalic acid concentration is consistent with the Langmuir model.     

Visible-light-driven ZnIn2S4/CdIn2S4 composite photocatalyst with enhanced performance for photocatalytic H2 evolution

ZnIn₂S₄/CdIn₂S₄ composite photocatalysts (x = 0–1) were successfully synthesized via a hydrothermal route. Compositions of ZnIn₂S₄/CdIn₂S₄ composite photocatalysts were optimized according to the photocatalytic H₂ evolution rate. XRD patterns indicate the as-prepared samples are mixtures of hexagonal and cubic structures. FESEM and TEM images show that the as-prepared samples are composed of flower-like microspheres with wide distribution of diameter. There is obviously distinguishing distribution of Zn, Cd elements among the composite architectures. UV–vis absorption spectra of different compositions exhibit that absorption edges of ZnIn₂S₄/CdIn₂S₄ composites slightly move towards longer wavelengths with the increment of CdIn₂S₄ component. A typical time course of photocatalytic H₂ evolution from an aqueous Na₂SO₃ and Na₂S solution over unloaded and PdS-loaded ZnIn₂S₄/CdIn₂S₄ composite photocatalyst is carried out. The initial activity for H₂ evolution over 0.75 wt% PdS-loaded sample is up to 780 μmol h⁻¹. And the activity of unloaded sample also reaches 490 μmol h⁻¹ with consistent stability.     

g-C3N4 coated SrTiO3 as an efficient photocatalyst for H2 production in aqueous solution under visible light irradiation

A highly active photocatalyst based on g-C₃N₄ coated SrTiO₃ has been synthesized simply by decomposing urea in the presence of SrTiO₃ at 400 °C. The catalyst demonstrates a high H₂ production rate ∼440 μmol h⁻¹/g catalyst in aqueous solution under visible light irradiation, which is much higher than conventional anion doped SrTiO₃ or physical mixtures of g-C₃N₄ and SrTiO₃. The improved photocatalytic activity can be ascribed to the close interfacial connections between g-C₃N₄ and SrTiO₃ where photo-generated electron and holes are effectively separated. The newly synthesized catalyst also exhibited a stable performance in the repeated experiments.     

HDMR correlations for the laminar burning velocity of premixed CH4/H2/O2/N2 mixtures

Correlations for the laminar burning velocity of premixed CH₄/H₂/O₂/N₂ mixtures were developed using the method of High Dimensional Model Representation (HDMR). Based on experiment data over a wide range of conditions reported in the literature, two types of HDMR correlation (i.e. global and piecewise HDMR correlations) were obtained. The performance of these correlations was assessed through comparison with experimental results and the correlation reported in the literature. The laminar burning velocity predicted by the piecewise HDMR correlations was shown to agree very well with those from experiments. Therefore, the piecewise HDMR correlations can be used as an effective replacement for the full chemical mechanism when the prediction of the laminar burning velocity is needed in certain combustion modeling.     

Morphological, optical and photocatalytic properties of TiO2–Fe2O3 multilayers

Morphological, optical and photocatalytic properties of TiO₂, Fe₂O₃ and TiO₂–Fe₂O₃ samples (formed by 1, 3 and 5 coatings) were studied. The layers were deposited on glass substrate by the sol–gel method. The catalytic activity of the samples was studied by the photodecomposition of methylene blue (MB) under visible light illumination. The FTIR results indicate that all samples present surface OH radicals that are bound either to the Ti or Fe atoms. This effect is better visualized at larger number of coatings in the TiO₂–Fe₂O₃/glass systems. Also, two mechanisms are observed during the photodecomposition of the MB.     

Self-doped Ti@TiO2 visible light photocatalyst: Influence of synthetic parameters on the H2 production activity

Self-doped TiO₂ shows visible light photocatalytic activity, while pristine TiO₂ is only UV responsive. Ti³⁺ has been demonstrated to be responsible for this improvement. We systematically studied various experimental parameters, such as the amount of reducing agent imidazole, types of imidazoles and Ti sources, and determined effects of these parameters on the combustion process and final materials. The phase composition, Ti³⁺ concentration, light absorption, surface area, and crystallinity of the product are significantly affected by the amount of imidazoles. Through comparing different imidazoles, we found that only flammable/combustible imidazoles are able to convert Ti⁴⁺ into Ti³⁺. This result is very helpful in understanding the mechanism and reactions in combustion process. Titanium precursors also have a great influence in production of Ti³⁺ doped TiO₂ materials. Titanium alkoxides allow the successful synthesis of blue partially reduced TiO₂, while TiCl₄ only lead to white pristine TiO₂.     

Ultrasonic spray pyrolysis synthesis of Ag/TiO2 nanocomposite photocatalysts for simultaneous H2 production and CO2 reduction

Simultaneous photocatalytic hydrogen production and CO₂ reduction (to form CO and CH₄) from water using methanol as a hole scavenger were investigated using silver-modified TiO₂ (Ag/TiO₂) nanocomposite catalysts. A simple ultrasonic spray pyrolysis (SP) method was used to prepare mesoporous Ag/TiO₂ composite particles using TiO₂ (P25) and AgNO₃ as the precursors. The material properties and photocatalytic activities were compared with those prepared by a conventional wet-impregnation (WI) method. It was found that the samples prepared by the SP method had a larger specific surface area and a better dispersion of Ag nanoparticles on TiO₂ than those prepared by the WI method, and as a result, the SP samples showed much higher photocatalytic activities toward H₂ production and CO₂ reduction. The optimal Ag concentration on TiO₂ was found to be 2 wt%. The H₂ production rate of the 2% Ag/TiO₂–SP sample exhibited a six-fold enhancement compared with the 2% Ag/TiO₂–WI sample and a sixty-fold enhancement compared with bare TiO₂. The molar ratio of H₂ and CO in the final products can be tuned in the range from 2 to 10 by varying the reaction gas composition, suggesting a viable way of producing syngas (a mixture of H₂ and CO) from CO₂ and water using the prepared Ag/TiO₂ catalysts with energy input from the sun.     

Aging of LiFePO4 upon exposure to H2O

The effect of H₂O on carbon-coated LiFePO₄ particles was investigated by chemical analysis, structural analysis (X-ray diffraction, SEM, TEM), optical spectroscopy (FTIR, Raman) and magnetic measurements. Upon immersion in water, part of the product floats while the main part sinks. Both the floating and the sinking part have been analyzed. We find that the floating and sinking part only differ by the amount of carbon that partly detaches from the particles upon immersion in water. Exposure to H₂O results in rapid attack, within minutes, of the surface layer of the particles, because the particles are no longer protected by carbon. The deterioration of the carbon coat is dependent on the synthesis process, either hydrothermal or solid-state reaction. In both cases, however, the carbon coat is permeable to water and fails to protect the surface of the LiFePO₄ particles. The consequence is that this immersion results in the chemical attack of LiFePO₄, but is restricted to the surface layer of the particles (few nanometers-thick). In case the particles are simply exposed to humid air, the carbon coat protects the particles more efficiently. In this case, the exposure to H₂O mainly results in the delithiation of the surface layer, due to the hydrophilic nature of Li, and only the surface layer is affected, at least for a reasonable time of exposure to humid air (weeks). In addition, within this timescale, the surface layer can be chemically lithiated again, and the samples can be dried to remove the moisture, restoring the reversible electrochemical properties.     

The effects of micellar media on the photocatalytic H2 production from water

The photocatalytic H₂ production efficiency of a multi-component system, containing [Ir(ppy)₂(bpy)]⁺ as photosensitizer, [Co(bpy)₃]²⁺ as H₂-evolving catalyst, and triethanolamine (TEOA) as sacrificial electron donor, was investigated in water/acetonitrile (8:2, v/v) solution in the presence of different kinds of surfactants, such as cetyl trimethyl ammonium bromide (CTAB), Triton X-100, and sodium lauryl sulfonate (NaLS). The H₂ evolution rate is found to follow the order of cationic micellar media > nonionic micellar media > anionic micellar media > water/acetonitrile solution. The underlying mechanism was discussed.     

Effect of H2O2 on Pt electrode dissolution in H2SO4 solution based on electrochemical quartz crystal microbalance study

The effect of H₂O₂ on the Pt dissolution in 0.5 mol dm⁻³ H₂SO₄ was investigated using an electrochemical quartz crystal microbalance (EQCM). For the potential cycling at 50 mV s⁻¹, the Pt weight irreversibly decreases in a N₂ atmosphere with H₂O₂, while only a negligible Pt weight-loss is observed in the N₂ and O₂ atmospheres without H₂O₂. The EQCM data measured by the potential step showed that the Pt dissolution in the presence of H₂O₂ depends on the electrode potential and the H₂O₂ concentration. For the stationary electrolysis, the Pt dissolution occurs at 0.61–1.06 and 1.06–1.36 V vs. RHE. It should be noted that the Pt dissolution phenomenon in the presence of H₂O₂ is also affected by the potential scanning time. Based on these results, H₂O₂ is considered not only to contribute to the formation of Pt-oxide causing the cathodic Pt dissolution, but also to participate in the anodic Pt dissolution and the chemical Pt dissolution.