Experimental investigation of the combustion characteristics,emissions and performance of hydrogen port fuel injection in a diesel engine

Diesel engines are indispensable in daily life. However, the limited supply of petroleum fuels and the stringent regulations on such fuels are forcing researchers to study the use of hydrogen as a fuel. In this study, a diesel engine is operated using hydrogen–diesel dual fuel, where hydrogen is introduced into the intake manifold using an LPG-CNG injector and pilot diesel is injected using diesel injectors. The energy contents of the total fuel, 0%, 16%, 36% and 46% hydrogen (the 0% hydrogen energy fraction represents neat diesel fuel), were tested at 1300 rpm of constant engine speed and 5.1 kW of constant indicated power. According to test results, the indicated thermal efficiency of the engine decreases and the isfc increases with an increasing hydrogen energy fraction. Additionally, indicated specific CO, CO₂ and smoke emissions decrease with an increasing percentage of hydrogen fuel. However, indicated specific NO_x emissions do not change at the 16% hydrogen energy fraction, in other words, with an increase in the hydrogen amount (36% and 46% hydrogen energy fraction of total fuel), a dramatic increase (58.8% and 159.7%, respectively) is observed. Additionally, the peak in-cylinder pressure and the peak heat release rate values increase with the increasing hydrogen rate.     

Preparation,characterization, engine combustion and emission characteristics of rapeseed oil based hybrid fuels

In this study, hybrid fuels consisting of rapeseed oil/diesel blend, 1% aqueous ethanol and a surfactant (oleic acid/1-butanol mixture) were prepared and tested as a fuel in a direct injection (DI) diesel engine. The main fuel properties such as the density, viscosity and lower heating value (LHV) of these fuels were measured, and the engine performance, combustion and exhaust emissions were investigated and compared with that of diesel fuel. The experimental results showed that the viscosity and density of the hybrid fuels were decreased and close to that of diesel fuel with the increase of ethanol volume fraction up to 30%. The start of combustion was later than that of diesel fuel and the peak cylinder pressure, peak pressure rise rate and peak heat release rate were higher than those of diesel fuel. The brake specific fuel consumption (BSFC) of hybrid fuels was increased with the volume fraction of ethanol and higher than that of diesel. The brake specific energy consumption (BSEC) was almost identical for all test fuels. The smoke emissions were lower than those for diesel fuel at high engine loads, the NO_x emissions were almost similar to those of diesel fuel, but CO and HC emissions were higher, especially at low engine loads.     

Combustion,performance and emissions of a diesel engine with H2, CH4 and H2–CH4 addition

Experiments were conducted to investigate the combustion and emission characteristics of a diesel engine with addition of hydrogen or methane for dual-fuel operation, and mixtures of hydrogen–methane for tri-fuel operation. The in-cylinder pressure and heat release rate change slightly at low to medium loads but increase dramatically at high load owing to the high combustion temperature and high quantity of pilot diesel fuel which contribute to better combustion of the gaseous fuels. The performance of the engine with tri-fuel operation at 30% load improves with the increase of hydrogen fraction in methane and is always higher than that with dual-fuel operations. Compared with ULSD–CH₄ operation, hydrogen addition in methane contributes to a reduction of CO/CO₂/HC emissions without penalty on NO_x emission. Dual-fuel and tri-fuel operations suppress particle emission to the similar extent. All the gaseous fuels reduce the geometry mean diameter and total number concentration of diesel particulate. Tri-fuel operation with 30% hydrogen addition in methane is observed to be the best fuel in reducing particulate and NO_x emissions at 70 and 90% loads.     

Assessment of combustion and exhaust emissions in a common-rail diesel engine fueled with methane and hydrogen/methane mixtures under different compression ratio

This study investigates the potential usage of the methane and hydrogen enriched methane in a turbocharged common-rail direct injection diesel engine. Methane and hydrogen/methane mixtures are sent through the air intake manifold of the engine. The engine is operated at four different loads and three different compression ratios. Results are compared amongst single diesel and dual-fuel operations at different compression ratios and load conditions. Compared to diesel, dual-fuel operations mostly generate higher and advanced peak in-cylinder gas pressure, more combustion noise, late pilot injection and start of combustion, advanced combustion center, substantial variations at ignition delay and combustion duration, a significant increase in cyclic variations at low and medium loads, and earlier heat release. Hydrogen enrichment decreases evidently specific fuel consumption. Concerning emissions, compared to diesel operation, dual-fuel operations produce higher total hydrocarbon (THC) and nitrogen oxides (NO_x) but lower carbon dioxide (CO₂). Hydrogen substitutions decrease THC and CO₂ emissions of methane dual-fuel operations approximately between 9-29% and 1–32%, respectively. Smoke emission of dual-fuel operations is less than that of diesel at low and medium loads, whereas it sharply increases at high load. Knocking occurs at high compression ratio and load conditions with dual-fuel operations and dramatically increases with increasing hydrogen ratio. Decreasing the compression ratio notably reduces the combustion noise as well as some emissions, such as NO_x, CO₂ and smoke, for entire load ranges of dual-fuel and diesel operations.     

Combining GTL fuel,reformed EGR and HC-SCR aftertreatment system to reduce diesel NOx emissions. A statistical approach

An ultra-low sulphur diesel (ULSD) fuel and a synthetic gas-to-liquid (GTL) fuel, besides different types of standard and reformed EGR, were evaluated in a single-cylinder, direct injection, diesel engine equipped with hydrocarbon-selective catalytic reduction (HC-SCR) aftertreatment system. The results obtained were statistically analysed (at 95% statistical significance) to identify the most significant factors that affect NO_x emissions and to search for the optimum operation conditions in order to minimize these emissions. For that purpose, a fully crossed factorial experimental design was used, including two different engine speeds (1200 and 1500 rpm), two engine loads (25% and 50%), and four EGR/REGR ratios (0%, 10%, 20% and 30%) resulting in almost one hundred tests. An optimal combination of fuel type, REGR type and REGR ratio was proved to reduce around 89–95% of the reference NO_x emissions. In general, at 25% engine load GTL fuelling combined with the reformed EGR with the highest hydrogen content was found the most desirable, as the hydrogen sharply increased the NO_x conversion in the SCR catalyst. Differently, at 50% load standard EGR was sufficient to reach high NO_x reductions. These findings may be used for the implementation of a system on-board capable to switch from EGR to REGR, which will help engine manufacturers to meet the future emission regulations.     

Effect of hydrogen supplementation on engine performance and emissions

Vehicular Pollution and environmental degradation are on the rise with increasing vehicles and to stop this strict regulation have been put on vehicular emissions. Also, the depleting fossil fuels are of great concern for energy security. This has motivated the researchers to invest considerable resources in finding cleaner burning, sustainable and renewable fuels. However renewable fuels independently are not sufficient to deal with the problem at hand due to supply constraints. Hence, advanced combustion technologies such as homogeneous charge compression ignition (HCCI), low-temperature combustion (LTC), and dual fuel engines are extensively researched upon. In this context, this work investigates dual fuel mode combustion using a constant speed diesel engine, operated using hydrogen and diesel. The engine is operated at 25, 50 and 75% loads and substitution of diesel energy with hydrogen energy is done as 0, 5, 10 and 20%. The effect of hydrogen energy share (HES) enhancement on engine performance and emissions is investigated. In the tested range, slightly detrimental effect of HES on brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) is observed. Comparision of NO and NO₂ emissions is done to understand the non-thermal influence of H₂ on the NO_x emissions. Hence, HES is found beneficial in reducing harmful emissions at low and mid loads.     

Effect of natural antioxidant additive on hydrogen-enriched biodiesel operated compression ignition engine

The environmental degradation and depletion of fossil fuel, urges the need of renewable fuel for IC engines. Among the renewable fuel, biodiesel are widely used as alternative fuel but for recent years hydrogen is also considered as alternative fuel because of zero emission but it possess higher auto ignition temperature. In order to reduce the self-ignition temperature of hydrogen and another liquid fuel is mixed and operated as a dual fuel mode condition in CI engine. The current investigation aims to analyse the impact of natural antioxidant additive on hydrogen-enriched biodiesel operation in a diesel engine. During the experimentation process hydrogen is admitted at the intake manifold and B20 blend of juliflora biodiesel is injected in combustion cylinder. The three test fuel samples are used for the experimentation process such as diesel, B20 and B20 with hydrogen in different flow rates such as 8, 10, 12, 16,20lpm. B20 with hydrogen shows an increment of brake thermal efficiency (BTE). Among the test fuels B20 + 16lpm and B20 + 20lpm blends have better improvement of BTE of 28.815% and 28.32%, which is higher than the conventional engine at maximum load CO, HC emission is also lower for B20 + 16lpm and B20 + 20lpm than other blends but the NO_x emission increases of 26 and 28% than diesel respectively. In order to minimize the NO_x emission, natural antioxidant additive Melia Azedarach (MA) of 1000 ppm is added to B20 + 16lpm and found that B20 + 16lpm with MA shows an improvement of BTE 2.17% higher than B20 + 16lpm without additive and the NO_x emission for B20 + 16lpm with additive is 1079 ppm, which is 21.9% lower than B20 + 16lpm without additives. Therefore B20 + 16lpm with additive is superior than other test blends.     

Effect of manifold injection of hydrogen gas in producer gas and neem biodiesel fueled CRDI dual fuel engine

The high flammability of hydrogen gas gives it a steady flow without throttling in engines while operating. Such engines also include different induction/injection methods. Hydrogen fuels are encouraging fuel for applications of diesel engines in dual fuel mode operation. Engines operating with dual fuel can replace pilot injection of liquid fuel with gaseous fuels, significantly being eco-friendly. Lower particulate matter (PM) and nitrogen oxides (NO_x) emissions are the significant advantages of operating with dual fuel.Consequently, fuels used in the present work are renewable and can generate power for different applications. Hydrogen being gaseous fuel acts as an alternative and shows fascinating use along with diesel to operate the engines with lower emissions. Such engines can also be operated either by injection or induction on compression of gaseous fuels for combustion by initiating with the pilot amount of biodiesel. Present work highlights the experimental investigation conducted on dual fuel mode operation of diesel engine using Neem Oil Methyl Ester (NeOME) and producer gas with enriched hydrogen gas combination. Experiments were performed at four different manifold hydrogen gas injection timings of TDC, 5°aTDC, 10°aTDC and 15°aTDC and three injection durations of 30°CA, 60°CA, and 90°CA. Compared to baseline operation, improvement in engine performance was evaluated in combustion and its emission characteristics. Current experimental investigations revealed that the 10°aTDC hydrogen manifold injection with 60°CA injection duration showed better performance. The BTE of diesel + PG and NeOME + PG operation was found to be 28% and 23%, respectively, and the emissions level were reduced to 25.4%, 14.6%, 54.6%, and 26.8% for CO, HC, smoke, and NO_x, respectively.     

Effect on performance and emissions of a dual fuel diesel engine using hydrogen and producer gas as secondary fuels

Energy is an essential prerequisite for economical and social growth of any country. Skyrocketing of petroleum fuel cost s in present day has led to growing interest in alternative fuels like CNG, LPG, Producer gas, Biogas in order to provide suitable substitute to diesel for a compression ignition engine. This paper discusses some experimental investigations on dual fuel operation of a 4 cylinder (turbocharged and intercooled) 62.5 kW gen-set diesel engine with hydrogen, producer gas (PG) and mixture of producer gas and hydrogen as secondary fuels. Results on brake thermal efficiency and emissions, namely, un-burnt hydrocarbon (HC), carbon monoxide (CO), and NO_x are presented here. The paper also contains vital information relating to the performances of an engine at a wide range of load conditions with different gaseous fuel substitutions. When only hydrogen is used as secondary fuel, maximum increase in the brake thermal efficiency is 7% which is obtained with 20% of secondary fuel. When only producer gas is used as secondary fuel, maximum decrease in the brake thermal efficiency of 8% is obtained with 30% of secondary fuel. Compared to the neat diesel operation, proportion of un-burnt HC and CO increases, while, emission of NO_x reduces in all Cases. On the other hand, when 40% of mixture of producer gas and hydrogen is used (in the ratio (60:40) as secondary fuel, brake thermal efficiency reduces marginally by 3%. Further, shortcoming of low efficiency at lower load condition in a dual fuel operation is removed when a mixture of hydrogen and producer gas is used as the secondary fuel at higher than 13% load condition. Based on the performance studied, a mixture of producer gas and hydrogen in the proportion of 60:40 may be used as a supplementary fuel for diesel conservation.     

船用发动机有害排放气体的评价及处理研究——燃料性质和输出轴扭...

为了评价船有发动机有害气体的排放,本从燃料的性质着手,较为详细地对不同性质的１３种燃烧进行了研究,并在一台中型四冲程船用柴油机上进行了试验,测定了各种有害排气的浓度、发动机的性能和燃烧特性,对燃料的性质与排放之间的相关性进行了探讨。进一步调查研究了柴油机运转工况的不同及输出轴扭矩的变化对ＮＯｘ排放的影响。由试验结果可知：对于周期性输出扭矩的变化,ＮＯｘ的排放也发生周期性的变化。但是,柴油机在高输     

Effect of injection timing on the exhaust emissions of a diesel engine using diesel–methanol blends

Environmental concerns and limited resource of petroleum fuels have caused interests in the development of alternative fuels for internal combustion (IC) engines. For diesel engines, alcohols are receiving increasing attention because they are oxygenated and renewable fuels. Therefore, in this study, the effect of injection timing on the exhaust emissions of a single cylinder, naturally aspirated, four-stroke, direct injection diesel engine has been experimentally investigated by using methanol-blended diesel fuel from 0% to 15% with an increment of 5%. The tests were conducted for three different injection timings (15°, 20° and 25 °CA BTDC) at four different engine loads (5 Nm, 10 Nm, 15 Nm, 20 Nm) at 2200 rpm. The experimental test results showed that Bsfc, NO_x and CO₂ emissions increased as BTE, smoke opacity, CO and UHC emissions decreased with increasing amount of methanol in the fuel mixture. When compared the results to those of original injection timing, NO_x and CO₂ emissions decreased, smoke opacity, UHC and CO emissions increased for the retarded injection timing (15 °CA BTDC). On the other hand, with the advanced injection timing (25 °CA BTDC), decreasing smoke opacity, UHC and CO emissions diminished, and NO_x and CO₂ emissions boosted at all test conditions. In terms of Bsfc and BTE, retarded and advanced injection timings gave negative results for all fuel blends in all engine loads.     

Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Combustion and performance evaluation of a diesel engine fueled with biodiesel produced from soybean crude oil

In this study, the biodiesel produced from soybean crude oil was prepared by a method of alkaline-catalyzed transesterification. The important properties of biodiesel were compared with those of diesel. Diesel and biodiesel were used as fuels in the compression ignition engine, and its performance, emissions and combustion characteristics of the engine were analyzed. The results showed that biodiesel exhibited the similar combustion stages to that of diesel, however, biodiesel showed an earlier start of combustion. At lower engine loads, the peak cylinder pressure, the peak rate of pressure rise and the peak of heat release rate during premixed combustion phase were higher for biodiesel than for diesel. At higher engine loads, the peak cylinder pressure of biodiesel was almost similar to that of diesel, but the peak rate of pressure rise and the peak of heat release rate were lower for biodiesel. The power output of biodiesel was almost identical with that of diesel. The brake specific fuel consumption was higher for biodiesel due to its lower heating value. Biodiesel provided significant reduction in CO, HC, NO_x and smoke under speed characteristic at full engine load. Based on this study, biodiesel can be used as a substitute for diesel in diesel engine.     

Modeling and prediction of NOx emission in an LPG–diesel dual-fuel CI engine

Different alternative fuels have been proposed by various researchers in diesel engines in view of increased NO_x and particulate emissions. Out of the various methods proposed, dual fueling is one of the most important techniques that helps solve the different operational problems related to diesel engine combustion and emission. In the current study, modeling and predicting the formation of NO_x emission in a duel fuel liquefied petroleum gas (LPG)–diesel engine has been undertaken. Simulations have been conducted for various LPG flow rates at different engine loads and the predicted NO_x values are compared with the experimental values. The results found that there is a decent agreement between the forecasted and the investigational results, where the average difference is within 13.7%. Furthermore, it is found that minimum NO_x emission was observed for an LPG flow rate in the range of 0.4–0.6 kg/h and when the engine is running with 75% loading.     

A study on the effect of hydrogen enriched intake air on the characteristics of a diesel engine fueled with ethanol blended diesel

This work aims to replace conventional diesel fuel with low and no carbon fuels like ethanol and hydrogen to reduce the harmful emission that causes environmental degradation. Pursuant to this objective, this study investigated the performance, combustion, and emission characteristics of the diesel engine operated on dual fuel mode by ethanol-diesel blends with H₂ enriched intake air at different engine loads with a constant engine speed of 1500 rpm. The results were compared to sole diesel operation with and without H₂ enrichment. The ethanol/diesel was blended in v/v ratios of 5, 10, and 15% and tested in a diesel engine along with a 9 lpm H₂ flow rate at the intake manifold. The results revealed that 10% ethanol with 9 lpm H₂ combination gives the maximum brake thermal efficiency, which is 1% and 4.8% higher than diesel with and without H₂ enrichment, respectively. The brake specific fuel consumption of the diesel-ethanol blends with H₂ flow increased with increasing ethanol ratio in the blend. When the ethanol ratio increased from 5 to 10%, in-cylinder pressure and heat release rate were increased, whereas HC, CO, and NO_x emissions were decreased. At maximum load, the CO and HC emission of 10% ethanol blend with 9 lpm H₂ case decreased by about 50% and 28.7% compared to sole diesel. However, NO_x emission of the same blend was 11.4% higher than diesel. From the results, the study concludes that 10% ethanol blended diesel with a 9 lpm H₂ flow rate at the intake port is the best dual-fuel mode combination that gives the best engine characteristics with maximum diesel replacement.     

Application of exhaust gas fuel reforming in diesel and homogeneous charge compression ignition (HCCI) engines fuelled with biofuels

This paper documents the application of exhaust gas fuel reforming of two alternative fuels, biodiesel and bioethanol, in internal combustion engines. The exhaust gas fuel reforming process is a method of on-board production of hydrogen-rich gas by catalytic reaction of fuel and engine exhaust gas. The benefits of exhaust gas fuel reforming have been demonstrated by adding simulated reformed gas to a diesel engine fuelled by a mixture of 50% ultra low sulphur diesel (ULSD) and 50% rapeseed methyl ester (RME) as well as to a homogeneous charge compression ignition (HCCI) engine fuelled by bioethanol. In the case of the biodiesel fuelled engine, a reduction of NO_x emissions was achieved without considerable smoke increase. In the case of the bioethanol fuelled HCCI engine, the engine tolerance to exhaust gas recirculation (EGR) was extended and hence the typically high pressure rise rates of HCCI engines, associated with intense combustion noise, were reduced.     

Experimental investigation on a DI dual fuel engine with hydrogen injection

Over the past two decades considerable efforts have been undertaken to develop and introduce new alternative fuels for the conventional gasoline and diesel. Many alternative fuels, both liquid and gaseous, have been experimented and some have even been commercialized such as ethanol, natural gas, etc. Hydrogen has been considered as an excellent fuel to replace the petroleum‐based fuels due to its clean burning characteristics. In the present experimental investigation, hydrogen was injected in the intake manifold and diesel fuel was injected inside the engine cylinder in the conventional manner. Hydrogen injection parameters such as injection timing, injection duration and quantity of hydrogen injected were optimized based on the performance and emission characteristics. Exhaust gas recirculation (EGR) technique was adopted to reduce the oxides of nitrogen emission. From the results it was observed that for hydrogen diesel dual fuel (DF) engine, the optimal operating parameters for hydrogen injection were start of injection at gas exchange top dead centre with injection duration of 30° crank angle with the hydrogen flow rate of 7.5 litres per minute (lpm). With EGR the optimized condition was found to be 20% for the entire load. The brake thermal efficiency with 20% EGR increases by 16% at 75% load as compared with diesel, while at full load it reduces by 8% due to the recirculation of exhaust gases that results in a reduction of intake oxygen concentration compared with part load. NO_X emission decreases by five and half times, while other emissions increase by 1.4 times as compared with DF engine. Copyright © 2008 John Wiley & Sons, Ltd.     

Emission and performance estimation in hydrogen injection strategies on diesel engines

Recently, the increasing demand for energy requires the use of alternative fuels, especially in fossil fueled power systems. As a promising alternative fuel for next-generation diesel engines that utilize fossil fuel, hydrogen fuel is one step ahead due to its positive properties. In this study, the effects of hydrogen on the performance of a diesel engine have been numerically investigated with respect to different injection ratios and timings. The numerical results of the study for 25% load conditions on a single-cylinder, four-stroke diesel engine have been validated against experimental data taken from literature and good agreement has been observed for pressure results. Emission parameters such as NO_x, CO and performance parameters such as cylinder temperature, pressure, power, thermal efficiency and IMEP are presented comparatively.The results of numerical analyses show that the maximum pressure, temperature and heat release rate are observed with injection ratio of H15 and early injection timing (20° CA BTDC). Besides that, engine power, thermal efficiency and IMEP are greatly improved with increasing injection ratio and early injection timing. Although combustion chamber performance parameters improve with rising the hydrogen injection ratio, higher NO_x emissions have also been detected as a negative side effect. Furthermore, while early injection timing increases diesel engine performance, it also causes an increase in NO_x emissions. Therefore, precise determination of injection timing together with the optimum amount of hydrogen has revealed that it brings crucial improvement in engine performance and emissions.     

Effect of hydrogen enrichment and TiO2 nanoparticles on waste cooking palm biodiesel run CRDI engine

In this study, we deal with the production and utilization of waste-cooking palm biodiesel (WCB) and.evaluated the influence of the addition of titanium dioxide (TiO₂) nanoparticles in hydrogen-enriched single-cylinder CRDI diesel engine. XRD, SEM, and EDX decide the structure and morphology of TiO₂ nanoparticles. The TiO₂ nanoparticles were dispersed in the tested fuels at a dosage of 50–75 ppm with the aid of ultra-sonication. Based on the oxidation stability study, the B20 + 75 ppm (TiO₂) fuel blend is the pilot fuel for the engine test. Further, the engine is enriched with a hydrogen (H₂) flow of 10 lpm. Results revealed that the performance parameters were improved with the addition of H₂ enrichment and TiO₂ nanoparticles compared to D. The brake thermal efficiency of the engine was improved by 8.21%. In comparison, brake-specific fuel consumption decreased by 42.86%. Furthermore, adding nanoparticles also reduced CO and HC emissions by 74% and 27.27%, respectively, whereas the NO_x emission was slightly increased. Thus, the findings demonstrated that hydrogen-enriched nanoparticles added to biodiesel might be considered a substitute for fossil fuels and report a positive impact on diesel engine performance without requiring significant modifications.     

Hydrogen enriched waste oil biodiesel usage in compression ignition engine

In the present study, hydrogen enrichment for biodiesel-diesel blends was evaluated to investigate the performance and emission characteristics of a compression ignition engine. Biodiesel was obtained from waste oil and blended to pure diesel fuel by volume fraction of 0%, 10% and 20%. After that, pure hydrogen was introduced through the intake air at different flow rates. Effects of pure hydrogen on performance and emission characteristics were investigated by evaluating power, torque, specific fuel consumption, CO, CO₂ and NO_x emissions. Experimental study revealed that waste oil biodiesel usage deteriorated performance and emission parameters except CO emissions. However, the enrichment test fuels with hydrogen fuel can improve performance characteristics and emission parameters, whereas it increased NO_x emissions. Brake thermal efficiency and specific fuel consumption were improved when the test fuels enriched with hydrogen gas. Because of absence of carbon atoms in the chemical structure of the hydrogen fuel, hydrogen addition dropped CO and CO₂ emissions but increment in cylinder temperature caused rising in NO_x emissions.