Sc2O3超细粉均相沉淀法的制备及表征

以(NH4)SO4为沉淀剂和分散剂,Sc(NO4)3为母盐,采用均相沉淀法合成了片状的碱式硫酸钪前驱沉淀物[Sc(OH)SO4].通过差热/热重分析了前驱体的热分解过程,并结合红外光谱、X-射线衍射、透射电镜联用X-射线光电子能谱等测试手段研究了前躯体及煅烧产物的成分、性质.结果表明,由该法制备出的Sc2O3超细粉具有纯度较高、颗粒粒度小(100 nm)、粒度分布均匀、分散性好、近似球形的优异性能.通过水洗-乙醇清洗-丙酮搅拌,结合超声-室温干燥-湿磨等方式处理,对粉体分散性的提高均起到了重要的作用.     

湿化学法制备 Y2O3纳米粉及透明陶瓷

以Y(NO3)3溶液和NH3·H2O为原料,制备了Y2O3纳米粉体.先驱沉淀物的化学组成为Y2(OH)5NO3·H2O.研究了pH值及滴加过程对先驱沉淀物形貌及Y2O3产物烧结性的影响.正向滴定,pH值较低时(pH=7.9),先驱沉淀物为片状结构;pH值较高时(pH=10.0),先驱沉淀物片层状结构特性减轻,并且颗粒变的细小.反向滴加时,片层状结构特征消失,主要为块状晶粒.先驱沉淀物为片状结构时,得到的粉体活性较高.添加适量的(NH4)2SO4能够减轻Y2O3粉体的团聚,沉淀的同时控制pH值在9以下,所得到的粉体具有更好的烧结性能.采用得到的Y2O3纳米粉,不加入任何烧结助剂,经1700℃真空烧结4h得到了透明Y2O3陶瓷.     

液相法制备Ni3S4纳米粉

以NiSO4·6H2O和Na2S2O4·2H2O为原料,采用液相法室温合成了Ni3S4纳米粉.考察了影响粉体质量的各种因素,获得了最佳工艺条件,并对制备的纳米粉采用TEM、XRD和络合分析等方法进行了表征.结果表明:本法制备的Ni3S4纳米粉呈尖晶石型、平均粒径为10nm、粒度分布窄、分散性好、纯度高、转化率高.     

均相沉淀法制备掺钕钇铝石榴石(Nd∶YAG)纳米粉末

采用均相沉淀法,以Al(NO3)3.9H2O、Y2O3、Nd2O3、(NH4)2SO4和NH4HCO3为原料,正硅酸乙酯为添加剂,制备Nd∶YAG纳米粉末;并探讨了均相沉淀法制备Nd∶YAG纳米粉末的反应机理。研究结果表明,粉体在800℃时为无定型态,当温度达到900℃时析出大量YAlO3(YAP)和少量Y3Al5O12(YAG)晶体,当温度达到1000℃时就全部转化为YAG立方晶相;混合溶液生成沉淀物是由Al 3+的沉淀所决定的;Al 3+首先均相成核,随后Y3+和Nd3+以Al沉淀物为异相核发生异相成核,形成的沉淀物覆着于Al沉淀物表面,推测沉淀物结构可能为钇包覆铝的核壳结构。     

化学沉淀法制备锂离子电池正极材料LiFePO4

以LiOH·H2O、(NH4)2HPO4、FeSO4·7H2O为原料,通过沉淀法制备锂离子电池正极材料LiFePO4前驱体,前躯体中混入2wt%的活性炭在550℃(2烧结6h得到橄榄石型的LiFePO4.研究了反应时间、烧结温度、烧结时间对合成LiFePO4的影响,利用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、热重-差热综合分析(TG-DTA)、红外光谱(FTIR)等手段对合成的LiFePO4的结构、形态、热化学性质和电化学性能进行了研究,结果表明化学沉淀法制备橄榄石型LiFePO4正极材料呈形貌规整的类球形颗粒,晶型发育完善,粒度分布均匀.LiFePO4样品在室温首次放电容量119.5mAb·g-1,8次循环后放电容量衰减低于2%.     

液氨沉淀法制备ZnO超微粉

以Zn(NO3 ) 2 为原料 ,NH3 ·H2 O为沉淀剂 ,采用直接沉淀法制备Zn(OH) 2 白色沉淀 ,经洗涤、干燥、煅烧后生成ZnO超微粉末。通过TEM观察到ZnO为球形晶体 ,平均粒径 15 0nm。探讨了溶液pH值、沉淀剂浓度、反应时间、反应温度对前躯体Zn(OH) 2 粒度的影响以及煅烧过程中煅烧温度与煅烧时间对ZnO粒度的影响 ,得出了最佳工艺条件。     

低温陈化法制备纳米ZrO2及条件对粒径的影响

为了制得可控粒径的ZrO2粉并提高其均匀性,采用低温陈化法合成了ZrO2纳米粉,并讨论了反应条件对样品粒径的影响.通过DTA,XRD,TEM和粒度分布仪等检测手段对产品进行了表征.结果表明:在500℃得到了晶化较好的单斜相ZrO2,选择适当的合成条件:控制Zr4+与CO(NH2)2的摩尔比为1∶3,溶液pH为1.5,加入少量聚乙二醇800(PEG-800),可得到粒度分布集中,均匀性较好,粒径约为24.4 nm的样品.该法工艺简单、得到的ZrO2粉体粒径分布较窄.     

α-Al2O3籽晶对Al2O3晶型转变及形貌的影响

在湿化学法合成的纳米Al2O3前驱体NH4Al(0H)2CO3中添加α-Al2O3籽晶(150nm左右)，研究了α-Al2O3籽晶对Al2O3晶型转变及形貌的影响．结果表明，少量Q—A1203籽晶的添加能降低形核温度，有效的提高相转变速率，在较低的温度下完成θ→α-Al2O3的相转变，同时对聚合生长也产生一定的影响．     

Na0.5Bi0.5TiO3纳米纤维的制备及形成机理研究

以Bi(NO3)3 5H2O、板状钛酸(H1.07Ti1.73O4 nH2O)、NaOH为原料,采用水热法合成了具有钙钛矿结构的Na0.5Bi0.5TiO3纳米纤维.利用X射线衍射仪(XRD)、场发射扫描电镜(FESEM)、透射电镜(TEM)和X射线能谱仪(EDS)对产物进行表征.通过考察在200℃下水热反应不同时间的产物的相结构、微观形貌及化学组成,对Na0.5Bi0.5TiO3纳米纤维的形成机理进行了探讨.结果表明:钛酸H1.07Ti1.73O4 nH2O是一类具有层板结构的化合物,在水热反应过程中,板状钛酸的层间H3O+可与Na+、Bi3+进行离子交换,通过原位生长的方式形成了板状Na0.5Bi0.5TiO3颗粒,随着水热反应的进行,板状Na0.5Bi0.5TiO3颗粒裂解形成纳米纤维.所得的Na0.5Bi0.5TiO3纳米纤维分散性好,具有钙钛矿结构,直径为30~150 nm,长度为几个微米到十几个微米.     

Al3Ti/TiN复合纳米粉的制备及表征

采用氢等离子体-金属反应法(HPMR)在Ar∶H2∶N2=1.0∶1.0∶0.2的气氛下,制备Al3Ti/TiN复合纳米粉。利用X射线衍射仪(XRD)、透射电镜(TEM)、氢氧气体仪、ICP光谱仪和激光粒度仪研究粉末的形貌、组成及粒度分布,分析了纳米粉表面成分。发现纳米粉中主要成分为近球形的Al3Ti和立方体的TiN,平均粒度约为120 nm,Al3Ti和TiN颗粒分布均匀,两相颗粒间相互粘连。近球形的Al3Ti颗粒表面包覆非晶态的Al2O3层,形成核壳结构。TiN颗粒保持立方结构的惯态,纳米粉中含有少量的TiO2吸附的氧。钝化后的复合纳米粉体具有良好的稳定性。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...