A 14-GHz 256/257 dual-modulus prescaler with secondary feedback and its application to a monolithic CMOS 10.4-GHz phase-locked loop

A 14-GHz 256/257 dual-modulus prescaler is implemented using secondary feedback in the synchronous 4/5 divider on a 0.18-/spl mu/m foundry CMOS process. The dual-modulus scheme utilizes a 4/5 synchronous counter which adopts a traditional MOS current mode logic clocked D flip-flop. The secondary feedback paths limit signal swing to achieve high-speed operation. The maximum operating frequency of the prescaler is 14 GHz at V/sub DD/=1.8 V. Utilizing the prescaler, a 10.4-GHz monolithic phase-locked loop (PLL) is demonstrated. The voltage-controlled oscillator (VCO) operates between 9.7-10.4 GHz. The tuning range of the VCO is 690 MHz. The phase noise of the PLL and VCO at a 3-MHz offset with I/sub vco/=4.9 mA is -117 and -119 dBc/Hz, respectively. At the current consumption of I/sub vco/=8.1 mA, the phase noise is -122 and -122 dBc/Hz, respectively. The PLL output phase noise at a 50-kHz offset is -80 dBc/Hz. The PLL consumes /spl sim/31 mA at V/sub DD/=1.8 V.     

Design of wide-band CMOS VCO for multiband wireless LAN applications

In this paper, a general design methodology of low-voltage wide-band voltage-controlled oscillator (VCO) suitable for wireless LAN (WLAN) application is described. The applications of high-quality passives for the resonator are introduced: 1) a single-loop horseshoe inductor with Q > 20 between 2 and 5 GHz for good phase noise performance; and 2) accumulation MOS (AMOS) varactors with C/sub max//C/sub min/ ratio of 6 to provide wide-band tuning capability at low-voltage supply. The adverse effect of AMOS varactors due to high sensitivity is examined. Amendment using bandswitching topology is suggested, and a phase noise improvement of 7 dB is measured to prove the concept. The measured VCO operates on a 1-V supply with a wide tuning range of 58.7% between 3.0 and 5.6 GHz when tuned between /spl plusmn/0.7 V. The phase noise is -120 dBc/Hz at 3.0 GHz, and -114.5 dBc/Hz at 5.6 GHz, with the nominal power dissipation between 2 and 3 mW across the whole tuning range. The best phase noise at 1-MHz offset is -124 dBc/Hz at the frequency of 3 GHz, a supply voltage of 1.4 V, and power dissipation of 8.4 mW. When the supply is reduced to 0.83 V, the VCO dissipates less than 1 mW at 5.6 GHz. Using this design methodology, the feasibility of generating two local oscillator frequencies (2.4-GHz ISM and 5-GHz U-NII) for WLAN transceiver using a single VCO with only one monolithic inductor is demonstrated. The VCO is fabricated in a 0.13-/spl mu/m partially depleted silicon-on-insulator CMOS process.     

Large-signal analysis of MOS varactors in CMOS -G/sub m/ LC VCOs

MOS varactors are used extensively as tunable elements in the tank circuits of RF voltage-controlled oscillators (VCOs) based on submicrometer CMOS technologies. MOS varactor topologies include conventional D = S = B connected, inversion-mode (I-MOS), and accumulation-mode (A-MOS) structures. When incorporated into the VCO tank circuit, the large-signal swing of the VCO output oscillation modulates the varactor capacitance in time, resulting in a VCO tuning curve that deviates from the dc tuning curve of the particular varactor structure. This paper presents a detailed analysis of this large-signal effect. Simulated results are compared to measurements for an example 2.5-GHz complementary -G/sub m/ LC VCO using I-MOS varactors implemented in 0.35-/spl mu/m CMOS technology.     

5-GHz CMOS LC VCOs with wide tuning ranges

A 4.8-GHz LC voltage-controlled oscillator (VCO) optimized for maximum tuning range was designed and fabricated using 0.25-/spl mu/m 1P5M CMOS process. The optimized design used an inverse proportionality between the two parasitic capacitances of the inductor and the MOS transistors for minimizing the parasitic capacitance at the oscillation node. The fabricated LC VCO has a wide tuning range of 20.3% from 4.32 GHz to 5.3 GHz with a power dissipation of 7.3 mW. This tuning range performance is comparable to, or better than, those of the reported CMOS LC VCOs in 5-GHz band. The measured phase noise is -82 dBc/Hz and -114.6 dBc/Hz at 100 KHz and 1-MHz offset, respectively.     

A 243-GHz F/sub t/ and 208-GHz F/sub max/, 90-nm SOI CMOS SoC technology with low-power mm-wave digital and RF circuit capability

A 90-nm silicon-on-insulator (SOI) CMOS system on-chip integrates high-performance FETs with 243-GHz F/sub t/, 208-GHz F/sub max/, 1.45-mS//spl mu/m gm, and sub 1.1-dB NFmin up to 26 GHz. Inductor Q of 20, VNCAP of 1.8-fF//spl mu/m/sup 2/, varactor with a tuning range as high as 25:1, and a low-loss microstrip. Transmission lines were successfully integrated without extra masks and processing steps. SOI and its low parasitic junction capacitance enables this high level of performance and will expand the use of CMOS for millimeter-wave applications.     

A 5-GHz low phase noise differential colpitts CMOS VCO

A low noise 5-GHz differential Colpitts CMOS voltage-controlled oscillator (VCO) is proposed in this letter. The Colpitts VCO core adopts only PMOS in a 0.18-/spl mu/m CMOS technology to achieve a better phase noise performance since PMOS has lower 1/f noise than NMOS. The VCO operates from 4.61 to 5 GHz with 8.3% tuning range. The measured phase noise at 1-MHz offset is -120.42 dBc/Hz at 5 GHz and -120.99 dBc/Hz at 4.61 GHz. The power consumption of the VCO core is only 3 mW. To the authors' knowledge, this differential Colpitts CMOS VCO achieves the best figure of merit (FOM) of 189.6 dB at 5-GHz band.     

On the feasibility of CMOS multiband phase shifters for multiple-antenna transmitters

We present the design of an integrated multiband phase shifter in RF CMOS technology for phased array transmitters. The phase shifter has an embedded classical distributed amplifier for loss compensation. The phase shifter achieves a more than 180/spl deg/ phase tuning range in a 2.4-GHz band and a measured more than 360/spl deg/ phase tuning range in both 3.5-GHz and 5.8-GHz bands. The return loss is less than -10dB at all conditions. The feasibility for transmitter applications is verified through measurements. The output power at a 1-dB compression point (P/sub 1 dB/) is as high as 0.4dBmat 2.4GHz. The relative phase deviation around P/sub 1 dB/ is less than 3/spl deg/. The design is implemented in 0.18-/spl mu/mRF CMOS technology, and the chip size is 1200/spl mu/m /spl times/ 2300 /spl mu/m including pads.     

A low-voltage 40-GHz complementary VCO with 15% frequency tuning range in SOI CMOS technology

The design of a low-voltage 40-GHz complementary voltage-controlled oscillator (VCO) with 15% frequency tuning range fabricated in 0.13-/spl mu/m partially depleted silicon-on-insulator (SOI) CMOS technology is reported. Technological advantages of SOI over bulk CMOS are demonstrated, and the accumulation MOS (AMOS) varactor limitations on frequency tuning range are addressed. At 1.5-V supply, the VCO core and each output buffer consumes 11.25 mW and 3 mW of power, respectively. The measured phase noise at 40-GHz is -109.73 dBc/Hz at 4-MHz offset from the carrier, and the output power is -8 dBm. VCO performance using high resistivity substrate (/spl sim/300-/spl Omega//spl middot/cm) has the same frequency tuning range but 2 dB better phase noise compared with using low resistivity substrate (10 /spl Omega//spl middot/cm). The VCO occupies a chip area of only 100 /spl mu/m by 100 /spl mu/m (excluding pads).     

A fully integrated 5.8 GHz U-NII band 0.18-/spl mu/m CMOS VCO

A fully integrated 5.8 GHz CMOS L-C tank voltage-controlled oscillator (VCO) using a 0.18-/spl mu/m 1P6M standard CMOS process for 5 GHz U-NII band WLAN application is presented. The VCO core circuit uses only PMOS to pursue a better phase noise performance since it has less 1/f noise than NMOS. The measurement is performed by using a FR-4 PCB test fixture. The output frequency of the VCO is from 5860 to 6026 MHz with a 166 MHz tuning range and the phase noise is -96.9 dBc/Hz at 300 kHz (or -110 dBc/Hz at 1 MHz) with V ctrl = 0 V. The power consumption of the VCO excluding buffer amplifiers is 8.1 mW at V/sub DD/ = 1.8 V and the output power is -4 dBm.     

A 0.83-2.5-GHz continuously tunable quadrature VCO

A quadrature VCO with /spl plusmn/50% continuous 0.83-2.5-GHz tuning range is presented. It is based on a core LC-QVCO with /spl plusmn/20% tuning range, a single sideband mixer (SSBM), two frequency dividers and a multiplexer. The circuit has been implemented in a 0.13-/spl mu/m 1.2-V CMOS technology. The additional area with respect to the core LC-QVCO is 100 /spl mu/m/spl times/100 /spl mu/m. Quadrature error is less than 2/spl deg/; the phase noise is less than -120 dBc/Hz @ 1 MHz over the whole tuning range and is mainly due to the LC-QVCO. Spurs are more than 34 dB below the fundamental in the worst case.     

A 1.3-V 5-mW fully integrated tunable bandpass filter at 2.1 GHz in 0.35-/spl mu/m CMOS

A 2.1-GHz 1.3-V 5-mW fully integrated Q-enhancement LC bandpass biquad programmable in f/sub o/, Q, and peak gain is implemented in 0.35-/spl mu/m standard CMOS technology. The filter uses a resonator built with spiral inductors and inversion-mode pMOS capacitors that provide frequency tuning. The Q tuning is through an adjustable negative-conductance generator, whereas the peak gain is tuned through an input G/sub m/ stage. Noise and nonlinearity analyses presented demonstrate the design tradeoffs involved. Measured frequency tuning range around 2.1 GHz is 13%. Spiral inductors with Q/sub o/ of 2 at 2.1 GHz limit the spurious-free dynamic range (SFDR) at 31-34 dB within the frequency tuning range. Measurements show that the peak gain can be tuned within a range of around two octaves. The filter sinks 4 mA from a 1.3-V supply providing a Q of 40 at 2.19 GHz with a 1-dB compression point dynamic range of 35 dB. The circuit operates with supply voltages ranging from 1.2 to 3 V. The silicon area is 0.1 mm/sup 2/.     

A 1.8-V 2.4/5.15-GHz dual-band LCVCO in 0.18-/spl mu/m CMOS technology

A dual band, fully integrated, low phase-noise and low-power LC voltage-controlled oscillator (VCO) operating at the 2.4-GHz industrial scientific and medical band and 5.15-GHz unlicensed national information infrastructure band has been demonstrated in an 0.18-/spl mu/m CMOS process. At 1.8-V power supply voltage, the power dissipation is only 5.4mW for a 2.4-GHz band and 8mW for a 5.15-GHz band. The proposed VCO features phase-noise of -135dBc/Hz at 3-MHz offset frequency away from the carrier frequency of 2.74GHz and -126dBc/Hz at 3-MHz offset frequency away from 5.49GHz. The oscillator is tuned from 2.2 to 2.85GHz in the low band (2.4-GHz band) and from 4.4 to 5.7GHz in the high band (5.15-GHz band).     

A 2 V 1.8 GHz fully integrated CMOS dual-loop frequency synthesizer

A 2 V 1.8 GHz fully integrated CMOS dual-loop frequency synthesizer is designed in a standard 0.5 /spl mu/m digital CMOS process for wireless communication. The voltage-controlled oscillator (VCO) required for the low-frequency loop is designed using a ring-type VCO and achieves a tuning range of 89% from 356 to 931 MHz and a phase noise of -109.2 dBc/Hz at 600 kHz offset from 856 MHz. With an active chip area of 2000/spl times/1000 /spl mu/m/sup 2/ and at a 2 V supply voltage, the whole synthesizer achieves a tuning range from 1.8492 to 1.8698 GHz in 200 kHz steps with a measured phase noise of -112 dBc/Hz at 600 kHz offset from 1.86 GHz. The measured settling time is 128 /spl mu/s and the total power consumption is 95 mW.     

A 5.7-GHz 0.18-/spl mu/m CMOS gain-controlled differential LNA with current reuse for WLAN receiver

This letter presents a 5.7 GHz 0.18 /spl mu/m CMOS gain-controlled differential LNA for an IEEE 802.11a WLAN application. The differential LNA, fabricated with the 0.18 /spl mu/m 1P6M standard CMOS process, uses a current-reuse technology to increase linear gain and save power consumption. The circuit measurement is performed using an FR-4 PCB test fixture. The LNA exhibits a noise figure of 3.7 dB, linear gain of 12.5 dB, P/sub 1dB/ of -11 dBm, and gain tuning range of 6.9 dB. The power consumption is 14.4 mW at V/sub DD/=1.8 V.     

Time-based frequency band selection method for phase-locked loops

High-performance phase-locked loops (PLLs) often require voltage-controlled oscillators (VCOs) employing both discrete and continuous tuning mechanisms to satisfy a wide frequency range and a low VCO tuning gain simultaneously. An auxiliary circuit is required to facilitate the selection among a group of discrete bands. An agile technique to search for an optimum VCO frequency band is proposed. The search is based on measuring the period difference between a reference and the VCO-divided signals. The VCO band selection circuit is implemented with a 10 GHz PLL in a 0.18 /spl mu/m CMOS process and consumes only an extra 3 mA. The band selection time is less than 4 /spl mu/s.     

9.3-10.4-GHz-band cross-coupled complementary oscillator with low phase-noise performance

A fully integrated 10-GHz-band voltage-controlled oscillator (VCO) has been designed and fabricated using commercial 0.18-/spl mu/m CMOS technology. The complementary cross-coupled differential topology is adopted in the design. The measured phase-noise is around -89 dBc/Hz at the offset frequency of 100 kHz from the center frequency of 9.83 GHz, the output frequency tuning range of the fabricated VCO is 1.1 GHz ranging from 9.3 to 10.4 GHz, and the power consumption of the core VCO circuit is 5.8 mW. The design is the first one that adopts the complementary cross-coupled circuit structure for 10-GHz-band oscillators, and whose performances of the VCO are the best ones for 10-GHz-band oscillators, compared with the 10-GHz-band CMOS oscillators reported earlier.     

Low phase noise IP VCO for multistandard communication using a 0.35-/spl mu/m BiCMOS SiGe technology

In this letter, we report that a commonly used 0.35-/spl mu/m, 60-GHz-F/sub MAX/ BiCMOS SiGe monolithic microwave integrated circuit (MMIC) technology is able to provide very low phase noise signal generation in the X-band frequency range. This statement has been demonstrated using a differential LC voltage-controlled oscillator (VCO) in which varactors are realized with metal-oxide semiconductor (MOS) transistors and inductors with a patterned ground shield technology. This VCO features an output power signal in the range of -5 dBm and exhibits a phase noise of -96 dBc/Hz at a frequency offset of 100kHz from carrier and -120 dBc/Hz at a frequency offset of 1 MHz. The VCO features a tuning range of 430 MHz or 4.3% of its operating frequency. Its power consumption is in the range of 70 mW (200 mW with buffers circuits) for a chip size of 800/spl times/1000 /spl mu/m/sup 2/ (including RF probe pads).     

A high f/sub OSC//f/sub T/ ratio VCO in SiGe BiCMOS technology

A 37-GHz voltage controlled oscillator (VCO) fabricated in IBM's 47-GHz SiGe BiCMOS technology is presented. The VCO achieves a phase noise of -81dBc/Hz at 1-MHz offset from the carrier while delivering an output power of -30dBm to 50 /spl Omega/ buffers. Drawing 15-mA of dc current from a 3-V power supply the VCO occupies 350/spl mu/m/spl times/280/spl mu/m of silicon area. Capacitive emitter degeneration and compact layout are used to achieve high f/sub OSC//f/sub T/ ratio.     

A compact 43-GHz monolithic differential VCO in 0.5-/spl mu/m InP DHBT technology

A compact monolithic integrated differential voltage controlled oscillator (VCO) using 0.5-/spl mu/m emitter width InP/InGaAs double-heterostructure bipolar transistors with a total chip size of 0.42 mm /spl times/ 0.46 mm is realized by using cross-coupled configuration for extremely high frequency satellite communications system applications. The device performance of F/sub max/ greater than 320 GHz at a current density of 5 mA//spl mu/m/sup 2/ and 5-V BVceo allows us to achieve a low phase noise 42.5-GHz fundamental VCO with -0.67-dBm output power. The VCO exhibits the phase noise of -106.8 dBc/Hz at 1-MHz offset and -122.3 dBc/Hz at 10-MHz offset from the carrier frequency.     

A low-phase-noise K-band CMOS VCO

A novel circuit topology for low-phase-noise voltage controlled oscillators (VCOs) is presented in this letter. By employing a PMOS cross-coupled pair with a capacitive feedback, superior circuit performance can be achieved especially at higher frequencies. Based on the proposed architecture, a prototype VCO implemented in a 0.18-/spl mu/m CMOS process is demonstrated for K-band applications. From the measurement results, the VCO exhibits a 510-MHz frequency tuning range at 20GHz. The output power and the phase noise at 1-MHz offset are -3dBm and -111dBc/Hz, respectively. The fabricated circuit consumes a dc power of 32mW from a 1.8-V supply voltage.