基于电力载波通信的DALI系统应用研究

针对DALI系统双线差分信号的通信方式,对于采用传统照明的场所进行升级改造存在再次布线的问题,提出了在不改变电力线的基础上,以电力线作为DALI系统的通信介质,使DALI系统与电力载波通信相兼容。然而,由于载波信号的高衰减特性,使DALI系统在电力线上的传输受到了限制。对此,通过研究泛洪路由控制策略,解决了通信距离的问题,实现了以电力线为传输介质的DALI照明系统。系统测试证明,路由组网灵活,系统性能稳定、可靠。     

Energy efficient bidirectional relay network with spatial modulation

S patial modulation is a potential candidate for 5G wireless communication systems that provides high spectral efficiency with high reliability and low complexity. Spatial modulation conveys information in the index of transmitting antenna along with conventional modulation scheme. Also, energy efficiency communication plays a vital role in 5G wireless communication. In this article, energy efficiency and spectral efficiency are focused on a bidirectional relay network. In the proposed bidirectional relay network, the energy consumption burden at the relay node is reduced by placing a power splitter that coordinates the energy harvesting and information processing at the relay node. Spatial modulation is employed at all nodes to reduce the effect of interchannel interference and synchronization problem in the receiver. The combined effect of spatial modulation in all nodes and energy harvest at the relay node are analyzed in the bidirectional relay network. The end‐to‐end outage probability expression for the bidirectional relay network is derived in terms of power splitting factor at relay node. Analytical simulation results have been verified by Monte‐Carlo simulations. The overall performance of the proposed system is compared with an existing literature and found that the proposed system is having better spectral efficiency and energy harvesting.     

一种高效低时延的宽带电力线通信网多跳MAC协议

针对IEEE1901.1宽带电力线通信媒体接入控制(Medium Access Control,MAC)协议涉及到信标时隙利用不充分和控制开销过大等问题,提出了一种高效低时延的宽带电力线通信网多跳MAC协议(Efficient and Low Delay Multi-hop MAC,ELDM-MAC).采用基于节点层级...     

无线传感网两种中继选择策略的中断概率分析

无线传感网发射功率受限,采用中继通信的方式可以扩展通信覆盖区域,中继选择是其关键技术之一。不同的中继选择策略会对中断概率产生不同的影响,其一是选择候选集合中的所有节点作为中继节点,其二是选择候选节点中的信噪比最大的节点作为中继节点。为了比较这两种中继选择策略的性能,推算了两种策略下的中断概率闭合表达式,并进行数值分析。结果表明,在不考虑功耗平衡的前提下,策略二的性能优于策略一。     

能量收集多跳D2D无线传感网络中的中继选择算法

针对无线功率传输技术的能量收集效率有限造成信噪比下降进而引发通信中断率增加的问题,在能量收集多跳D2D(Device to Device)无线传感网络中,提出一种基于改进K-means聚类的中继选择方法。首先,推导得到能量收集下的信噪比因子,使其作为K-means聚类特征。然后,利用最小欧氏距离原则得到距离聚类中心最近的实际节点的位置。最后,根据距离重排序得到中继节点,形成从源节点到目的节点的通信链路。仿真实验结果表明,相比最短路径算法和随机中继协作方案,所提出的改进算法链路信噪比更大,能够减小通信中断率,具有更好的中继性能。     

Hybrid channel estimation for MIMO relay systems with Doppler offset influences

The design of the channel estimation method in a multiple‐input multiple‐output (MIMO) relay system plays a highly crucial role in deciding the overall system performance. For the realistic scenarios specifically, with fast time‐varying channel conditions due to highly mobile communicating nodes, the degree of accuracy to which the channel estimates are obtained for MIMO relay systems influences the communication system reliability significantly. However, most of the channel estimation approaches proposed in literature for MIMO relay systems assume that the Doppler offset contributed by highly mobile nodes is already known to the receiver, ignoring the resulting nonlinear system dynamics. Hence, a novel hybrid algorithm is proposed to address the issue of time‐varying channel estimation under fast‐fading channel condition with Doppler offset influences contributed by high‐mobility communicating nodes for a 1‐way 2‐hop MIMO amplify‐and‐forward relaying system. The problem is first formulated as a nonlinear state‐space model, and then an algorithm is developed to estimate the individual source‐to‐relay and relay‐to‐destination channels in the presence of the associated dynamic Doppler offset. In the proposed method, a set of superimposed orthogonal pilots is used for aiding in the updation of the channel gains, since Kalman filter–based updation may lead to accumulation of estimation and prediction error. A detailed computational complexity analysis of the proposed hybrid algorithm is presented, which shows that the algorithm has moderate computational complexity with a good performance in fast time‐varying channel conditions with high node mobility in a dual‐hop MIMO relay system.     

基于中断概率的协作通信中继选择与功率分配算法

研究了功率受限情况下多中继协作通信网络的中继选择和功率优化问题。在AF网络中,提出了一种低复杂度中继选择与功率分配算法,其目标是在总功率一定的条件下使系统的中断概率最小。本算法对源节点和所有潜在中继节点进行功率分配,结合当前信噪比选择最优的中继集合,通过最速下降法求出使系统中断概率最低的功率分配因子。该算法不需要知道大量瞬时信道信息、不需要系统在等功率条件下进行中继选择,只需求得中继节点排列矩阵便可根据当前信噪比自适应获得最优中继节点集合。仿真结果表明,在相同条件下,该算法明显优于不同中继节点集合下几种算法的中断性能,并且与传统的SAF及AAF算法相比,有效降低了中断概率,提升了系统性能和功率效率。     

A multiple relay‐based medium access control protocol in multirate wireless ad hoc networks with multiple beam antennas

The advanced technique of multiple beam antennas is recently considered in wireless networks to improve the system throughput by increasing spatial reuse, reducing collisions, and avoiding co‐channel interference. The usage of multiple beam antennas is similar to the concept of Space Division Multiple Access (SDMA), while each beam can be treated as a data channel. Wireless networks can increase the total throughput and decrease the transmission latency if the physical layer of a mobile node can support multirate capability. Multirate wireless networks incurs the anomaly problem, because low data rate hosts may influence the original performance of high data rate hosts. In this work, each node fits out multiple beam antennas with multirate capability, and a node can either simultaneously transmit or receive multiple data on multiple beams. Observe that the transmitting or receiving operation does not happen at the same time. In this paper, we propose a multiple relay‐based medium access control (MAC) protocol to improve the throughput for low data rate hosts. Our MAC protocol exploits multiple relay nodes and helps the source and the destination to create more than one data channel to significantly reduce the transmission latency. Observe that low data rate links with long‐distance transmission latencies are distributed by multiple relay nodes, hence the anomaly problem can be significantly alleviated. In addition, the ACK synchronization problem is solved to avoid the condition that source nodes do not receive ACKs from destination nodes. An adjustment operation is presented to reduce unnecessary relay nodes during the fragment burst period. Finally, simulation results illustrate that our multiple relay‐based MAC protocol can achieve high throughput and low transmission latency. Copyright © 2009 John Wiley & Sons, Ltd.     

基于一致性算法的微网无功控制及延时算法优化

针对孤岛微电网中无功功率分配、通讯延时等问题,文中提出了一种基于一致性算法的分层控制算法。各分布式电源在时钟周期下与相邻的分布式电源交换电压信息,通过本地电压一致性算法得到全网平均电压值,可随迭代周期更新电压状态值,以实现各分布式电源无功功率的精确分配。电压一致性算法中,本地节点与相邻节点存在通讯延时,由微电网系统的拓扑结构可得到相邻节点间最大通讯延时时间,并由PI算法动态补偿延时误差。在MATLAB/Simulink平台搭建孤岛型微电网仿真模型,实验结果证明了控制策略的有效性。     

一种基于混合智能算法的协作中继选择新方法

针对多用户多中继场景下协作通信系统的中继选择问题,提出了一种基于混合智能算法的协作中继选择新方法。不同于现有的为每个源节点分配一个中继节点的中继选择方法,新方法建立了为每个源节点分配一个或多个中继节点的优化模型,以最大化多用户多中继协作系统的最小接收信噪比为优化目标,采用结合了模拟退火与遗传算法的混合智能算法来搜寻中继选择问题的最优解。仿真结果表明,所提方法可显著提高目的端的接收信噪比,且算法具有较强的全局搜索和快速寻优能力。     

Invincible AODV to detect black hole and gray hole attacks in mobile ad hoc networks

Today's communication world is majorly driven by mobile nodes that demand wireless systems for their data relay. One such network is mobile ad hoc network, which is a purely wireless network with which communication is feasible instantly without any aid of preexisting infrastructure; due to this magnificent feature, it has a wide variety of applications. Mobile ad hoc network hinges on cooperative nature of the mobile nodes for relaying data. But at the same time, nodes relaying data for others may compromise, leading to various security attacks. Two main security attacks that drastically bring down the performance of mobile ad hoc network are black hole and gray hole attacks. In this paper, we propose 2 versions of invincible Ad hoc On‐Demand Distance Vector protocol to detect black hole and gray hole nodes that have bypassed preventive mechanism during route discovery process. First is the basic version, which is based on node‐to‐node frame check sequence tracking mechanism, and second is the enhanced version, which is based on signed frame check sequence tracking mechanism. They create a deterrent environment addressing all kinds of black and gray hole attacks. They also provide reliable data transmission to all the nonmalicious nodes in the network by using end‐to‐end authentication mechanism. Simulation results show better performance in packet delivery ratio when compared with other contemporary solutions while addressing all kinds of black and gray hole attacks. It shows significant improvement in end‐to‐end delay and normalized routing load over Ad hoc On‐Demand Distance Vector under black hole or gray hole attacks and also shows better throughput and packet delivery ratio than the existing solution.     

Balance energy-efficient and real-time with reliable communication protocol for wireless sensor network

In many wireless sensor network applications, it should be considered that how to trade off the inherent conflict between energy efficient communication and desired quality of service such as real-time and reliability of transportation. In this paper, a novel routing protocols named balance energy-efficient and real-time with reliable communication (BERR) for wireless sensor networks (WSNs) are proposed, which considers the joint performances of real-time, energy efficiency and reliability. In BERR, a node, which is preparing to transmit data packets to sink node, estimates the energy cost, hop count value to sink node and reliability using local information gained from neighbor nodes. BERR considers not only each sender’ energy level but also that of its neighbor nodes, so that the better energy conditions a node has, the more probability it will be to be chosen as the next relay node. To enhance real-time delivery, it will choose the node with smaller hop count value to sink node as the possible relay candidate. To improve reliability, it adopts retransmission mechanism. Simulation results show that BERR has better performances in term of energy consumption, network lifetime, reliability and small transmitting delay.     

Resource allocations in relay‐assisted cellular networks

In a relay‐assisted cellular network, the transmission mode (either direct transmission or relaying) and the transmit power of the source and relay nodes affect not only transmission rates of individual links but also the rates of other links sharing the same channel. In this paper, we propose a cross‐layer design that jointly considers the transmission mode/relay node selection (MRS) with power allocation (PA) to optimize the system rate. We first formulate an optimization problem for a cellular system, where the same frequency channel can be reused in different cells. A low complexity heuristic MRS scheme is proposed on the basis of the link and interference conditions of the source and potential relay nodes. Given the transmission mode and relay node (if the relaying mode is chosen) of each link, the transmit power of the source and relay nodes can be solved by geometric programming. This method for MRS and PA can achieve a close‐to‐optimum performance, but implementing the PA requires heavy signalling exchanged among cells. To reduce the signalling overheads, we finally proposed a heuristic and distributed method for MRS and PA inspired by some asymptotic analysis. Numerical results are conducted to demonstrate the rate performance of the proposed methods.Copyright © 2013 John Wiley & Sons, Ltd.     

Optimal placement and routing strategies for resilient two‐tiered sensor networks

In hierarchical sensor networks using relay nodes, sensor nodes are arranged in clusters and higher powered relay nodes can be used as cluster heads. The lifetime of such a network is determined primarily by the lifetime of the relay nodes. In this paper, we propose two new integer linear programs (ILPs) formulations for optimal data gathering, which maximize the lifetime of the upper tier relay node network. Unlike most previous approaches considered in the literature, our formulations can generate optimal solutions under the non‐flow‐splitting model. Experimental results demonstrate that our approach can significantly extend network lifetime, compared to traditional routing schemes, for the non‐flow‐splitting model. The lifetime can be further enhanced by periodic updates of the routing strategy based on the residual energy at each relay node. The proposed rescheduling scheme can be used to handle single or multiple relay node failures. We have also presented a very simple and straightforward algorithm for the placement of relay nodes. The placement algorithm guarantees that all the sensor nodes can communicate with at least one relay node and that the relay node network is at least 2‐connected. This means that failure of a single relay node will not disconnect the network, and data may be routed around the failed node. The worst case performance of the placement algorithm is bounded by a constant with respect to any optimum placement algorithm. Copyright © 2008 John Wiley & Sons, Ltd.     

Trust establishment in cooperative wireless relaying networks

In cooperative wireless networks, relay nodes are employed to improve the performance of the network in terms of throughput and reliability. However, the presence of malicious relay nodes in the network may severely degrade the performance of the system. When a relay node behaves maliciously, there exists a possibility that such a node refuses to cooperate when it is selected for cooperation or deliberately drops the received packets. Trust establishment is a mechanism to detect misbehaving nodes in a network. In this paper, we propose a trust establishment method for cooperative wireless networks by using Bayesian framework. In contrast with the previous schemes proposed in wireless networks, this approach takes the channel state information and the relay selection decisions into account to derive a pure trust value for each relay node. The proposed method can be applied to any cooperative system with a general relay selection policy whose decisions in each cooperative transmission are independent of the previous ones. Moreover, it does not impose additional communication overhead on the system as it uses the available information in relay selection procedure. Copyright © 2012 John Wiley & Sons, Ltd.     

多约束容错性WSN中继节点布局算法的研究

针对目前中继节点布局算法所忽视的中继节点通信容量以及网络整体能耗等问题,本文将通信路径不可逆以及中继节点通信容量等约束条件引入现有中继节点布局模型,并提出了基于最小通信网络距离因子的布局算法评价新标准.解决方法上,采用了基于枚举法与贪婪寻优算法的中继节点布局算法,实现了WSN中继节点的多约束容错性布局.仿真实验表明,本...     

移动边缘计算中服务功能链的自适应优化部署策略

为解决移动边缘计算中面向用户的服务功能链（Service Function Chain,SFC）部署成本开销过大、时延过长问题,提出了针对SFC的支出成本与时延联合自适应优化的部署策略。首先,在虚拟网络功能（Virtualized Network Function,VNF）节点选取阶段,考虑路径损耗这一无线信道衰落问题,根据有线用户与无线用户的位置情况,选择当前最佳节点以降低SFC的响应时延。其次,在服务节点配置阶段,根据用户请求处理的数据内容的新鲜度记录,自适应动态增加和删减相应的缓存,利用资源感知算法在保证数据传递可靠性的同时,减少服务节点的配置个数,降低配置开销。最后,在SFC部署阶段,利用基于KSP（K-shortest Paths）的功耗感知算法确定最佳节点映射排序与通信链路,在减少通信链路重映射的同时还能保证部署的SFC的低成本与低时延。实验仿真结果表明,相比于已有方案,该方法能够有效降低部署成本与时延,并能对不同用户的SFC部署做到自适应优化,提高了SFC的部署成功率。     

Joint relay selection and power allocation algorithm in two-way relay networks with proportional fair constraint

In this paper,we consider the joint relay selection and power allocation problem for two-way relay systems with multiple relay nodes.Traditionally,relay selection schemes are primarily focused on selecting one relay node to maximize the transmission sum rate or minimize the outage probability.If so,it is possible to cause certain relay nodes overloaded.In addition,the joint relay selection and power allocation problem is a mixed integer program problem and prohibitive in terms of complexity.Therefore,we pro...     

无线协作网络中基于数据传输需求的分布式功率控制

在未来无线通信网络中,协作通信的性能依赖于通信资源的有效分配,比如中继选择和功率控制等.在本文中,我们建议了一个分布式买者和卖者博弈理论框架,以满足用户链路质量需求为基础,解决多用户协作通信中最优化中继选择和功率控制.本文联合考虑了源节点和中继节点的功率分配,进而优化源节点和中继节点的收益.这里提出的方法不仅有助于源节点找到相对位置较好的中继节点以及在源和中继之间进行最优化功率分配从而最小化源节点的支付,而且有助于相互竞争的中继节点提供优化的价格以最大化它们各自的收益.此外,这里的优化价格可以仅由局部信道状态信息和其他节点的能量价格决定.如果获得的中继节点总数增加,全网的能量消耗会更低.     

Energy‐Aware Hybrid Cooperative Relaying with Asymmetric Traffic

In this paper, we study an asymmetric two‐way relaying network where two source nodes intend to exchange information with the help of multiple relay nodes. A hybrid time‐division broadcast relaying scheme with joint relay selection (RS) and power allocation (PA) is proposed to realize energy‐efficient transmission. Our scheme is based on the asymmetric level of the two source nodes’ target signal‐to‐noise ratio indexes to minimize the total power consumed by the relay nodes. An optimization model with joint RS and PA is studied here to guarantee hybrid relaying transmissions. Next, with the aid of our proposed intelligent optimization algorithm, which combines a genetic algorithm and a simulated annealing algorithm, the formulated optimization model can be effectively solved. Theoretical analyses and numerical results verify that our proposed hybrid relaying scheme can substantially reduce the total power consumption of relays under a traffic asymmetric scenario; meanwhile, the proposed intelligent optimization algorithm can eventually converge to a better solution.