A CMOS passive mixer with low flicker noise for low-power direct-conversion receiver

A CMOS passive mixer is designed to mitigate the critical flicker noise problem that is frequently encountered in constituting direct-conversion receivers. With a unique single-balanced passive mixer design, the resulted direct-conversion receiver achieves an ultralow flicker-noise corner of 45 kHz, with 6 dB more gain and much lower power and area consumption than the double-balanced counterpart. CMOS switches with a unique bias-shifting network to track the LO DC offset are devised to reduce the second-order intermodulation. Consequently, the mixer's IIP2 has been greatly enhanced by almost 21 dB from a traditional single-balanced passive mixer. An insertion compensation method is also implemented for effective dc offset cancellation. Fabricated in 0.18 /spl mu/m CMOS and measured at 5 GHz, this passive mixer obtains 3 dB conversion gain, 39 dBm IIP2, and 5 dBm IIP3 with LO driving at 0 dBm. When the proposed mixer is integrated in a direct-conversion receiver, the receiver achieves 29 dB overall gain and 5.3 dB noise figure.     

A 1.5-V multi-mode quad-band RF receiver for GSM/EDGE/CDMA2K in 90-nm digital CMOS process

A single chip quad-band multi-mode (GSM900/ DCS1800/PCS1900/CDMA2K) direct-conversion RF receiver with integrated baseband ADCs is presented. The fully integrated RF receiver is implemented in a 90-nm single poly, six level metal, standard digital CMOS process with no additional analog and RF components. The highly digital multi-mode receiver uses minimum analog filtering and AGC stages, digitizing useful signal, dynamic DC offsets and blockers at the mixer output. The direct-conversion GSM front-end utilizes resistive loaded LNAs with only two coupled inductors per LNA. The GSM front-end achieves a 31.5 dB gain and a 2.1 dB integrated noise figure with a 5 dB noise figure under blocking conditions. The CDMA2K front-end utilizes a self-biased common-gate input amplifier followed by passive mixers, achieving wideband input matching from 900 MHz up to 2.1 GHz with an IIP3 of +8 dBm. The GSM receiver consumes 38 mA from a power supply of 1.5 V and CDMA2K receiver consumes 16 mA in the low band and 21 mA in the high band. The multi-mode receiver, including LO buffers and frequency dividers, ADCs, and reference buffers, occupies 2.5 mm/sup 2/.     

用于IEEE802．11b／g WLAN直接下变频接收机的射频前端设计

介绍了一种应用于IEEE802．11b／g无线局域网接收机射频前端的设计。基于直接下变频的系统架构。接收机集成了低噪声放大器、I／Q下变频器、去直流偏移滤波器、基带放大器和信道选择滤波器。电路采用TSMC0．18μm CMOS工艺设计,工作在2．4GHz ISM（工业、科学和医疗）频段,实现的低噪声放大器噪声系数为0．84dB,增益为16dB,S11低于-15dB,功耗为13mW;I／Q下变频器电压增益为2dB,输入1dB压缩点为-1 dBm,噪声系数为13dB,功耗低于10mw。整个接收机射频前端仿真得到的噪声系数为3．5dB,IIP3为-8dBm,IP2大于30dBm,电压增益为31dB,功耗为32mW。     

一个双频带可重构的直接变频接收机射频前端

A dual-band reconfigurable wireless receiver RF front-end is presented, which is based on the directconversion principle and consists of a low noise amplifer （LNA） and a down-converter. By utilizing a compact switchable on-chip symmetrical inductor, the RF front-end could be switched between two operation frequency bands without extra die area cost. This RF front-end has been implemented in the 180 nm CMOS process and the measured results show that the front-end could provide a gain of 25 dB and IIP3 of 6 dBm at 2.2 GHz, and a gain of 18.8 dB and IIP3 of 7.3 dBm at 4.5 GHz. The whole front-end consumes 12 mA current at 1.2 V voltage supply for the LNA and 2.1 mA current at 1.8 V for the mixer, with a die area of 1.2 × 1 mm^2.     

应用于802.11b无线局域网的低噪声高线性度的CMOS射频接收机

实现了一个单片集成、直接转换结构的2.4GHz CMOS接收机.这个正交接收机作为低成本方案应用于802.11b无线局域网系统,所处理的数据传输率为该系统的最大速率--11Mbps.基于系统设计以及低噪声高线性度考虑,设计了低噪声放大器、直接转换混频器、增益可变放大器、低通滤波器、直流失调抵消电路及其他辅助电路.该芯片采用中芯国际0.18μm 1p6m RF CMOS工艺流片.所测的接收机性能如下:噪声系数为4.1dB,高增益设置下低噪声放大器与混频器的输入三阶交调点为-7.5dBm,整个接收机的输入三阶交调点为-14dBm,相邻信道干扰抑制能力在距中心频率30MHz处达到53dBc,输出直流失调电压小于5mV.该接收机采用1.8V电源电压,I,Q两路消耗的总电流为44mA.     

A high IIP2 downconversion mixer using dynamic matching

This paper presents an RF downconversion mixer with improved rejection to second-order intermodulation for RF application within a direct-conversion receiver requiring high input blocking performance. The mixer, implemented in a 2.7-V 0.35-μm BiCMOS process, achieves a second-order input intercept point of at least +72 dBm for a BiCMOS design and at least +66 dBm for an all-CMOS design. The design utilizes dynamic matching to enhance the balance of a fully differential mixer through mitigation of both component and device mismatches. In addition, dynamic matching is shown to improve the mixer's 1/f noise performance. For an all-CMOS mixer design, a 30-dB improvement in the mixer's noise floor at 1 kHz has been observed compared to conventional fully differential CMOS Gilbert-cell mixer. Additionally, background is given on second-order intermodulation and on system IIP2 requirements for a direct-conversion receiver     

Current-mode design techniques in low-voltage 24-GHz RF CMOS receiver front-end

A new high frequency CMOS current-mode receiver front-end composed of a current-mode low noise amplifier (LNA) and a current-mode down-conversion mixer has been proposed in the frequency band of 24 GHz and fabricated in 0.13-μm 1P8M CMOS technology. The measurement of the current-mode receiver front-end exhibits a conversion gain of 11.3 dB, a noise figure (NF) of 14.2 dB, the input-referred 1-dB compression point (P_-1 dB)(P_{{-1}\,{\rm dB}}) of −13.5 dBm and the input-referred third-order intercept point (P _IIP3) of −1 dBm. The receiver dissipates 27.8 mW where the supply of LNA is 0.8 V and the supply of mixer is 1.2 V. The power consumption of output buffer is not included. The receiver front-end occupies the active area of 1.45 ×0.721.45 \times 0.72 mm² including testing pads. The measured results show that the proposed current-mode approach can be applied to a high-frequency receiver front-end and is capable of low-voltage applications in the advanced CMOS technologies.     

A direct conversion receiver with an IP2 calibrator for CDMA/PCS/GPS/AMPS applications

A second-order intercept point (IP2) calibration technique is developed using common-mode feedback (CMFB) circuitry in a direct-conversion receiver for wireless CDMA/PCS/GPS/AMPS applications. The IP2 calibrator is capable of providing different CMFB gain to tune its common-mode output impedance for each of the positive and negative mixer outputs. The CDMA mixer applying this method achieved a second-order input intercept point (IIP2) of 64 dBm, a third-order input intercept point (IIP3) of 4 dBm, a noise figure of 6.5 dB and a voltage gain of 42.2 dB. This result shows a 20 dB improvement from an uncalibrated IIP2 of 44 dBm. The receiver RFIC is implemented in a 0.5-/spl mu/m SiGe BiCMOS process, and it operates from a 2.7 to 3.1 V single power supply.     

A low noise CMOS RF front-end for UWB 6-9 GHz applications

An integrated fully differential ultra-wideband CMOS RF front-end for 6-9 GHz is presented.A resistive feedback low noise amplifier and a gain controllable IQ merged folded quadrature mixer are integrated as the RF front-end. The ESD protected chip is fabricated in a TSMC 0.13μm RF CMOS process and achieves a maximum voltage gain of 23-26 dB and a minimum voltage gain of 16-19 dB,an averaged total noise figure of 3.3-4.6 dB while operating in the high gain mode and an in-band IIP3 of-12.6 dBm while in th...     

A low power 3-5 GHz CMOS UWB receiver front-end

A novel low power RF receiver front-end for 3-5 GHz UWB is presented. Designed in the 0.13μm CMOS process, the direct conversion receiver features a wideband balun-coupled noise cancelling transconductance input stage, followed by quadrature passive mixers and transimpedance loading amplifiers. Measurement results show that the receiver achieves an input return loss below-8.5 dB across the 3.1-4.7 GHz frequency range, max-imum voltage conversion gain of 27 dB, minimum noise figure of 4 dB, IIP3 of-11.5 dBm, and IIP2 of 33 dBm. Working under 1.2 V supply voltage, the receiver consumes total current of 18 mA including 10 mA by on-chip quadrature LO signal generation and buffer circuits. The chip area with pads is 1.1 × 1.5 mm2.     

RF front-end of direct conversion receiver RFIC for cdma-2000

We report on the front-end of a highly integrated dual-band direct-conversion receiver IC for cdma-2000 mobile handset applications. The RF front-end included a CELL-band low-noise amplifier (LNA), dual-band direct-conversion quadrature I/Q down-converters, and a local-oscillator (LO) signal generation circuit. At 2.7 V, the LNA had a noise figure of 1.2 dB and input third-order intermodulation product (IIP3) of 9 dBm. I/Q down-converters had a noise figure of 4-5 dB and IIP3 of 4-5 dBm and IIP2 of 55 dBm. An on-chip phase-locked loop and external voltage-controlled oscillator generated the LO signal. The receiver RFIC was implemented in a 0.35-/spl mu/m SiGe BiCMOS process and meets or exceeds all cdma-2000 requirements when tested individually or on a handset.     

A low voltage current mode CMOS integrated receiver front-end for GPS system

This paper presents a low voltage, 1.6 GHz integrated receiver front-end which is implemented by the standard 0.35 μm, 3M2P CMOS technology. The receiver consists of a transconductance low noise amplifier (G_m-LNA), a down conversion current mode mixer and a voltage-controlled oscillator using accumulation-mode MOS varactor (A-MOS VCO). A current mode mixer is used to reduce the supply voltage to 1 V. A specially designed G_m-LNA converts RF input voltage to RF input current for the current mode mixer. This could eliminate an unnecessary I–V, V–I conversion and reduce the non-linearity contribution. Moreover, a low voltage A-MOS VCO, with a good phase noise and wide tuning frequency range, is used to generate a required oscillating frequency for the receiver. The integrated receiver front-end has a measured power conversion gain of 11.4 dB, an input referred third-order intercept point (IIP₃) of 6.1 dBm, and a noise figure of 5.87 dB. The measured total power consumption is 40.9 mW with 1 V supply.     

A low voltage CMOS RF front-end for IEEE 802.11b WLAN transceiver

A low voltage CMOS RF front-end for IEEE 802.11b WLAN transceiver is presented. The problems to implement the low voltage design and the on-chip input/output impedance matching are considered, and some improved circuits are presented to overcome the problems. Especially, a single-end input, differential output double balanced mixer with an on-chip bias loop is analyzed in detail to show its advantages over other mixers. The transceiver RF front-end has been implemented in 0.18 um CMOS process, the measured results show that the Rx front-end achieves 5.23 dB noise figure, 12.7 dB power gain (50 ohm load), −18 dBm input 1 dB compression point (ICP) and −7 dBm IIP3, and the Tx front-end could output +2.1 dBm power into 50 ohm load with 23.8 dB power gain. The transceiver RF front-end draws 13.6 mA current from a supply voltage of 1.8 V in receive mode and 27.6 mA current in transmit mode. The transceiver RF front-end could satisfy the performance requirements of IEEE802.11b WLAN standard. Supported by the National Natural Science Foundation of China, No. 90407006 and No. 60475018.     

Monolithic InGaP-GaAs HBT receiver front-end with 6 mW DC power consumption for 5 GHz band WLAN applications

A very low power consumption (6 mW) 5 GHz band receiver front-end using InGaP-GaAs HBT technology is reported. The receiver front-end is composed of a cascode low noise amplifier followed by a double-balanced mixer with the RF transconductor stage placed above the Gilbert quad for direct-coupled connection. The RF band of this receiver front-end is set to be 5.2 GHz, being downconverted to 1 GHz IF frequency. Input-return-loss (S/sub 11/) in RF port smaller than -12 dB and excellent power-conversion-gain of 35.4 dB are achieved. Input 1 dB compression point (P/sub 1dB/) and input third-order intercept point (IIP3) of -24 and -3 dBm, respectively, are also achieved.     

Design of a High Performance 2-GHz Direct-Conversion Front-End With a Single-Ended RF Input in 0.13 $mu$m CMOS

A 2.1 GHz CMOS front-end with a single-ended low-noise amplifier (LNA) and a double balanced, current-driven passive mixer is presented. The LNA drives an on-chip transformer load that performs single-ended to differential conversion. A detailed comparison in gain, noise, and second and third order linearity performance is presented to motivate the choice of a current-driven passive mixer over an active mixer. The front-end prototype was implemented on a 0.13 $mu$m CMOS process and occupies an active chip area of 1.1 mm $^{2}$. It achieves 30 dB conversion gain, a low noise figure of 3.1 dB (integrated from 40 KHz to 1.92 MHz), an in-band IIP3 of ${-}$12 dBm, and IIP2 better than 39 dBm, while consuming only 12 mW from a 1.5 V power supply.      

A 76-dBm IIP2 down-conversion mixer for TD-SCDMA/RFID applications

This paper presents a semi-active in-phase/quadrature inductor-less down-conversion mixer. The mixer consists of an active trans-conductance stage, a passive current switching stage, and a trans-impedance stage. A complementary input architecture has been used to increase the trans-conductance for a given bias current. An on-chip prescaler is added to provide the balanced LO signals, while the CMFB circuit in trans-conductance stage is designed to enhance linearity. The chip was achieved in a 0.13???m CMOS technology. It features 5?dB conversion gain over a broad range from 800?MHz to 2.1?GHz, which supports Chinese TD-SCDMA/RFID standards simultaneously. The maximum IIP2 is +76?dBm at 2.1?GHz and suitable for application within a direct-conversion receiver.     

A 1.1 V 6.2 mW,wideband RF front-end for 0 dBm blocker tolerant receivers in 90 nm CMOS

This paper presents the design and implementation of a low power, highly linear, wideband RF front-end in 90 nm CMOS. The architecture consists of an inverter-like common gate low noise amplifier followed by a passive ring mixer. The proposed architecture achieves a high linearity in a wide band (0.5–6 GHz) at very low power. Therefore, it is a suitable choice for software defined radio (SDR) receivers. The chip measurement results indicate that the inverter-like common gate input stage has a broadband input match achieving S11 below −8.8 dB up to 6 GHz. The measured single sideband noise figure at an LO frequency of 3 GHz and an IF of 10 MHz is 6.25 dB. The front-end achieves a voltage conversion gain of 4.5 dB at 1 GHz with 3 dB bandwidth of more than 6 GHz. The measured input referred 1 dB compression point is +1.5 dBm while the IIP3 is +11.73 dBm and the IIP2 is +26.23 dBm respectively at an LO frequency of 2 GHz. The RF front-end consumes 6.2 mW from a 1.1 V supply with an active chip area of 0.0856 mm².     

A 1.2-V RF front-end with on-chip VCO for PCS 1900 direct conversion receiver in 0.13-/spl mu/m CMOS

In this paper, a 1.2-V RF front-end realized for the personal communications services (PCS) direct conversion receiver is presented. The RF front-end comprises a low-noise amplifier (LNA), quadrature mixers, and active RC low-pass filters with gain control. Quadrature local oscillator (LO) signals are generated on chip by a double-frequency voltage-controlled oscillator (VCO) and frequency divider. A current-mode interface between the downconversion mixer output and analog baseband input together with a dynamic matching technique simultaneously improves the mixer linearity, allows the reduction of flicker noise due to the mixer switches, and minimizes the noise contribution of the analog baseband. The dynamic matching technique is employed to suppress the flicker noise of the common-mode feedback (CMFB) circuit utilized at the mixer output, which otherwise would dominate the low-frequency noise of the mixer. Various low-voltage circuit techniques are employed to enhance both the mixer second- and third-order linearity, and to lower the flicker noise. The RF front-end is fabricated in a 0.13-/spl mu/m CMOS process utilizing only standard process options. The RF front-end achieves a voltage gain of 50 dB, noise figure of 3.9 dB when integrated from 100 Hz to 135 kHz, IIP3 of -9 dBm, and at least IIP2 of +30dBm without calibration. The 4-GHz VCO meets the PCS 1900 phase noise specifications and has a phase noise of -132dBc/Hz at 3-MHz offset.     

A dual-band RF front-end for WCDMA and GSM applications

An RF front-end for dual-band dual-mode operation is presented. The front-end consumes 22.5 mW from a 1.8-V supply and is designed to be used in a direct-conversion WCDMA and GSM receiver. The front-end has been fabricated in a 0.35-μm BiCMOS process and, in both modes, can use the same devices in the signal path except the LNA input transistors. The front-end has a 27-dB gain control range, which is divided between the LNA and quadrature mixers. The measured double-sideband noise figure and voltage gain are 2.3 dB, 39.5 dB, for the GSM and 4.3 dB, 33 dB for the WCDMA, respectively. The linearity parameters IIP3 and IIP2 are -19 dBm, +35 dBm for the GSM and -14.5 dBm and +34 dBm for the WCDMA, respectively     

A 40 GHz single-ended down-conversion mixer in 0.13 /spl mu/m SiGeC BiCMOS HBT

This work presents a single-ended active mixer realized with a 0.13 /spl mu/m BiCMOS SiGeC heterojunction bipolar transistor (HBT) technology. This mixer is designed to be integrated in a superheterodyne receiver for 40 GHz wireless communication systems. Local oscillator (LO) and RF signals are directly applied to the base of the HBT through two coupled lines. The mixer provides a down-conversion from 42 GHz to 2 GHz. The mixer exhibits a power conversion gain better than 2.4 dB and a measured double-sideband noise figure less than 8.3 dB for P/sub LO/=3 dBm (power of the local oscillator) under a global power consumption lower than 9.5 mW. This architecture exhibits good linearity performance with a measured IP/sub 1dB/ of about -7 dBm and an IIP3 of +4 dBm. The linear dynamic range for a 2 GHz system bandwidth is approximately 65 dB for P/sub LO/=+2 dBm and T/sub 0/=290 K. The third order spurious free dynamic range is calculated to be better than 52 dB.