Load Configuration and Lateral Distribution of NATO Wheeled Military Trucks for Steel I-Girder Bridges

This paper presents the lateral load distribution of various North Atlantic Treaty Organization (NATO) wheeled military trucks on a simple-span steel I-girder bridge (L = 36?m). The military trucks are classified into the military load classification (MLC) system. The MLC trucks demonstrate different load configurations when compared to the standard HS20 truck in terms of wheel-line spacing, number of axles, and weight. A calibrated three-dimensional finite-element analysis is conducted to examine the MLC load effects. The applicability of the AASHTO LRFD provisions is evaluated using 72 different load models. The wheel-line spacing and weight of the MLC trucks cause different flexural behavior and load distributions of the bridge when compared to those of HS20. The current AASHTO LRFD approach to determine live load distribution factors may be reasonably applicable to the MLC trucks, including approximately 20% of conservative predictions.     

Development of Live-Load Distribution Factors for Glued-Laminated Timber Girder Bridges

This paper presents simple relationships for calculating live-load distribution factors for glued-laminated timber girder bridges with glued-laminated timber deck panels. Analytical models were developed using the Ansys 113 finite-element program, and the results were validated using recorded data from four in-service timber bridges. The effects of the bridge span length, the spacing between girders, and the bridge width on the distribution of the live load were investigated by using the validated models. The live-load distribution factors obtained from the field test and the analytical models were compared with those obtained using the AASHTO LRFD Bridge Design Specifications2 live-load distribution relations. The comparison showed that the live-load distribution factors obtained by using the AASHTO LRFD Bridge Design Specifications2 were conservative. For this reason, statistical methods were used to develop accurate relationships that can be used to calculate the live-load distribution factors in the design of glued-laminated girder bridges.     

Experimental Verification of Horizontally Curved I-Girder Bridge Behavior

Past research has been conducted on the behavior of horizontally curved girders by testing scaled models and full-scale laboratory bridges and by analyzing numerical models. Current design specifications are based on this past research; however, little field data of in-service bridges exist to support the findings of the past research on which the current design criteria are based. The purpose of the present study was to gather field response data from three in-service, curved, steel I-girder bridges to determine behavior when subjected to a test truck and normal truck traffic. Transverse bending distribution factors and dynamic load allowance were calculated from the data collected. Numerical grillage models of the three bridges were developed to determine if a simple numerical model will accurately predict actual field measured transverse bending distribution, deflections, and cross-frame and diaphragm shear forces. The present study found that AASHTO specifications are conservative for both dynamic load allowance and transverse bending moment distribution. The grillage models were found to predict with reasonable accuracy the behavior of a curved I-girder bridge.     

Probabilistic Characterization of Live Load Using Visual Counts and In-Service Strain Monitoring

It has been argued that the AASHTO LRFD design code for maximum live loads on highway bridges is overly conservative. In an attempt to determine the level of conservativeness, if any, the writers developed a methodology incorporating real-time visual data collection from traffic cameras coupled with structural strain response of girder bridges. Average daily truck traffic along with frequency of multiple presences (same lane as well as adjacent lanes) and lane-wise truck traffic distribution were estimated for a steel-girder highway bridge on I-95 in Delaware. These data compared well with predictions from a Poisson process based model developed for this study. Statistical properties of girder moments in single and multiple presence conditions were determined as well. In this particular example, the girder design moment on the 24.6?foot approach span according to AASHTO specifications was found to be about 3.5 times higher than that estimated from the in-service data.     

Full-Scale Test and Analysis of a Curved Steel-Box Girder Bridge

Since the first edition of the AASHTO Guide Specifications for Horizontally Curved Steel Girder Highway Bridges was published in 1980, there have been two more editions including many revisions to the specifications. Some changes were based on valid research results and others were based on limited or uncertain research results and information. The current edition of the specifications contains provisions that may result in unreasonably conservative load capacity ratings. In this paper, the results of field tests and analyses conducted on the Veterans’ Memorial curved steel-box girder bridge are discussed. Test and analytical results show: (1) current AASHTO guide specifications regarding the first transverse stiffener spacing at the simple end support of a curved girder may be too conservative for bridge load capacity ratings; (2) current AASHTO guide specifications may greatly overestimate the dynamic loadings of curved box girder bridges with long span lengths; and (3) a plane grid finite-element model of about 20 elements per span in the longitudinal direction can be used to analyze curved multigirder bridges with external bracings located only over supports. The research results are instructive and applicable to bridge design and bridge load-rating activities.     

Field Testing and Analysis of CRC Deck Girder Bridges

This paper presents findings of field tests and analysis of two conventionally reinforced concrete (CRC) deck girder bridges designed in the 1950s. The bridges are in-service and exhibit diagonal cracks. Stirrup strains in the bridge girders at high shear regions were used to estimate distribution factors for shear. Impact factors based on the field tests are reported. Comparison of field measured responses with AASHTO factors was performed. Three-dimensional elastic finite-element analysis was employed to model the tested bridges and determine distribution factors specifically for shear. Eight-node shell elements were used to model the decks, diaphragms, bent caps, and girders. Beam elements were used to model columns under the bent caps. The analytically predicted distribution factors were compared with the field test data. Finally, the bridge finite-element models were employed to compare load distribution factors for shear computed using procedures in the AASHTO LRFD and Standard Specifications.     

Live-Load Distribution Factors for Prestressed Concrete, Spread Box-Girder Bridge

This study presents an evaluation of shear and moment live-load distribution factors for a new, prestressed concrete, spread box-girder bridge. The shear and moment distribution factors were measured under a live-load test using embedded fiber-optic sensors and used to verify a finite element model. The model was then loaded with the American Association of State Highway and Transportation (AASHTO) design truck. The resulting maximum girder distribution factors were compared to those calculated from both the AASHTO standard specifications and the AASHTO LRFD bridge design specifications. The LRFD specifications predictions of girder distribution factors were accurate to conservative when compared to the finite element model for all distribution factors. The standard specifications predictions of girder distribution factors ranged from highly unconservative to highly conservative when compared to the finite element model. For the study bridge, the LRFD specifications would result in a safe design, though exterior girders would be overdesigned. The standard Specifications, however, would result in an unsafe design for interior girders and overdesigned exterior girders.     

Design Recommendations for a FRP Bridge Deck Supported on Steel Superstructure

No appropriate provisions from either AASHTO Standard (2002) or AASHTO LRFD (2004) bridge design specifications are available for the design of fiber-reinforced polymer (FRP)-deck-on-steel-superstructure bridges. In this research, a parametric study using the finite-element method (FEM) is conducted to examine two design issues concerning the design of FRP-deck-on-steel-superstructure bridges, namely deck relative deflection and load distribution factor (LDF). Results show that the strip method specified in AASHTO LRFD specification as an approximate method of analysis, can also be applied to FRP decks as a practical method. However, different strip width equations have to be determined by either FEM or experimental methods for different types of FRP decks. In this study, one such equation has been derived for the Strongwell deck. In addition, both FEM results and experimental measurements show that the AASHTO LDF equations for glued laminated timber decks on steel stringers provide good estimations of LDF for FRP-deck-on-steel-superstructure bridges. Finally, it is found that the lever rule can be used as an appropriately conservative design method to predict the LDF of FRP-deck-on-steel-superstructure bridges.     

Determination of Bridge Design Parameters through Field Evaluation of the Route 601 Bridge Utilizing Fiber-Reinforced Polymer Girders

The Route 601 Bridge in Sugar Grove, Virginia, spans 11.89?m (39?ft) over Dickey Creek. The bridge is the first to use the Strongwell 91.4?cm (36?in.) deep fiber-reinforced polymer double web beam in a vehicular bridge superstructure. Construction of the new bridge was completed in October 2001 and field testing was undertaken shortly thereafter, as well as in June of 2002, to assess any potential changes in structural performance. This paper details the field evaluation of the Route 601 Bridge. Using midspan deflection and strain data from the October 2001 and June 2002 field tests, AASHTO bridge design parameters were determined—namely, wheel load distribution factor g, dynamic load allowance IM, and maximum deflection. The wheel load distribution factor was determined to be S/4, a dynamic load allowance was determined to be 0.36, and the maximum deflection of the bridge was L/1,110. Deflection results were lower than the AASHTO L/800 limit. This discrepancy is attributed to partial composite action of the deck-to-girder connections, bearing restraint at the supports, and contribution of guardrail stiffness. It was found that diaphragm removal had a small effect on the wheel load distribution factor.     

Demonstration of Use of High-Performance Lightweight Concrete in Bridge Superstructure in Virginia

The general objective of this research was the construction and evaluation of a bridge using high-performance lightweight concrete (HPLWC). The resulting bridge over the Chickahominy River near Richmond, Va., consists of 15 prestressed American Association of State Highway and Transportation Officials (AASHTO) Type IV girders made of HPLWC with a density of 1,920?kg/m3 and a minimum required 28-day compressive strength of 55?MPa. The bridge also has a lightweight concrete (LWC) deck with a density of 1,850?kg/m3 and a minimum required 28-day compressive strength of 30?MPa. This research study is chiefly concerned with investigating the effects of using lightweight concrete in prestressed girders on transfer length, development length, flexural strength, girder live-load distribution factor, and dynamic load allowance. Transfer length was determined to be 432?mm, or 33?db, for several girders at the time of prestress transfer. The development length was determined to be between 1,830 and 2,440?mm, while the flexural strength ranged from 11 to 30% higher than the AASHTO flexural capacity. The measured distribution factors and dynamic load allowance were smaller than the AASHTO standard and LRFD values.     

LRFD Orthotropic Plate Model for Live Load Moment in Filled Grid Decks

Due to the orthogonal elastic properties and significant two-way bending action, orthotropic plate theory may best be used to describe the behavior of concrete filled grid bridge decks. The current AASHTO LRFD specification employs an orthotropic plate model with a single patch load to predict live load moment in concrete filled grid bridge decks, which may not be conservative. This paper presents alternative equations to predict maximum moments, based on classical orthotropic plate theory, which include multiple patch loads, both the LRFD design truck and tandem load cases, and the two most common deck orientations. The predicted moments are verified through finite-element analyses.     

Equivalent Wheel Load Approach for Slender Cable-Stayed Bridge Fatigue Assessment under Traffic and Wind: Feasibility Study

In the current AASHTO LRFD specifications, the fatigue design considers only one design truck per bridge with 15% dynamic allowance. While this empirical approach may be practical for regular short and medium span bridges, it may not be rational for long-span bridges (e.g., span length >152.4?m or 500?ft) that may carry many heavy trucks simultaneously. Some existent studies suggested that fatigue may not control the design for many small and medium bridges. However, little research on the fatigue performance of long-span bridges subjected to both wind and traffic has been reported and if fatigue could become a dominant issue for such a long-span bridge design is still not clear. Regardless if the current fatigue design specifications are sufficient or not, a real understanding of the traffic effects on bridge performance including fatigue is desirable since the one truck per bridge for fatigue design does not represent the actual traffic condition. As the first step toward the study of fatigue performance of long-span cable-stayed bridges under both busy traffic and wind, the equivalent dynamic wheel load approach is proposed in the current study to simplify the analysis procedure. Based on full interaction analyses of a single-vehicle–bridge–wind system, the dynamic wheel load of the vehicle acting on the bridge can be obtained for a given vehicle type, wind, and driving condition. As a result, the dimension of the coupled equations is independent of the number of vehicles, through which the analyses can be significantly simplified. Such simplification is the key step toward the future fatigue analysis of long-span bridges under a combined action of wind and actual traffic conditions.     

FEA of Complex Bridge System with FRP Composite Deck

Innovative fiber-reinforced polymer (FRP) composite highway bridge deck systems are gradually gaining acceptance in replacing damaged/deteriorated concrete and timber decks. FRP bridge decks can be designed to meet the American Association of State Highway and Transportation Officials (AASHTO) HS-25 load requirements. Because a rather complex sub- and superstructure system is used to support the FRP deck, it is important to include the entire system in analyzing the deck behavior and performance. In this paper, we will present a finite-element analysis (FEA) that is able to consider the structural complexity of the entire bridge system and the material complexity of an FRP sandwich deck. The FEA is constructed using a two-step analysis approach. The first step is to analyze the global behavior of the entire bridge under the AASHTO HS-25 loading. The next step is to analyze the local behavior of the FRP deck with appropriate load and boundary conditions determined from the first step. For the latter, a layered FEA module is proposed to compute the internal stresses and deformations of the FRP sandwich deck. This approach produces predictions that are in good agreement with experimental measurements.     

Evaluation of In-Service Performance of Tom’s Creek Bridge Fiber-Reinforced Polymer Superstructure

The Tom’s Creek Bridge is a small-scale demonstration project involving the use of fiber-reinforced polymer (FRP) composite girders as the main load-carrying members. The project is intended to serve two purposes. First, by calculating bridge design parameters such as the dynamic load allowance, transverse wheel load distribution, and deflections under service loading, the Tom’s Creek Bridge aids in modifying current American Association of State Highway and Transportation Officials bridge design standards for use with FRP composite materials. Second, by evaluating the FRP girders after exposure to service conditions, the project begins to answer questions about the long-term performance of these advanced composite material beams when used in bridge design. This paper details the in-service analysis of the Tom’s Creek Bridge. Five load tests, at 6-month intervals, were conducted on the bridge. Using midspan strain and deflection data gathered from the FRP composite girders during these tests, the aforementioned bridge design parameters have been determined. The Tom’s Creek Bridge was determined to have a maximum dynamic load allowance, IM, of 0.90, a transverse wheel load distribution factor, g, of 0.101, and a maximum deflection of L/490. Two bridge girders were removed from the Tom’s Creek Bridge after 15 months of service loading. These FRP composite girders were tested at the Structures and Materials Research Laboratory at Virginia Tech for stiffness and ultimate strength and compared to preservice values for the same beams. These measurements indicate that, after 15 months of service, the FRP composite girders have not significantly changed in stiffness or ultimate moment capacity.     

The beta-adrenomimetic effect of human and animal blood serum

The conventional analysis and design of highway bridges ignore the contribution of sidewalks and∕or railings in a bridge deck when calculating the flexural strength of superstructures. The presence of sidewalks and railings or parapets acting integrally with the bridge deck have the effect of stiffening the outside girders and attracting more load while reducing the load effects in the interior girders. This paper presents the results of a parametric study showing the influence of typical sidewalks and railings on wheel load distribution as well as on the load-carrying capacity of highway bridges. A typical one-span, two-lane, simply supported, composite steel girder bridge was selected in order to investigate the influence of various parameters such as: span length, girder spacing, sidewalks, and railings. A total of 120 bridges were analyzed using three-dimensional finite-element analysis. American Association of State Highway and Transportation Officials (AASHTO) HS20 design trucks were positioned in both lanes to produce the maximum moments. The finite-element analysis results were also compared with AASHTO wheel load distribution factors. The AASHTO load and resistance factor design (LRFD) wheel load distribution formula correlated conservatively with the finite-element results and all were less than the typical empirical formula (S∕5.5). The presence of sidewalks and railings were shown to increase the load-carrying capacity by as much as 30% if they were included in the strength evaluation of highway bridges.     

Shear Live-Load Distribution Factors for I-Girder Bridges

A full scale, single lane test bridge was used to evaluate a typical slab-on-girder bridge’s response to shear. The results of the shear load test provided the means to evaluate the level of detail for a finite element model that is required to accurately replicate the behavior of bridges subject to shear loads. This finite element modeling scheme was then used to evaluate more than 200 finite element bridge models. The bridge models investigated the effects of girder spacing, span length, overhang distance and skew angle on the shear live-load distribution factor. The finite element shear distribution factors were compared with those calculated according to the American Association of State Highway and Transportation Officials load and resistance factor design (AASHTO LRFD) specifications. It was found that the AASHTO LRFD procedure accurately predicted the shear distribution factor for changes in girder spacing and span length. However, the LRFD shear distribution factor for the exterior girder was found to be unconservative for certain overhang distances and overly conservative for the interior girder for higher skew angles. Alternative equations are provided for the single and multilane exterior girder correction factor.     

Simplified Method of Lateral Distribution of Live Load Moment

This paper introduces a simplified method, known as Henry’s method, for the calculation of distribution factors of the live load moment. Using the simplified method, the live load effects are equally distributed in all beams, including interior and exterior beams. This method has been used in Tennessee for nearly four decades. It offers advantages in simplicity of calculation and flexibility in application. To carefully examine the simplified method, 24 actual bridges of six different types of superstructures were selected for the study. The distribution factors of actual bridges using Henry’s method were compared with the ones from the AASHTO LRFD, the AASHTO standard, and finite-element analysis. In the comparison study, the effects of bridge superstructure types and key parameters that significantly affected the calculation of distribution factors are discussed. Based on the results of the comparison and evaluation, a modified Henry’s method was proposed by introducing modification factors to Henry’s method. With proper modification, the simplified method can be used to determine reasonable and reliable distribution factors of the live load moment.     

Flexural Lateral Load Distribution Characteristics of Sandwich Plate System Bridges: Parametric Investigation

The sandwich plate system (SPS) is a relatively new bridge deck system that consists of steel face plates bonded to a rigid polyurethane core. The decks are thin, lightweight, and modular in design and can be tailored to numerous applications. This system provides an excellent alternative for the rapid construction and rehabilitation of bridge decks. With any new system, there exists some uncertainty in the design procedures as a result of the limited population for comparison. This paper presents the results of a finite-element parametric investigation of the lateral load distribution characteristics of SPS bridges. The parametric study primarily focuses on the influence of deck thickness on distribution behavior as compared to conventional reinforced concrete decks. Results from the study demonstrate that the inherent flexibility of a thin SPS deck yields larger distribution factors (up to 20%) than a typical reinforced concrete deck, but these distribution factors can still be conservatively estimated with current AASHTO LRFD methods. Additional comparisons indicate that the distribution behavior of SPS bridges can also be estimated with the equations proposed by the NCHRP 12-62 project.     

Field Static Load Test on Kao-Ping-Hsi Cable-Stayed Bridge

Field load testing is an effective method for understanding the behavior and fundamental characteristics of a cable-stayed bridge. This paper presents the results of field static load tests on the Kao-Ping-Hsi cable-stayed bridge, the longest cable-stayed bridge in Taiwan, before it was open to traffic. A total of 40 loading cases, including the unit and distributed bending and torsion loading effects, were conducted to investigate the bridge behavior. The atmospheric temperature effect on the variations of the main girder deflections was also monitored. The results of static load testing include the main girder deflections, the flexural strains of the prestressed concrete girder, and the variations of the cable forces. A three-dimensional finite-element model was developed. The results show that the bridge under the planned load test conditions has linear superposition characteristics and the analytical model shows a very good agreement with the bridge responses. Further discussion of deflection and cable forces of the design specifications for a cable-stayed bridge is also presented.     

Effect of Bearing Pads on Precast Prestressed Concrete Bridges

Precast AASHTO concrete bridge I-beams are often supported at the ends by elastomeric bearing pads. The bearing pad-bridge beam interface defines support boundary conditions that may affect the performance of the bridge. In this study, finite-element modeling was used to validate AASHTO bearing stiffness specifications. Stiffness characteristics of the Florida DOT bearing pads were theoretically determined under varying elastomer shear modulus values. Finite-element models of AASHTO Types III and V beams were subjected to simulated static truckloads. Vertical and horizontal spring elements simulating new bearing pads were incorporated at the ends of the beam models. A full section of a bridge on U.S. Route 27 was also modeled, and the results were compared with field tests. In general, the restraint effects of the bearing pads are beneficial to the performance of the beams and the bridge. The beneficial effect, however, is small for new bearing pads and more pronounced under a drastic increase in bearing stiffness due to aging and colder temperatures. Such a dramatic increase in bearing stiffness must be justified if the beneficial elements are to be utilized. Current Florida DOT bearing pads are serving the main purpose of their application, which is to provide minimum horizontal restraint force to the beams while allowing horizontal movement.