Determination of methylmercury and butyltin compounds in marine biota and sediments using microwave-assisted acid extraction,solid-phase microextraction,and gas chromatography with microwave-induced plasma atomic emission spectrometric detection

A method is described for the determination of methylmercury and butyltin compounds in marine sediment and tissue using microwave-assisted acid extraction or digestion and solid-phase microextraction (SPME) followed by analysis using gas chromatography with microwave-induced plasma atomic emission spectrometric detection (GC-MIP-AES). Using the SPME-GC-MIP-AES method, enrichment factors for methylmercury and butyltin compounds of 50-100 were achieved, as compared to the typical hexane extraction, and measurements in marine tissue and sediment matrixes were possible at 1-2 microg/kg (methylmercury) and 10-100 ng/kg (butyltins). The SPME-GC-MIP-AES method was validated using several marine sediment and tissue matrix certified reference materials (CRMs) with certified values for methylmercury and butyltin compounds. The SPME-GC-MIP-AES method was used to measure methylmercury in four marine tissue CRMs ranging from oyster tissue at 13.0 +/- 1.0 microg/kg to fish tissue at 397 +/- 13 microg/kg (as Hg dry mass). Results from the SPME-GC-MIP-AES method were used in conjunction with results from other techniques to assign certified values for methylmercury in oyster, mussel, and fish tissue CRMs. Mono-, di-, and tributyltin were measured in three sediment CRMs at concentration levels of (0.08 +/- 0.03)-(0.35 +/- 0.05) mg/kg (as Sn dry mass).     

Separation,preconcentration and inductively coupled plasma-mass spectrometric (ICP-MS) determination of thorium(IV), titanium(IV), iron(III), lead(II) and chromium(III) on 2-nitroso-1-naphthol impregnated MCI GEL CHP20P resin

A simple and effective method is presented for the separation and preconcentration of Th(IV), Ti(IV), Fe(III), Pb(II) and Cr(III) by solid phase extraction on 2-nitroso-1-naphthol impregnated MCI GEL CHP20P resin prior to their inductively coupled plasma-mass spectrometric determinations. The influence of analytical parameters including pH of the aqueous solution, flow rates of sample and eluent solutions and sample volume on the quantitative recoveries of analyte ions was investigated. Matrix effects caused by the presence of alkali, earth alkali and some metal ions in the analyzed solutions were investigated. The presented solid phase extraction method was applied to BCR-144R Sewage Sludge (domestic origin), BCR-141R Calcareous Loam Soil, NIST 1568a Rice Flour and NIST 1577b Bovine Liver certified reference materials (CRMs) for the determination of analyte ions and the results were in good agreement with the certified values. The separation procedure presented was also applied to the various natural water samples collected from Turkey with satisfactory results.     

Direct determination of methylmercury and inorganic mercury in biological materials by solid sampling-electrothermal vaporization-inductively coupled plasma-isotope dilution-mass spectrometry

This paper reports on the use of solid sampling-electrothermal vaporization-inductively coupled plasma mass spectrometry (SS-EIV-ICPMS) for the direct and simultaneous determination of methylmercury and inorganic mercury in biological materials. The main advantage of this fast and sensitive method is that no sample preparation is required. In this way, the sample throughput can be considerably increased, problems of contamination and analyte losses are kept to a minimum and, even more important, the original chemical form of the different analyte species in the solid samples is preserved. To achieve this goal, a solid sample is inserted into a graphite furnace of the boat-in-tube type and is subsequently submitted to an appropriate temperature program, leading to the separate vaporization of methylmercury and inorganic mercury, which are transported into the ICP by means of an argon carrier gas. The separation was accomplished within 75 s. For the quantification of the two peaks, species-unspecific isotope dilution was used. For this purpose, a stable flow of argon loaded with gaseous Hg isotopically enriched in 200Hg was generated using a permeation tube that was constructed in-house. Its emission rate was determined by collecting the mercury released during a given time interval on a gold-coated silica absorber, after which the amount collected was released by heating of the absorber and determined by cold vapor atomic absorption spectrometry (CVAAS) and cold vapor atomic fluorescence spectrometry (CVAFS). A reference material from the Canadian National Research Council (NRC) (TORT-2) was used to assess the accuracy of the method. For the application of the method to samples with diverse mercury contents, the spike/sample ratio can be optimized by varying the emission rate of the permeation tube simply by adapting its temperature. To prove the feasibility of this approach, two reference materials (BCR 463 and DORM-2) with a methylmercury content more than 10 times higher than that of TORT-2 were also analyzed. The detection limits obtained for 1 mg of sample (2 ng g(-1) and 6 ng g(-1) for methylmercury and inorganic mercury, respectively) were found to be sufficiently low for this kind of application and are competitive when compared to other techniques.     

Application of isotopically labeled methylmercury for isotope dilution analysis of biological samples using gas chromatography/ICPMS

An isotope dilution (ID) procedure for the determination of methylmercury (MMHg) in biological samples using an inductively coupled plasma mass spectrometer as detector after the capillary gas chromatographic separation (CGC/ICPMS) has been developed. For the first time, open-focused-microwave pretreatment has been used in conjunction with ID. Optimum conditions for the measurement of isotope ratios on the fast transient chromatographic peaks have been established. Mass bias was found to be about 1.5%/mass unit and was corrected by using the simultaneously measured thallium signals at 203Tl and 205Tl. After mass-bias correction, deviation of the theoretical mercury ratio values was found to be as low as 0.2%. Isotope ratio precisions based on the peak areas measurements were 0.3% RSD for 20 pg injected (as Hg absolute). The absolute detection limits were in the range of 20-30 fg for 202Hg and 201Hg. Methylmercury enriched in 201Hg has been synthesized by direct reaction with methylcobalamine. The concentration of the MMHg spike has been measured by reverse isotope dilution with a natural MMHg standard. The capabilities of CGC/ICPMS to measure isotope ratios were used to optimize sample derivatization by aqueous ethylation with NaBEt4 with respect to MMHg degradation pathways and quantitative recovery. The accuracy of the method developed has been validated with biological certified reference materials (CRM-463, DORM-1).     

颗粒计数标准物质定值方法研究

为了探讨颗粒计数标准物质研究中缺乏操作性强、量值溯源可靠的颗粒计数标准物质定值方法等主要技术难点,本文中采用量值可溯源至长度基准的显微图象分析仪,配以血球计数板为球形乳胶颗粒计数标准物质定值,在确定标准值同时对于定值的不确定度进行了分析和研究。研究结果表明:采用这种方法的定值不确定度优于10%(k=2)。     

碳黑比表面积标准物质的研制

选择商品化的碳黑作为比表面积标准物质候选材料,利用交叉缩分的方法对碳黑样品进行分装。经均匀性、稳定性(18个月)检验,碳黑标准物质样品具有良好的均匀性和稳定性。按照国际公认的氮气物理吸附BET方法,联合测量能力经确认过的8家实验室对碳黑标准物质样品进行定值(104.6、29.9、8.96 m2/g)。与国内外同类标准物质比较表明:研制的3种碳黑比表面积标准物质的相对不确定度(2.1%、2.3%和3.2%)达到国际同类标准物质的先进水平。     

Development and evaluation of a reference measurement procedure for the determination of estradiol-17beta in human serum using isotope-dilution liquid chromatography-tandem mass spectrometry

Estradiol is the most potent natural estrogen and is derived from the ovaries. Its concentration in blood is measured to determine ovarian function. A reference measurement procedure for estradiol in serum involving isotope-dilution coupled with liquid chromatography-tandem mass spectrometry (LC/MS/MS) has been developed and critically evaluated. A deuterated estradiol (estradiol-d3) was used as an internal standard. The estradiol and its internal standard were extracted from serum matrix using solid-phase extractions and derivatized with dansyl chloride prior to reversed-phase LC/MS/MS. The accuracy of the measurement was evaluated by a comparison of results of this reference method on lyophilized human serum reference materials for estradiol [Certified Reference Materials (CRMs) 576, 577, and 578] with the certified values determined by gas chromatography/mass spectrometry (GC/MS) reference methods and by a recovery study for the added estradiol. The results of this method for estradiol agreed with the certified values within the uncertainty of the measurements for the three CRMs. The recovery of the added estradiol ranged from 100.7 to 101.8%. This method was applied to the determination of estradiol in frozen serum samples from three individual female donors. Excellent reproducibility was obtained with within-set coefficient of variations (CVs) ranging from 0.6 to 2.2% and between-set CVs ranging from 0.2 to 0.4%. Excellent linearity was also obtained, with correlation coefficients of all linear regression lines (measured intensity ratios vs mass ratios) ranging from 0.998 to 1.000. The detection limit at a signal-to-noise ratio of approximately 3 was 0.6 pg of estradiol (or 1 ng/L, as expressed as a concentration). This well-characterized LC/MS/MS method for serum estradiol, which demonstrates good accuracy and precision, low susceptibility to interferences, and comparability with GC/MS reference methods, qualifies as a reference measurement procedure that can be used to provide an accuracy base to which routine methods for estradiol can be compared and that will serve as a standard of higher order for measurement traceability.     

Development of Crude Oil Reference Material Certified for the Concentrations of Sulfur,Iron, Nickel,Vanadium and Magnesium

Crude oil quality and uses are largely affected by the presence of sulfur and some other elements. Controlling the risk associated with these elements in crude oil depends on their accurate determination which is crucially governed by the use of certified reference materials (CRMs). This paper describes the development of a natural-matrix reference material for quantification of sulfur, iron, nickel, vanadium and magnesium in crude oil. The crude oil was homogenized and bottled to prepare the candidate material. Homogeneity and stability of the prepared reference material were investigated and characterization of sulfur content was carried out using wavelength-dispersive X-ray fluorescence (WD-XRF) spectrometry and gravimetric methods. Meanwhile, characterization of iron, nickel, vanadium and magnesium content was carried out using atomic absorption spectrometry (AAS) and inductively coupled plasma-optical emission spectrometry (ICP-OES) techniques. Statistical evaluation of the data showed good homogeneity and stability of the candidate reference material. Sufficiently good agreement between methods of characterization was achieved which allowed certification. The certified values and their associated uncertainties were statistically derived using the approach of combining data from two or more independent analytical methods developed by National Institute for Standards and Technology (NIST, Gaithersburg, USA).     

Species-selective analysis by microcolumn multicapillary gas chromatography with inductively coupled plasma mass spectrometric detection.

A glass rod (5-20 cm long, 2 mm o.d.) containing more than 1200 parallel microchannels (< 40 microns i.d.) was converted into a high-resolution (> 100 theoretical plates cm-1) GC column by coating the inside of each channel in a way that compensated for the dispersion of the channel inner diameter. The columns were evaluated for the separation of mixtures of several organometallic (Hg, Sn, Pb) compounds prior to on-line sensitive metalselective detection by ICPMS. Chromatographic separation conditions were optimized to enable a rapid (within a maximum 30 s) multielemental speciation analysis. Absolute detection limits were 0.1 pg for Hg, 0.05 pg for Sn, and 0.03 pg for Pb using the carrier gas flows of approximately 200 mL min-1. The microcolumn multicapillary GC/ICPMS developed was applied to the analysis of a number of environmental samples. The results were validated with certified reference materials for tin (BCR477, PACS-2) and mercury (DORM-1, TORT-1).     

Speciation analysis for organotin compounds in biomaterials after integrated dissolution, extraction, and derivatization in a focused microwave field

Hydrolysis with acetic acid carried out in a low-power focused microwave field in the presence of sodium tetraethylborate and nonane is shown to shorten the sample preparation time for gas chromatographic determination of organotin compounds in biological materials. After a 3-min reaction time, ethyl derivatives of mono-, di-, and tributyltin, and triphenyltin are quantitatively (>95%) found in the supernatant organic phase that is injected onto a capillary GC column. Two rapid one-step analytical procedures, using flame photometric and atomic emission detection, respectively, were developed on this basis and validated by analyzing the NIES11 certified reference fish tissue.     

Toward single-calibrant quantification in HPLC. A comparison of three detection strategies: evaporative light scattering, chemiluminescent nitrogen, and proton NMR

There is an urgent need for detection technologies that enable accurate and precise quantification of solutions containing small organic molecules in a manner that is rapid, cheap, non-labor-intensive, readily automated, and without a requirement for specific analyte standards. We provide a theoretical analysis that predicts that the logarithmic nature of the working domain of the evaporative light-scattering detector (ELSD) will normally bias toward underestimation of chromatographically resolved impurities, resulting in an overestimation of analyte purity. This analysis is confirmed by experiments with flow injection analysis (FIA) and gradient reversed-phase high performance liquid chromatography (RP-HPLC). Quantification is further compromised by the dependence of response parameters on the matrix composition and hence on the retention time of the analyte. Attempts were made to ameliorate these problems by using the response surface of a single compound to calibrate throughout the HPLC gradient. A chemiluminescent nitrogen detector (CLND) was also used in a similar manner, and the performance of the two techniques were compared against those of each other and that of a reference standard technique. A protocol for this purpose was developed using proton nuclear magnetic resonance (1H NMR) and the ERETIC method to enable quantification by integrating proton signals. The double-blind comparison exercise confirmed molar nitrogen CLND response to be sufficiently stable and robust across a methanol gradient to be used with a single external nitrogenous calibrant to quantify nitrogen-containing compounds of known molecular formula. The performance of HPLC-CLND was very similar to that of NMR, while that of HPLC-ELSD was seen to be significantly worse, showing it to be unsuitable for the purpose of single-calibrant quantification. We report details and experience of our use of RP-HPLC-CLND-MS to characterize and quantify small amounts of solutions of novel compounds at nominal levels of 10mM in microtiter plate (MTP) format.     

Evaluation of an ultrasonic acid digestion procedure for total heavy metals determination in environmental and biological samples

In this study, a sample preparation method based on ultrasonic assisted acid digestion (UAD) has been evaluated for total heavy metals (Cd, Cr, Ni and Pb) determination in different environmental (soil, sediment and sewage sludge), and biological (fish muscles, vegetables and grains) samples, using electrothermal atomic absorption spectrometry (ETAAS). The investigated parameters influencing UAD such as presonication time, sonication time, temperature of ultrasonic bath, and different acid mixtures were fully optimized, whereas power was maintained constant at 100% of nominal power of ultrasonic bath. Six different sets of above parameters were applied on six certified reference materials (CRMs) having different matrices. The accuracy of the method was also tested by comparing the results with those obtained from conventional hot plate assisted acid digestion method on same CRMs. Analytical results for HMs by both methods showed no significant difference at 95% confidence limit (p<0.05). Recoveries of HMs ranging from 96.2% to 102% and 96.3% to 98.6% were obtained from biological and environmental samples, respectively. The average relative standard deviation of UAD method varied between 3.5% and 8.2%, depending on the analyte.     

Determination of cabergoline by electrospray ionization tandem mass spectrometry: picogram detection via column focusing sample introduction.

An electrospray ionization tandem mass spectrometric method was developed for low-picogram detection of an ergot alkaloid, cabergoline, in coyote plasma extracts. Cabergoline is under investigation as an abortifacient in canid species. Central to the successful development of this method was the ability to introduce relatively large sample volumes into the mass spectrometer. This was achieved by focusing the analyte on a conventional high-performance liquid chromatography guard column prior to elution into the spectrometer. Volumes up to at least 900 microL could be injected onto the guard column using a 100% aqueous mobile phase. Cabergoline retained on the column was eluted as a discreet band into the mass spectrometer by the rapid addition of methanol (30%) to the mobile phase. As compared to flow injection sample introduction, the ability to inject larger sample volumes led to a greatly lowered detection limit. Using this technique and a modification of a previously reported extraction procedure, cabergoline could be determined in coyote plasma at concentrations as low as 9 pg of cabergoline/mL of plasma.     

粮食中营养成分标准物质制备技术

介绍粮食中营养成分基体标准物质的制备方法和流程,包括总的原则、成分设计、基体选择、物料采集、物料处理、成分初测、粉碎、筛分烘干过程、均匀性初检、分装、辐照灭菌、真空包装及储存。重点讨论和分析制备过程中应注意的细节以及为了保证均匀性和稳定性所采取的措施。     

Certified reference materials of trace elements in water

Measurement of trace elements is playing a vital role in industries and various sectors of science and technology including semiconductors, food, health and environmental sectors. In most of the cases a small error in measurement can vitiate all the measures taken for quality control and management. Many decisions regarding the suitability of material/products are based on the analysis. To reduce or eliminate the rejection rate of the products, accurate and reliable measurements are needed which can be achieved by the use of certified reference materials (CRMs). Their use in calibration of analytical equipments and validation of test methods ensures high quality in measurements and it provides traceability to the measurement data with national/international measurement systems (SI unit) also. In the present scenario of globalization of economy, use of certified reference materials (CRMs) in measurements is essential for global acceptance of products and test reports. Their use fulfil a mandatory requirement of international quality systems (ISO 9000, ISO/IEC standard 17025) including our national accreditation body, National Accreditation Board for Testing and Calibration Laboratories (NABL), World Trade Organization (WTO) etc. International manufacturers of CRMs are meeting most of the requirement of CRMs of the country. To meet the demand of CRMs indigenously, the National Physical Laboratory, India initiated a national programme on preparation and dissemination of certified reference materials.     

Stop-flow programmable selectivity with a dual-column ensemble of microfabricated etched silicon columns and air as carrier gas

A series-coupled ensemble of microfabricated GC columns made by dry reactive ion etching of silicon substrates is evaluated for use with pneumatic selectivity enhancement techniques for targeted pairs of volatile organic compounds. Each column is 3.0 m long with a 150 miceom wide by 240 microm deep cross section. Dynamic coating was used to prepare a nonpolar column with a dimethyl polysiloxane stationary phase and a moderately polar column with a trifluoropropylmethyl polysiloxane stationary phase. Each column generates 5000-6000 theoretical plates. The columns are operated in series with the nonpolar column connected to a split inlet, the polar column connected to a flame ionization detector, and a valve connected between the column junction point and the inlet to the first column. When the valve is closed, the effluent from the first column passes directly into the second column. When the valve is open, both ends of the first column are at the inlet pressure, and flow stops in this column while increased flow is obtained in the second column. For analyte pairs that are separated by the first column but coelute from the column ensemble, the valve is opened for a few seconds after the first component of the pair has passed into the second column but the second component is still in the first column. The result is enhanced separation of the pair in the ensemble chromatogram. Relatively thick cross-linked stationary-phase films are used to increase retention for volatile compounds. The combination of air carrier gas and stationary-phase film thickness in the range 1-2 microm requires the use of relatively low average carrier gas velocities (typically less than 10 cm/s) for adequate resolving power of the column ensemble. Selectivity enhancement under isothermal conditions for a 14-component mixture of volatile organic compounds is demonstrated where neither of the columns alone nor the column ensemble without selectivity enhancement could obtain a complete separation.     

Cloud point extraction coupled with microwave or ultrasonic assisted back extraction as a preconcentration step prior to gas chromatography

Cloud point extraction of nonionic and anionic surfactants was applied as a preconcentration step prior to gas chromatography. No cleanup step preceded chromatographic analysis. The obtained surfactant-rich phase was treated with water-immiscible solvents, and the target analytes were back extracted by short-term microwave application or ultrasonication. A mixture of six PAHs (naphthalene, acenaphthene, fluorene, anthracene, fluoranthene, pyrene) was used as test compounds. The obtained detection limits were in the microgram per liter area. Recoveries of spiked water and soil samples ranged between 92 and 105% while analysis of certified reference materials gave results in good agreement with the certified values. Under the optimum experimental conditions, there was no interference or blocking of the column. According to our results, this approach presents a convenient solution to the up-to-date problem of combining gas chromatography with micellar cloud point extraction.     

A preconcentration system for determination of copper and nickel in water and food samples employing flame atomic absorption spectrometry

A separation/preconcentration procedure using solid phase extraction has been proposed for the flame atomic absorption spectrometric determination of copper and nickel at trace level in food samples. The solid phase is Dowex Optipore SD-2 resin contained on a minicolumn, where analyte ions are sorbed as 5-methyl-4-(2-thiazolylazo) resorcinol chelates. After elution using 1 mol L(-1) nitric acid solution, the analytes are determinate employing flame atomic absorption spectrometry. The optimization step was performed using a full two-level factorial design and the variables studied were: pH, reagent concentration (RC) and amount of resin on the column (AR). Under the experimental conditions established in the optimization step, the procedure allows the determination of copper and nickel with limit of detection of 1.03 and 1.90 microg L(-1), respectively and precision of 7 and 8%, for concentrations of copper and nickel of 200 microg L(-1). The effect of matrix ions was also evaluated. The accuracy was confirmed by analyzing of the followings certified reference materials: NIST SRM 1515 Apple leaves and GBW 07603 Aquatic and Terrestrial Biological Products. The developed method was successfully applied for the determination of copper and nickel in real samples including human hair, chicken meat, black tea and canned fish.     

Selective detection of volatile aromatic compounds using a compact laser ionization detector with fast gas chromatography

We report results for a new gas chromatography detector that is comparatively sensitive and far more selective for aromatic compounds than the traditional photoionization detector. The detection means is multiphoton ionization at atmospheric pressure. The ionization source in these experiments is a diode-pumped passively Q-switched microchip laser operating at 266 nm. Experiments were conducted with the detector interfaced to a fast gas chromatograph. For <20 s elution time, limits of detection were <1 pg for toluene, ethylbenzene, xylenes, and isopropylbenzene; the limit of detection for benzene is approximately 10 pg. Detector response was linear over 5 orders of magnitude, including these low levels. Negligible signals were observed for nonaromatic ketones, aldehydes, ethers, and cycloalkanes at levels as high as 0.1 microg (10 mg/L concentration). Detector efficiency after fast GC separation was 0.002% when using a detector cell with a radius of 1.1 cm and a purge gas flow of 500 mL/min. The advantages of this detector are further illustrated by the fast GC analysis of fuel samples.     

系列液体和固体水分标准物质的研制

针对水分检测领域对标准物质的需要,研制了系列水分标准物质,包括4种液体水分标准物质,量值覆盖范围为0.139~47.6 mg/g,不确定度范围为0.012~1.1 mg/g;还包括3种含结晶水化合物水分标准物质,量值覆盖范围为50.7~156.3 mg/g,不确定度范围为0.6~1.3 mg/g,以及3种混合物水分标准物质,量值覆盖范围为0.142~9.90 mg/g,不确定度范围为0.013~0.20 mg/g。该系列液体和固体水分标准物质,适用于卡尔·费休库仑法和容量法水分仪的校准和检定,以及水分测量方法的验证,能够保障我国水分检测的量值准确和等效一致。