Mechanical characterization of hierarchical carbon fiber/nanofiber composite laminates

Susceptibility to matrix driven failure is one of the major weaknesses of continuous-fiber composites. In this study, helical-ribbon carbon nanofibers (CNF) were dispersed in the matrix phase of a continuous carbon fiber-reinforced composite. Along with an unreinforced control, the resulting hierarchical composites were tested to failure in several modes of quasi-static testing designed to assess matrix-dominated mechanical properties and fracture characteristics. Results indicated CNF addition offered simultaneous increases in tensile stiffness, strength and toughness while also enhancing both compressive and flexural strengths. Short-beam strength testing resulted in no apparent improvement while the fracture energy required for the onset of mode I interlaminar delamination was enhanced by 35%. Extrinsic toughening mechanisms, e.g., intralaminar fiber bridging and trans-ply cracking, significantly affected steady-state crack propagation values. Scanning electron microscopy of delaminated fracture surfaces revealed improved primary fiber–matrix adhesion and indications of CNF-induced matrix toughening.     

Enhancement of mechanical performance of epoxy/carbon fiber laminate composites using single-walled carbon nanotubes

Carbon nanotubes (CNT) in their various forms have great potential for use in the development of multifunctional multiscale laminated composites due to their unique geometry and properties. Recent advancements in the development of CNT hierarchical composites have mostly focused on multi-walled carbon nanotubes (MWCNT). In this work, single-walled carbon nanotubes (SWCNT) were used to develop nano-modified carbon fiber/epoxy laminates. A functionalization technique based on reduced SWCNT was employed to improve dispersion and epoxy resin-nanotube interaction. A commercial prepregging unit was then used to impregnate unidirectional carbon fiber tape with a modified epoxy system containing 0.1 wt% functionalized SWCNT. Impact and compression-after-impact (CAI) tests, Mode I interlaminar fracture toughness and Mode II interlaminar fracture toughness tests were performed on laminates with and without SWCNT. It was found that incorporation of 0.1 wt% of SWCNT resulted in a 5% reduction of the area of impact damage, a 3.5% increase in CAI strength, a 13% increase in Mode I fracture toughness, and 28% increase in Mode II interlaminar fracture toughness. A comparison between the results of this work and literature results on MWCNT-modified laminated composites suggests that SWCNT, at similar loadings, are more effective in enhancing the mechanical performance of traditional laminated composites.     

Interlaminar and intralaminar reinforcement of composite laminates with aligned carbon nanotubes

Three-dimensional reinforcement of woven advanced polymer–matrix composites using aligned carbon nanotubes (CNTs) is explored experimentally and theoretically. Radially-aligned CNTs grown in situ on the surface of fibers in a woven cloth provide significant three-dimensional reinforcement, as measured by Mode I interlaminar fracture testing and tension-bearing experiments. Aligned CNTs bridge the ply interfaces giving enhancement in both initiation and steady-state toughness, improving the already tough system by 76% in steady state (more than 1.5 kJ/m² increase). CNT pull-out on the crack faces is the observed toughening mechanism, and an analytical model is correlated to the experimental fracture data. In the plane of the laminate, aligned CNTs enhance the tension-bearing response with increases of: 19% in bearing stiffness, 9% in critical strength, and 5% in ultimate strength accompanied by a clear change in failure mode from shear-out failure (matrix dominated) without CNTs to tensile fracture (fiber dominated) with CNTs.     

Development of sizing-free multi-functional carbon fibre nanocomposites

High quality multi-walled carbon nanotubes (CNTs) grown at high density using a low temperature growth method are used as an alternative material to polymer sizing and is utilised in a series of epoxy composites reinforced with carbon fibres to provide improved physical and electrical properties. We report improvements for sizing-sensitive mechanical and physical properties, such as the interfacial adhesion, shear properties and handling of the fibres, whilst retaining resin-infusion capability. Following fibre volume fraction normalisation, the carbon nanotube-modified carbon fibre composite offers improvements of 146% increase in Young’s modulus; 20% increase in ultimate shear stress; 74% increase in shear chord modulus and an 83% improvement in the initial fracture toughness. The addition of CNTs imparts electrical functionalisation to the composite, enhancements in the surface direction are 400%, demonstrating a suitable route to sizing-free composites with enhanced mechanical and electrical functionality.     

Enhancement of mechanical properties of natural fiber composites via carbon nanotube addition

The effects of carbon nanotubes (CNTs) on the mechanical and fracture properties of ramie fiber-reinforced epoxy composites were investigated. Three-point bending, short beam shear, single-edge-notch bending, and Charpy impact tests were employed to evaluate the properties of ramie fiber-reinforced composites without and with CNTs modification. The fracture mechanisms were revealed with the aid of the dynamic mechanical analysis, Fourier transform infrared, and X-ray photoelectron spectroscopy. It was found that the mechanical and fracture properties of ramie fiber-reinforced composites were enhanced by incorporating multiwalled carbon nanotubes, except the impact fracture toughness. The unique chemical compositions and the multiscaled nanosized microstructures of natural fibers brought into focus new mechanisms for the improvement of the mechanical properties of natural fiber-reinforced composites.     

Multi-scale reinforcement of CFRPs using carbon nanofibers

In this paper, stacked-cup carbon nanofibers (CNF) were dispersed in the matrix phase of carbon-fiber-reinforced composites based on a high-performance epoxy system with and without modification by an elastomeric triblock copolymer (TCP) for increased toughness. The addition of the TCP provided an enhancement in toughness at the cost of a slight degradation in modulus and strength. The CNFs, on the other hand, provided significantly enhanced strength and stiffness in matrix-dominated configurations, including tension of quasi-isotropic composites and short beam shear strength of both quasi-isotropic and unidirectional composites. Scanning electron microscopy revealed enhanced adhesion between the matrix and carbon fibers with the addition of either TCP or CNFs. However, CNF agglomeration in the studied systems partially offset the energy dissipation processes brought about by the nanofibers, thereby limiting interlaminar fracture toughness enhancements by CNF addition. These results show good promise for CNFs as low-cost reinforcement for composites while offering insight into the codependent morphologies of multi-scale phases and their influence over bulk properties.     

Carbon and glass hierarchical fibers: Influence of carbon nanotubes on tensile,flexural and impact properties of short fiber reinforced composites

Dense carbon nanotubes (CNTs) were grown uniformly on the surface of carbon fibers and glass fibers to create hierarchical fibers by use of floating catalyst chemical vapor deposition. Morphologies of the CNTs were investigated using scanning electronic microscope (SEM) and transmission electron microscope (TEM). Larger diameter dimension and distinct growing mechanism of nanotubes on glass fiber were revealed. Short carbon and glass fiber reinforced polypropylene composites were fabricated using the hierarchical fibers and compared with composites made using neat fibers. Tensile, flexural and impact properties of the composites were measured, which showed evident enhancement in all mechanical properties compared to neat short fiber composites. SEM micrographs of composite fracture surface demonstrated improved adhesion between CNT-coated fiber and the matrix. The enhanced mechanical properties of short fiber composites was attributed to the synergistic effects of CNTs in improving fiber–matrix interfacial properties as well as the CNTs acting as supplemental reinforcement in short fiber-composites.     

Interlaminar Fracture Toughness of Carbon Fibre‐Reinforced Polymer Laminates With Nano‐ and Micro‐Fillers

Abstract: Vapour growth carbon nanofibres (CNF) and lead zirconate titanate (PZT) piezoelectric particles were added in the matrix of carbon fibre‐reinforced polymer laminates. The fracture toughness of the modified composites was measured under mode I and mode II loading and compared with plain epoxy carbon fibre‐reinforced composites. The mode I fracture toughness of the composites improved with the incorporation of the carbon nanofibres and deteriorated with the incorporation of PZT piezoelectric particles. When both fillers were added in the composite matrix, the mode I fracture toughness improved but to a lesser extend. The mode II fracture toughness of the modified composites was improved in all three cases. The aforementioned behaviour was attributed to competing fracture mechanisms instigated by the different fillers, and backed by fractographic evidence from the failed composite coupons; during the tests, the acoustic emission activity of the coupons was monitored and classified in three major energy absorbing mechanisms which were attributed to the failure of distinct composite phases.     

Hybrid carbon nanotube–carbon fiber composites with improved in-plane mechanical properties

In this study carbon nanotubes (CNTs) were grown on carbon fibers to enhance the in-plane and out-of-plane properties of fiber reinforced polymer composites (FRPs). A relatively low temperature synthesis technique was utilized to directly grow CNTs over the carbon fibers. Several composites based on carbon fibers with different surface treatments (e.g. growing CNTs with different lengths and distribution patterns and coating the fibers with a thermal barrier coating (TBC) layer) were fabricated and characterized via on- and off-axis tensile tests. The on-axis tensile strength and ductility of the hybrid FRPs were improved by 11% and 35%, respectively, due to the presence of the TBC and the surface grown CNTs. This configuration also exhibited 16% improvement on the off-axis stiffness. Results suggest that certain CNT growth patterns and lengths are more pertinent than the other surface treatments to achieve superior mechanical properties.     

Failure analysis and the optimal toughness design of carbon nanotube-reinforced composites

The combined analysis of the fracture toughness enhancement of carbon nanotube (CNT)-reinforced composites is herein carried out on the basis of atomistic simulation, shear-lag theory and facture mechanics. It is found that neither longer reinforced CNTs nor stronger CNT/matrix interfaces can definitely lead to the better fracture toughness of these composites. In contrast, the optimal interfacial chemical bond density and the optimal CNT length are those making the failure mode just in the transition from CNT pull-out to CNT break. To verify our theory, an atomic/continuum finite element method (FEM) is applied to investigate the fracture behavior of CNT-reinforced composites with different interfacial chemical bond densities. Our analysis shows that the optimal interfacial chemical bond density for (6,6) CNTs is about 5–10% and that increasing the CNT length beyond 100 nm does not further improve fracture toughness, but can easily lead to the self-folding and clustering of the CNTs. The proposed theoretical model is also applicable to short fiber-reinforced composites.     

Effects of silane-modified carbon nanotubes on flexural and fracture behaviors of carbon nanotube-modified epoxy/basalt composites

We investigated the effects of carbon nanotube (CNT) modification with silane on the flexural and fracture behaviors of modified carbon nanotube epoxy/basalt (CNT/epoxy/basalt) composites. Flexural and mode I fracture tests were performed using acid-treated and silane-treated CNT/epoxy/basalt composites, respectively. FT-IR analysis was conducted to determine the chemical change on the surface of basalt fiber due to the silane modification. After the fracture tests, the fracture surfaces of the CNT/epoxy/basalt composites were examined with scanning electron microscopy (SEM) to investigate the fracture mechanisms of the CNT/epoxy/basalt composites, depending on the CNT modification. The results show that the flexural modulus and strength of silane-treated CNT/epoxy/basalt composites are ～10% and ～14% greater, respectively, than those of acid-treated CNT/epoxy/basalt composites. The fracture toughness G_Ic of silane-treated CNT/epoxy/basalt composites was ～40% greater than that of acid-treated CNT/epoxy/basalt composites. SEM examination revealed that the improvement in the flexural and fracture properties of silane-treated CNT/epoxy/basalt composites occurred due to enhanced dispersion and interfacial interaction between the silane-modified CNTs and the epoxy.     

Interfacial load transfer in carbon nanotube/ceramic microfiber hybrid polymer composites

Growing carbon nanotubes (CNTs) on the surface of fibers has the potential to modify fiber–matrix interfacial adhesion, enhance the composite delamination resistance, and possibly improve its toughness and any matrix-dominated elastic property as well. In the present work aligned CNTs were grown upon ceramic fibers (silica and alumina) by chemical vapor deposition (CVD) at temperatures of 650 °C and 750 °C. Continuously-monitored single fiber composite (SFC) fragmentation tests were performed on pristine as well as on CNT-grown fibers embedded in epoxy. The critical fragment length, fiber tensile strength at critical length, and interfacial shear strength were evaluated. Significant increases (up to 50%) are observed in the fiber tensile strength and in the interfacial adhesion (which was sometimes doubled) with all fiber types upon which CNTs are CVD-grown at 750 °C. We discuss the likely sources of these improvements as well as their implications.     

Interfacially reinforced methylphenylsilicone resin composites by chemically grafting multiwall carbon nanotubes onto carbon fibers

Both silane and multiwall carbon nanotubes (CNTs) were grafted successfully onto carbon fibers (CFs) to enhance the interfacial strength of CFs reinforced methylphenylsilicone resin (MPSR) composites. The microstructure, interfacial properties, impact toughness and heat resistance of CFs before and after modification were investigated. Experimental results revealed that CNTs were grafted uniformly onto CFs using 3-aminopropyltriethoxysilane (APS) as the bridging agent. The wettability and surface energy of the obtained hybrid fiber (CF-APS-CNT) were increased obviously in comparison with those of the untreated-CF. The CF-APS-CNT composites showed simultaneously remarkable enhancement in interlaminar shear strength (ILSS) and impact toughness. Moreover, the interfacial reinforcing and toughening mechanisms were also discussed. In addition, Thermogravimetric analysis and thermal oxygen aging experiments indicated a remarkable improvement in the thermal stability and heat oxidation resistance of composites by the introduction of APS and CNTs. We believe the facile and effective method may provide a novel interface design strategy for developing multifunctional fibers.     

Toughening modification of polycarbonate/poly(butylene terephthalate) blends achieved by simultaneous addition of elastomer particles and carbon nanotubes

Small quantities of maleic anhydride grafted styrene-ethylene-butylene-styrene (SEBS-g-MAH) copolymer and carbon nanotubes (CNTs) were introduced into polycarbonate (PC)/poly(butylene terephthalate) (PBT) blends. The results demonstrated that simultaneously adding SEBS-g-MAH and CNTs greatly enhanced the fracture toughness of the samples and the impact strength increased with increasing CNT content. The morphologies, the dispersion of CNTs, the relaxation behaviors and the crystallization behaviors of samples were systematically investigated. SEBS-g-MAH formed the dispersed particles in the system. The particle diameter was decreased in the blend composites. CNTs exhibited homogeneous dispersion in the blend composites and they also formed a percolated network structure at relatively high content. The transesterification between PC and PBT components was suppressed by SEBS-g-MAH, and the crystallization ability of the PBT component was greatly enhanced. The toughening mechanisms were mainly related to the suppressed transesterification, the decreased elastomer particle size, and the formation of a CNT network structure.     

Fracture behavior of carbon nanotube/carbon microfiber hybrid polymer composites

Growing carbon nanotubes (CNTs) on the surface of fibers has the potential to modify fiber–matrix interfacial adhesion, enhance composite delamination resistance, and possibly improve toughness. In the present study, aligned CNTs were grown upon carbon fabric via chemical vapor deposition. Continuously monitored single-fiber composite fragmentation tests were performed on pristine and CNT-grafted fibers embedded in epoxy, and single-laminate compact-tension specimens were tested for fracture behavior. A significant increase (up to 20 %) was observed in the interfacial adhesion, at the cost of a decrease in the fiber tensile strength. As a result, the maximum load of the composite was decreased, but its residual load-bearing capacity more than doubled. The likely sources of these effects are discussed, as well as their implications.     

An assessment of the science and technology of carbon nanotube-based fibers and composites

This paper examines the recent advancements in the science and technology of carbon nanotube (CNT)-based fibers and composites. The assessment is made according to the hierarchical structural levels of CNTs used in composites, ranging from 1-D to 2-D to 3-D. At the 1-D level, fibers composed of pure CNTs or CNTs embedded in a polymeric matrix produced by various techniques are reviewed. At the 2-D level, the focuses are on CNT-modified advanced fibers, CNT-modified interlaminar surfaces and highly oriented CNTs in planar form. At the 3-D level, we examine the mechanical and physical properties CNT/polymer composites, CNT-based damage sensing, and textile assemblies of CNTs. The opportunities and challenges in basic research at these hierarchical levels have been discussed.     

Mechanisms for rate effects on interlaminar fracture toughness of carbon/epoxy and carbon/PEEK composites

The objective of this study was to investigate strain-rate dependent energy absorption mechanisms during interlaminar fracture of thermosetting (epoxy) and thermoplastic (PEEK) uni directional carbon fibre (CF) composites. A simple model addressing the translation of matrix toughness to mode I and mode II interlaminar toughness of the composite is presented, in conjunction with a fractographic examination of the fracture surfaces and the fracture process. The observed rate dependency of composite fracture toughness is attributed to the rate dependent toughness of the viscoelastic matrix and the size of the process zone around the crack tip. Other important factors identified are the roughness of the fracture surface and fibre bridging.     

Mechanical and thermal properties of carbon fiber/polypropylene composite filled with nano-clay

The effect of organoclay on the mechanical and thermal properties of woven carbon fiber (CF)/compatibilized polypropylene (PPc) composites is investigated. Polypropylene–organoclay hybrids nanocomposites were prepared using a maleic anhydride-modified PP oligomer (PP-g-MA) as a compatibilizer. Different weight percentages of Nanomer® I-30E nanoclay were dispersed in PP/PP-g-MA (PPc) using a melt mixing method. The PPc/organoclay nanocomposite was then used to manufacture plain woven CF/PPc nanocomposites using molding compression process. CF/PPc/organoclay composites were characterized by different techniques, namely; dynamic mechanical analysis (DMA), fracture toughness and scanning electron microscope. The results revealed that at filler content 3% of organoclay, initiation and propagation interlaminar fracture toughness in mode I were improved significantly by 64% and 67% respectively, which could be explained by SEM at given weight as well; SEM images showed that in front of the tip, fibers pull out during initiation delamination accounting for fracture toughness improvement. Dynamic mechanical analysis showed enhancement in thermomechanical properties. With addition 3 wt.% of organoclay, the glass transition temperature increased by about 6 °C compared to neat CF/PPc composite indicating better heat resistance with addition of organoclay.     

Interfacial adhesion improvement of plain woven carbon fiber reinforced epoxy filled with micro-fibrillated cellulose by addition liquid rubber

In certain application of fiber reinforced polymer composites fracture resistance is required. The aim of this study was to improve the interfacial adhesion between plain woven carbon fiber (CF) and epoxy matrix filled with microfibrillated cellulose (MFC) modified with carboxyl-terminated butadiene acrylonitrile (CTBN) as liquid rubber. CF/Epoxy/MFC/CTBN composite was characterized by different techniques, namely, tensile, bending, fracture toughness (mode I) test, and scanning electron microscope (SEM). The results reveal that at a fiber content 1% of MFC and 10% CTBN, initiation and propagation interlaminar fracture toughness in mode I improved significantly by 96 and 127%, respectively, which could be attribute to strong adhesion between filled epoxy, CF, and rubber. This can be explained by SEM at given weight as well; SEM images showed that in front of the tip, fiber breakage during initiation delimination as well as the extensive matrix deformation between fibers accounting for increase fracture toughness.     

Process and mechanical properties of carbon/carbon–silicon carbide composite reinforced with carbon nanotubes grown in situ

A hierarchical C_f/C–SiC composite was fabricated via in situ growth of carbon nanotubes (CNTs) on fiber cloths following polymer impregnation and pyrolysis process. The effects of CNTs grown in situ on mechanical properties of the composite, such as flexural strength, fracture toughness, crack propagation behavior and interfacial bonding strength, were evaluated. Fiber push-out test showed that the interfacial bonding strength between fiber and matrix was enhanced by CNTs grown in situ. The propagation of cracks into and in fiber bundles was impeded, which results in decreased crack density and a “pull-out of fiber bundle” failure mode. The flexural strength was increased while the fracture toughness was not improved significantly due to the decreased crack density and few interfacial debonding between fiber and matrix, although the local toughness can be improved by the pull-out of CNTs.