W-30Cu纳米复合粉末液相烧结致密化与晶粒长大机制

采用喷雾干燥-煅烧、还原工艺制备超细W-30Cu复合粉末,将粉末模压成形,在1340～1420℃液相烧结15～120min,研究其致密化行为及晶粒长大机制。结果表明:W-30Cu复合粉末在液相烧结早期发生了显著的致密化,1340℃烧结15 min致密度可达到90%以上;随烧结时间的延长致密度增加,1380℃烧结90 min相对密度达到99.1%。液相烧结过程中,W晶粒不断长大并逐渐球化,且其晶粒大小G与烧结时间t符合G3∝kt关系,服从液相烧结溶解-析出机制。烧结温度对W晶粒长大影响显著,当温度从1340℃上升到1420℃时,其晶粒长大动力学系数从1.61×10-2μm3/min增大到4.65×10-2μm3/min,液相的形成、颗粒重排、溶解-析出及W晶粒长大使细晶W-Cu获得近全致密。     

溶胶-喷雾干燥超细/纳米晶W-20Cu复合粉末的烧结行为

采用喷雾干燥-氢气还原法制备超细/纳米晶W-20Cu(质量分数,%)复合粉末,粉末压坯直接从室温推入高温区烧结不同时间后直接取出水淬,研究其烧结致密化和显微组织的变化。结果表明,超细/纳米晶W-20Cu粉末在1000～1200℃烧结时发生迅速致密化。粉末压坯在1200℃烧结60min,其材料致密度已达到96.4%。1420℃烧结90min时致密度达到99%以上。1100～1420℃烧结时其烧结致密化活化能不断减小,从1100℃时的276.3kJ/mol减小到1420℃时的29.1kJ/mol。当温度低于1200℃时,W晶粒长大不明显,当温度超过1300℃时,W晶粒开始有明显长大。随温度的升高W晶粒发生显著球形化,1420℃烧结时发现其晶粒长大符合G3=kt的Ostwald机制,此时晶粒长大动力学系数K仅为0.024μm3/min。     

纳米晶W-Cu复合粉末烧结行为

研究了机械合金化制备的纳米晶W-xCu(x=15,20,25)复合粉末的烧结行为.结果表明,纳米晶W-Cu复合粉末烧结致密化强烈地依赖于烧结温度与烧结时间.当烧结温度从1 150℃提高到1 200℃时,烧结30min后的烧结体相对密度由91%～94%增加到97%～98%;当烧结温度超过1 300℃时,烧结体发生快速致密化,5 min内相对密度即可达到98%左右.研究还发现,W-Cu合金中W晶粒尺寸也强烈地依赖于烧结温度,即烧结温度愈高,W晶粒长大愈显著.当压坯在1 200～1 250℃烧结30 min后,所得到的晶粒度约为300～500 nm,其中经1 200℃烧结时的晶粒尺寸约为300～350 nm.另外,Cu含量增加有利于烧结致密化,并降低W晶粒长大的趋势.     

纳米晶Mo-Cu复合粉末烧结行为的研究

采用溶胶-喷雾干燥-煅烧-氢气还原的方法制备了纳米晶Mo-18Cu、Mo-30Cu、Mo-40Cu复合粉末,研究了纳米晶Mo-Cu粉末的烧结行为以及Cu含量对致密化的影响.结果表明,纳米晶Mo-Cu复合粉末致密化程度高,速度快,在1050～1200 ℃烧结,Mo-30Cu和Mo-40Cu的相对密度可达98%以上,且合金晶粒细小,而Mo-18Cu在1350 ℃以上烧结,相对密度也可达98%以上,但晶粒聚集长大到5 μm左右.研究发现Mo-Cu复合粉末形成了亚稳态的超饱和Mo(Cu)固溶体,随着烧结温度的升高,Cu相逐渐从亚稳态的超饱和Mo(Cu)固溶体颗粒中析出.     

纳米晶WC-10Co复合粉末的烧结致密化行为

研究了机械合金化纳米晶WC-10Co复合粉末的真空烧结致密化行为和一般规律.结果表明:烧结温度的提高和烧结时间的延长有利于样品的烧结致密化过程,在1 275～1 300℃致密化速度快,在1 300℃,15 min左右致密化过程已基本完成;VC、Cr3C2等复合晶粒长大抑制剂含量的增加不利于致密化过程;新型晶粒长大抑制剂A可以更有效地阻碍晶粒长大;纳米晶WC-10Co-0.8VC/Cr3C2-0.2A复合粉末压坯在1375℃,30min烧结条件下,所得的密度为14.48 g/cm3,晶粒尺寸约为180 nm.     

不同烧结温度下超细合金烧结体的密度、钴磁和晶粒度

本文研究了钴质量分数为10.5%的超细硬质合金在不同的烧结温度下的致密度、钴磁、晶粒长大等方面的变化趋势。研究结果表明:含量为10.5%的超细硬质合金,当烧结温度达到1 350℃时合金已基本致密化;在经典的WC-Co伪二元状态图表明的固相烧结阶段,随着温度升高,钴磁降低,晶粒长大以并合方式为主,可能存在少许的溶解-析出现象;在液相烧结阶段,钴磁达到稳定值后基本不变,晶粒长大以溶解-析出为主。     

微量Y2O3对细晶W-Ni-Fe粉末烧结行为和显微组织的影响

采用喷雾干燥-热还原的方法制备纳米级93W-4.9Ni-2.1Fe复合粉末和微量稀土掺杂的复合粉末,研究微量稀土掺杂对烧结致密化和晶粒尺寸的影响.结果表明:微量稀土掺杂能有效地降低该复合粉末的晶粒尺寸,并能改善粉末的分散度;纳米级复合粉末在1380～1410℃液相烧结可实现材料的近全致密化,比同种成分的传统钨合金的烧结温度降低了120℃左右,合金的相对密度可达99%以上;但微量稀土掺杂对烧结的致密化有一定的抑制作用;同时微量稀土元素对合金的晶粒尺寸的抑制作用主要发生在液相烧结阶段.     

90W-7Ni-3Fe纳米晶粉末的瞬时液相强化烧结特征

采用机械合金化(MA)制备了晶粒尺寸为8～18 nm的90W-7Ni-3Fe纳米晶粉末(MA粉末).将粉末注射成形,在1 480～1 500℃经3～5 min瞬时液相烧结.结果表明,采用瞬时液相强化烧结可以得到W晶粒为3～8 μm近全致密的细晶钨合金,显微组织为细小的球形W晶粒均匀地连续分布在纤维状粘结相中,烧结坯具有好的拉抻性能.长时间的传统液相烧结使球状W晶粒迅速粗化,而且密度和强度下降,但延伸率反而增加.在MA粉末中添加微量Y2O3后采用瞬时液相烧结,可以使合金抗拉强度提高到1 055 MPa,延伸率提高到16.5%.     

Mo_2FeB_2基金属陶瓷烧结过程中显微组织和力学性能的变化

采用真空烧结法制备了Mo2FeB2基金属陶瓷。运用XRD、SEM、EDS研究了Mo2FeB2基金属陶瓷的烧结过程中显微组织的变化并测试了不同烧结温度下所得金属陶瓷材料的力学性能。实验结果表明:进入L1液相(奥氏体+Fe2B)烧结阶段后,金属陶瓷由于颗粒重排致密度大幅度提高,但溶解-析出过程进行得较缓慢,晶粒基本没有长大。提高烧结温度至L2液相(奥氏体+L1+Mo2FeB2)生成后,由于溶解-析出过程明显加剧,晶粒长大趋势明显,但致密化程度进一步提高。当烧结温度达到1280℃,保温时间为40min时,烧结体接近完全致密,所得材料组织均匀具有较佳力学性能。     

纳米级90W-7Ni-3Fe复合粉末的低温烧结机制

采用DTA研究了喷雾干燥-H2还原法制备的纳米级90W-7Ni-3Fe复合粉末随温度升高时熔点和相的变化,依此为根据研究了试样在不同烧结温度和不同烧结时间下的烧结特性.采用扫描电子显微镜和金相仪分别对试样断口进行了形貌观察和W晶粒测试,并对烧结样的性能进行了测定与分析.研究结果表明:保温时间为120 min时,随着烧结温度的提高,试样的性能有显著的变化,当烧结温度为1390℃时,试样的抗拉强度、延伸率和相对密度都达到一个极大值,分别为888.3 MPa,12.9%和99.0%;当烧结温度为1390℃时,随烧结时间的延长,试样的性能也有显著的变化,试样的抗拉强度、延伸率和相对密度在保温120 min时都达到一个极大值;平均W晶粒度为20 μm,W晶粒呈球形或近球形;复合粉末烧结活性高,比传统烧结温度降低80℃;粉末中高的氧含量和在干氢中的烧结,使得试样在液相烧结时容易出现孔洞和气泡,W晶粒和粘结相分布不均匀,致使试样力学性能偏低.     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。