Hydrothermal synthesis and photoluminescence properties of Gd2Zr2O7:Tb phosphors

This paper presents hydrothermal synthesis, characterization, and photoluminescence (PL) properties of novel green-emitting phosphors, Gd₂Zr₂O₇:Tb³⁺. Their crystal structure, morphology and photoluminescence properties were investigated by X-ray powder diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM) and fluorescence spectrophotometer. The results revealed that one-dimensional Gd₂Zr₂O₇:Tb³⁺ nanorods with diameter of about 30 nm and length of 150-300 nm were formed, and the products exhibited a fluorite-type structure. PL study revealed that Gd₂Zr₂O₇:Tb³⁺ phosphors presented dominant green emission luminescence, which was attributed to the transitions from ⁵D₄ excited states to ⁷F_J (J = 3-6) ground states of Tb³⁺. The luminescence intensity of Gd₂Zr₂O₇:Tb³⁺ with different Tb³⁺ concentration was also investigated and reported, and an obvious concentration quenching was observed when Tb³⁺ ion concentration was 5 at.%.     

Hydrothermal synthesis and luminescent properties of Y2O3:Tb and Gd2O3:Tb microrods

One-dimensional (1D) Y₂O₃:Tb³⁺ and Gd₂O₃:Tb³⁺ microrods have been successfully prepared through a large-scale and facile hydrothermal method followed by a subsequent calcination process in N₂/H₂ mixed atmosphere. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (IR), thermogravimetric analysis (TGA), energy-dispersive X-ray spectra (EDX), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), photoluminescence (PL) and cathodoluminescence (CL) spectra as well as kinetic decays were used to characterize the samples. The as-formed products via the hydrothermal process could transform to cubic Y₂O₃:Tb³⁺ and Gd₂O₃:Tb³⁺ with the same morphology and slight shrinking in size after a postannealing process. Both Y₂O₃:Tb³⁺ and Gd₂O₃:Tb³⁺ microrods exhibit strong green emission corresponding to ⁵D₄ → ⁷F₅ transition (542 nm) of Tb³⁺ under UV light excitation (307 and 258 nm, respectively), and low-voltage electron beam excitation (1.5 → 3.5 kV), which have potential applications in fluorescent lamps and field emission displays.     

Photoluminescence and energy transfer of terbium doped titania film

Strong visible luminescence of Tb³⁺ions due to intra-4f shell transitions are obtained from Tb³⁺-doped titania (TiO₂) films fabricated by sol-gel method. Based on the overlap of excitation band of Tb³⁺-doped TiO₂ and absorption band of undoped TiO₂, we propose an energy transfer mechanism from TiO₂ host to Tb³⁺ions. Photoluminescence (PL) intensity is found to have a well matching relation with the doping concentration of Tb³⁺ ions. Concentration quenching of PL occurs when Tb³⁺ concentration exceeds a certain value (9.5 mol%). Luminescence intensity is improved obviously after co-doped with Ce³⁺ ions because of the sensitization effect of Ce³⁺ ions and the dispersion of Tb³⁺ ions in TiO₂ system.     

The effect of Tb doping on the structure and spectroscopic properties of MgAl2O4 nanopowders

In this paper, a modified sol-gel method was employed to prepare nanostructured MgAl₂O₄ spinel powders doped with Tb³⁺ ions and thermally treated at 700 and 1000 °C for 3 h. The structural properties of the prepared at 700 and 1000 °C powders where characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). According to obtained XRD patterns the formation of single-phase spinels after calcination was confirmed. The XRD analyses demonstrated that the powders were single-phase spinel nanopowders with high crystallite dispersion. The Rietveld method was applied to calculate lattice parameters. The averaged spinel particle size was determined to be ∼10 nm for calcination at 700 °C and ∼20 nm at 1000 °C. The emission and excitation spectra measured at room and low temperature (77 K) for the samples calcined at 700 and 1000 °C demonstrated characteristic spectra of Tb³⁺ ions. The effect of MgAl₂O₄:Tb³⁺ grain sizes on luminescence properties was noticed.     

Luminescence of SrGdGa3O7:RE(RE = Eu, Tb) phosphors and energy transfer from Gd to RE

Eu³⁺- and Tb³⁺-activated SrGdGa₃O₇ phosphors were synthesized by the solid-state reaction and their luminescence properties were investigated. Sr(Gd_1 − xEu_x)Ga₃O₇ and Sr(Gd_1 − xTb_x)Ga₃O₇ formed continuous solid solution in the range of x = 0-1.0. Unactivated SrGdGa₃O₇ exhibited a typical characteristic excitation and emission of Gd ion. The SrGdGa₃O₇:xEu³⁺ and SrGdGa₃O₇:xTb³⁺ phosphors also showed the well-known Eu³⁺ and Tb³⁺ excitation and emission. The energy transfer from Gd³⁺ to Eu³⁺ and Tb³⁺ were verified by photoluminescence spectra. The dependence of photoluminescence intensity on Eu³⁺ and Tb³⁺ concentration were also studied in detail and the photoluminescence (PL) intensity of SrGdGa₃O₇:Eu and SrGdGa₃O₇:Tb were compared with commercial phosphors, Y₂O₃:Eu and LaPO₄:Ce,Tb. The luminescence decay measurements showed that the lifetimes of Eu³⁺ and Tb³⁺ were in the range of microsecond. The energy transfer from Gd³⁺ to Tb³⁺ was also observed in decay curve.     

Properties of Gd2O3:Eu, Tb nanopowders obtained by sol-gel process

A significant practical application for nanostructured materials is X-ray medical imagery, because it is necessary to use dense materials in order to enable absorption of high energy photons. An important requirement of these materials is UV-vis range emission produced by X-ray excitation, which can be influenced by the particle size. Europium doped gadolinium oxide is a well known red phosphor. Moreover, nanophosphors of Gd₂O₃ codoped with Tb³⁺, Eu³⁺ increase their light yield by energy transfer between Tb³⁺ and Eu³⁺. In this study, Gd₂O₃ nanopowders codoped with Eu³⁺ and Tb³⁺ (2.5 at.% Eu³⁺, and 0.005 and 0.01 at.% Tb³⁺) were obtained via a sol-gel process using gadolinium pentanedionate as precursor and europium and terbium nitrates as doping sources. In this paper, we report the influence of annealing temperature on the structure, morphology and luminescent properties of Gd₂O₃:Eu³⁺, Tb³⁺ by means of TGA, XRD, TEM and X-ray emission measurements.     

Sol–gel synthesis,characterization and luminescent properties of Tb doped MLa2O4 (M = Sr or Ba) nanophosphors

Tb³⁺ doped SrLa₂O₄ and BaLa₂O₄ nanophosphors were successfully synthesized via tartaric acid assisted sol–gel method and their luminescent properties were investigated. The crystal structure and morphology of SrLa₂O₄:Tb³⁺ and BaLa₂O₄:Tb³⁺ was studied by X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscope (TEM). Thermal decomposition behavior of the dried gels was investigated by thermogravimetry (TG) and differential thermal analysis (TGA). Photoluminescence (PL) behaviors of these nanophosphors were checked by the excitation and emission spectra. These SrLa₂O₄ and BaLa₂O₄ nanophosphors displayed green color under a UV source due to characteristic transition of Tb³⁺ from ⁵D₄ → ⁷F₅ at 544 nm. The dependence of photoluminescence intensity on Tb³⁺ ion concentration, tartaric acid concentration and annealing temperature were also studied in detail. In addition, the optimum doping concentration and time-resolved luminescence spectroscopy were also investigated.     

Luminescent properties of Gd2Ti2O7: Eu phosphor films prepared by sol-gel process

Gd₂Ti₂O₇: Eu³⁺ thin film phosphors were fabricated by a sol-gel process. X-ray diffraction (XRD), atomic force microscopy (AFM) and photoluminescence (PL) spectra as well as lifetimes were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 800 °C and the crystallinity increased with the elevation of annealing temperatures. Uniform and crack free phosphor films were obtained, which mainly consisted of grains with an average size of 70 nm. The doped Eu³⁺ showed orange-red emission in crystalline Gd₂Ti₂O₇ phosphor films due to an energy transfer from Gd₂Ti₂O₇ host to them. Both the lifetimes and PL intensity of the Eu³⁺ increased with increasing the annealing temperature from 800 to 1000 °C, and the optimum concentrations for Eu³⁺ were determined to be 9 at.%. of Gd³⁺ in Gd₂Ti₂O₇ film host.     

Preparation and studies of Eu and Tb co-doped Gd2O3 and Y2O3 sol-gel scintillating films

Eu³⁺ (2.5 at.%) and Tb³⁺ (0.005-0.01 at.%) co-doped gadolinium and yttrium oxide (Gd₂O₃ and Y₂O₃) powders and films have been prepared using the sol-gel process. High density and optical quality thin films were prepared with the dip-coating technique. Gadolinium (III) 2,4-pentadionate and yttrium (III) 2,4-pentadionate were used as precursors, and europium and terbium in their nitrate forms were used as doping agents. Chemical and structural analyses (infrared spectroscopy, X-ray diffraction and high-resolution transmission electron microscopy) were conducted on both sol-gel precursor powders and dip-coated films. The morphology of thin films heat-treated at 700 °C was studied by means of atomic force microscopy. It was shown that the highly dense and very smooth films had a root mean roughness (RMS) of 2 nm ± 0.2 (A = 0.0075 Tb³⁺) and 24 nm ± 3.0 (B = 0.01 Tb³⁺). After treatment at 700 °C, the crystallized films were in the cubic phase and presented a polycrystalline structure made up of randomly oriented crystallites with grain sizes varying from 20 to 60 nm. The X-ray induced emission spectra of Eu³⁺- and Tb³⁺-doped Gd₂O₃ and Y₂O₃ powders showed that Tb³⁺ contents of 0.005, 0.0075 and 0.01 at.% affected their optical properties. Lower Tb³⁺ concentrations (down to 0.005 at.%) in both systems enhanced the light yield.     

A novel green luminescent material AlPO4:Tb

A novel green phosphor Tb³⁺ doped AlPO₄ was synthesized by conventional solid-state reaction method. The phosphor showed prominent luminescence in green due to the ⁵D₄-⁷F₅ transition of Tb³⁺. Structural characterization of the luminescent material was carried out with X-ray powder diffraction (XRD) analysis. The XRD measurements indicated that there are no crystalline phases other than AlPO₄. Luminescence properties were analyzed by measuring the excitation and photoluminescence spectra. Photoluminescence measurements indicated that the phosphor exhibited bright green emission at about 542 nm under UV excitation. It is shown that the 3 mol% of doping concentration of Tb³⁺ ions in AlPO₄:Tb³⁺ phosphor is optimum. The measured chromaticity for the phosphors AlPO₄:Tb³⁺ under UV excitation is (0.32, 0.53).     

(Eu-Nb)-codoped TiO2 nanopowders synthesized via Ar/O2 radio frequency thermal plasma oxidation processing: Phase composition and photoluminescence properties through energy transfer

(Eu³⁺-Nb⁵⁺)-codoped TiO₂ nanopowders have been prepared by Ar/O₂ radio frequency (RF) thermal plasma oxidizing liquid precursor mists, with various addition contents of dopants (molar ratio of Eu³⁺:Nb⁵⁺ = 1:1). Characterizations have been performed by the combined studies of XRD, TEM, Raman spectra, UV-vis spectroscopy, and excitation and PL spectra. The plasma-generated nanopowders mainly consist of anatase and rutile polymorphs. Doping Nb⁵⁺ cannot have appreciable influence on Eu³⁺ solubility (0.5 at.%) in the TiO₂ host lattice, but can significantly inhibit the increase of rutile weight fraction for TiO₂. 617 nm PL intensity at 350 nm indirect excitation through energy transfer is considerably weaker than that at 467 nm direct excitation, indicating that a defect state level in the TiO₂ host lattice might be lowered below the excited state of Eu³⁺ by doping Nb⁵⁺, which is conceivable from a relatively large amount of oxygen deficiencies yielded in the TiO₂ host lattice.     

A novel synthetic route to Y2O3:Tb phosphors by bicontinuous cubic phase process

This study applies a novel approach to prepare the terbium-doped yttrium oxide phosphors (Y₂O₃:Tb³⁺) using the bicontinuous cubic phase (BCP) process. The experimental results show that the prepared precursor powder was amorphous yttrium hydroxide Y_1−xTb_x(OH)₃ with a spherical shape and primary size 30–50 nm. High crystallinity phosphors with body-centered cubic structures were obtained after heat treatment above 700 °C for 4 h. The primary size of the phosphors grew to 100–200 nm, and dense agglomerates with a size below 1 μm were formed during the calcination. The obtained Y₂O₃:Tb³⁺ phosphor had a strong green emitting at 542 nm. The optimum Tb³⁺ concentration was 1 mol% to obtain the highest PL intensity. This study indicates that the calcining temperature of 700 °C needed for high luminescence efficiency in this work is much lower than 1000 °C or above needed for the conventional solid-state method.     

Luminescence enhancement of CaZnGe2O6:Tb afterglow phosphors synthesized using ZnO nanopowders

CaZnGe₂O₆:Tb³⁺ afterglow phosphors were prepared by solid state reaction using organic coated ZnO nanopowders and their photoluminescence, X-ray luminescence and afterglow properties were investigated. The CaZnGe₂O₆:Tb³⁺ samples emit a green luminescence at 548 nm attributed to the ⁵D₄-⁷F₅ transition of Tb³⁺. It was observed that the replacement of bulk ZnO by ZnO nanopowder in the sample synthesis increases the luminescence intensity. By adjusting the mass ratio of bulk ZnO to nanopowder ZnO, the photoluminescence intensity, X-ray luminescence intensity, and afterglow efficiency are improved. The optimized sample made with a 0.71 ratio of nano ZnO to bulk ZnO has a factor of four enhancement in X-ray luminescence, photoluminescence and afterglow intensities in comparison with the sample made with 100% bulk ZnO.     

Photoluminescence properties of Y2O3:Tb and YBO3:Tb green phosphors synthesized by hydrothermal method

In this work, two Tb³⁺ activated green phosphors: Y₂O₃:Tb³⁺ and YBO₃:Tb³⁺ were prepared by hydrothermal method. Photoluminescence properties of both phosphors were studied in details. Both phosphors exhibit similar luminescent characteristics symbolized by the dominant green emission at 545 nm. Concentration quenching occurs at the Tb³⁺ concentration of 1.60 atomic% and 2.57 atomic% for Y₂O₃:Tb³⁺ and YBO₃:Tb³⁺, respectively. Luminescence decay properties were characterized to better understand the mechanism of concentration quenching. Based on the calculation, the concentration quenching in both phosphors was caused by the dipole–dipole interaction between Tb³⁺ ions.     

Photoluminescence of Eu-doped TiO2 thin films prepared by low pressure hot target magnetron sputtering

In this work Eu-doped TiO₂ thin films prepared by reactive magnetron co-sputtering of Ti-Eu metallic target have been studied. The results of photoluminescence (PL) and its correlation with microstructure have been described. Structural properties were examined by X-ray diffraction (XRD) and Atomic Force Microscopy (AFM). XRD studies have shown that thin films consisted of TiO₂-anatase and AFM images display their high quality and dense nanocrystalline structure. PL spectra, measured at room temperature, show a dominating strong red luminescence corresponding to ⁵D₀-⁷F₂ transition at ∼ 617 nm and ∼ 623 nm. The evolution of photoluminescence and microstructure of the thin films has been examined as they were additionally annealed in an air ambient.     

The UV and VUV luminescence properties of the phosphor Mg2GeO4:Tb

A novel green phosphor Mg₂GeO₄:Tb³⁺ with pure phase was prepared by the solid state reaction. The luminescence properties were investigated in detail. The diffusion reflection spectra of the undoped and Tb³⁺ doped Mg₂GeO₄ phosphors were recorded, the result reveals that there is an absorption band superposition of the host material and Tb³⁺ ion. The study on the excitation and diffusion spectra shows that there is an effective energy transfer from the host material to Tb³⁺ ion. Under 277 and 172 nm excitation, the phosphor presents predominant green emission at 543 and 547 nm respectively. The excitation intensity at 172 nm is about 1.8 times of that at 272 nm. The promising luminescence properties make it a candidate for application in Plasma Display Panel.     

Synthesis and photoluminescence properties of a new red emitting phosphor: Ca3(VO4)2:Eu; Mn

A new red emitting phosphor, Ca₃(VO₄)₂:Eu³⁺; Mn²⁺, was synthesized by a citric acid sol-gel combustion method and characterized by XRD, TEM and photoluminescence (PL) spectra. The red emission located at about 613 nm was ascribed to ⁵D₀-⁷F₂ transition of Eu³⁺. And the red luminescence intensity changed with annealing temperature and concentration of Eu³⁺. The effect of the co-doped Mn²⁺ was also investigated systematically.     

Energy transfer processes in Ce and Tb co-doped Ln2Si2O7 (Ln = Y, Gd)

The Ce³⁺ and Tb³⁺ co-doped Ln₂Si₂O₇ (Ln = Y, Gd) samples were prepared by sol-gel method. Structure characterization of the phosphor was carried out by X-ray diffraction. The luminescence properties of samples were analyzed by measuring the excitation and emission spectra. It was observed that excitation energy can transfer mutually between Ce³⁺ and Tb³⁺ in GPS: Ce³⁺, Tb³⁺ samples, while in Y₂Si₂O₇ :Ce³⁺, Tb³⁺ samples the energy transfer only progresses from Ce³⁺ to Tb³⁺. Based on the energy level diagrams of respective Ce³⁺, Tb³⁺ and Gd³⁺ ion, the detailed pathways for energy transfer are explained.     

Electron paramagnetic resonance study of rare-earth related centres in K2YF5:Tb thermoluminescence phosphors

Rare-earth related centres have been investigated in K₂YF₅:Tb³⁺ crystals, exhibiting thermoluminescence (TL) below and above room temperature (RT), using electron paramagnetic resonance (EPR) spectroscopy at Q (34 GHz) and W-band (94 GHz). The spectra have been studied prior to irradiation, after exposure in the kGy range to X-rays at 77 K and subsequent pulse annealing up to 570 K. In addition to Gd³⁺, previously studied in detail, we identified Er³⁺ and Yb³⁺ centres as accidental impurities in as-grown crystals and determined their effective g tensors. The EPR spectra of irradiated and annealed crystals provide evidence for the production of at least three distinct Tb-related trapped hole centres, two of which could definitely be identified as Tb⁴⁺. Hence, we prove that the Tb³⁺ activator ions also act as hole traps in K₂YF₅. Pulse annealing experiments indicate that the TL above RT results from thermal release of electrons, recombining at these Tb⁴⁺ ions.     

Characteristics and synthesis mechanism of Gd2O2S:Tb phosphors prepared by vacuum firing method

Characteristics and synthesis mechanism of Gd₂O₂S:Tb phosphors prepared by vacuum firing were investigated by photoluminescence (PL) spectra, X-ray diffraction (XRD), scanning electronic microscopy (SEM) and transmission electron microscopy (TEM). The mixtures of raw materials were tested by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The firing temperature was reduced to about 725 °C by the vacuum firing method. The particle size decreased. Meanwhile the particle size distribution and morphology were improved and the luminescence of Gd₂O₂S:Tb phosphors was also enhanced as the degree of vacuum decreases. With the decrease of the degree of vacuum, the intensity of the excitation spectrum was strengthened and the band was widened being the particle size of the host lattice decreased to nano scales. The peak with high intensity around 272 nm in the excitation spectra (λ_Em = 545 nm) of Gd₂O₂S:Tb nanophosphor may be attributed to the 4d–5f transitions of Gd atoms, which may play a significant role in the energy transfer between Tb³⁺ and Gd³⁺ ions.⁵D₄–⁷F_J transitions of Tb³⁺ ion were mainly concentrated in the narrow green emission spectrum (535–555 nm) with its sharp peak at 545 nm. The synthesis mechanism of Gd₂O₂S:Tb phosphors prepared by vacuum firing was also studied.