Nutrient removal and microbial granulation in an anaerobic process treating inorganic and organic nitrogenous wastewater.

The sustainable anaerobic nitrogen removal and microbial granulation were investigated by using a laboratory anaerobic granular sludge bed reactor, treating synthetic (inorganic and organic) wastewater and piggery waste. From inorganic synthetic wastewater, lithoautotrophic ammonium oxidation to nitrite/nitrate was observed by an addition of hydroxylamine. Also, the results revealed that the Anammox intermediates (particularly, hydrazine) contents in the substrate would be one of the important parameters for success of the anaerobic nitrogen removal process. The results from organic synthetic wastewater show that if the Anammox organism were not great enough in the startup of the process, denitritation and anaerobic ammonification would be a process prior to the Anammox reaction. The anaerobic ammonium removal from the piggery waste was performed successfully, probably due to the Anammox intermediates contained in the substrate. This reactor shows a complex performance including the Anammox reaction and HAP crystallization, as well as having partial denitritation occurring simultaneously. From the activity test, the maximum specific N conversion rate was 0.1 g NH4-N/g VSS/day (0.77 g T-N/g VSS/day), indicating that potential denitritation is quite high. The NO2-N/NH4-N ratio to Anammox is 1.17. The colour of the biomass treating the piggery waste changed from black to dark red. It was also observed that the red-colored granular sludge had a diameter of 1-2 mm. The settleability assessment of the granular sludge revealed that the granular sludge had a good settleability even though it was worse than that of seed granular sludge.     

Post-aeration of anaerobically digested sewage sludge for advanced COD and nitrogen removal: results and cost-benefit analysis at large-scale.

At a large Austrian municipal wastewater treatment plant enhanced stabilisation of anaerobically digested sewage sludge was required in order to get a permit for landfill disposal of the dewatered stabilized sludge. By implementing a post-aeration treatment after anaerobic digestion the organic content of the anaerobically well digested sludge can be decreased by 16%. Investigations at this plant showed that during digested sludge post-aeration anoxic phases are needed to provide stable process conditions. In this way the pH value can be kept in a more favourable range for micro-organisms and concrete structures. Additionally, under the process conditions applied nitrite accumulation would inhibit the stabilisation process if denitrification is not adequately applied. By optimising the aeration/pause ratio approximately 45% of total nitrogen in digested sludge can be removed. NH4-removal occurs through nitrification and denitrification with an efficiency of 98%. This significantly improves nitrogen removal efficiency at the wastewater treatment plant. The costs/benefit analysis shows that post-aeration of digested sludge results in an increase of total annual costs for wastewater treatment of only 0.84%, corresponding to 0.19 Euro/pe/a. Specific costs for nitrogen removal (0.32 Euro/kgN) are comparable with other biological processes for N-removal in reject water.     

Aeration of anaerobically digested sewage sludge for COD and nitrogen removal: optimization at large-scale.

The paper will report about the experiences at an Austrian large wastewater treatment plant of 720,000 population equivalents, where anaerobically digested sewage sludge is further stabilised under aerobic conditions. Enhanced stabilisation of the anaerobically digested sludge was required at the plant in order to get a permit for landfill disposal of the dewatered stabilized sludge. By implementing a post-aeration treatment (SRT approximately 6d; 36 degrees C) after anaerobic digestion the organic content of the anaerobically well digested sludge can be decreased by 16%. Investigations on site showed that during digested sludge post-aeration anoxic phases for denitrification are needed to provide stable process conditions. In this way the pH value can be kept in a more favourable range for micro-organisms and concrete structures. Additionally, inhibition of the biological process due to nitrite accumulation can be avoided. By optimising the aeration/pause ratio approximately 45% of total nitrogen in digested sludge can be removed. This significantly improves nitrogen removal efficiency at the wastewater treatment plant. NH(4)-removal occurs mainly through nitritation and denitritation with an efficiency of 98%. The costs/benefit analysis shows that post-aeration of digested sludge results in an increase of total annual costs for wastewater treatment of only 0.84%, corresponding to 0.19 Euro/pe/a. Result of molecular biological analyses (DGGE) indicate that all four ammonium-oxidizing bacteria species present in activated sludge can survive anaerobic digestion, but only two of them can adapt in the digested sludge post-aeration tanks. Additionally, in the post-aerated digested sludge a further ammonium-oxidizing bacteria species was identified.     

ANAMMOX and partial denitritation in anaerobic nitrogen removal from piggery waste.

The anaerobic ammonium removal from a piggery waste with high strength (56 g COD/L and 5 g T-N/L) was investigated using a lab-scale upflow anaerobic sludge bed reactor at a mesophilic condition. Based on the nitrogen and carbon balance in the process, the contribution of autotrophic and heterotrophic organisms was also evaluated in terms of the influent NO2-N/NH4-N ratio (1:0.8 and 1:1.2 for Phase 1 and Phase 2, respectively). The result of this research demonstrates that the anaerobic ammonium removal from the piggery waste, using the UASB reactor, can be performed successfully. Furthermore, it appears that by using granular sludge as the seed biomass, the ANAMMOX reaction can start more quickly. Average nitrogen conversion was 0.59 kg T-N/m3 reactor-day (0.06 kg T-N/kg VSS/day) and 0.66 kg T-N/m3 reactor-day (0.08 kg T-N/kg VSS/day) for Phase 1 and Phase 2. The NO2-N/NH4-N removal ratio by the ANAMMOX was 1.48 and 1.79 for Phase 1 and Phase 2. The higher nitrite contents (about 50%) in the substrate resulted in higher nitrite nitrogen removal by the partial denitritation, as well as the ANAMMOX reaction, implying higher potential of partial denitritation. However, the result reveals that the ANAMMOX reaction was influenced less by the degree of partial denitritation, and the ANAMMOX bacteria did not compete with denitritation bacteria. The colour of the biomass at the bottom of the reactor changed from dark gray to dark red, which was accompanied by an increase in cytochrome content. At the end of the experiment, red-coloured granular sludge with diameter of 1-2 mm at the lower part of the reactor was also observed.     

Case study on the implementation of deammonification for the process water treatment of Munich WWTPs

The two-staged WWTP 'Gut Grosslappen' has a capacity of 2 mio. PE. It comprises a pre-denitrification in the first stage using recirculation from the nitrifying second stage. A residual post-denitrification in a downstream sand filter is required in order to achieve the effluent standards. Presently the process water from sludge digestion is treated separately by nitrification/denitrification. Due to necessary reconstruction of the biological stages, the process water treatment was included in the future overall process concept of the WWTP. A case study was conducted comparing the processes nitritation/denitrititation and deammonification with nitrification/denitrification including their effect on the operational costs of the planned main flow treatment. Besides the different operating costs the investment costs required for the process water treatment played a significant role. Six cases for the process water treatment were compared. As a result, in Munich deammonification can only be recommended for long-term future developments, due to the high investment costs, compared with the nitritation/denitritation alternative realizable in existing tanks. The savings concerning aeration, sludge disposal and chemicals were not sufficient to compensate for the additional investment costs. Due to the specific circumstances in Munich, for the time being the use of existing tanks for nitritation/denitritation proved to be most economical.     

低负荷下厌氧氨氧化处理养殖废水的启动研究

厌氧氨氧化作为新型生物脱氮技术其关键在于如何实现厌氧氨氧化反应的启动,现有研究多以模拟废水为研究对象,本文以猪场废水为对象的研究,利用ASBR为反应器,接种反硝化污泥培养厌氧氨氧化细菌,在NH+4-N与NO-2-N浓度均为100 mg/L的条件下,运行125 d,经历启动初期、过渡期、系统稳定运行期三个阶段,厌氧氨氧化反应器中NH+4-N的去除率达91.70%,NO-2-N去除率92.0%;NH+4-N的容积负荷为36.90 mg/L.d,NO-2-N的容积负荷为37.55 mg/(L.d),成功实现了厌氧氨氧化反应器的启动。该研究成果对厌氧氨氧化技术在工程实践的应用具有重要的指导意义。     

Nitrogen removal from the saline sludge liquor by electrochemical denitrification.

Sludge liquor from the sludge dewatering process has a high ammonia content. In the present study, a lab-scale electrochemical (EC) system with a pair of Ti electrode plates was used for treating the sludge centrate liquor of digested wastewater sludge with a NH4(+) - N content of around 500 mg/L. The sludge liquor had a high salinity due to seawater being used for toilet flushing in Hong Kong. The results show that the EC process is highly effective for denitrification of the saline sludge liquor. Complete nitrogen removal could be achieved within 1 hr or so. The rate of EC denitrification increased with the current intensity applied. The best current efficiency for nitrogen removal was obtained for a gap distance between the electrodes at 8 mm. Electro-chlorination was considered to be the major mechanism of EC denitrification. The formation of chlorination by-products (CBPs) appeared to be minimal with the total trihalomethanes (THM) detected at a level of 300 microg/L or lower. The power consumption for EC denitrification was around 23 kWh/kg N. Additional electro-flocculation with a pair of iron needle electrodes could enhance the flocculation and subsequent sedimentation of colloidal organics in the sludge liquor, increasing the organic removal from less than 30% to more than 70%. Therefore, the EC process including both electro-denitrification and electro-flocculation can be developed as the most cost-effective method for treatment of the saline sludge liquor.     

Nitrogen removal from digested manure in a simple one-stage process

A process based on partial nitrification and recirculation into the anaerobic digester was studied to remove nitrogen from digested manure and thus reduce enhanced gaseous ammonia emissions due to on-farm biogas production. An anaerobic reactor representing an anaerobic manure digester was fed with a nitrite solution and digested manure liquor. Nitrite was efficiently removed from the influent and ammonium formation was observed first. Ammonium was subsequently eliminated up to a maximum of 90% of the influent concentration, indicating anaerobic ammonium oxidation activity. This activity, however, decreased again and was lost at the end of the 4-month operation period. In a 1.5 L aerobic CSTR that was fed with digested manure liquor, ammonium was efficiently removed from the influent. Nitrite and nitrate formation was observed but mass balances indicated significant N-removal. Accumulation of suspended solids was observed at the end of the experiment suggesting presence of oxygen-free environments. In a second test in a 15 L CSTR where suspended solids sedimentation could be avoided, low N-removal rates were observed in the absence of biofilm carrier elements whereas high N-removal rates were achieved in their presence. A simple one-stage process based on immobilized biomass could therefore be installed downstream of agricultural anaerobic digesters in order to mitigate undesirable gaseous ammonia emissions.     

Nitrogen removal from pharmaceutical manufacturing wastewater via nitrite and the process optimization with on-line control.

In this study, laboratory scale experiments were conducted to investigate the nitrogen removal from pharmaceutical manufacturing wastewater. The results indicate that by selective inhibition of free ammonia on oxidizers, nitrogen removal can be achieved by nitritation and denitritation process. The nitrite ratio was above 98% in the aerobic stage and the nitrogen removal efficiency was about 99%. The complete ammonia removal corresponded exactly to the "Ammonia Valley" in the pH versus time graphic and the anoxic reaction was completed when the "Nitrite Knee" appeared in the ORP versus time graphic. Optimization of the SBR cycle by step-feed and on-line control with pH and ORP strategy allowed the carbon and energy saving. The easy operation and the low cost make the SBR system an interesting option for the biological nitrogen removal from the pharmaceutical manufacturing wastewater.     

Achieving biological nitrogen removal via nitrite by salt inhibition.

The principal aim of this paper is to develop and evaluate an approach to obtain nitrogen removal bypassing nitrate. The method is based on the addition of sodium chloride (NaCI), selective inhibitor of nitrite oxidizers, to influent. Validation of the new method was conducted on laboratory-scale experiments applying the SBR activated sludge process to domestic wastewater with low C/N ratio. With the aerobic-anoxic sequence, three parallel SBRs achieving complete nitrification-denitrification are dosed by a certain concentration of NaCI to influent. The high nitrite accumulation, depending on the salinity in the influent and the application duration of salt, was obtained in SBRs treating saline wastewater. Optimum dosage and application duration of salt, which interact to determine the performance and stabilization of nitrite accumulation, were determined by experiment. In order to evaluate the method, the response of the biological treatment system to salt concentration was also explored. The repeatability of the method was further verified under various operational conditions. Microbial population tests supported the presumption that nitrite oxidizers are inhibited by salt addition and washed out of the system. The presented method is valuable to offer a solution to realize nitrogen removal via nitrite under normal conditions.     

Characteristics of denitrifying granular sludge grown on nitrite medium in an upflow sludge blanket (USB) reactor

While inoculating pre-acclimatized floccular sludge, nitrite-denitrifying granular sludge was obtained after approximately 40 days of cultivation in a 10 L upflow sludge blanket (USB) reactor. The nitrite removal efficiency was approximately 95% when the nitrite concentration was 50 mg L(-1)at an influent flow rate of 20 L h(-1). The nitrite granular sludge had several notable features including good settleability (110 m h(-1)), high ash content (79%), and high density (1.248 g cm(-3)). The mixed liquor suspended solids (MLSS) of the sludge bed remained at 130.04 g L(-1), at a hydraulic upflow velocity of 2 m h(-1). These interesting characteristics were attributed to a high effluent pH (9.7) caused by the release of alkalinity during the nitrite denitrification process. The surfaces of the granules were dominated by cocci bacteria with a diameter of approximately 3 μm, which could be classi?ed as Nitrosomonas-like species based on our analysis of 16 S rDNA sequences.     

Pilot-scale studies on biological treatment of hypersaline wastewater at low temperature.

In order to investigate the feasibility of biological treatment of hypersaline wastewater produced from toilet flushing with seawater at low temperature, pilot-scale studies were established with plug-flow activated sludge process at low temperature (5-9 degrees C) based on bench-scale experiments. The critical salinity concentration of 30 g/L, which resulted from the cooperation results of the non-halophilic bacteria and the halophilic bacteria, was drawn in bench-scale experiments. Pilot-scale studies showed that high COD removal efficiency, higher than 80%, was obtained at low temperature when 30 percent seawater was introduced. The salinity improved the settleability of activated sludge, and average sludge value dropped down from 38% to 22.5% after adding seawater. Seawater salinity had a strong negative effect on notronomonas and nitrobacter growth, but much more on the nitrobacter. The nitrification action was mainly accomplished by nitrosomonas. Bench-scale experiments using two SBRs were carried out for further investigation under different conditions of salinities, ammonia loadings and temperatures. Biological nitrogen removal via nitrite pathway from wastewater containing 30 percent seawater was achieved, but the ammonia removal efficiency was strongly related not only to the influent ammonia loading at different salinities but also to temperature. When the ratio of seawater to wastewater was 30 percent, and the ammonia loading was below the critical value of 0.15 kgNH4+-N/(kgMLSS.d), the ammonia removal efficiency via nitrite pathway was above 90%. The critical level of ammonia loading was 0.15, 0.08 and 0.03 kgNH4+-N/(kgMLSS.d) respectively at the different temperature 30 degrees C, 25 degrees C and 20 degrees C when the influent ammonia concentration was 60-80 mg/L and pH was 7.5-8.0.     

Nitrite accumulation by aeration controlled in sequencing batch reactors treating domestic wastewater.

The feasibility of obtaining and keeping stable nitrite accumulation in Sequencing Batch Reactors (SBRs) treating domestic wastewater is studied. The final product of ammonium oxidation is either reproducible nitrate or nitrite depending on the aeration strategy. With the aerobic-anoxic sequence, two SBRs fed with domestic wastewater are operated in parallel. One SBR (SBR1) is controlled by the aeration control strategy, and the other SBR (SBR2) by alternate aeration control strategy. Based on the on-line indirect measurements of DO and pH, the relationship between pH (or DO) and nitrogen concentration (NH4+-N, NO(3-)-N and NO(2-)-N) is investigated. The result indicates that pH and DO can be used as control parameters for the real-time aeration control strategy to obtain nitritation in SBR treating domestic wastewater. The result of SBR1 indicates that long-term stable nitritation is possible at 32+/-1 degrees C. The result of SBR2 indicates that the aeration control strategy is necessary for nitritation during the acclimation period, because the nitrite accumulation disappears when the aeration is extended.     

Isolation and characterization of a heterotrophic nitrifier from coke plant wastewater

This study investigated some factors affecting ammonium removal and nitrite accumulation by Alcaligenes faecalis C16, which was isolated from the activated sludge of a coking wastewater treatment plant. Nitrite was produced from ammonium only in the presence of citrate, acetate, meat extract, peptone or ethanol. The highest amount of nitrite was found with citrate as carbon source. A. faecalis C16 could not use glucose, fructose, sucrose and methanol. Under the optimum conditions of initial pH 6.0, C/N 14, 30 °C and 120 rpm, a maximum nitrite accumulation of 28.29 mg/L NO(2)(-)-N was achieved when the organism grew with citrate in four days. Nitrite accumulation increased with the increase of NH(4)(+)-N. Furthermore, A. faecalis C16 was shown to have phenol-degrading capacity during ammonium removal. Metabolism of phenol resulted in acidification of the media, which is not favorable for nitrification, whereas many other carbon sources made the medium more alkaline. However, no inhibitory effect by phenol was observed when phenol and acetate were used as mixed carbon source at different phenol/sodium acetate (P/S) ratios and their pH values were all controlled above 9.2 or P/S ratios below 5:5. These results suggested that A. faecalis C16 has some potential application in industrial wastewater treatment systems.     

The sharon process: An innovative method for nitrogen removal from ammonium-rich waste water

⁺ per litre has been developed at the Delft University of Technology. The SHARON process operates at a high temperature (30–40 °C) and pH (7–8). The process is performed without sludge retention. This enables the prevention of nitrite oxidation, leading to lower operational costs. Denitrification is used to control the pH. A full scale plant was designed (1500 m³) based on kinetic and stoichiometric parameters determined al 1.5.1. scale and model predictions. Total costs are estimated at about $1.7 per kg removed NH₄⁺-N. The first full scale SHARON plant will be operational at the Dokhaven waste water treatment plant in Rotterdam in the beginning of 1998. This contribution focuses on the principles of the process and evaluates conditions for which application seems feasible.     

Treatment of nitrogen-rich wastewater using partial nitrification and anammox in the CANON process.

Partial nitrification combined with Anammox in a single reactor (the CANON process) is an energy-efficient N-removal technology that could substantially lower the N-load of a WWTP by separate treatment of nitrogen-rich side streams, preventing the need for extensive expansion and reducing the total energy requirement. This study looks at the enrichment of Anammox from activated sludge and its application in the CANON process on lab-scale. The aim was to identify the critical process control parameters necessary for successful operation of CANON. An Anammox culture capable of removing 0.6 kg N/m3/d was enriched in 14 weeks in a sequencing batch reactor. Nitrifying biomass was inoculated into the Anammox reactor (10% v/v) together with limited oxygen supply (< 8 mL/min) to initiate the CANON process in continuous culture. The small flocs formed by the biomass (< 1000 microm) were sensitive to low O2 concentrations (< 0.1 mg/L) which prevented simultaneous nitrification and Anammox. Operation with 20 min aerobiosis and 30 min anaerobiosis was necessary to achieve sustained, completely autotrophic N-removal for an extended period at a rate of 0.08 kg N/m3/d. Essential process control parameters for stable CANON operation were the nitrite concentration, oxygen concentration, pH and the temperature.     

Rapid start-up of a nitrifying reactor using aerobic granular sludge as seed sludge

In this study, the effectiveness of aerobic granular sludge as seed sludge for rapid start-up of nitrifying processes was investigated using a laboratory-scale continuous stirred-tank reactor (CSTR) fed with completely inorganic wastewater which contained a high concentration of ammonia. Even when a large amount of granular biomass was inoculated in the reactor, and the characteristics of influent wastewater were abruptly changed, excess biomass washout was not observed, and biomass concentration was kept high at the start-up period due to high settling ability of the aerobic granular sludge. As a result, an ammonia removal rate immediately increased and reached more than 1.0 kg N/m(3)/d within 20 days and up to 1.8 kg N/m(3)/d on day 39. Subsequently, high rate nitritation was stably attained during 100 days. However, nitrite accumulation had been observed for 140 days before attaining complete nitrification to nitrate. Fluorescence in situ hybridization analysis revealed the increase in amount of ammonia-oxidizing bacteria which existed in the outer edge of the granular sludge during the start-up period. This microbial ecological change would make it possible to attain high rate ammonia removal.     

Reuse of treated wastewater and sewage sludge for fertilization and irrigation

The objective of the present work was to assess the short-term potential of treated wastewater and sewage sludge for ornamental lawn fertilization and irrigation. A field experiment was performed and the following treatments were considered: sewage sludge application + irrigation with public water; sewage sludge application + irrigation with treated wastewater; irrigation with public water; irrigation with treated wastewater (TW). Irrigation with treated wastewater showed a positive effect on lawn installation through higher growth of grass (1,667 cm) and higher dry matter yield (18,147 g m(-2)). These results represent a significant increase in the grass yield compared with public water irrigation. The grass height (2,606 cm) and dry matter yield (23,177 g m(-2)) increased even more, when sewage sludge produced in the wastewater treatment plant (WWTP) was applied to soil, which proves once more its benefits as an organic fertilizer. At the end of the experiment, an increase of some soil parameters (pH, electrical conductivity, organic matter, Ca2+, Na+, K+, Mg2+ and NH4+) was observed, indicating that treated wastewater irrigation can cause a soil sodization. This short-term study indicated that use of treated wastewater and sewage sludge for ornamental lawn fertilization and irrigation is an environmentally sustainable option for re-use of the WWTP by-products.     

pH-controlled reject-water-treatment

Dewatering of digested sludge causes significant internal nitrogen loading to a wastewater treatment plant Due to the high concentration of nitrogen it is more effective to treat the reject-water not directly in the main purification process but to apply a separate biological treatment procedure. The intermittent operation of sludge-press facilities, the high initial pH-value of reject-water and the quick loss of alkalinity during nitrification makes a reliable control of the process necessary. A sequencing batch reactor (SBR) with an operational control based on on-line measurement of the pH-value is well suited to meet this requirement Such a control system for discontinuous treatment of reject-water has been extensively tested and optimised in full-scale experiments since 1995. The closed loop control of the pH-value was developed to keep the bicarbonate concentration within an optimum range. At the WWTP Strass in western Austria stable nitrification rates of 50 to 60 mg NH4-N/1/h have been achieved (elimination of 200 kg nitrogen per day).     

A two-sludge system for simultaneous biological C, N and P removal via the nitrite pathway

Nitrogen removal via the nitrite pathway results in significant savings in both aeration costs and COD requirements for denitrification when compared to the conventional biological nitrogen removal process. Implementation of the nitrite pathway for simultaneous C/N/P removal in a single sludge system has a major drawback: the aeration phase disfavours denitrifying phosphorus removal. A possible configuration to overcome this issue is the utilisation of a two-sludge system where autotrophic and heterotrophic populations are physically separated. This paper experimentally demonstrates the feasibility of a nitrite-based two-sludge system with sequencing batch reactors (SBR) for the treatment of urban wastewater: a heterotrophic SBR with denitrifying PAOs for P removal and an aerobic SBR for N removal. Partial nitrification was attained in the autotrophic SBR so that shortcut biological nitrogen removal was achieved by using the anoxic dephosphatation activity of DPAOs. Finally, the effect of operating this system without pH control was studied using different influent pH values (pH = 6.8, 7.5 and 8.2) and, despite some efficiency lost due to the pH fluctuations, the system was able to remove most of the C, N and P present in the wastewater.