The magnetic properties of BiY<Subscript>2</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> nanoparticles doped with Cr ions

BiY₂Cr _x Fe_5?x O₁₂ (x = 0, 0.05, 0.1, 0.2, 0.3) nanocrystals were synthesized by using a sol-gel method. Samples were characterized by the powder X-ray diffraction (XRD), the thermal gravity analysis (TGA) and the differential thermal analysis (DTA), the vibrating sample magnetometer(VSM) and Mössbauer spectrums. The average sizes of the particles were determined by the Scherrer’s formula. The special Ms and Mössbauer spectra of BiY₂Cr _x Fe_5?x O₁₂ nanocrystals are researched at room temperature. It is seen that the special Mss of samples are initially increased with increasing Cr³⁺ content (x < 0.1), and decreased with increasing content of Cr³⁺ ions (x > 0.1).     

Enhancing the microwave dielectric properties of Sr<Subscript>2</Subscript>Ca<Subscript>3</Subscript>Ta<Subscript>4</Subscript>TiO<Subscript>17</Subscript> ceramics by Zr Substitution

The compositions in Sr₂Ca₃Ta₄Ti_1?xZr_xO₁₇ (0?≤?x?≤?0.12) series were designed and fabricated by solid state sintering method. All the compositions formed single phases and crystallized in an orthorhombic crystal structure. Zr substitution led to the enhancing of the microwave dielectric properties by tuning the τ_f value through zero and increased the Q_uf_o value from 12,540 to 14,970 GHz with a slight decrease in ε_r. In the present study, a good combination of ε_r ~?51, Q_uf_o ~?145,43 GHz and τ_f ~ 3 ppm/°C were obtained for Sr₂Ca₃Ta₄Ti_0.90Zr_0.1O₁₇ ceramic sintered at 1575 °C for 4 h.     

Growth and properties of LiCu<Subscript>2</Subscript>O<Subscript>2</Subscript>-NaCu<Subscript>2</Subscript>O<Subscript>2</Subscript> crystals

Platelike Li_{1 ? x} Na _x Cu₂O₂ single crystals up to 2 × 10 × 10 mm in dimensions have been grown by slowly cooling (1 ? x)Li₂CO₃·xNa₂O₂·4CuO melts in alundum crucibles in air. Li_{1 ? x} Na _x Cu₂O₂ solid solutions in the LiCu₂O₂-NaCu₂O₂ system have been shown to exist in the composition range 0.78 < x < 1. The temperature stability ranges of NaCu₂O₂ and LiCu₂O₂ are 780–930 and 890–1050°C, respectively. The Mössbauer spectra and electrical conductivity of the crystals have been measured.     

Solid-state reactions in the system Li<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>

The formation mechanisms of Li _x Na_{1 ?x} Ta _y Nb_{1 ? y} O₃ perovskite solid solutions in the Li₂CO₃-Na₂CO₃-Nb₂O₅-Ta₂O₅ system have been studied by x-ray diffraction, differential thermal analysis, thermogravimetry, IR spectroscopy, and mass spectrometry at temperatures from 300 to 1100°C. The results indicate that the synthesis of Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions involves a complex sequence of consecutive and parallel solid-state reactions. An optimized synthesis procedure for Li _x Na_{1 ? x} Ta _y Nb_{1 ? y} O₃ solid solutions is proposed.     

Influence of Nd doping on microwave dielectric properties of SrTiO<Subscript>3</Subscript> ceramics

Sr_1?x Nd _x TiO₃ (x?=?0.08–0.14) ceramics were prepared by conventional solid-state methods. The analysis of crystal structure suggested Sr_1?x Nd _x TiO₃ ceramics appeared to form tetragonal perovskite structure. The relationship between charge compensation mechanism, microstructure feature and microwave dielectric properties were investigated. Trivalent Nd³⁺ substituting Sr²⁺ could effectively decrease oxygen vacancies. This reduction and relative density were critical to improve Q?×?f values of Sr_1?x Nd _x TiO₃ ceramics. For ε _r values, incorporation of Nd could restrain the rattling of Ti⁴⁺ cations and led to the reduction of dielectric constant. The τ _f values were strongly influenced by tilting of oxygen octahedral. The τ _f values decreased from 883 to 650 ppm/°C with x increasing from 0.08 to 0.14. A better microwave dielectric property was achieved for composition Sr_0.92Nd_0.08TiO₃ at 1460 °C: ε _r ?=?160, Q?×?f?=?6602 GHz, τ _f ?=?883 ppm/°C.     

Rare-earth-doped PbTiO<Subscript>3</Subscript>-PbZrO<Subscript>3</Subscript> solid solutions

(Pb_{1 ? x} Ln _x )(Zr_0.53Ti_0.47)O₃ and (Pb_{1 ? x} Ln _x )(Zr_0.65Ti_0.35)O₃ (x = 0.02, 0.06; Ln = La, Pr, Gd, Yb) solid solutions have been prepared by modified solid-state synthesis using organic-ligand precursors. The solid solutions have been characterized by thermal analysis, IR spectroscopy, x-ray powder diffraction, and atomic force microscopy. All of them have a rhombohedrally distorted perovskite structure (sp. gr. R3c).     

Effects of Nd doping on the mechanical properties and electronic structures of Gd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript>: a first-principles-based study

Doping of cations in A₂B₂O₇-type pyrochlores, either on A or B site, can modify the physical properties of compounds significantly. In this work, the structural, thermo-mechanical and electronic properties of Nd-doped Gd₂Zr₂O₇ pyrochlores (Gd_2?yNd_yZr₂O₇ and Gd₂Zr_2?yNd_yO₇) have been investigated by density functional theory calculations. It is found that the Nd incorporation into Gd-site leads to the formation of Gd₂Zr₂O₇-Nd₂Zr₂O₇ solid solutions, which remain the pyrochlore-type structures, whereas the introduction of Nd into Zr-site induces a pyrochlore-to-defect fluorite structural transition. Further calculations show that Nd substitution for Gd-site has a minor effect on the thermal–mechanical and electronic properties of Gd₂Zr₂O₇. However, incorporation of Nd into Zr-site results in smaller Young’s modulus, better ductility, stronger elastic anisotropy and lower Debye temperature than pure Gd₂Zr₂O₇. In addition, the incorporation of Nd into Zr-site results in an increasing number of electrons locating at the Fermi level with the increasing concentration of substitutional Nd atoms, which eventually leads to an insulating-to-metallic transition. This study suggests that incorporation of Nd into Zr-site can be an alternative way to tune the mechanical, electronic, and thermal properties of Gd₂Zr₂O₇.     

Magnetization reversal and tunable exchange bias behavior in Mn-substituted NiCr<Subscript>2</Subscript>O<Subscript>4</Subscript>

Single phase samples of Ni(Cr_1?xMn _x )₂O₄ (x = 0–0.50) were synthesized by using sol–gel route. Investigation of structural, magnetic, exchange bias and magnetization reversal properties was carried out in the bulk samples of Ni(Cr_1?xMn _x )₂O₄. Rietveld refinement of the X-ray diffraction patterns recorded at room temperature reveals the tetragonal structure for x = 0 sample with I4₁/amd space group and cubic structure for x ≥ 0.05 samples with \( {\text{Fd}\bar{3}\text{m}} \) space group. Magnetization measurements show that all samples exhibit ferrimagnetic behavior, and the transition temperature (T_C) is found to increase from 73 K for x = 0 to 138 K for x = 0.50. Mn substitution induces magnetization reversal behavior especially for 30 at% of Mn in NiCr₂O₄ system with a magnetic compensation temperature of 45 K. This magnetization reversal is explained in terms of different site occupation of Mn ions and the different temperature dependence of the magnetic moments of different sublattices. Study of exchange bias behavior in x = 0.10 and 0.30 samples reveals that they exhibit negative and tunable positive and negative exchange bias behavior, respectively. The magnitudes of maximum exchange bias field of these samples are found to be 640 and 5306 Oe, respectively. Exchange bias in x = 0.10 sample originates from the anisotropic exchange interaction between the ferrimagnetic and the antiferromagnetic components of magnetic moment. The tunable exchange bias behavior in x = 0.30 sample is explained in terms of change in domination of one sublattice moment over the other as the temperature is varied.     

Preparation and Thermal Expansion of Calcium Iron Zirconium Phosphates with the NaZr<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> Structure

Ca_{0.5(1 + x)}Zr_2–xFe _x (PO₄)₃ phosphates have been synthesized by a sol–gel process. The individual compounds and solid solutions obtained crystallize in the NaZr₂(PO₄)₃ structure (trigonal symmetry, sp. gr. R\(\bar 3\)). Using high-temperature X-ray diffraction, we have determined their thermal expansion parameters in the temperature range from 25 to 800°C. With increasing x, the magnitudes of their linear thermal expansion coefficients and thermal expansion anisotropy decrease. Most of the synthesized phosphates can be rated as low-thermal-expansion compounds and can be regarded as materials capable of withstanding thermal “stress.”     

Ionic conductivity of BaF<Subscript>2</Subscript> + ZnF<Subscript>2</Subscript> + CdF<Subscript>2</Subscript> + YbF<Subscript>3</Subscript> optical fluoride ceramic

The electrical conductivity of an optical fluoride ceramic in the quaternary system BaF₂ + ZnF₂ + CdF₂ + YbF₃ has been determined in the temperature range 338–722 K using impedance spectroscopy (5 to 5 × 10⁵ Hz). The 500-K ionic conductivity of the ceramic is σ = 3.3 × 10^–4 S/cm, which corresponds to the electrical characteristics of single crystals of the best conducting nonstoichiometric M_1–x R _x F_{2 + x} (M = Sr, Ba; R = La–Nd; x = 0.3–0.5) fluorite phases. We have observed nonmonotonic variation (breaks) in temperature-dependent σ, which is due to competing fluoride ion transport processes in different parts of the ceramic sample. The highly conductive state of the BaF₂ + ZnF₂ + CdF₂ + YbF₃ fluoride ceramic seems to be due to the formation of structural regions corresponding to a Ba_1–x Yb _x F_{2 + x} solid solution.     

Synthesis and x-ray diffraction study of solid solutions in the Zn<Subscript>2</Subscript>SnO<Subscript>4</Subscript>-Zn<Subscript>2</Subscript>TiO<Subscript>4</Subscript>-Zn<Subscript>2</Subscript>ZrO<Subscript>4</Subscript> system

The multicomponent refractory oxide system Zn₂(Ti_aSn_b)_{1 ? x} Zr_xO₄ (a + b = 1; a: b = 1: 5, 1: 4, 1: 3, 1: 2, 1: 1, 1: 0, 2: 1, 3: 1, 4: 1; x = 0?1.0; Δx = 0.05) has been studied by x-ray diffraction, using samples prepared by melting appropriate oxide mixtures in a low-temperature hydrogen-oxygen plasma. Two phases, both with wide homogeneity ranges, have been identified: α-phase, with a cubic inverse spinel structure, and β-phase, with a tetragonal spinel structure. The phase boundaries in the system have been determined. Structural data are presented for about 100 solid solutions of different compositions.     

Electrical conductivity of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-Tm<Subscript>2</Subscript>O<Subscript>3</Subscript>-Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> solid solutions

New solid solutions, Bi_2?x?y Tm _x Nb _y O_3+δ, with tetragonal and cubic structures have been synthesized in the Bi₂O₃-Tm₂O₃-Nb₂O₅ system, and their electrical conductivity has been measured at temperatures from 670 to 1020 K. The 1020-K conductivity of the tetragonal solid solution Bi_1.8Tm_0.15Nb_0.05O_3+δ is comparable to that of Bi_1.75Tm_0.25O₃, the best conductor in the Bi₂O₃-Tm₂O₃ system.     

Very high thermal stability with excellent dielectric,and non-ohmics properties of Mg-doped CaCu<Subscript>3</Subscript>Ti<Subscript>4.2</Subscript>O<Subscript>12</Subscript> ceramics

In this work, the nominal CaCu_3?xMg_xTi_4.2O₁₂ (0.00, 0.05 and 0.10) ceramics were prepared by sintering pellets of their precursor powders obtained by a polymer pyrolysis solution method at 1100 °C for different sintering time of 8 and 12 h. Very low loss tangent (tanδ)?<?0.009–0.014 and giant dielectric constant (ε′) ～?1.1?×?10⁴–1.8?×?10⁴ with excellent temperature coefficient (Δε′) less than ±?15% in a temperature range of ??60 to 210 °C were achieved. These excellent performances suggested a potent application of the ceramics for high temperature X8R and X9R capacitors. It was found that tanδ values decreased with increasing Mg²⁺ dopants due to the increase of grain boundary resistance (R_gb) caused by the very high density of grain, resulting from the substitution of small ionic radius Mg²⁺ dopants in the structure. In addition, CaCu_3?xMg_xTi_4.2O₁₂ ceramics displayed non-linear characteristics with the significant enhancements of a non-linear coefficient (α) and a breakdown field (E_b) due to Mg²⁺doping. The high values of ε′ (14012), α (13.64) and E_b (5977.02 V/cm) with very low tanδ value (0.009) were obtained in a CaCu_2.90Mg_0.10Ti_4.2O₁₂ ceramic sintered at 1100 °C for 8 h.     

Effect of Ni<Superscript>2+</Superscript> substitution on crystal structure and microwave dielectric properties for MgZrNb<Subscript>2</Subscript>O<Subscript>8</Subscript> ceramics

Monoclinic structured Mg_1?xNi_xZrNb₂O₈ (0?≤?x?≤?0.12) ceramics were synthesized for the first time through traditional solid-state reaction process and pure phase were obtained in all range. Rietveld refinement was used to analyze the crystal structure. With the increase of Ni²⁺ substitution amount, ε _r decreased, Q?×?f rose first then fell, τ _f shifted for the positive direction. Bond ionicity, lattice energy and bond energy were separately calculated to investigate the correlations with microwave dielectric properties. Typically, ceramics samples with the composition of Mg_0.92Ni_0.08ZrNb₂O₈ sintered at 1280 °C for 4 h exhibited the optimum microwave dielectric properties: ε _r ?=?24.58, Q?×?f?=?74534.1 GHz, τ _f ?=???49.11 ppm/°C, which could be a promising material for application.     

Low temperature sintering and dielectric properties of Ba<Subscript>3</Subscript>(VO<Subscript>4</Subscript>)<Subscript>2</Subscript> microwave ceramics using Co<Subscript>2</Subscript>O<Subscript>3</Subscript> additives

The Ba₃(VO₄)₂–x wt% Co₂O₃ (x?=?0.5–5) ceramics were prepared by the solid state reaction method in order to reduce the sintering temperature. The effects of the Co₂O₃ additions on the phase composition, microstructures, sintering characteristics and microwave dielectric properties of Ba₃(VO₄)₂ ceramics are investigated by an X-ray diffractometer, a scanning electron microscope and a network analyzer. As a result, the Q?×?f value of 54,000 GH, the ε _r of 14.6 and the τ_f value of +58.5 ppm/°C were obtained in the sample of the Ba₃(VO₄)₂–3 wt% Co₂O₃ ceramic sintered at the temperature of 925 °C, which is capable to co-fire with electrode metal of high conductivity such as Ag (961 °C). Moreover, the Q?×?f values of the sample with Co₂O₃ higher than that of 3 wt% additions decreased because of the formation of Ba₂V₂O₇ phase.     

Synthesis and High-Temperature Heat Capacity of Dy<Subscript>2</Subscript>Ge<Subscript>2</Subscript>O<Subscript>7</Subscript> and Ho<Subscript>2</Subscript>Ge<Subscript>2</Subscript>O<Subscript>7</Subscript>

The Dy₂Ge₂O₇ and Ho₂Ge₂O₇ pyrogermanates have been prepared by solid-state reactions in several sequential firing steps in the temperature range 1237–1473 K using stoichiometric mixtures of Dy₂O₃ (or Ho₂O₃) and GeO₂. The heat capacity of the synthesized germanates has been determined as a function of temperature by differential scanning calorimetry in the range 350–1000 K. The experimentally determined C _p (T) curves of the dysprosium and holmium germanates have no anomalies and are well represented by the Maier–Kelley equation. The experimental C _p (T) data have been used to evaluate the thermodynamic functions of the Dy₂Ge₂O₇ and Ho₂Ge₂O₇ pyrogermanates: enthalpy increment H°(T)–H°(350 K), entropy change S°(T)–S°(350 K), and reduced Gibbs energy Ф°(T).     

Structure and electrical properties of MnO doped (Ba<Subscript>0.96</Subscript>Ca<Subscript>0.04</Subscript>)(Ti<Subscript>0.92</Subscript>Sn<Subscript>0.08</Subscript>)O<Subscript>3</Subscript> lead free ceramics

In this work, (Ba_0.96Ca_0.04)(Ti_0.92Sn_0.08)O₃–xmol MnO (BCTS–xMn) lead-free piezoelectric ceramics were fabricated by the conventional solid-state technique. The composition dependence (0 ≤ x ≤ 3.0 %) of the microstructure, phase structure, and electrical properties was systematically investigated. An O–T phase structure was obtained in all ceramics, and the sintering behavior of the BCTS ceramics was gradually improved by doping MnO content. In addition, the relationship between poling temperature and piezoelectric activity was discussed. The ceramics with x = 1.5 % sintering at temperature of 1330 °C demonstrated an optimum electrical behavior: d ₃₃ ~ 475 pC/N, k _p ~ 50 %, ε _r ~ 4060, tanδ ~ 0.4 %, P _r ~ 10.3 μC/cm², E _c ~ 1.35 kV/mm, T _C ~ 82 °C, strain ~0.114 % and \(d_{33}^{*}\) ~ 525 pm/V. As a result, we achieved a preferable electric performance in BaTiO₃-based ceramics with lower sintering temperature, suggesting that the BCTS–xMn material system is a promising candidate for lead-free piezoelectric ceramics.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> addition on the microstructure and electrical properties of LaMnO<Subscript>3</Subscript>-based NTC thermistors

A study to develop a new system of negative temperature coefficient thermistors for wide temperature range, A series of Mn-based perovskite-structured ceramics of composition (LaMn_1?x Al _x O₃)_0.9(Al₂O₃)_0.1 has been synthesized by conventional solid state reaction at 1350?°C. The X-ray diffraction patterns showed that for all the samples, the substitution of manganese by aluminum up to x?=?0.1 preserved the rhombohedral perovskite LaMnO₃-like phase. For x?=?0.2, apart from the LaMnO₃-like structure, a second perovskite phase based on the cubic LaAlO₃ structure was formed. For x?=?0.3 and 0.4, the phase present was LaAlO₃ -type structure. The grain sizes of the sintered body detected by scanning electron microscope were decreased with increasing Al₂O₃ content. The resistivity increases with increasing the Al content. The obtained values of ρ _25?°C and B _25/50 and E _a are in the range of 10–13103 Ω cm, 1813–2794 K, 0.156–0.241 eV, respectively. The resistance variation (ΔR/R) was <0.241% and the minimum value (0.0483%) was obtained for aging at 125?°C at 500 h. The aim of this work was explored new composite ceramics materials, which could be used as potential candidates for wide temperature range from ?100 to 500?°C thermistors applications.     

Influence of isovalent and heterovalent substitution for Bi<Superscript>3+</Superscript> and Fe<Superscript>3+</Superscript> on the properties of Bi<Subscript>2</Subscript>Fe<Subscript>4</Subscript>O<Subscript>9</Subscript>-based solid solutions

Bi_2–хLa_хFe₄O₉ and Bi₂Fe_4–2xTi_xCo_xO₉ ferrites have been prepared by solid-state reactions at a temperature of 1073 K. X-ray diffraction data indicate that, in the Bi_2–хLa_хFe₄O₉ system, the limiting degree of La³⁺ substitution for Bi³⁺ ions in Bi₂Fe₄O₉ does not exceed 0.05 and that the limiting degree of substitution in the Bi₂Fe_4–2xTi_xCo_xO₉ system lies in the range 0.05 < x < 0.1. The specific magnetization and specific magnetic susceptibility of the samples have been measured at temperatures from 5 to 300 K in a magnetic field of 0.86 T. The field dependences of magnetization obtained for the Bi_2–хLa_хFe₄O₉ and Bi₂Fe_4–2xTi_xCo_xO₉ ferrites at temperatures of 300 and 5 K demonstrate that partial isovalent substitution of La³⁺ for Bi³⁺ ions in Bi₂Fe₄O₉ and heterovalent substitution of Ti⁴⁺ and Co²⁺ ions for two Fe³⁺ ions leads to partial breakdown of the antiferromagnetic state and nucleation of a ferromagnetic state.     

Diffusion phase transition and impedance spectroscopy of Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/CuO co-doped BCZT lead-free ceramics

Perovskite type (Ba_0.85Ca_0.15?2x Bi_2x )(Zr_0.1Ti_0.9?x Cu _x )O₃ lead-free ceramics were prepared via a conventional solid-state reaction method. The phase structure, dielectric, ferroelectric properties and complex impedance were investigated in detail. XRD and dielectric measurements determined that single orthorhombic phase displayed in (Ba_0.85Ca_0.15)(Zr_0.1Ti_0.9)O₃ at room temperature. With the introduction of Bi₂O₃/CuO, the phase structure exhibited the mixture of orthorhombic and tetragonal phases, and then turned to single tetragonal phase. In contrast to the sharp dielectric transition of (Ba_0.85Ca_0.15)(Zr_0.1Ti_0.9)O₃ ceramics, a broad dielectric peak coupled with a slight decrease in Curie temperature was observed in (Ba_0.85Ca_0.15?2x Bi_2x )(Zr_0.1Ti_0.9?x Cu _x )O₃ ceramics with increasing x. The observed diffuse phase transition behavior was further confirmed by a couple of measurements with polarization loops and polarization current density curves. The structural and the composition fluctuations induced by ions doping should be responsible for the diffuse phase transition behavior. Furthermore, physical mechanisms of the conduction and relaxation processes were revealed by using impedance spectroscopy analyses. It was concluded that the conduction and relaxation processes were thermally activated, which was closely linked with the singly and doubly ionized oxygen vacancies.