Tunable luminescence properties and energy transfer of single-phase Ca<Subscript>4</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>O: Dy<Superscript>3+</Superscript>, Eu<Superscript>2+</Superscript> multi-color phosphors for warm white light

The novel Ca_4?x(PO₄)₂O: xDy³⁺ and Ca_4?x?y(PO₄)₂O: xDy³⁺, yEu²⁺ multi-color phosphors were synthesized by traditional solid-state reaction. The crystal structure, particle morphology, photoluminescence properties and energy transfer process were investigated in detail. The X-ray diffraction (XRD) results demonstrate that the products showed pure monoclinic phase of Ca₄(PO₄)₂O when x < 0.1. The scanning electron microscopy (SEM) indicated that the phosphors were grain-like morphologies with diameters of ~ 3.7–7.0 μm. Under excitation of 345 nm, Dy³⁺-doped Ca₄(PO₄)₂O phosphors showed multi-color emission bands at 410, 481 and 580 nm originated from oxygen vacancies and Dy³⁺. Interestingly, Ca₄(PO₄)₂O: Dy³⁺, Eu²⁺ phosphors exhibited blue emission band at 481 nm and broad emission band from 530 to 670 nm covering green to red regions. The energy transfer process from Dy³⁺ to Eu²⁺ was observed for the co-doped samples, and the energy transfer efficiency reached to 60% when Eu²⁺ molar concentration was 8%. In particular, warm/cool/day white light with adjustable CCT (2800–6700 K) and high CRI (R_a > 85) can be obtained by changing the Eu²⁺ co-doping contents in Ca₄(PO₄)₂O: Dy³⁺, Eu²⁺ phosphors. The optimized Ca_3.952(PO₄)₂O: 0.04Dy³⁺, 0.008Eu²⁺ phosphor can achieve the typical white light with CCT of 4735 K and CRI of 87.     

Directional solidification and growth characteristics of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Er<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript>/ZrO<Subscript>2</Subscript> ternary eutectic ceramic by laser floating zone melting

Directionally solidified Al₂O₃/Er₃Al₅O₁₂/ZrO₂ ternary eutectic ceramic in situ composite rods with length of 110 mm have been fabricated by laser floating zone melting. The microstructural characteristics of steady growth zone, initial growth zone and solid/liquid interface are investigated under high temperature gradient. In the steady growth zone, the eutectic spacing (λ) is rapidly decreased as increasing the growth rate (V), and the corresponding relationship between growth rate and eutectic spacing is determined to be λ = 11.14 × V ^?1/2. The temperature gradient has been measured to be about 5.3 × 10³ K/cm. In the initial growth zone, the melting process and temperature distribution are recorded by infrared thermal imager, and several unstable complex microstructures are observed. In the quenched zone, the regular eutectics with minimum eutectic spacing of 200 nm are obtained. Moreover, the solid/liquid interface during solidification shows convex interface morphology and the interface height is gradually decreased as increasing the growth rate. The eutectic growth behaviors at the center and edge of the as-grown rod are compared and discussed.     

Low temperature sintering and microwave dielectric properties of Li<Subscript>6</Subscript>Mg<Subscript>7</Subscript>Ti<Subscript>3</Subscript>O<Subscript>16</Subscript> ceramics with LiF additive for LTCC applications

Li₆Mg₇Ti₃O₁₆ ceramics were prepared by the conventional solid-state method with 1–5 wt% LiF as the sintering aid. Effects of LiF additions on the phase compositions, sintering characteristics, micro-structures and microwave dielectric properties of Li₆Mg₇Ti₃O₁₆ ceramics were investigated. The LiF addition could effectively lower the sintering temperature of Li₆Mg₇Ti₃O₁₆ ceramics from 1550 to 900 °C. For different LiF-doped compositions, the optimum dielectric permittivity (ε _r ) and quality factor (Q·f) values first increased and then decreased with the increase of LiF contents, whereas the temperature coefficient of resonant frequency (τ _f ) fluctuated between ??14.39 and ??8.21 ppm/°C. Typically, Li₆Mg₇Ti₃O₁₆ ceramics with 4 wt% LiF sintered at 900 °C exhibited excellent microwave dielectric properties of ε _r ?=?16.17, Q·f?=?80,921 GHz and τ _f ?=???8.21 ppm/°C, which are promising materials for the low temperature co-fired ceramics applications.     

Structure and electrical properties of MnO doped (Ba<Subscript>0.96</Subscript>Ca<Subscript>0.04</Subscript>)(Ti<Subscript>0.92</Subscript>Sn<Subscript>0.08</Subscript>)O<Subscript>3</Subscript> lead free ceramics

In this work, (Ba_0.96Ca_0.04)(Ti_0.92Sn_0.08)O₃–xmol MnO (BCTS–xMn) lead-free piezoelectric ceramics were fabricated by the conventional solid-state technique. The composition dependence (0 ≤ x ≤ 3.0 %) of the microstructure, phase structure, and electrical properties was systematically investigated. An O–T phase structure was obtained in all ceramics, and the sintering behavior of the BCTS ceramics was gradually improved by doping MnO content. In addition, the relationship between poling temperature and piezoelectric activity was discussed. The ceramics with x = 1.5 % sintering at temperature of 1330 °C demonstrated an optimum electrical behavior: d ₃₃ ~ 475 pC/N, k _p ~ 50 %, ε _r ~ 4060, tanδ ~ 0.4 %, P _r ~ 10.3 μC/cm², E _c ~ 1.35 kV/mm, T _C ~ 82 °C, strain ~0.114 % and \(d_{33}^{*}\) ~ 525 pm/V. As a result, we achieved a preferable electric performance in BaTiO₃-based ceramics with lower sintering temperature, suggesting that the BCTS–xMn material system is a promising candidate for lead-free piezoelectric ceramics.     

The magnetic properties of BiY<Subscript>2</Subscript>Fe<Subscript>5</Subscript>O<Subscript>12</Subscript> nanoparticles doped with Cr ions

BiY₂Cr _x Fe_5?x O₁₂ (x = 0, 0.05, 0.1, 0.2, 0.3) nanocrystals were synthesized by using a sol-gel method. Samples were characterized by the powder X-ray diffraction (XRD), the thermal gravity analysis (TGA) and the differential thermal analysis (DTA), the vibrating sample magnetometer(VSM) and Mössbauer spectrums. The average sizes of the particles were determined by the Scherrer’s formula. The special Ms and Mössbauer spectra of BiY₂Cr _x Fe_5?x O₁₂ nanocrystals are researched at room temperature. It is seen that the special Mss of samples are initially increased with increasing Cr³⁺ content (x < 0.1), and decreased with increasing content of Cr³⁺ ions (x > 0.1).     

Ultralow thermal conductivity of cerium-doped Nd<Subscript>2</Subscript>Zr<Subscript>2</Subscript>O<Subscript>7</Subscript> over a wide doping range

In this paper, we report an ultralow thermal conductivity and a high-temperature phase stability of the (Nd_1?x Ce _x )₂Zr₂O_7+x system over the temperature range from room temperature to 1600 °C and over a wide composition range (0.2 ≤ x ≤ 0.8), and the (Nd_1?x Ce _x )₂Zr₂O_7+x system is therefore considered a strong candidate material for the fabrication of next-generation high-temperature thermal barrier coatings. The observed thermal conductivities (0.65–1.0 W/mK) are about 60–40% lower than those of undoped Nd₂Zr₂O₇ over the same temperature range (100–700 °C) and indicate a glass-like behavior. For comparison, the variation in the thermal conductivity with the temperature of the (Gd_1?x Ce _x )₂Zr₂O_7+x system with similar point defects was also measured, and the observed behavior was almost the same as that of undoped Gd₂Zr₂O₇ and was mostly determined by phonon–phonon scattering (λ ∝ 1/T). The effect of point defect scattering and strong phonon scattering sources (rattlers) on the thermal conductivity is also discussed in this paper. The results of this study suggest that the ultralow thermal conductivity of (Nd_1?x Ce _x )₂Zr₂O_7+x can be attributed to the presence of rattlers because of the large difference between the ionic radii of the Nd³⁺ and Ce⁴⁺ ions.     

Influence of Nd doping on microwave dielectric properties of SrTiO<Subscript>3</Subscript> ceramics

Sr_1?x Nd _x TiO₃ (x?=?0.08–0.14) ceramics were prepared by conventional solid-state methods. The analysis of crystal structure suggested Sr_1?x Nd _x TiO₃ ceramics appeared to form tetragonal perovskite structure. The relationship between charge compensation mechanism, microstructure feature and microwave dielectric properties were investigated. Trivalent Nd³⁺ substituting Sr²⁺ could effectively decrease oxygen vacancies. This reduction and relative density were critical to improve Q?×?f values of Sr_1?x Nd _x TiO₃ ceramics. For ε _r values, incorporation of Nd could restrain the rattling of Ti⁴⁺ cations and led to the reduction of dielectric constant. The τ _f values were strongly influenced by tilting of oxygen octahedral. The τ _f values decreased from 883 to 650 ppm/°C with x increasing from 0.08 to 0.14. A better microwave dielectric property was achieved for composition Sr_0.92Nd_0.08TiO₃ at 1460 °C: ε _r ?=?160, Q?×?f?=?6602 GHz, τ _f ?=?883 ppm/°C.     

Very high thermal stability with excellent dielectric,and non-ohmics properties of Mg-doped CaCu<Subscript>3</Subscript>Ti<Subscript>4.2</Subscript>O<Subscript>12</Subscript> ceramics

In this work, the nominal CaCu_3?xMg_xTi_4.2O₁₂ (0.00, 0.05 and 0.10) ceramics were prepared by sintering pellets of their precursor powders obtained by a polymer pyrolysis solution method at 1100 °C for different sintering time of 8 and 12 h. Very low loss tangent (tanδ)?<?0.009–0.014 and giant dielectric constant (ε′) ～?1.1?×?10⁴–1.8?×?10⁴ with excellent temperature coefficient (Δε′) less than ±?15% in a temperature range of ??60 to 210 °C were achieved. These excellent performances suggested a potent application of the ceramics for high temperature X8R and X9R capacitors. It was found that tanδ values decreased with increasing Mg²⁺ dopants due to the increase of grain boundary resistance (R_gb) caused by the very high density of grain, resulting from the substitution of small ionic radius Mg²⁺ dopants in the structure. In addition, CaCu_3?xMg_xTi_4.2O₁₂ ceramics displayed non-linear characteristics with the significant enhancements of a non-linear coefficient (α) and a breakdown field (E_b) due to Mg²⁺doping. The high values of ε′ (14012), α (13.64) and E_b (5977.02 V/cm) with very low tanδ value (0.009) were obtained in a CaCu_2.90Mg_0.10Ti_4.2O₁₂ ceramic sintered at 1100 °C for 8 h.     

Strong up-conversion luminescence and electrical properties of SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> multifunctional ceramics by Er<Superscript>3+</Superscript> doping

Novel green-emitting piezoelectric ceramics of SrBi_4?x Er _x Ti₄O₁₅ (SBT-xEr) were prepared. Strong up-conversion with bright green (524 and 548 nm) and a relatively weak red (660 nm) emission bands were obtained under 980 nm excitation at room temperature, which is attributed to the intra 4f–4f electronic transition of (²H_11/2, ⁴S_3/2)–⁴I_15/2 and the transition from ⁴F_9/2 to ⁴I_15/2 of Er³⁺ ions, respectively. Simultaneously, Er³⁺ doping promotes the electrical properties. At 0.8 mol%Er, the optimal electric properties with high Curie temperature of T _c?~527?°C, large remanent polarization of 2P _r?~14.92 μC/cm² and piezoelectric constant of d ₃₃?~17 pC/N was achieved. As a multifunctional material, Er³⁺ doped SBT showed a great potential to be used in 3D-display, bio-imaging, solid state laser and optical temperature sensor.     

Influence of silver addition on microstructures and transport properties of La<Subscript>0.67</Subscript>Ca<Subscript>0.33</Subscript>MnO<Subscript>3</Subscript>:Ag<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> composites

In order to obtain high temperature coefficient of resistance (TCR) value of La_0.67Ca_0.33MnO₃:Ag _x (LCMO:Ag _x ) composites, samples with different Ag contents (x?=?0, 0.1, 0.2, 0.25, 0.3, and 0.5) were prepared by sol–gel method. X-ray diffraction analyses indicated that all samples had orthorhombic perovskite structures. As x increased, lattice parameters (a, b, c) and cell volumes underwent slight expansions. Interestingly, the addition of Ag dramatically affected TCR and magneto-resistance (MR) values. Elevated TCR value up to 53.46%·K^?1 at 277 K was observed for LCMO:Ag _x composites with added Ag at the composition of x?=?0.1. Meanwhile, MR value at 263 K reached 71% at the magnetic field of 1 T for samples with Ag composition of x?=?0.25. The increase in Mn⁴⁺/Mn³⁺ ratio and improvement in crystallization caused by added Ag was found responsible for the elevated values of TCR, MR, and T_p. These findings may have practical use in high-performance magneto-resistive manganites.     

Effects of LiF addition on the sintering behavior and microwave dielectric properties of Li<Subscript>2</Subscript>Mg<Subscript>3</Subscript>SnO<Subscript>6</Subscript> ceramics

Li₂Mg₃SnO₆ (abbreviation for LMS) ceramics doped with 1–4 wt% lithium fluoride (LiF) were prepared by the conventional solid-state reaction method. The effects of LiF addition on the phase compositions, sintering behaviors and microwave dielectric properties of LMS ceramics were investigated. A small amount of LiF addition could effectively decrease the sintering temperatures due to the liquid phase in the sintering process and induced no apparent degradation of the microwave dielectric properties. The optimized quality factor values for each composition firstly increased and then decreased with the increase of the LiF content. Whereas, the optimized dielectric permittivity increased with increasing of the LiF content. Distinguished microwave dielectric properties with a dielectric constant (ε _r) of 11.13, a quality factor (Q·f) of 104,750 GHz, and a temperature coefficient of resonant frequency (τ _f ) of ?10.83 ppm/°C were obtained for LMS ceramics sintered at 950?°C doped with 3 wt% LiF, which showed that the materials were suitable for the low temperature co-fired ceramics applications (LTCC).     

Magnetization reversal and tunable exchange bias behavior in Mn-substituted NiCr<Subscript>2</Subscript>O<Subscript>4</Subscript>

Single phase samples of Ni(Cr_1?xMn _x )₂O₄ (x = 0–0.50) were synthesized by using sol–gel route. Investigation of structural, magnetic, exchange bias and magnetization reversal properties was carried out in the bulk samples of Ni(Cr_1?xMn _x )₂O₄. Rietveld refinement of the X-ray diffraction patterns recorded at room temperature reveals the tetragonal structure for x = 0 sample with I4₁/amd space group and cubic structure for x ≥ 0.05 samples with \( {\text{Fd}\bar{3}\text{m}} \) space group. Magnetization measurements show that all samples exhibit ferrimagnetic behavior, and the transition temperature (T_C) is found to increase from 73 K for x = 0 to 138 K for x = 0.50. Mn substitution induces magnetization reversal behavior especially for 30 at% of Mn in NiCr₂O₄ system with a magnetic compensation temperature of 45 K. This magnetization reversal is explained in terms of different site occupation of Mn ions and the different temperature dependence of the magnetic moments of different sublattices. Study of exchange bias behavior in x = 0.10 and 0.30 samples reveals that they exhibit negative and tunable positive and negative exchange bias behavior, respectively. The magnitudes of maximum exchange bias field of these samples are found to be 640 and 5306 Oe, respectively. Exchange bias in x = 0.10 sample originates from the anisotropic exchange interaction between the ferrimagnetic and the antiferromagnetic components of magnetic moment. The tunable exchange bias behavior in x = 0.30 sample is explained in terms of change in domination of one sublattice moment over the other as the temperature is varied.     

Synthesis,photoluminescence properties of Sr<Subscript>1.95</Subscript>Ba<Subscript>0.05</Subscript>CeO<Subscript>4</Subscript>:Eu<Superscript>3+</Superscript> for LED applications

The Sr_1.95Ba_0.05 CeO₄:Eu³⁺ phosphors are synthesized by the solid-state reaction method. The samples are characterized using X-ray diffraction (XRD), diffuse reflectance spectroscopy and photoluminescence (PL) spectra. The XRD results reveal that the synthesized phosphors are genuine crystalline and belong to the orthorhombic structure. The intense PL emission is optimized from the PL spectra at various doping concentrations of europium ions. The results indicates that the phosphor can be effectively excited under 264 nm wavelength producing on intense emission spectrum of the synthesis material at 484 nm (blue region). The color purity of the phosphor is confirmed by CIE coordinates (x = 0.217, y = 0.265). The experimental data indicate that the prepared phosphors can be used as blue-emitting material in the field of illuminations and display devices.     

Photoluminescence of Ga<Subscript>2</Subscript>S<Subscript>3</Subscript>:Eu nanocrystals

The photoluminescence (PL) of Ga₂S₃-5 mol % Eu₂O₃ nanocrystals prepared by mechanical comminution of the initial compound has been studied in the temperature range from 77 to 300 K. It is established that the PL spectrum of nanocrystals, in comparison to that of a massive sample, extends over a broader wavelength interval (430–620 nm) and has two maxima (at 507 and 556 nm) instead of one. The intensity of emission from nanocrystals is significantly higher than that from the massive crystal. The halfwidth in both cases varies with the temperature in proportion to T ^1/2. The intensity of emission at 556 nm for nanocrystals depends on the temperature as lgI ～ 1/T, this dependence having three linear portions corresponding to an activation energy of 0.04, 0.16, and 0.43 eV. The PL bands with maxima at 507 and 556 nm are assigned to the intracenter 4f ⁶5d4f ⁷ transitions in Eu²⁺ ions.     

Enhanced red-emitting phosphor Na<Subscript>2</Subscript>Ca<Subscript>3</Subscript>Si<Subscript>2</Subscript>O<Subscript>8</Subscript>:Eu<Superscript>3+</Superscript> by charge compensation

A series of novel red-emitting Na₂Ca_3???x Si₂O₈:xEu³⁺ phosphors were synthesized by solid state reactions. The phosphors can strongly absorb 395 nm light, and show red emission with a good color purity. The excitation and emission spectra properties of Na₂Ca₃Si₂O₈:Eu³⁺ were characterized. Na₂Ca₃Si₂O₈:Eu³⁺ with self-compensated and alkali metal ions charge compensated approaches (2Ca²⁺→Eu³⁺ + M⁺, M?=?Li⁺, Na⁺, K⁺) have investigated, which found that the red emission of luminescent intensity can be greatly enhanced, and shows superior luminescent property to the commercial Y₂0₃S:Eu³⁺. The present work implies that the efficient charge compensated phosphors are promising candidates as red-emitting phosphor for w-LEDs.     

New NaSrPO<Subscript>4</Subscript>:Sm<Superscript>3+</Superscript> phosphor as orange-red emitting material

Sm³⁺-activated NaSrPO₄ phosphors could be efficiently excited at 403 nm, and exhibited a bright red emission mainly including four wavelength peaks of 565, 600, 646 and 710 nm. The highest emission intensity was found for NaSr _1?x PO₄: xSm³⁺ with a composition of x = 0.007. Concentration quenching was observed as the composition of x exceeds 0.007. The decay time values of NaSr_1?x PO ₄ : xSm³⁺ phosphors range from around 2.55 to 3.49 ms. NaSr_1?x PO₄: xSm³⁺ phosphor shows a higher thermally stable luminescence and its thermal quenching temperature T ₅₀ was found to be 350°C, which is higher than that of commercial YAG:Ce³⁺ phosphor and ZnS:(Al, Ag) phosphor. Because NaSr_1?x PO₄: xSm³⁺ phosphor features a high colour-rendering index and chemical stability, it is potentially useful as a new scintillation material for white light-emitting diodes.     

High-temperature heat capacity and vibrational spectra of Eu<Subscript>2</Subscript>Sn<Subscript>2</Subscript>O<Subscript>7</Subscript>

The Eu₂Sn₂O₇ compound has been prepared by solid-state reaction (by sequentially firing a stoichiometric mixture of Eu₂O₃ and SnO₂ in air at 1273 and 1473 K) and its heat capacity has been determined by differential scanning calorimetry in the temperature range 370–1000 K. The heat capacity data have been used to evaluate the thermodynamic properties of europium stannate: enthalpy increment H°(T)–H°(370 K), entropy change S°(T)–S°(370 K), and reduced Gibbs energy Ф°(T). Raman spectra of Eu₂Sn₂O₇ polycrystals with the pyrochlore structure have been measured in the range 200–1200 cm^–1.     

Enhancing the microwave dielectric properties of Sr<Subscript>2</Subscript>Ca<Subscript>3</Subscript>Ta<Subscript>4</Subscript>TiO<Subscript>17</Subscript> ceramics by Zr Substitution

The compositions in Sr₂Ca₃Ta₄Ti_1?xZr_xO₁₇ (0?≤?x?≤?0.12) series were designed and fabricated by solid state sintering method. All the compositions formed single phases and crystallized in an orthorhombic crystal structure. Zr substitution led to the enhancing of the microwave dielectric properties by tuning the τ_f value through zero and increased the Q_uf_o value from 12,540 to 14,970 GHz with a slight decrease in ε_r. In the present study, a good combination of ε_r ~?51, Q_uf_o ~?145,43 GHz and τ_f ~ 3 ppm/°C were obtained for Sr₂Ca₃Ta₄Ti_0.90Zr_0.1O₁₇ ceramic sintered at 1575 °C for 4 h.     

Effect of Ho-doping on structural,electrical and magnetic properties of La<Subscript>0.7</Subscript>Sr<Subscript>0.3</Subscript>MnO<Subscript>3</Subscript> ceramics prepared by Plasma-Activated Sintering

Different components of La_0.7?x Ho _x Sr_0.3MnO₃ (LHSMO, x = 0, 0.1, 0.2, 0.3) ceramics were fabricated by Plasma-Activated Sintering (PAS), so as to study the correlation between the contents of Ho³⁺ and the structural, electrical, magnetic properties. XRD and SEM confirmed that LHSMO ceramics prepared by PAS exhibited high-purity phase and dense microstructure. The measurement of electrical resistivity showed that the resistivity of LHSMO ceramics increased, and the metal–insulator transition temperature decreased with the increasing Ho-doping content. The resistivity data were then fitted using various empirical equations, and the conduction mechanism of LHSMO ceramics was found to be in accord with the electron–magnon scattering process in the low-temperature region and the small polaron hopping model in the high-temperature region. Lastly, we calculated the values of magnetoresistance of the LHSMO ceramics, which increased with increasing Ho-doping content, from 3.5% for x = 0 to 14.6% for x = 0.3. Therefore, the doping of Ho³⁺ into La_0.7Sr_0.3MnO₃ can effectively enhance the low-field magnetoresistance effect.     

Effect of Ni<Superscript>2+</Superscript> substitution on crystal structure and microwave dielectric properties for MgZrNb<Subscript>2</Subscript>O<Subscript>8</Subscript> ceramics

Monoclinic structured Mg_1?xNi_xZrNb₂O₈ (0?≤?x?≤?0.12) ceramics were synthesized for the first time through traditional solid-state reaction process and pure phase were obtained in all range. Rietveld refinement was used to analyze the crystal structure. With the increase of Ni²⁺ substitution amount, ε _r decreased, Q?×?f rose first then fell, τ _f shifted for the positive direction. Bond ionicity, lattice energy and bond energy were separately calculated to investigate the correlations with microwave dielectric properties. Typically, ceramics samples with the composition of Mg_0.92Ni_0.08ZrNb₂O₈ sintered at 1280 °C for 4 h exhibited the optimum microwave dielectric properties: ε _r ?=?24.58, Q?×?f?=?74534.1 GHz, τ _f ?=???49.11 ppm/°C, which could be a promising material for application.