Numerical analysis of external magnetic field for mitigating backward flow momentum in weld pool

The external magnetic field is applied to mitigating backward flow jet of molten metal in weld pool so that humping bead may be suppressed during high speed gas metal arc welding（GMAW）. Therefore, the external magnetic field distribution in workpiece is critical to understand the interaction mechanisms of the external magnetic field with molten metal flow. In this study, the steady state external magnetic field induced by excitation device is numerically analyzed by using the the finite element software ANSYS and the three dimensional static magnetic scalar method. The distribution of external transverse magnetic field By in workpiece and arc area is calculated, and the influence of excitation current and air-gap distance on the distribution of transverse magnetic field By has been discussed. The magnetic field distribution in workpiece is measured by using a Tesla-Meter and compared with the simulated result. It is found that both are in good agreement.     

Effect of groove angle and preheating temperature on temperature profile and fluid velocity in weld pool

The three dimensiotud transient weld pool dynamics are numerically analyzed ,for Forcearc welding, which is a new gas metal arc welding technology to get deep fusion penetration with smaller angle sf V groove to enhance welding efficiency significantly. The influence of groove angle and preheatin,g temperature on heat and .fluid .flow is studied and compared to get an optimal welding parameter. Good agreement is shown between the predicted and experimental results, such as weld bead cross-section and thermal cycles. It can he seen that an apprpriate groove angle could be used to replace high preheating temperature to get inproced penetration and thermal cycles.     

Numerical analysis of reverse dual-rotation friction stir welding process

A three-dimensional model of reverse dual-rotation friction stir welding （RDR-FSW） is developed to conduct the numerical simulation of heat generation and material flow during the process. The reverse rotation of the assisted shoulder and the tool pin is considered to model the heat generation rate. The predicted temperature difference between the advancing side and the retreating side in RDR-FSW is less than that in conventional FSW. There are two reverse flows during the RDR-FSW which is beneficial to the uniformity of the temperature profile. Due to the reverse rotation effects of the assisted shoulder, the predicted shape and size of thermal-mechanically affected zone （TMAZ） based on the iso-viscosity line are decreased greatly compared to the conventional FSW. It lays solid foundation for optimizing the process parameters in RDR-FSW.     

Experimental study of electron beam welded titanium alloy to chromium bronze joint with a vanadium sheet

Electron beam welding experiment of titanium alloy to chromium bronze with a vanadium filler metal was carried out. Microstructure of the joint was observed by optical microscopy and scanning electron microscopy. Tensile strength of the joint was evaluated. The fracture surface of the joint was also analyzed. The results showed that the addition of vanadium filler metal reduced the brittleness of joint by increasing the amount of vanadium-based solid solution in the weld. But the melting point of vanadium.filler metal was so high that large heat input was needed to completely melt the filler metal. Thus, a large amount of interfacial compounds were produced. The tensile strength of joint was 280 MPa with a brittle fracture mode.     

Analysis of metal transfer during electron beam welding with filler wire

The metal transfer mode of electron beam welding （EBW） with filler wire was studied experimentally. The spatial position between the electron beam and the filler wire was defined. Basing on the charge coupled device （CCD） visual sensing system, the metal transfer mode of filler wire was investigated. The results showed that there were five transfer modes during EBW process due to different wire feed rates and spatial positions between beam and filler wire, such as short-circuiting mode, molten metal bridge mode, small droplet mode, big droplet mode and mixed mode. By comparing the weld appearance of different transfer modes, the molten metal bridge transfer was proved to be the best transfer mode.     

Investigation on process and microstructure of Ti/Ni/Cu joints by electron beam welding

In this article, the electron beam welding of the Cu alloy （ QCrO. 8） with Ti alloy （TC4） sheet was processed and the joint microstructure as well as the welding process were studied. The results show that brittle reaction layer which was mainly composed of TiCu, Ti2Cu, Ti2Cu3 and TiCu2formed at the weld fusion line, regardless of welding on the middle or on the Cu side. The mechanical properties of the joint were severely deteriorated by the layer that tensile strength was only 89. 4 MPa for welding on the Cu side. The microstructure of the joint was improved with pure nickel as filler metal for the electron beam welding. The weld was mainly composed of solid solution. Intermetallic compound phase decreased signifwantly in fusion line compared with the joint without filler metal. The mechanical properties of the joint were obviously improved that the average tensile strength was 205.2 MPa and the bending strength was 413.3 MPa with O. 5 mm offset of electron beam on the Cu side.     

Numerical analysis of transient keyhole shape in pulsed current plasma arc welding

Based on the characteristics of ＂one keyhole in a pulse＂ in pulsed current plasma arc welding （PAW） , the transient variation process of weld pool in a pulse cycle is simulated through the establishment of corresponding heat source model. And considering the effects of gravitational force, plasma arc pressure and surface tension on the weld pool surface, the dynamic change features of the keyhole shape in a pulse cycle are calculated by using surface deformation equation. Experiments are conducted and validate that the calctdated weld fusion line is in good agreement with the experimental results.     

Effect of temperature field on flashes formation of continuous drive friction welding

On basis of the finite element software DEFORM, the 2D coupled thermo-mechanical model of continuous drive friction welding of ring parts is established. The temperature and the flashes during the welding process are investigated. The results of numerical simulation show that the temperature of friction surface is higher than that of other region and the peak temperature increases with the increase of welding time. During the process of friction stage, no flash appears because of the low temperature and the small axial friction pressure. At the forging stage, the flashes appear, whose dimensions and bending degree increase with the increase of welding temperature. Moreover, with the increase of rotational velocity and axial forging pressure, the dimensions and the bending degree of flashes of continuous drive friction welding increase.     

Prediction of wire transfer behaviors in laser hot wire welding

With preheating wire by resistance heat, laser hot wire welding improves process stability and wire deposition efficiency, which gives broad potential applications in sugracing and narrow gap welding. It is a critical issue to control the temperature of preheated wire in this process. The temperature which is so high that the wire fuses outside molten pool or so low that the wire cannot melt timely in the molten pool, results in poor wire transfer stability and bad weld formation. This paper is purposed to calculate the wire temperature for the prediction of wire transfer behavior under various welding parameters. A heat conduction model is set up. Heat sources of the wire include resistance heat and reflected laser, and the heat source of molten pool is laser. The calculated temperature of wire part outside the molten pool is verified by infrared ratio temperature measurement. The calculated temperature of wire part in the molten pool is verified by measurement of the molten pool size. Analyzing the wire temperature and welding process observed by the high speed video imaging, the temperature criteria of wire transfer behaviors are obtained. Thus, numerical simulation of the wire temperature can be used to predict wire transfer behaviors in laser hot wire welding.     

Numerical analysis of temperature profile and weld dimensions in laser ＋ GMAW hybrid welding of aluminum alloy T-joint

The temperature fields in the transient state and weld dimensions in laser ＋ gas metal arc welding （GMAW） hybrid welding of aluminum alloy T-joint for different welding conditions were calculated using the developed heat source model, and the effect of welding speed on them was analyzed. The results show that the temperature field for the first weld pass only shows the feature of GMAW and the one for the second weld pass has the characteristics of both laser welding and GMAW. Welding speed can affect greatly weld dimensions and temperature distribution. When welding speed reaches 3.5 m/min, the fusion zones of two weld passes are separated and the maximum peak temperature of thermal cycle on the workpiece surface decreases largely.     

Comparative study on the flow fields of three atomization nozzles

In this paper, the flow fields of three types of nozzles （ Hartmann, Laval and Laminar nozzles ） under the same conditions are simulated, and the corresponding to pressure, temperature, velocity and turbulence intensity are obtained. The results suggest that two crushing presents in the atomization process using Hartmann nozzle, but only one crushing presents in the atomization process using the other nozzles, through the comparative research on the flow field features of three types of nozzle. Furthermore, the shockwave plays a more important role in crushing of liquid metal than velocity.     

Gas dynamic control of properties of welded joints from high strength alloyed steels

Gas dynamic control in welding with consumable electrode in conditions of two-jet gas shielding and its impact on the processes in the welding area and properties of the welded joints from high strength alloyed steel 30HGSA is considered in the paper. The results of a comparative experimental study of controlling the properties of welded joints by changing the gas dynamics of the active shielding gas are given. The impact force of a shielding gas jet on the drop of the electrode metal is 12 times higher in conditions of two-jet gas shielding than in those of single jet shielding. It is found that gas dynamics of the active shielding gas jet determines the formation of the welded joints, their chemical properties and the properties of the welded joints from high strength alloyed steels. The consumable electrode welding method with two-jet gas shielding provides controlled dynamics in the welding area and allows controlling the transfer of the electrode metal, chemical composition of the weld, stabilizing the welding process, it ensures higher mechanical properties of the welded joints.     

Neural network prediction of the shunt current in resistance spot welding

An error back propagation （BP） neural network prediction model was established for the shunt current compensation in series resistance spot welding. The input variables for the neural network consist of the resistivity of the material, the thickness of workpiece and the spot spacing, and the shunt rate is outputted. A simplified calculation for the shunt rate was presented based on the feature of the constant-current resistance spot welding and the variation of the resistance in resistance spot welding process, and then the data generated by simplified calculation were used to train and adjust the neural network model. The neural network model proposed was used to predict the shunt rate in the spot welding of 20# mlid steel （in Chinese classification） （in 2. 0 mm thickness） and 10# mild steel （in 1.5 mm and 1.0 mm thickness）. The maximum relative prediction errors are, respectively, 2. 83%, 1.77% and 3.67%. Shunt current compensation experiments were peoCormed based on the neural network prediction model proposed to check the diameter difference of nuggets. Experimental results show that maximum nugget diameter deviation is less than 4% for both 10# and 20# mlid steels with spot spacing of 30 mm and 50 mm.     

Effects of rare earth elements on sulphur and phosphorus impurities in deposited metal

In order to reduce sulphur （ S ） and phosphorus （ P ） impurities in deposited metal, a small amount of rare earth （RE） lanthanum （ La） and yttrium （Y） were added into the coating ofE4303 electrode, a low carbon steel electrode. The microstructures of deposited metal were analyzed with metalloscope, and then the content of S and P was examined by energy dispenive X-ray spectrometer （ EDXS ）, and by wavelength dispersive X-ray fluorescence （XRF） spectrometer for further examination. The results show that the proper addition of La and Y can be beneficial to the desulfurization and dephosphorization of the deposited metal. Certainly, difference in the addition amount of La and Y could lead to various desulfurization and dephosphorization efficiency, in which the former is more obvious than the latter. With the proper amount of La attd Y, there is finer microstructure in deposited metal, and mechanical properties are improved as well. The S content in deposited metal with added La and Y decreases by 44. 44 wt. % , while the P content 6. 67 wt. %, compared with that in deposited metal without La and II.     

Microstructure and mechanical properties of laser welded joints of pure copper and 304 stainless steels

A continuous wave diode laser with an output power of 2.8 kW was used to join pure copper and 304 stainless steel with a thickness of 1 mm. The focused laser beam with a diameter of O. 8 mm was irradiated on the copper side of the butt joints. In process of laser welding, effects of processing primary parameters on tensile strength of the joints were investigated. The interfacial characterizations of the joints were investigated by metallographic microscope, scanning electron microscope （SEM） and energy dispersive X-ray spectroscope （EDS）. The results showed that the element diffusion and solution occur and metallurgical bonding was achieved between pure copper and 304 stainless steel. The maximum tensile strength of the joints was 209 MPa when the laser power of welding was 2. 4 kW and welding speed was 12 mm/s.     

TIG welding-brazing joint of aluminum to stainless steel with hot wire

TIG welding-brazing process with high frequency induction hot wire technology was presented to create joints between 5A06 aluminum alloy and SUS32! stainless steel using ER1100 filler wire with different temperature. The joints were evaluated by mechanical test and microstructural analyses. The welding procedure using hot fiUer wire （400 ℃ ） significantly increases strength stability by 71% and average value of tensile strength by 30. 8 % of the joints, compared with cold wire. The research of microstructures in interfaces and welded seams reveals that using 400 ℃ hot filler wire can decrease the thickness of intermetallic compounds （ IMCs ） from 6 to 3.5 txm approximately, which is the main reason of mechanical property improvement.     

Effects of particle density on depositing properties of WC-17Co by HVOF process

The in-flight and deposition properties of three types of WC-17 Co powder with different particle densities during a high-velocity oxygen fuel （HVOF） thermal spray process were investigated. Three types of powder exhibited similar velocity upon impact on the substrate surface. The powder with the lower particle density exhibited a higher temperature upon impingement process, resulting in the generation of a higher flattening ratio. Thus, the coating derived from the powder with the lower particle density possessed superior micro-hardness, porosity and surface roughness. However, the coating with the lowest particle density showed the poorest fracture toughness because of the generation of the largest amount of amorphous phase.     

Study of microstructures and of domestic X70 properties for girth welding pipeline steels

With the development of domestic pipeline steels, it is necessary to develop suitable welding technology which can improve the properties of the welded pipeline. In this paper, the microstructures and mechanical properties of domestic XTO pipeline steels and welded joints are discussed. The welding consumables of BOHLER E6010 and HOBART 81N1 are matched for girth welding. The following characteristics in heat-affected zone（ HAZ） are indicated that microstructures of intercritical HAZ（ ICHAZ） is finer and more uniform, the grain sizes of fine-grain HAZ （ FGHAZ） and subcritical HAZ （ SCHAZ） are smaller than that of coarse-grain HAZ（ CGHAZ）. The hardness, tensile strength and toughness of welded joints come up to the standard. The micrographs of impact specimens in welded joints are cleavage, quasi-cleavage and dimple which shows there is typical ductile rupture.     

Investigation on diffusion bonding of TiAl intermetallic to Ti3AlC2 ceramic with Ni interlayer

In this study, vacuum atmosphere. The diffusion bonding of TiAI alloy and Ti3AlC2 ceramic was carried out using Ni foil as interlayer in a interfacial microstructures and the mechanical properties of the diffusion bonded joints were evaluated. Result showed that the interfacial microstructure of the joint from TiAl to Ti3AlC2 side could be divided into Al3NiTi2 , AlNi2 Ti , Ni3 （ Al, Ti） , Ni , Ni3 （ Al , Ti） , Ni （ Al , Ti ） , Ni3Al ＋ TiC~ ＋ Ti3AlC2 , respectively. The shear strength test showed that an average value of 45.9 MPa was achieved. The crack propagated along the interface between TiAl intermetallic and Ni interlayer during the shear test. The mechanisms f or formation of those compound layers during bonding process and the determinant of the fracture location were also discussed.     

Ultrasonic C-scan inspection of brazed joint in thin panel honeycomb structure

The non-destructive testing of brazed joint in honeycomb structure with thin panel （ thickness ： 0. 2 mm） was studied by ultrasonic C-scan method. Samples with different types of artificial defect were designed; the characteristic signal and the main parameters of the test were determined by the pre-experiment, and then parameters were optimized by orthogonal design, finally the optimum process was verified by a single panel sample. The multiple reflection echoes were chosen as the characteristic signal. The optimal C-scan results were achieved when the 20 MHz focus probe was used, and the pass band range for received signal were selected as 8 - 17. 5 MHz. The defects such as incomplete penetration and core damage can be detected with ultrasonic C-scan, and the detection accuracy can reach to 1 ram.