Thermal properties of Li4/3Ti5/3O4/LiMn2O4 cell

The thermal properties of Li_4/3Ti_5/3O₄ and Li_1+xMn₂O₄ electrodes were investigated by isothermal micro-calorimetry (IMC). The 150-mAh g⁻¹ capacity of a Li/Li_4/3Ti_5/3O₄ half cell was obtained through the voltage plateau that occurs at 1.55 V during the phase transition from spinel to rock salt. Extra capacity below 1.0 V was attributed to the generation of a new phase. The small and constant entropy change of Li_4/3Ti_5/3O₄ during the spinel/rock-salt phase transition indicated its good thermal stability. Accelerated rate calorimetry confirmed that Li_4/3Ti_5/3O₄ has better thermal characteristics than graphite. The IMC results for a Li/Li_1+xMn₂O₄ half cell indicated less heat variation due to the suppression of the order/disorder change by lithium doping. The heat profiles of the Li_4/3Ti_5/3O₄/Li_1+xMn₂O₄ full cell indicated less heat generation compared with a mesocarbon-microbead graphite/Li_1+xMn₂O₄ cell.     

Synthesis, structure and electrochemical Li insertion behaviour of Li2Ti6O13 with the Na2Ti6O13 tunnel-structure

Li₂Ti₆O₁₃ has been prepared from Na₂Ti₆O₁₃ by Li ion exchange in molten LiNO₃ at 325 °C. Chemical analysis and powder X-ray diffraction study of the reaction product respectively indicate that total Na/Li exchange takes place and the Ti-O framework of the Na₂Ti₆O₁₃ parent structure is kept under those experimental conditions. Therefore, Li₂Ti₆O₁₃ has been obtained with the mentioned parent structure. An important change is that particle size is decreased significantly which is favoring lithium insertion. Electrochemical study shows that Li₂Ti₆O₁₃ inserts ca. 5 Li per formula unit in the voltage range 1.5-1.0 V vs. Li⁺/Li, yielding a specific discharge capacity of 250 mAh g⁻¹ under equilibrium conditions. Insertion occurs at an average equilibrium voltage of 1.5 V which is observed for oxides and titanates where Ti(IV)/Ti(III) is the active redox couple. However, a capacity loss of ca. 30% is observed due to a phase transformation occurring during the first discharge. After the first redox cycle a high reversible capacity is obtained (ca. 160 mAh g⁻¹ at C/12) and retained upon cycling. Taking into consideration these results, we propose Li₂Ti₆O₁₃ as an interesting material to be further investigated as the anode of lithium ion batteries.     

In situ X-ray diffraction studies of mixed LiMn2O4-LiNi1/3Co1/3Mn1/3O2 composite cathode in Li-ion cells during charge-discharge cycling

The structural changes of the composite cathode made by mixing spinel LiMn₂O₄ and layered LiNi_1/3Co_1/3Mn_1/3O₂ in 1:1 wt% in both Li-half and Li-ion cells during charge/discharge are studied by in situ XRD. During the first charge up to ∼5.2 V vs. Li/Li⁺, the in situ XRD spectra for the composite cathode in the Li-half cell track the structural changes of each component. At the early stage of charge, the lithium extraction takes place in the LiNi_1/3Co_1/3Mn_1/3O₂ component only. When the cell voltage reaches at ∼4.0 V vs. Li/Li⁺, lithium extraction from the spinel LiMn₂O₄ component starts and becomes the major contributor for the cell capacity due to the higher rate capability of LiMn₂O₄. When the voltage passed 4.3 V, the major structural changes are from the LiNi_1/3Co_1/3Mn_1/3O₂ component, while the LiMn₂O₄ component is almost unchanged. In the Li-ion cell using a MCMB anode and a composite cathode cycled between 2.5 V and 4.2 V, the structural changes are dominated by the spinel LiMn₂O₄ component, with much less changes in the layered LiNi_1/3Co_1/3Mn_1/3O₂ component, comparing with the Li-half cell results. These results give us valuable information about the structural changes relating to the contributions of each individual component to the cell capacity at certain charge/discharge state, which are helpful in designing and optimizing the composite cathode using spinel- and layered-type materials for Li-ion battery research.     

Eliminating the irreversible capacity loss of high capacity layered Li[Li0.2Mn0.54Ni0.13Co0.13]O2 cathode by blending with other lithium insertion hosts

The large irreversible capacity loss generally encountered with the high capacity layered oxide solid solutions between layered Li[Li_1/3Mn_2/3]O₂ and LiMO₂ (M = Mn, Ni, and Co) has been reduced by blending layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂, which is a solid solution between Li[Li_1/3Mn_2/3]O₂ and Li[Mn_1/3Ni_1/3Co_1/3]O₂, with spinel Li₄Mn₅O₁₂ or LiV₃O₈. The irreversible capacity loss decreases from 68 to 0 mAh g⁻¹ as the Li₄Mn₅O₁₂ content increases to 30 wt.% in the Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂-Li₄Mn₅O₁₂ composite and the LiV₃O₈ content increases to 18 wt.% in the Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂-LiV₃O₈ composite. The decrease in irreversible capacity loss is due to the ability of Li₄Mn₅O₁₂ or LiV₃O₈ to insert the extracted lithium that could not be inserted back into the layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ during the first cycle. The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂-LiV₃O₈ composite with ∼18 wt.% LiV₃O₈ exhibits a high capacity of ∼280 mAh g⁻¹ with little or no irreversible capacity loss and good cyclability.     

High-density spherical Li4Ti5O12/C anode material with good rate capability for lithium ion batteries

Li₄Ti₅O₁₂ is a very promising anode material for lithium secondary batteries. To improve the material's rate capability and pile density is considered as the important researching direction. One effective way is to prepare powders composed of spherical particles containing carbon black. A novel technique has been developed to prepare spherical Li₄Ti₅O₁₂/C composite. The spherical precursor containing carbon black is prepared via an “outer gel” method, using TiOCl₂, C and NH₃ as the raw material. Spherical Li₄Ti₅O₁₂/C powders are synthesized by sintering the mixture of spherical precursor and Li₂CO₃ in N₂. The investigation of TG/DSC, SEM, XRD, Brunauer–Emmett–Teller (BET) testing, laser particle size analysis, tap-density testing and the determination of the electrochemical properties show that the Li₄Ti₅O₁₂/C composite prepared by this method are spherical, has high tap-density and excellent rate capability. It is observed that the tap-density of spherical Li₄Ti₅O₁₂/C powders (the mass content of C is 4.8%) is as high as 1.71 g cm⁻³, which is remarkably higher than the non-spherical Li₄Ti₅O₁₂. Between 1.0 and 3.0 V versus Li, the initial discharge specific capacity of the sample is as high as 144.2 mAh g⁻¹, which is still 128.8 mAh g⁻¹ after 50 cycles at a current density of 1.6 mA cm⁻².     

Formation of the high lithium ion conducting phase from mechanically milled amorphous Li2S-P2S5 system

The fast ionic conducting structure similar to thio-Lithium Super Ionic Conductor (LISICON) phase is synthesized in the Li₂S-P₂S₅ system. The Li₂S-P₂S₅ glass-ceramics with the composition of xLi₂S·(100−x)P₂S₅ (75 ≤ x ≤ 80) are prepared by the heat-treatment of mechanically milled amorphous sulfide powders. In the binary Li₂S-P₂S₅ system, 78.3Li₂S·21.7P₂S₅ glass ceramic prepared by mechanical milling and subsequent heat-treatment at 260 °C for 3 h shows the highest conductivity of 6.3 × 10⁻⁴ S cm⁻¹ at room temperature and the lowest activation energy for conduction of 30.5 kJ mol⁻¹. The enhancement of conductivity with increasing x up to 78.3 is probably caused by the introduction of interstitial lithium ions at the Li sites which affects the Li ion distribution. The prepared electrolyte exhibits the lithium ion transport number of almost unity and voltage stability of 5 V vs. Li at room temperature.     

Basic molten salt process—A new route for synthesis of nanocrystalline Li4Ti5O12-TiO2 anode material for Li-ion batteries using eutectic mixture of LiNO3-LiOH-Li2O2

A nanocrystalline Li₄Ti₅O₁₂-TiO₂ duplex phase has been synthesized by a simple basic molten salt process (BMSP) using an eutectic mixture of LiNO₃-LiOH-Li₂O₂ at 400-500 °C. The microstructure and morphology of the Li₄Ti₅O₁₂-TiO₂ product are characterized by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The sample prepared by heat-treating at 300 °C for 3 h (S-1) reveals dense agglomerates of ultra-fine nanocrystalline Li₄Ti₅O₁₂; with heat treatment at 400 °C for 3 h (S-2), there is a duplex crystallite size (fine < 10 nm, and coarse > 20 nm) of Li₄Ti₅O₁₂-TiO₂; at 500 °C for 3 h (S-3), a much coarser and less-dense distribution of lithium titanate (crystallite size ∼15-30 nm) is observed. According to the results of electrochemical testing, the S-2 sample shows initial discharge capacities of 193 mAh g⁻¹ at 0.2 C, 168 mAh g⁻¹ at 0.5 C, 146 mAh g⁻¹ at 1 C, 135 mAh g⁻¹ at 2 C, and 117 mAh g⁻¹ at 5 C. After 100 cycles, the discharge capacity is 138 mAh g⁻¹ at 1 C with a capacity retention of 95%. The S-2 sample yields the best electrochemical performance in terms of charge-discharge capacity and rate capability compared with other samples. Its superior electrochemical performance can be mainly attributed to the duplex crystallite structure, composed of fine (<10 nm) and coarse (>20) nm nanoparticles, where lithium ions can be stored within the grain boundary interfaces between the spinel Li₄Ti₅O₁₂ and the anatase TiO₂.     

On the LiNi0.2Mn0.2Co0.6O2 positive electrode material

Layered LiNi_0.2Mn_0.2Co_0.6O₂ phase, belonging to a solid solution between LiNi_1/2Mn_1/2O₂ and LiCoO₂ most commercialized cathodes, was prepared via the combustion method at 900 °C for a short time (1 h). Structural, electrochemical and magnetic properties of this material were investigated. Rietveld analysis of the XRD pattern shows this compound as having the α-NaFeO₂ type structure (S.G. R-3m; a = 2.8399(2) ?; c = 14.165(1) ?) with almost none of the well-known Li/Ni cation disorder. SQUID measurements clearly indicate that the studied compound consists of Ni²⁺, Co³⁺ and Mn⁴⁺ ions in the crystal structure. X-ray analysis of the chemically delithiated Li_xNi_0.2Mn_0.2Co_0.6O₂ phases reveals that the rhombohedral symmetry was maintained during Li-extraction, confirmed by the monotonous variation of the potential-composition curve of the Li//Li_xNi_0.2Mn_0.2Co_0.6O₂ cell. LiNi_0.2Mn_0.2Co_0.6O₂ cathode has a discharge capacity of ∼160 mAh g⁻¹ in the voltage range 2.7-4.3 V corresponding to the extraction/insertion of 0.6 lithium ion with very low polarization. It exhibits a stable capacity on cycling and good rate capability in the rate range 0.2-2 C. The almost 2D structure of this cathode material, its good electrochemical performances and its relatively low cost comparing to LiCoO₂, make this material very promising for applications.     

High-rate nano-crystalline Li4Ti5O12 attached on carbon nano-fibers for hybrid supercapacitors

A lithium titanate (Li₄Ti₅O₁₂)-based electrode which can operate at unusually high current density (300 C) was developed as negative electrode for hybrid capacitors. The high-rate Li₄Ti₅O₁₂ electrode has a unique nano-structure consisting of unusually small nano-crystalline Li₄Ti₅O₁₂ (ca. 5-20 nm) grafted onto carbon nano-fiber anchors (nc-Li₄Ti₅O₁₂/CNF). This nano-structured nc-Li₄Ti₅O₁₂/CNF composite are prepared by simple sol-gel method under ultra-centrifugal force (65,000 N) followed by instantaneous annealing at 900 °C for 3 min. A model hybrid capacitor cell consisting of a negative nc-Li₄Ti₅O₁₂/CNF composite electrode and a positive activated carbon electrode showed high energy density of 40 Wh L⁻¹ and high power density of 7.5 kW L⁻¹ comparable to conventional EDLCs.     

Nanosized Li4Ti5O12/graphene hybrid materials with low polarization for high rate lithium ion batteries

We report a simple strategy to prepare a hybrid of lithium titanate (Li₄Ti₅O₁₂, LTO) nanoparticles well-dispersed on electrical conductive graphene nanosheets as an anode material for high rate lithium ion batteries. Lithium ion transport is facilitated by making pure phase Li₄Ti₅O₁₂ particles in a nanosize to shorten the ion transport path. Electron transport is improved by forming a conductive graphene network throughout the insulating Li₄Ti₅O₁₂ nanoparticles. The charge transfer resistance at the particle/electrolyte interface is reduced from 53.9 Ω to 36.2 Ω and the peak currents measured by a cyclic voltammogram are increased at each scan rate. The difference between charge and discharge plateau potentials becomes much smaller at all discharge rates because of lowered polarization. With 5 wt.% graphene, the hybrid materials deliver a specific capacity of 122 mAh g⁻¹ even at a very high charge/discharge rate of 30 C and exhibit an excellent cycling performance, with the first discharge capacity of 132.2 mAh g⁻¹ and less than 6% discharge capacity loss over 300 cycles at 20 C. The outstanding electrochemical performance and acceptable initial columbic efficiency of the nano-Li₄Ti₅O₁₂/graphene hybrid with 5 wt.% graphene make it a promising anode material for high rate lithium ion batteries.     

Li4Ti5O12/Sn composite anodes for lithium-ion batteries: Synthesis and electrochemical performance

Li₄Ti₅O₁₂/tin phase composites are successfully prepared by cellulose-assisted combustion synthesis of Li₄Ti₅O₁₂ matrix and precipitation of the tin phase. The effect of firing temperature on the particulate morphologies, particle size, specific surface area and electrochemical performance of Li₄Ti₅O₁₂/tin oxide composites is systematically investigated by SEM, XRD, TG, BET and charge-discharge characterizations. The grain growth of tin phase is suppressed by forming composite with Li₄Ti₅O₁₂ at a calcination of 500 °C, due to the steric effect of Li₄Ti₅O₁₂ and chemical interaction between Li₄Ti₅O₁₂ and tin oxide. The experimental results indicate that Li₄Ti₅O₁₂/tin phase composite fired at 500 °C has the best electrochemical performance. A capacity of 224 mAh g⁻¹ is maintained after 50 cycles at 100 mA g⁻¹ current density, which is still higher than 195 mAh g⁻¹ for the pure Li₄Ti₅O₁₂ after the same charge/discharge cycles. It suggests Li₄Ti₅O₁₂/tin phase composite may be a potential anode of lithium-ion batteries through optimizing the synthesis process.     

Nonflammable electrolyte for 3-V lithium-ion battery with spinel materials LiNi0.5Mn1.5O4 and Li4Ti5O12

The compatibility between dimethyl methylphosphonate (DMMP)-based electrolyte of 1 M LiPF₆/EC + DMC + DMMP (1:1:2 wt.) and spinel materials Li₄Ti₅O₁₂ and LiNi_0.5Mn_1.5O₄ was reviewed, respectively. The cell performance and impedance of 3-V LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ lithium-ion cell with the DMMP-based nonflammable electrolyte was compared with the baseline electrolyte of 1 M LiPF₆/EC + DMC (1:1 wt.). The nonflammable DMMP-based electrolyte exhibited good compatibility with spinel Li₄Ti₅O₁₂ anode and high-voltage LiNi_0.5Mn_1.5O₄ cathode, and acceptable cycling performance in the LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ full-cell, except for the higher impedance than that in the baseline electrolyte. All of the results disclosed that the 3 V LiNi_0.5Mn_1.5O₄/Li₄Ti₅O₁₂ lithium-ion battery was a promising choice for the nonflammable DMMP-based electrolyte.     

Structural evolution of ramsdellite-type LixTi2O4 upon electrochemical lithium insertion–deinsertion (0 ≤ x ≤ 2)

Structural evolution during topotactical electrochemical lithium insertion and deinsertion reactions in ramsdellite-like Li_xTi₂O₄ has been followed by means of in situ X-ray diffraction techniques. The starting Li_xTi₂O₄ (x = 1) exists as a single phase with variable composition which extends in the range 0.50 ≤ x ≤ 1.33. However, beyond the lower and upper compositional limits, two other single phases, with ramsdellite-like structure, are detected. The composition of these single phases are: TiO₂ upon lithium deinsertion and Li₂Ti₂O₄ upon lithium insertion. Both TiO₂ and Li₂Ti₂O₄ are characterized by narrow compositional ranges. The close structural relationship between pristine LiTi₂O₄ and the inserted and deinserted compounds together with the relative small volume change over the whole insertion–deinsertion range (not more than 1.1% upon reduction) is a guaranty for the high capacity retention after long cycling in lithium batteries. The small changes in cell parameters well reflect the remarkable flexibility of the ramsdellite framework against lithiation and delithiation reactions.     

High lithium ionic conductivity in the garnet-type oxide Li7−X La3(Zr2−X, NbX)O12 (X = 0-2)

Lithium garnet-type oxides Li_7−XLa₃(Zr_2−X, Nb_X)O₁₂ (X = 0-2) were synthesized by a solid-state reaction, and their lithium ion conductivity was measured using an AC impedance method at temperatures ranging from 25 to 150 °C in air. The lithium ion conductivity increased with increasing Nb content, and reached a maximum of ∼0.8 mS cm⁻¹ at 25 °C. By contrast, the activation energy reached a minimum of ∼30 kJ mol⁻¹ at the same point with X = 0.25. The potential window was examined by cyclic voltammetry (CV), which showed lithium deposition and dissolution peaks around 0 V vs. Li⁺/Li, but showed no evidence of other reactions up to 9 V vs. Li⁺/Li.     

Structural and transport properties of layered Li1+x(Mn1/3Co1/3Ni1/3)1−xO2 oxides prepared by a soft chemistry method

In this work structural and transport properties of layered Li_1+x(Mn_1/3Co_1/3Ni_1/3)_1−xO₂ oxides (x = 0; 0.03; 0.06) prepared by a “soft chemistry” method are presented. The excessive lithium was found to significantly improve transport properties of the materials, a corresponding linear decrease of the unit cell parameters was observed. The electrical conductivity of Li_1.03(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ composition was high enough to use this material in a form of a pellet, without any additives, in lithium batteries and characterize structural and transport properties of deintercalated Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ compounds. For deintercalated samples a linear increase of the lattice parameter c together with a linear decrease of the parameter a with the increasing deintercalation degree occurred, but only up to 0.4-0.5 mol of extracted lithium. Further deintercalation showed a reversal of the trend. Electrical conductivity measurements performed of Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ samples (y = 0.1; 0.3; 0.5; 0.6) showed an ongoing improvement, almost two orders of magnitude, in relation to the starting composition. Additionally, OCV measurements, discharge characteristics and lithium diffusion coefficient measurements were performed for Li/Li⁺/Li_1.03−y(Mn_1/3Co_1/3Ni_1/3)_0.97O₂ cells.     

High-rate performance of all-solid-state lithium secondary batteries using Li4Ti5O12 electrode

The all-solid-state Li–In/Li₄Ti₅O₁₂ cell using the 80Li₂S·20P₂S₅ (mol%) solid electrolyte was assembled to investigate rate performances. It was difficult to obtain the stable performance at the charge current density of 3.8 mA cm⁻² in the all-solid-state cell. In order to improve the rate performance, the pulverized Li₄Ti₅O₁₂ particles were applied to the all-solid-state cell, which retained the reversible capacity of about 90 mAh g⁻¹ at 3.8 mA cm⁻². The 70Li₂S·27P₂S₅·3P₂O₅ glass–ceramic, which exhibits the higher lithium ion conductivity than the 80Li₂S·20P₂S₅ solid electrolyte, was also used. The Li–In/70Li₂S·27P₂S₅·3P₂O₅ glass–ceramic/pulverized Li₄Ti₅O₁₂ cell was charged at a current density higher than 3.8 mA cm⁻² and showed the reversible capacity of about 30 mAh g⁻¹ even at 10 mA cm⁻² at room temperature.     

Lithium manganese oxides for rechargeable lithium batteries

Lithium manganese spinel compounds HT-LiMn₂O₄ (HT means high temperature) synthesized at > 700 °C have high capacity in the 4 V range (Li_xMn₂O₄, x ⩽ 1), However, lithium manganese oxides LT-LiMn₂O₄ (LT means low temperature) synthesized at temperatures lower than 400 °C, resemble to the spinel structure and tend to have a reduced capacity in the 4 V range. We investigated the factor of potential difference between the 4 V type and the 3 V type by using ⁷Li nuclear magnetic resonance (NMR) and electron spin resonance (ESR) measurements. It was found by using ⁷Li-NMR that there were two kinds of spectrum in these materials; in the 4 V type, the spectrum having about 530 ppm of chemical shift with spinning side band was mainly observed. On the other hand, in the 3 V type, the broad spectrum having about 760 ppm of chemical shift without spinning side band was mainly observed. There are two different lithium sites in the manganese spinel compound (space group of Fd3m), one is at the 8a site located far from the manganese ion and the other one is at the 16c site located close to the manganese ion. It is presumed that the spectrum having 530 ppm of chemical shift with spinning side band is corresponding to the 8a site, and the broad spectrum having 760 ppm of chemical shift without spinning side band is corresponding to the 16c site, with taking into consideration the influence of paramagnetic character of manganese on the lithium site which is closely related to the distance from the manganese ion.     

Effects of preparation conditions on the electrochemical and morphological characteristics of Li4Ti5O12 powders prepared by spray pyrolysis

Li₄Ti₅O₁₂ anode powders were prepared by post-treatment of the precursor powders obtained by spray pyrolysis at various preparation conditions. The precursor powders had fine size, narrow size distribution, dense inner structure and homogeneous composition when the flow rate of the carrier gas and the preparation temperature were 10 l min⁻¹ and 800 °C. The spherical shapes of the precursor powders obtained at the optimum preparation conditions maintained after post-treatment at a temperature of 800 °C. The mean sizes of the Li₄Ti₅O₁₂ powders were controlled by changing the concentrations of the spray solution. The initial discharge capacities and cycle properties of the Li₄Ti₅O₁₂ powders were strongly affected by the preparation temperatures of the precursor powders. The optimum preparation temperature of the precursor powders was 800 °C when the flow rate of the carrier gas was 10 l min⁻¹. The discharge capacities and cycle properties of the Li₄Ti₅O₁₂ powders were not affected by flow rates of the carrier gas. The Li₄Ti₅O₁₂ powders had good cycle properties irrespective of the concentrations of the spray solution. However, the Li₄Ti₅O₁₂ powders obtained from the spray solutions with high concentration above 0.5 M had high discharge capacities than those obtained from the spray solutions with low concentration below 0.1 M.     

Synthesis and electrochemistry of cubic rocksalt Li–Ni–Ti–O compounds in the phase diagram of LiNiO2–LiTiO2–Li[Li1/3Ti2/3]O2

On the basis of extreme similarity between the triangle phase diagrams of LiNiO₂–LiTiO₂–Li[Li_1/3Ti_2/3]O₂ and LiNiO₂–LiMnO₂–Li[Li_1/3Mn_2/3]O₂, new Li–Ni–Ti–O series with a nominal composition of Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ (0 ≤ z ≤ 0.5) was designed and attempted to prepare via a spray-drying method. XRD identified that new Li–Ni–Ti–O compounds had cubic rocksalt structure, in which Li, Ni and Ti were evenly distributed on the octahedral sites in cubic closely packed lattice of oxygen ions. They can be considered as the solid solution between cubic LiNi_1/2Ti_1/2O₂ and Li[Li_1/3Ti_2/3]O₂ (high temperature form). Charge–discharge tests showed that Li–Ni–Ti–O compounds with appropriate compositions could display a considerable capacity (more than 80 mAh g⁻¹ for 0.2 ≤ z ≤ 0.27) at room temperature in the voltage range of 4.5–2.5 V and good electrochemical properties within respect to capacity (more than 150 mAh g⁻¹ for 0 ≤ z ≤ 0.27), cycleability and rate capability at an elevated temperature of 50 °C. These suggest that the disordered cubic structure in some cases may function as a good host structure for intercalation/deintercalation of Li⁺. A preliminary electrochemical comparison between Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ (0 ≤ z ≤ 0.5) and Li_6/5Ni_2/5Ti_2/5O₂ indicated that charge–discharge mechanism based on Ni redox at the voltage of >3.0 V behaved somewhat differently, that is, Ni could be reduced to +2 in Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ while +3 in Li_6/5Ni_2/5Ti_2/5O₂. Reduction of Ti⁴⁺ at a plateau of around 2.3 V could be clearly detected in Li_1+z/3Ni_1/2−z/2Ti_1/2+z/6O₂ with 0.27 ≤ z ≤ 0.5 at 50 °C after a deep charge associated with charge compensation from oxygen ion during initial cycle.     

Development of high power lithium-ion batteries: Layer Li[Ni0.4Co0.2Mn0.4]O2 and spinel Li[Li0.1Al0.05Mn1.85]O4

Layer Li[Ni_0.4Co_0.2Mn_0.4]O₂ and lithium excess spinel Li[Li_0.1Al_0.05Mn_1.85]O₄ were compared as positive electrode materials for high power lithium-ion batteries. Physical properties were examined by Rietveld refinement of X-ray diffraction pattern and scanning electron microscopic studies. From continuous charge and discharge tests at higher currents and different temperature environments using 3Ah class lithium-ion batteries, it was found that both materials presented plausible battery performances such as rate capability, cyclability at 60 °C at elevated temperature, and low temperature properties as well.