MgO/APT催化剂酸碱性质对1,4-丁二醇单醋酸酯转化反应的影响

以Mg(NO3)2为镁源,采用等体积浸渍法制备系列镁改性凹凸棒土催化剂Mg O/APT,利用XRD、BET、FT-IR和TPD对催化剂进行表征。结果表明,Mg O/APT催化剂具有与凹凸棒土相同的晶相结构;随着Mg O负载量的增加,Mg O/APT的碱强度和碱含量显著增加,较强酸量明显减少,弱酸酸位增加。在固定床反应装置上,考察催化剂气相催化转化1,4-丁二醇单醋酸酯反应性能。结果表明,催化剂表面的酸碱性对1,4-丁二醇单醋酸酯气相转化反应的产物分布有显著影响。酸性为主的催化剂APT上有利于1,4-丁二醇单醋酸酯发生分子内酯交换环化反应生成四氢呋喃;而适量酸-碱活性位有助于实现1,4-丁二醇单醋酸酯发生脱水-水解反应,生成3-丁烯-1-醇及3-丁烯-1-醇醋酸酯,过多碱性位有助于1,4-丁二醇单醋酸酯发生酯水解反应生成1,4-丁二醇。     

Factors controlling the selectivity of V2O5 supported catalysts in the oxidative dehydrogenation of propane

The surface properties of a series of V₂O₅ catalysts supported on different oxides (Al₂O₃, H–Na/Y zeolite, MgO, SiO₂, TiO₂ and ZrO₂) were investigated by transmission electron microscopy and FTIR spectroscopy augmented by CO and NH₃ adsorption. In the case of the V₂O₅/SiO₂ system TEM images evidenced the presence of V₂O₅ crystallites, whereas such segregated phase was not observed for the other samples. VO_x species resulted widely spread on the surface of Al₂O₃, H–Na/Y zeolite, MgO and SiO₂, whereas on TiO₂ and ZrO₂ they are assembled in a layer covering almost completely the support. Furthermore, evidences for the presence in this layer of V–OH Brønsted acid sites close to the active centres were found. It is proposed that propene molecules primarily produced by oxydehydrogenation of propane can be adsorbed on this acid centres and then undergo an overoxidation by reaction with redox centres in the neighbourhood. This features could account for the low selectivity of V₂O₅/TiO₂ and V₂O₅/ZrO₂ catalysts.     

Photocatalytic oxidation of nitrogen oxide over titania–zeolite composite catalyst to remove nitrogen oxides in the atmosphere

The photooxidation of NO with oxygen over Hycom TiO₂ and zeolite (A and Y form zeolite: TiO₂-AZ and TiO₂-YZ) composite catalysts was studied to remove NO_x in the atmosphere. The photocatalytic oxidation activity of the titania in the composite catalyst in a proportion of AZ:TiO₂=3:7 is about three times larger than that in the bare titania. The adsorption behaviors of NO and NO₂ for the bare titania sample obey Langmuir adsorption equations of NO and NO₂, respectively. In the titania–zeolite composite catalysts, the adsorption data indicate the increase in the amount of NO adsorption on the TiO₂ phase and the decrease in the amount of NO₂ adsorption, compared with the bare titania. The acceleration of NO photooxidation rate, resulting from the increase in the amount of NO adsorbed and the decrease in the amount of NO₂ adsorbed, thus occurs on the TiO₂ phase. IR spectra, when irradiating the catalysts with UV, showed the immediate formation of nitrate and NO₂ species on the catalyst. The results lead to the conclusion that the zeolites promote the photocatalytic oxidation of NO over the titania.     

蒸气浸渍法制备完全无氯CuY催化剂及其氧化羰基化性能

以具有升华性质且易分解的乙酰丙酮铜为铜源,NH₄Y分子筛为载体,采用蒸气浸渍法制备了CuY催化剂,考察了其对甲醇氧化羰基化合成碳酸二甲酯的催化性能,并采用XRD、H₂-TPR和NH₃-TPD等表征手段研究了催化剂上铜物种的分散状态、催化活性中心的含量及催化剂的酸强度和浓度,发现铜物种在Y分子筛载体上高度分散,且Y分子筛载体的晶体结构保持完好。在N₂∶H₂=12∶1的气氛中,250℃还原得到的催化剂CuY/250催化活性中心含量最高,催化活性也达到了最佳,其甲醇转化率为11.1%,碳酸二甲酯的时空收率和选择性分别为200.5mg/(g·h)和60.3%。     

超声浸渍无机盐改性Hβ分子筛催化合成乙基蒽醌

采用超声浸渍法将无机盐Al₂(SO₄)₃、(NH₄)₂SO₄、Ce(NH₄)₂(NO₃)₆和Fe(NO₃)₃负载于Hβ分子筛上,通过NH₃-TPD、XRD和吡啶-IR对分子筛进行表征,考察改性前后分子筛酸性能和晶相的变化。将改性的Hβ分子筛用于催化乙苯和苯酐合成乙基蒽醌。结果表明,不同无机盐超声浸渍改性分子筛的催化效果差别较大,其中,每克分子筛负载0.2 g的Al₂(SO₄)₃的Alβ分子筛催化效果最好,苯酐转化率为45.67%,乙基蒽醌选择性为50.12%。分子筛的酸性能（包括酸量、酸种类和酸强度）对催化性能影响较大。     

Coke study on MgO-promoted Ni/Al2O3 catalyst in combined H2O and CO2 reforming of methane for gas to liquid (GTL) process

MgO-promoted Ni/Al₂O₃ catalysts have been investigated with respect to catalytic activity and coke formation in combined steam and carbon dioxide reforming of methane (CSCRM) to develop a highly active and stable catalyst for gas to liquid (GTL) processes. Ni/Al₂O₃ catalysts were promoted through varying the MgO content by the incipient wetness method. X-ray diffraction (XRD), BET surface area, H₂-temperature programmed reduction (TPR), H₂-chemisorption and CO₂-temperature programmed desorption (TPD) were used to observe the characteristics of the prepared catalysts. The coke formation and amount in used catalysts were examined by SEM and TGA, respectively. H₂/CO ratio of 2 was achieved in CSCRM by controlling the feed H₂O/CO₂ ratio. The catalysts prepared with 20 wt.% MgO exhibit the highest catalytic performance and have high coke resistance in CSCRM. MgO promotion forms MgAl₂O₄ spinel phase, which is stable at high temperatures and effectively prevents coke formation by increasing the CO₂ adsorption due to the increase in base strength on the surface of catalyst.     

高硅铝比小晶粒NaY分子筛/高岭土复合物的合成及其催化裂化性能

以两种不同粒径的高岭土为原料,采用水热法合成了高硅铝比小晶粒NaY分子筛/高岭土复合物,通过XRD、SEM、晶粒度分析和N₂物理吸附等表征手段对复合物进行了结构和形貌表征。结果表明,与商品NaY相比,高岭土合成样品的结构稳定性和水热稳定性显著提高,以细化高岭土为原料合成样品的晶粒尺寸达310 nm,比表面积达807 m²·g^-1。以改性NaY分子筛/高岭土复合物为活性组分制备了催化裂化催化剂,采用NH₃程序升温脱附(NH₃-TPD)技术对其酸性特征进行了分析,并在小型微反装置上对其重油催化裂化性能进行了评价。研究结果发现,随着骨架硅铝比增大,催化剂表面酸中心强度增加,而酸量下降。采用细化高岭土合成的NaY分子筛/高岭土复合物的分子筛晶粒更小,催化剂酸中心数量以及催化裂化性能均大幅度提升。随着高温焙烧高岭土/偏高岭土质量比的增加,合成产物中的高岭土基质含量增加,催化剂表面酸中心强度下降。以原料高温焙烧高岭土/偏高岭土质量比为0.5,骨架硅铝比为6.1(摩尔比)的样品制备的催化剂,去柴重油转化率高达85.4%,同时有高达64.2%的汽油收率,表现出优异的重油催化裂化性能。     

MgO-supported Mo, CoMo and NiMo sulfide hydrotreating catalysts

The most common preparation of high surface area MgO (100–500 m² g⁻¹) is calcination of Mg(OH)₂ obtained either by precipitation or MgO hydration or sol–gel method. Preparation of MoO₃/MgO catalyst is complicated by the high reactivity of MgO to H₂O and MoO₃. During conventional aqueous impregnation, MgO is transformed to Mg(OH)₂, and well soluble MgMoO₄ is easily formed. Alternative methods, that do not impair the starting MgO so strongly, are non-aqueous slurry impregnation and thermal spreading of MoO₃. Mo species of MoO₃/MgO catalyst are dissolved as MgMoO₄ during deposition of Co(Ni) by conventional aqueous impregnation. This can be avoided by using non-aqueous impregnation. Co(Ni)Mo/MgO catalysts must be calcined only at low temperature because Co(Ni)O and MgO easily form a solid solution. Literature data on hydrodesulfurization (HDS) activity of MgO-supported catalysts are often contradictory and do not reproduced well. However, some results suggest that very highly active HDS sites can be obtained using this support. Co(Ni)Mo/MgO catalysts prepared by non-aqueous impregnation and calcined at low temperature exhibited strong synergism in HDS activity. Co(Ni)Mo/MgO catalysts are much less deactivated by coking than their Al₂O₃-supported counterparts. Hydrodenitrogenation (HDN) activity of Mo/MgO catalyst is similar to the activity of Mo/Al₂O₃. However, the promotion effect of Co(Ni) in HDN on Co(Ni)Mo/MgO is lower than that on Co(Ni)Mo/Al₂O₃.     

Ni/Al_2O_3催化剂的CO_2-TPD表征

Ni/Al_2O_3催化剂是甲烷二氧化碳重整反应制取合成气研究最多、最具应用潜力的一种催化剂。通过对催化剂进行CO_2-TPD研究,考察还原态Ni/Al_2O_3催化剂的CO_2脱附特性。结果表明,浸渍法制备的Ni/Al_2O_3催化剂CO_2脱附曲线呈现双峰,分别在(60~65)℃和(350~380)℃出现高低温两个活性位;高温CO_2吸附量为3.0 cm~3·g~(-1),低温CO_2吸附量为24.0 cm~3·g~(-1)。催化剂的CO_2吸附量与其Ni含量无关。考察选用不同载体的CO_2脱附行为,发现以Al_2O_3为载体的催化剂CO_2吸附量是MgO和SiO_2为载体催化剂的2~4倍,以TiO_2为载体的催化剂几乎不吸附CO_2。     

NiO/Al_2O_3基催化剂的TPR特性研究

NiO/Al_2O_3基催化剂用于替代贵金属催化剂,被广泛应用于石油和石化领域生产过程的加氢、脱硫和脱氮。采用TPR方法,研究不同Ni含量NiO/Al_2O_3及不同载体的催化剂还原特性。结果表明,NiO/Al_2O_3催化剂在10%H_2-Ar气氛下,还原温度范围较宽,为(300~800)℃,其中,(500~600)℃还原速率最大;随着NiO含量的增加,起始还原温度降低,还原耗氢量按比例增加;以MgO为载体的NiO催化剂还原呈现双峰特征,以SiO2和TiO2为载体的NiO催化剂的初始还原温度比NiO/Al_2O_3催化剂降低(100~200)℃。     

Study on the supported Cu-based catalysts for the low-temperature water–gas shift reaction

This paper presents a study on the influence of support (Al₂O₃, MgO, SiO₂-Al₂O₃, SiO₂-MgO, β-zeolite, and CeO₂) of Cu-ZnO catalysts for the low-temperature water–gas shift reaction. Supported Cu-ZnO catalysts were prepared by the conventional impregnation method, followed by the H₂ reduction. The activity of Cu-ZnO catalysts for the water–gas shift (WGS) reaction was largely influenced by the kind of support; Cu-ZnO catalysts supported on Al₂O₃, MgO, and CeO₂ showed high activity, while those on SiO₂-Al₂O₃, SiO₂-MgO and β-zeolite showed less activity in the temperature range 423–523 K. XRD analysis demonstrated that the copper species were highly dispersed on the supports used in the present study, except for a MgO support. TPR results of a series of supported CuO-ZnO catalysts suggest that the reducibility of CuO is one of the important factors controlling the activity of the WGS reaction over the supported catalysts.     

Hydrodesulfurization of hindered dibenzothiophenes on bifunctional NiMo catalysts supported on zeolite–alumina composites

A series of NiMo catalysts supported on HNaY(x)–Al₂O₃ composites with different amounts of HNaY zeolite (x = 0, 5, 10, 20 and 100 wt.% of HNaY) was prepared and tested in the hydrodesulfurization (HDS) of dibenzothiophene (DBT) and 4,6-dimethyl-DBT (4,6-DMDBT). The catalysts were characterized by N₂ physisorption, X-ray diffraction (XRD), FT-IR spectroscopy of pyridine and nitrogen oxide adsorption (Py and NO-FT-IR), temperature-programmed reduction (TPR), scanning electron microscopy (SEM-EDX) and high-resolution transmission electron microscopy (HRTEM). It was found that the increase in the zeolite content causes changes in the acidic properties of the catalyst (number of acid sites) as well as in the characteristics of the deposited metallic species (location and dispersion). Different activity trends with the amount of the zeolite were found for the DBT and 4,6-DMDBT hydrodesulfurization on NiMo/HNaY-Al₂O₃ catalysts. As for the HDS of DBT the alumina-supported catalyst presents the highest activity. The incorporation of the zeolite causes an initial drop and then the recovery of activity with zeolite content. In contrast, for the 4,6-DMDBT the HDS activity always increases with zeolite content. These two different catalytic behaviors seem to be due to two opposite effects, which affect the contribution of the reaction routes available for the HDS of each reactant, these effects are: (i) the decrease of MoS₂ dispersion caused by the incorporation of zeolite to the catalyst and (ii) the increase of the proportion of Brönsted acid sites with zeolite content. The reaction product distribution indicates that both types of sites, coordinatively unsaturated sites (CUS) of the MoS₂ and zeolite Brönsted acid sites, participate in the 4,6-DMDBT and DBT transformations.     

Methane partial oxidation over NiO-MgO/Ce0.75Zr0.25O2 catalysts

Methane partial oxidation (MPO) is considered as an alternative method to produce hydrogen because it is an exothermic reaction to afford a suitable H₂/CO ratio of 2. However, carbon deposition on a catalyst is observed as a major cause of catalyst deactivation in MPO. In order to find suitable catalysts that prevent the carbon deposition, NiO-MgO/Ce_0.75Zr_0.25O₂ (CZO) supported catalysts were prepared via the co-impregnation (C) and sequential incipient wetness impregnation (S) methods. The amount of Ni loading was fixed at 15 wt-% whereas the amount of MgO loading was varied from 5 to 15 wt-%. The results revealed that the addition of MgO shifted the light-off temperatures to higher temperatures. This is because the Ni surface was partially covered with MgO, and the strong interaction between NiO and NiMgO₂ over CZO support led to the difficulty in reducing NiO to active Ni⁰ and thus less catalytic activity. However, among the catalysts tested, the 15Ni5Mg/CZO (S) catalyst exhibited the best catalytic stability for MPO after 18 h on stream at 750°C. Moreover, this catalyst had a better resistance to carbon deposition due to its high metallic Ni dispersion at high temperature.     

Feedstock recycling of agriculture plastic film wastes by catalytic cracking

Feedstock recycling by catalytic cracking of a real plastic film waste from Almeria greenhouses (Spain) towards valuable hydrocarbon mixtures has been studied over several acid catalysts. The plastic film waste was mostly made up of ambient degraded low-density polyethylene (LDPE) and ethylene-vinyl acetate (EVA) copolymer, the vinyl acetate content being around 4 wt.%. Nanocrystalline HZSM-5 zeolite (crystal size 60 nm) was the only catalyst capable of degrading completely the refuse at 420 °C despite using a very small amount of catalyst (plastic/catalyst mass ratio of 50). However, mesoporous catalysts (Al-SBA-15 and Al-MCM-41), unlike it occurred with virgin LDPE, showed fairly close conversions to that of thermal cracking. Nanocrystalline HZSM-5 zeolite led to 60 wt.% selectivity towards C₁---C₅ hydrocarbons, mostly valuable C₃---C₅ olefins, what would improve the profitability of a future industrial recycling process. The remarkable performance of nanocrystalline HZSM-5 zeolite was ascribed to its high content of strong external acid sites due to its nanometer dimension, which are very active for the cracking of bulky macromolecules. Hence, nanocrystalline HZSM-5 can be regarded as a promising catalyst for a feasible feedstock recycling process by catalytic cracking.     

Hydrogenation of carbon dioxide over copper-pyrochlore/zeolite composite catalysts

The hydrogenation of CO₂ was studied over composite catalysts obtained by mixing Cu-based methanol synthesis catalyst and HY zeolite. A mechanism associating methanol synthesis and MTG (methanol to gasoline) reaction allowed the formation of C₁-C₄ hydrocarbons. It was found that the catalytic behaviors of the composite catalysts were favorably influenced by the characteristics of the methanol synthesis catalysts. The Cu-La₂Zr₂O₇ catalyst we recently developed associated with HY zeolite exhibited interesting performances in hydrocarbon synthesis. The addition of ZrO₂ to Cu---La₂Zr₂O₇/HY enhanced the ability to produce hydrocarbons. Comparing composite catalyst systems prepared with different Cu-based methanol synthesis catalysts, the effect of Na contamination on methanol and hydrocarbon formation over composite catalysts were also discussed.     

Generation of H2O2 from H2 and O2 over zeolite beta containing Pd and heterogenized organic compounds

The catalytic generation of H₂O₂ from H₂ and O₂ has been studied over zeolite beta-supported Pd and zeolite beta-adsorbed organic compounds such as 1,4-benzoquinone (BQ), hydroquinone (HQ), azobenzene (AB) and hydrazobenzene (HAB). According to catalytic results, zeolite beta-supported Pd catalysts display effective performance relative to those prepared from other types of zeolites reported and Pd-loaded zeolite beta-adsorbed HQ catalysts show enhanced activity compared to zeolite beta-supported Pd catalysts. In situ UV–Vis spectroscopic study indicates that HQ can readily be converted to BQ reversibly under H₂ and air inside zeolite beta only in the presence of Pd. The results suggest that HQ acts as a strong hydrogen transfer agent to promote the production of H₂O₂ from H₂ and O₂ in cooperation with a Pd catalyst. By contrast, adsorption of BQ, AB and HAB induces suppression of the catalytic properties of Pd/zeolite beta.     

Fe-HZSM-5分子筛催化剂的甲醇制汽油动力学研究

通过水热晶化法,合成含有骨架杂原子Fe的Fe-HZSM-5分子筛催化剂,采用XRD、BET和NH3-TPD对催化剂进行表征,在微型固定床反应器中测定催化剂的甲醇制汽油的反应性能和反应动力学数据,对Fe-HZSM-5分子筛催化剂的甲醇制汽油本征动力学进行研究。结果表明,ZSM-5分子筛骨架引入杂原子Fe,可以增加对产物汽油选择性有利的弱酸量。采用Chen and Reagan建立的甲醇制汽油三集总动力学模型,通过Runge-Kutta法和最小二乘法对实验数据的回归计算,获得反应速率常数为k1=0.921×1012exp(-108 600/RT)、k2=0.155×1012exp(-116 400/RT)和k3=1.008×107exp(-96 130/RT)。以目标残差函数OF参数值为检验模型的标准,模拟值和实验值的相关系数R2均超过0.99。因此,Chen and Reagan建立的甲醇制汽油三集总动力学模型可以准确描述Fe-HZSM-5分子筛催化剂的甲醇制汽油反应动力学行为。     

Density functional theory and kinetic Monte Carlo simulation study the strong metal–support interaction of dry reforming of methane reaction over Ni based catalysts

Oxide supports modify electronic structures of supported metal nanoparticles,and then affect the catalytic activity associated with the so-called strong metal-support interaction(SMSI).We herein report the strong influence of SMSI employing Ni_4/α-MoC(111) and defective Ni_4/MgO(100) catalysts used for dry reforming of methane(DRM,CO_2+CH_4→2 CO+2 H_2) by using density functional theory(DFT) and kinetic Monte Carlo simulation(KMC).The results show that α-MoC(111) and MgO(100) surface have converse electron and structural effect for Ni_4 cluster.The electrons transfer from a-MoC(111) surface to Ni atoms,but electrons transfer from Ni atoms to MgO(100) surface;an extensive tensile strain is greatly released in the Ni lattice by MgO,but the extensive tensile strain is introduced in the Ni lattice by α-MoC.As a result,although both catalysts show good stability,H_2/CO ratio on Ni_4/α-MoC(111) is obviously larger than that on Ni_4/MgO(100).The result shows that Ni/α-MoC is a good catalyst for DRM reaction comparing with Ni/MgO catalyst.     

Ruthenium as oxidation catalyst: bridging the pressure and material gaps between ideal and real systems in heterogeneous catalysis by applying DRIFT spectroscopy and the TAP reactor

Two supported Ru catalysts were prepared by the chemical vapor deposition of Ru₃(CO)₁₂ on MgO and SiO₂ (MOCVD). TEM, XRD, and static H₂ chemisorption measurements confirmed that the Ru particle size was about 2 nm on both supports. Using in situ DRIFT (diffuse reflectance infrared Fourier transform) spectroscopy at atmospheric pressure it was found that the adsorption of CO on the reduced samples is clearly influenced by the supports whereas the adsorption of CO on the oxidized Ru catalysts is essentially independent of the support. O₂ chemisorption measurements showed that a thin RuO₂ surface layer was formed on both catalysts under oxidizing conditions at room temperature. The observed C–O stretching frequencies were found to be in good agreement with HREELS and LEED data reported for the RuO₂(1 1 0) single crystal surface. The catalytic activity was assessed under high-vacuum conditions using the TAP (temporal analysis of products) reactor by co-feeding CO and O₂. These conditions ensured that heat and mass transfer limitations were absent. Both supported Ru catalysts were found to be highly active and stable under the CO oxidation conditions even down to room temperature. The deactivation of the catalysts observed at room temperature was reversible and independent of the support. The turnover frequencies (number of CO₂ molecules per metal surface site per second) derived from steady-state measurements are in good agreement with data reported for the RuO₂(1 1 0) single crystal surface under UHV conditions. Based on the results of the DRIFTS (diffuse reflectance infrared Fourier transform spectroscopy) and the kinetic measurements supported RuO₂ is identified as the catalytically active phase. In addition, the turnover frequencies are in good agreement with data reported for Ru/SiO₂ at atmospheric pressure. Thus, both the materials and the pressure gap were bridged successfully.     

在不同构型分子筛催化剂中吸附和扩散的分子模拟

基于巨正则蒙特卡洛和分子动力学,对NH₃-SCR反应体系中吸附质分子（NO与NH₃）在不同拓扑结构沸石分子筛（LTL、FER、LEV、BEA、MOR、FAU、CHA和MFI）上的吸附和扩散特性进行系统研究。结果表明,对于全硅分子筛而言,其分子筛的拓扑结构影响NO与NH3在分子筛上的吸附,综合吸附量及吸附作用能发现,MFI和LEV分子筛对NO具有较优的吸附特性;MFI和BEA分子筛对NH₃ 具有较优的吸附特性。研究了Si与Al物质的量比对BEA分子筛吸附性能影响,结果表明,随着Si与Al物质的量比降低,分子筛自由体积逐渐增加,进而有助于分子筛催化剂对NO和NH₃的吸附。采用分子动力学模拟计算NO与NH₃在不同构型全硅分子筛上的扩散系数,发现具有三维直通道且孔径较大的分子筛催化剂有利于NO和NH₃在其孔道内部的扩散,MFI虽然具备三维孔道结构,但由于存在Z型交叉通道,一定程度阻碍了反应物分子的扩散。