基于限制广播域和节点剩余能量的按需路由算法研究

按需路由协议AODV的路由发现使用洪泛方式的扩散法,导致网络超负荷运行和拥塞,而且在选择转发路由时,总是选择最少跳数的路由,造成无线传感网络中节点能量不均,减少网络寿命.本文提出了AODV-DE算法,该算法引入广播域的概念,限制RREQ分组的转发范围,同时避免使用剩余能量低的节点转发数据分组,选择路由路径时选择总剩余能量最多的路径进行信息的传送.仿真结果表明,AODV-DE协议在路由开销、网络寿命和端到端的延迟这三个方面表现出了优势.     

一种贪婪地理路由协议的改进算法

贪婪转发策略广泛应用于无线传感网络(WSNs)的地理路由协议中,但是,该协议存在数据包丢失严重以及在遭遇路由空洞时路由效率低下的不足。为此,提出一种贪婪地理路由协议的改进算法,记为GPSR-I算法。GPSR-I算法在选择下一跳转发节点时,利用节点离目的节点距离、方向以及节点密度信息计算度量值,然后依据该度量值决策下一跳转发节点。仿真数据表明,与GPSR相比,GPSR-I算法能够有效降低平均端到端传输时延、路由开销,并提高了数据包传输率。     

一种改进的基于AODV的分簇路由协议

基于距离向量的按需路由协议AODV是移动Ad Hoc网络研究的热点之一.文中提出一种基于AODV的分簇路由协议CAODV,该协议通过增加分簇机制,将AODV协议改进为层次型的路由协议.与AODV协议仿真比较后可以看出,改进后的CAODV协议在分组转发率和路由开销方面的性能有较大提高.     

低开销的MANET网络按需路由协议

针对简单泛洪效率低的问题,提出了一个限制洪泛的高效的路由广播算法,通过Euclidean距离来限制路由发现过程中请求分组被转发的次数;研究了减少路由维护开销,并降低路由发现的频率的方法,提出了一个基于节点高度的路由修复与优化算法,该算法使用节点监听来对链路断裂的路由进行修复与优化.基于限制泛洪的高效的路由广播算法和路由修复优化算法,提出了一种新的低开销的MANET网络按需路由协议LOOR(low overhead on-demand routing).仿真结果表明,新协议增强了路由的顽健性,减少了路由跳数,降低了路由发现的频率,提高了数据分组递送率,并显著地降低了路由控制开销.     

基于网络编码的机会网络高效路由算法

针对采用Epidemic机制的机会网络路由算法在数据分组传送阶段存在通信冗余的问题,提出了一种基于网络编码的高效路由算法--NCBER(network-coding-based epidemic routing）。NCBER在传送数据分组的过程中使用主动异或网络编码和多播,并取消了 Request（请求）控制分组,从而减少数据分组的转发次数和控制分组数量,降低网络开销,缩短分组传输时延。理论分析和仿真结果表明,NCBER 算法在网络开销和数据分组端到端时延性能方面优于经典的Epidemic路由算法及其改进算法MRRMR（message redundancy removal of multi-copy routing）,并且使数据传送成功率保持在100%。     

一种基于动态概率转发的AODV路由协议

在Ad hoc网络(自组织网络)的路由建立过程中,由于AODV(Ad hoc按需距离矢量)路由采用洪泛方式转发RREQ(路由请求)消息会产生很多不必要的重传,很可能引发广播风暴而影响网络性能。文章提出了一种基于动态概率转发RREQ消息的改进方案,该方案根据邻居节点的个数选择不同的概率转发RREQ消息。仿真结果表明,在网络节点较多且网络比较稠密的情况下,改进方案能有效减少网络端到端时延,提高网络吞吐量和分组投递率。     

MTAODV:一种新的高速公路场景下VANET路由协议

在高速公路场景中,针对车辆间通信特性,在AODV的基础上提出了一种基于应用消息类型的改进路由协议(MTAODV).其核心思想是在路由建立过程中充分考虑VANET中应用消息的类型,从而减小路由请求洪泛范围,降低网络开销.仿真实验结果表明,与AODV协议相比,MTAODV协议能够有效地提高分组递交率,降低了路由开销,改善了分组时延和抖动.     

智能家居ZigBee网络的构建与路由优化

ZigBee网络技术是一项新兴的低成本、低功耗的短距离无线通信技术,在智能家居中有广阔的应用前景。介绍了智能家居中ZigBee的通讯协议和网络地址分配方法,并针对传统的AODVjr路由算法在路由过程中RREQ分组过量洪泛问题和Cluster-Tree算法只按父子关系选择路由问题,提出了一种改进路由算法。改进算法将AODVjr和Cluster-Tree算法相结合,引入邻居表,适当控制RREQ转发方向,并考虑节点最小剩余能量。仿真结果表明,改进算法可以减少路由开销,延长节点的生存时间,均衡网络负荷。     

HVSR：一种新型的基于地理位置的路由协议

Ad Hoc网络是由一组带有无线收发装置的移动终端组成的一个多跳临时性自治系统。网络中的每个移动终端是主机也是路由器,根据路由算法参与路由的建立和分组转发工作。基于位置的路由算法通过利用额外的位置信息消除了基于拓扑路由算法的局限性。基于位置信息的路由协议不仅具有较高的可靠性及对动态拓扑有更好的适应性,而且具有低开销,高效率和可扩展性。文章研究了基于网格位置服务的路由（GLS）协议,分析了其优点和不足,在此基础上改进得出了一种基于位置信息的路由协议HVSR。该路由协议与GLS路由协议相比具有更低的开销、更高的效率和可靠性。     

无线Mesh网络中基于链路状态的组播路由算法研究

参考移动AdHoc网络的MAODV的组播路由协议,结合无线Mesh网络的特性,及其对路由的影响,提出了一种基于链路稳定性的路由选择和基于链路可持续时间预测的组播路由改进算法MAODV-PPS,该算法是在选择路径时选取相对稳定的路径转发数据;并在维护路径的过程中,在预测可持续连接时间小于算法所规定的阀值时,主动激活路由修复。基于NS2对改进算法进行仿真,仿真结果证明了改进算法的有效性。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first